Jenn-Air JS42SEDUDW, JS48SEDUDW, JS42PPDUDB, JS48PPDUDB Installation Manual
JENN-AIR® SIDE BY SIDE
BUILT-IN REFRIGERATOR
REFRIGERADOR EMPOTRADO
DE DOS PUERTAS JENN-AIR
®
RÉFRIGÉRATEUR ENCASTRÉ
CÔTE À CÔTE JENN-AIR
®
W10681453A
For questions about features, operation/performance, parts, accessories, or service,
call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.
In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.
Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico,
llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.
En Canadá, llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.ca.
Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247)
Table of Contents / Índice / Table des matières ...................................................................................2
INSTALLATION GUIDE
GUÍA DE INSTALACIÓN
GUIDE D’INSTALLATION
ou visitez notre site Web à www.jennair.ca.
TABLE OF CONTENTS
REFRIGERATOR SAFETY...........................................................................3
MODELS....................................................................................................... 4
INSTALLATION REQUIREMENTS ............................................................. 4
Tools and Parts.........................................................................................4
Location Requirements............................................................................. 5
Electrical Requirements............................................................................6
Water Supply Requirements..................................................................... 6
Tipping Radius..........................................................................................7
Product Dimensions .................................................................................7
Door Swing Dimensions ...........................................................................8
Stainless Steel Series Side Panels ...........................................................9
ÍNDICE
SEGURIDAD DEL REFRIGERADOR........................................................ 18
MODELOS..................................................................................................19
REQUISITOS DE INSTALACIÓN.............................................................. 19
Herramientas y piezas ............................................................................19
Requisitos de ubicación .........................................................................20
Requisitos eléctricos...............................................................................21
Requisitos del suministro de agua ......................................................... 22
Arco de vuelco........................................................................................ 22
Medidas del producto.............................................................................23
Medidas de oscilación de las puertas....................................................24
Paneles laterales de la serie de acero inoxidable ..................................24
INSTALLATION INSTRUCTIONS............................................................. 10
Unpack the Refrigerator .........................................................................10
Reduce Tipping Radius ..........................................................................10
Move the Refrigerator into House ..........................................................10
Install Anti-Tip Boards ............................................................................ 11
Connect the Water Supply .....................................................................11
Plug in Refrigerator................................................................................. 13
Move Refrigerator to Final Location....................................................... 13
Level and Align Refrigerator ...................................................................13
Adjust Doors ........................................................................................... 14
Install Side Panel ....................................................................................15
Install Base Grille ....................................................................................15
Complete Installation..............................................................................16
Water System Preparation ..................................................................... 16
INSTRUCCIONES DE INSTALACIÓN...................................................... 25
Desempaque el refrigerador...................................................................25
Cómo reducir el arco de vuelco .............................................................25
Cómo hacer entrar el refrigerador en la casa ........................................ 26
Cómo instalar los tableros antivuelco.................................................... 26
Conexión del suministro de agua........................................................... 27
Cómo enchufar el refrigerador ............................................................... 28
Cómo mover el refrigerador a su ubicación final................................... 29
Nivelación y alineamiento del refrigerador.............................................29
Ajuste las puertas ................................................................................... 30
Cómo instalar el panel lateral................................................................. 31
Cómo instalar la rejilla de la base........................................................... 31
Cómo terminar la instalación.................................................................. 32
Preparación del sistema de agua...........................................................32
TABLE DES MATIÈRES
SÉCURITÉ DU RÉFRIGÉRATEUR ...........................................................33
MODÈLES ..................................................................................................34
EXIGENCES D’INSTALLATION................................................................ 34
Outillage et pièces ..................................................................................34
Exigences d’emplacement .....................................................................35
Spécifications électriques....................................................................... 36
Spécifications de l’alimentation en eau..................................................37
Rayon de basculement...........................................................................37
Dimensions du produit............................................................................38
Dimensions pour le pivotement des portes ...........................................39
Panneaux latéraux de la série de panneaux en acier inoxydable.......... 39
INSTRUCTIONS D’INSTALLATION .........................................................40
Déballage du réfrigérateur...................................................................... 40
Réduction du rayon de basculement..................................................... 41
Faire entrer le réfrigérateur dans le domicile.......................................... 41
Installation de planches antibasculement..............................................41
Raccordement à l’alimentation en eau................................................... 42
Branchement du réfrigérateur ................................................................44
Déplacement du réfrigérateur à l'emplacement final............................. 44
Réglage de l'aplomb et alignement du réfrigérateur..............................44
Ajustement des portes............................................................................ 45
Installation du panneau latéral................................................................ 46
Installation de la grille de la base ........................................................... 46
Achever l’installation............................................................................... 47
Préparation du système d’eau ...............................................................47
2
REFRIGERATOR SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
3
MODELS
†®TORX is a registered trademark of Saturn Fasteners, Inc.
Euro-Style Design
Features stainless steel wrapped doors with towel bar handles.
JS42SEDUDW JS48SEDUDW
INSTALLATION REQUIREMENTS
Tools and Parts
IMPORTANT:
■ Installer: Leave Installation Instructions with the homeowner.
■ Homeowner: Keep Installation Instructions for future
reference. Save these Installation Instructions for the local
electrical inspector’s use.
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
■ Cordless drill
■ Drill bits
■ Adjustable wrenches (2)
■ Phillips screwdriver
■ Small level
■ Appliance dolly
■ To rx
®†
T27 screwdriver
■ ¹¹⁄₃₂" nut driver
■ ³⁄₈" and ¹⁄₂" open-end wrenches
■ ⁵⁄₃₂" hex key
■ ¹⁄₄" and ⁵⁄₁₆" socket drivers
■ Tape measure
■ Utility knife
Pro-Style® Design
Features stainless steel wrapped doors and Pro-Style® handles
with diamond-etched grip.
JS42PPDUDB JS48PPDUDB
Parts Needed
■ #8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6)
■ 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2)
■ If you are connecting the water line directly to copper tubing
and not to a shutoff valve, you need a ferrule, a union, and a
¹⁄₄" (6.35 mm) compression fitting.
4
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
¹⁄₂"
(1,3 cm)
B
A
B
Dimension
The refrigerator can be recessed in an opening between cabinets
or installed at the end of a cabinet run using a side panel to
enclose the refrigerator.
IMPORTANT:
■ Observe all governing codes and ordinances.
■ It is recommended that you do not install the refrigerator near
an oven, radiator, or other heat source.
■ Do not install in a location where the temperature will fall
below 55°F (13°C).
■ Floor must support the refrigerator weight, more than 600 lbs
(272 kg), door panels and contents of the refrigerator.
■ Ceiling height must allow for side tipping radius. See “Tipping
Radius.”
■ Location should permit door to open fully. See “Door Swing
Dimensions.”
■ Location must permit top grille removal. See “Opening
Dimensions.”
Opening Dimensions
■ To avoid tipping during use, the solid soffit must be within 1"
(2.5 cm) maximum above the refrigerator. If the solid soffit is
higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
If anti-tip boards are needed, they must be installed to the rear
wall studs so that the bottom of the anti-tip board is 84"
(213 cm) from the floor. See “Install Anti-Tip Boards” for more
information.
NOTES:
■ A clearance of ¹⁄₂" (1.3 cm) must be maintained above the
top grille in order for the top grille to be removed.
■ Do not remove the foam gasket on top of the compressor
cover unless removal is necessary to fit the unit under a
soffit. Removal of the gasket will cause loss in cooling
efficiency.
■ If installing under a solid soffit, after installation raise the
leveling legs so that the gasket is pressed snugly against
the soffit.
■ A grounded 3 prong electrical outlet should be located within
a specified number of inches from the right-hand side
cabinets or end panel. See the chart following the graphic for
the number of inches required for your model. For more
information, see “Electrical Requirements.”
■ The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the floor or the
back wall. See “Water Supply Requirements” for more
information.
80" - 90"
(203-229 cm)
83¹⁄₂" (212.1 cm) min.
³⁄₄" (215 cm) max.
84
to bottom of solid soffit
77"
(196 cm)
A
Width
(see chart following)
6"
(15.2 cm)
1"
24"
(2.54 cm)
6"
(15.2 cm)
Dimension B
(as shown above)
7¹⁄₂"
(19.1 cm)
13¹⁄₂"
(34.3 cm)
6"
(15.2 cm)
(60.96 cm) min.
Width A
Model
42 41¹⁄₂" to 41³⁄₄"
48 47¹⁄₂" to 47³⁄₄"
(as shown above)
(105.4 cm to 106.1 cm)
(120.7 cm to 121.3 cm)
A. Gasket
B. Compressor cover
NOTE: Flooring under refrigerator must be at same level as the
room. Face of cabinetry must be plumb.
5
Electrical Requirements
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
24"
(60.96 cm) min.
1"
(2.54 cm)
6"
(15.2 cm)
6"
(15.2 cm)
6"
(15.2 cm)
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
IMPORTANT: If this product is connected to a GFCI (Ground Fault
Circuit Interrupter) protected outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Food quality
and flavor may be affected. If nuisance tripping has occurred, and
if the condition of the food appears poor, dispose of it.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, remove the top grille and turn the master
power switch to OFF or disconnect power at the circuit breaker
box.
When you are finished, turn ON the master power switch or
reconnect power at the circuit breaker box. Then reset the control
to the desired setting.
Water Supply Requirements
■ All installations must meet local plumbing code requirements.
■ The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. The right-hand side is recommended. The access hole
through the cabinet must be within ¹⁄₂" (12.7 mm) of the rear
wall.
NOTE: If the water shutoff valve is in the back wall behind the
refrigerator, it must be at an angle so that the tube is not
kinked when the refrigerator is pushed into its final location.
■ If the water shutoff valve is not in the cabinets, the plumbing
for the water line can come through the floor. A ¹⁄₂" (12.7 mm)
hole for plumbing should be drilled at least 6" (15.2 cm) from
the right or left hand side cabinet or panel. On the floor, the
hole should be no more than 1" (2.54 cm) away from the back
wall. See “Connect the Water Supply.”
■ If additional tubing is needed, use copper tubing and check
for leaks. Install the copper tubing only in areas where the
household temperatures will remain above freezing.
■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve
which reduces water flow and clogs more easily.
NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"
(6.35 mm) saddle-type shutoff valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Water Pressure
A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
■ Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■ Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
■ If your refrigerator has a water filter cartridge, it may further
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.
If you have questions about your water pressure, call a licensed,
qualified plumber.
6
Tipping Radius
A
25³⁄₈"
(64.5 cm)
84" (213.4 cm)
Power Cord
*83³⁄₈"
(211.8 cm)
*3
¹⁄₂" (8.9 cm)
³⁄₈"
(9.53 mm)
24¹⁄₈"
(61.3 cm)
23
¹⁄₂"
(59.7 cm)
23¹¹⁄₁₆"
(60.3 cm)
A
B
Be sure there is adequate ceiling height to stand the refrigerator
upright when it is moved into place.
■ The dolly wheel height must be added to the tipping radius
when a dolly is used.
■ If needed, the tipping radius can be reduced. See “Reduce
Tipping Radius.”
Side Tipping Radius
The side tipping radius varies depending upon the width of the
model. Use the chart provided to determine the side tipping
radius.
NOTE: Tip on side only.
Model Tipping Radius A
42 93" (236.2 cm)
48 96" (243.8 cm)
Product Dimensions
Side View
■ The depth from the front of the top grille to the back of the
refrigerator cabinet is 25³⁄₈" (64.5 cm).
■ The power cord is 84" (213 cm) long.
■ The water line attached to the back of the refrigerator is 5 ft
(1.5 m) long.
■ Height dimensions are shown with leveling legs extended ¹⁄₈"
(3 mm) below the rollers.
*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below
rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.
Top View
Model A B
42 Euro-Style 41" (104.1 cm) 2¹⁄₈" (5.3 cm)
48 Euro-Style 47" (119.4 cm) 2¹⁄₈" (5.3 cm)
42 Pro48 Pro-
Style
Style
®
®
41" (104.1 cm) 2⁵/₈" (6.67 cm)
47" (119.4 cm) 2⁵/₈" (6.67 cm)
7
Front View
*83³⁄₈"
(211.8 cm)
A
(see chart following)
130˚
130˚
90˚
90˚
110˚
110˚
47⁷⁄₈"
(121.6 cm)
41¹⁄₂"
(105.4 cm)
B
37
¹⁄₄"
(94.6 cm)
41
³⁄₈"
(105.1 cm)
A
130˚
130˚
90˚
90˚
110˚
110˚
51³⁄₈"
(130.5 cm)
44"
(111.8 cm)
39"
(99.1 cm)
43
⁷⁄₈"
(111.4 cm)
B
A
■ Width dimensions were measured from trim edge to
trim edge.
■ Height dimensions are shown with leveling legs extended ¹⁄₈"
(3 mm) below the rollers.
Door Swing Dimensions
The location must permit both doors to open to a minimum of 90°.
Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the
refrigerator and a corner wall.
NOTE: More clearance may be required if you are using overlay
panels, custom handles, or extended handles.
To adjust the door swing, see “Adjust Doors.”
42" (106.7 cm) Models
Model Width A (Trim edge to trim edge)
42 42¹⁄₄" (107.3 cm)
48 48¹⁄₄" (122.6 cm)
*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below
rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.
Model A B
Pro-Style
Euro 10¹/₄" (25.87 cm) 13³/₄" (34.88 cm)
®
10³/₄" (27.11 cm) 14¹/₄" (36.11 cm)
48" (121.9 cm) Models
Model A B
Pro-Style
Euro 11⁵/₈" (29.43 cm) 15¹¹/₁₆" (39.75 cm)
®
12³/₁₆" (30.84 cm) 16¹/₄" (41.16 cm)
8
Stainless Steel Series Side Panels
24¹⁄₈"
(61.3 cm)
23
¹⁄₂"
(59.7 cm)
23¹¹⁄₁₆"
(60.3 cm)
¹¹⁄₆₄"
(4.5 mm)
¹⁄₄"
(6.35 mm)
³⁄₁₆"
(4.7 mm)
⁷⁄₃₂"
(5.5 mm)
¹³⁄₃₂" (10 mm)
⁵⁄₈"
(15.7 mm)
A
A
A
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run. You
may choose an Inset, Flush, or Recessed Inset panel installation.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type of
installation you are planning.
NOTES:
■ The dimensions shown are actual product dimensions and
may not reflect the needed panel installation dimensions.
■ The side panel should be a minimum of ½" (1.27 cm) thick
to avoid warping.
■ If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on rear wall.
Refrigerator
Inset Installation Dimensions
1. Measure the distance from point A (as shown) to the back
wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side
panel to fit into the trim.
2. If the panel is more than ¹⁄₄" (6.35 mm) thick, rout the front
edge to allow the side panel to fit into the trim.
Flush Installation Dimensions
1. Measure the distance from point A (as shown) to the back
wall.
2. Attach the support board with a screw or adhesive that is
compatible with aluminum and wood.
Side Trim
Recessed Inset Installation Dimensions
1. Measure the distance from point A (as shown) to the back
wall.
2. Rout the front edge of the support board or attach a ¹⁄₄"
(6.35 mm) board to hold the panel in the cabinet side trim.
9
INSTALLATION INSTRUCTIONS
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
B BA
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
Unpack the Refrigerator
IMPORTANT:
■ Do not remove the film covering until the refrigerator is in its
operating location.
■ All four leveling legs must contact the floor to support and
stabilize the full weight of the refrigerator.
■ Keep the cardboard shipping piece or plywood under the
refrigerator until it is installed in the operating location.
1. Remove and save the literature package bag taped to the side
of the refrigerator and the parts bag behind the grille. Remove
the four brackets (two on each side) that attach the shipping
base to the refrigerator bottom.
NOTE: Do not remove tape and door bracing until the
refrigerator is in its final location.
2. If necessary, reduce the tipping radius. See “Tipping Radius”
for ceiling height requirements or “Reduce Tipping Radius” for
step-by-step instructions. If you do not need to reduce the
tipping radius, proceed to “Move the Refrigerator into House.”
Reduce Tipping Radius
(if required)
Before bringing the refrigerator into the home, be sure there is
adequate ceiling height to stand the refrigerator upright. See
“Tipping Radius” in the “Installation Requirements” section for
more information.
If you do not have adequate ceiling height to stand the refrigerator
upright, the tipping radius can be reduced by removing the top
grille and side trims (see the following chart).
1. Grasp both ends of the top grille.
10
Model Reduced Tipping
Radius
42 90¹⁄₂" (229.9 cm)
48 91¹⁄₄" (231.8 cm)
2. Push the top grille straight up; then pull straight out. Lay the
grille on a soft surface.
A. Top grille
B. Cabinet side trim
3. Remove the 6 screws attaching each cabinet side trim to the
refrigerator and remove the side trims.
Move the Refrigerator into House
1. Place an appliance dolly under the left side of the refrigerator
as shown. Place the corner posts from the packing materials
over the trims and handles as appropriate to avoid damage.
Slowly tighten the strap.
NOTE: Pass the dolly strap under the handles.
2. Place pieces of the shipping carton on the floor when rolling
BA
C
2" (5 cm)
D
A
B
C
the dolly and refrigerator into the house. Move the refrigerator
close to the built-in opening.
3. Place top of cardboard carton or plywood under refrigerator.
4. Stand the refrigerator up. First, place the left bottom edge of
the refrigerator on the floor, stand the refrigerator upright and
then lower the right-hand side of the refrigerator to the floor.
5. Reassemble the trim and top grille after the dolly has been
removed from the refrigerator.
Install Anti-Tip Boards
IMPORTANT:
■ To avoid tipping during use, the solid soffit must be within
1" (2.5 cm) maximum above the refrigerator. If the solid soffit is
higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
■ It is recommended that board(s) be installed before the
refrigerator is installed.
■ Board(s) must be long enough to fully cover the width of the
compressor cover.
■ Locate the board(s) so the bottom surface(s) of the board(s)
is(are) 84" (213 cm) from the floor.
■ During installation, raise the refrigerator up so there is
¹⁄₄" (6.35 mm) maximum between the top of the refrigerator
and the bottom of the anti-tip board(s). Do not crush the
compressor cover when raising the rear leveling legs.
NOTE: The foam gasket, on top of the compressor cover, will
compress to fit under the anti-tip board(s). There is no need to
trim the gasket.
To Install Anti-tip Boards
1. Mark the stud locations on rear wall.
2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x
81 cm) boards to wall studs behind refrigerator. Use six
#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws
must be screwed into the studs at least 1½" (3.8 cm). The
board(s) must overlap the compressor cover.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
Connect to Water Line
Parts Needed
■ Minimum 7 ft (2.13 m) flexible, codes approved water
supply line
Style 1—Shutoff Valve Connection
NOTE: If your water line connection does not look like Style 1, see
“Style 2—Copper Line Connection.”
1. Unplug refrigerator or disconnect power supply.
IMPORTANT:
■ There is not enough clearance to achieve a flush installation if
a water shutoff valve is located in the wall behind the
refrigerator. The water shutoff should be located in the base
cabinet on either side of the refrigerator.
■ Before attaching the tubing to shutoff valve, flush the main
water supply line to remove particles and air in the water line.
Allow enough flow so that water becomes clear. Flushing the
water line may help avoid filters and/or water valves from
becoming clogged.
2. Connect the flexible, codes approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve as shown.
A. Center board
above refrigerator
B. Two 2" x 4" x 32" (5 cm x 10 cm x
81 cm) boards
¹⁄₄
" (6.35 mm) max.
C. Attach to studs with six
D. Compressor cover
#8 x 3" (7.6 cm) screws
A. Bulb
B. Nut
C. Water tubing
3. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
4. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
11
Style 2—Copper Line Connection
A
B
C
DEF
G
1"
(2.54 cm)
7"
(17.78 cm)
6"
(15.2 cm)
6"
(15.2 cm)
A
B
C
D
E
F
G
NOTE: If there is a water supply line that meets the specifications
in “Water Supply Requirements,” proceed to “Connecting to
Refrigerator.” If not, use the following instructions to connect to
the household cold water supply.
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
■ Make sure it is a cold water pipe.
■ Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and keep normal sediment from collecting in the
valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the refrigerator to the water pipe. Add
7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D.
(outside diameter) copper tubing. Be sure both ends of copper
tubing are cut square.
5. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold
water pipe you have selected.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten.
IMPORTANT: Before attaching the tubing to shutoff valve, flush
the main water supply line to remove particles and air in the water
line. Allow enough flow so that water becomes clear. Flushing the
water line may help avoid filters and/or water valves from
becoming clogged.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten the
clamp or the sleeve. This will crush the copper tubing.
8. Turn off the shutoff valve on the water pipe. Coil the copper
tubing.
9. Connect the flexible, codes approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve.
10. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
11. Check for leaks around the saddle valve. Tighten any nuts or
connections (including connections at the valve) that leak.
E. Compression sleeve
F. Shutoff valve
G. Packing nut
Connect to Refrigerator
Parts Supplied
■ ¹⁄₄" to ¹⁄₄" (6.35 mm to 6.35 mm) male-to-male coupling
NOTE: The flexible, codes approved water supply line should
connect to the supply valve through the floor.
1. Unplug the refrigerator or disconnect power.
2. Connect the 7 ft (2.13 m) flexible codes approved water tube
to the water supply valve.
3. Flush the main water supply line to remove particles and air in
the water line. Allow enough flow so that water becomes clear.
4. Tape the 7 ft (2.13 m) flexible codes approved water supply
line to the floor, 7" (17.78 cm) from the left side of the
refrigerator. Tape along the length of the tubing, which will
allow it to pass beneath the refrigerator without interference.
NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes
approved water supply line to be loose at the front of the
refrigerator for connecting to the refrigerator.
5. Connect the 7 ft (2.13 m) flexible codes approved water
supply line to the refrigerator.
NOTE: If the main water shutoff valve is behind the
refrigerator, a secondary water shutoff valve may be installed
in line with the water supply line at the front of the product.
12
A. Household water line
B. Nut (purchased)
C. Ferrule (purchased)
D. Coupling
E. Bulb
F. N u t
G. Refrigerator water tubing
6. Turn on the water supply valve and check all connections for
leaks.
Plug in Refrigerator
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
A B
A
B
Level and Align Refrigerator
1. Set control switch at top of cabinet to the OFF position.
2. Plug into a grounded 3 prong outlet.
Move Refrigerator to Final
Location
IMPORTANT: To avoid floor damage, make sure levelers are
raised (not touching floor) and refrigerator is on rollers before
moving.
1. Place top of cardboard carton or plywood under refrigerator.
Remove dolly.
2. Do not remove film or cover.
3. Move the refrigerator straight back and evenly into the
opening. Be sure that the refrigerator side trims are not
interfering with the door opening. Also, be sure that the water
tubing is not kinked and the power supply cord is on top of the
refrigerator.
IMPORTANT: All four leveling legs must contact the floor to
support and stabilize the full weight of refrigerator. Rollers are for
moving refrigerator and not for permanent support.
After moving the refrigerator to its final location:
1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to
extend the legs to the floor as shown. The rollers should be off
the floor.
A. Rear leveling bolt
B. Front leveling bolt
2. Adjust the leveling legs to level and align the refrigerator from
left to right and front to back so that the refrigerator is level
and aligned with the cabinetry. The cabinetry surface must be
plumb for the ideal fit of the refrigerator side trim.
13
3. Continue adjusting all of the leveling legs to raise the
BA
C
2" (5 cm)
D
¹⁄₄" (6 mm)
max.
A BC
AB C
refrigerator until the top is within at least 1" (2.54 cm) of the
top soffit.
NOTE: If an anti-tip board has been used, adjust the leveling
legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of
the bottom of the anti-tip board as shown. Do not crush the
compressor cover.
A. Center board
B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards
C. Attach to studs with six #8 x 3" (7.6 cm) screws
D. Compressor cover
¹⁄₄
" (6.35 mm) max. above refrigerator
IMPORTANT: Adjust in small increments to keep from
damaging the cabinet trim and causing problems with the
door alignment or top grille fit. To avoid damage to the cabinet
or leveling legs, do not apply more than 50 inch-pounds
(5.65 Nm) of torque to the leveling bolts. The leveling legs can
be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.
3. Remove the locking plate as shown.
4. Using a ¹⁄₂" open end wrench, turn the bushing located
underneath the bottom of the hinge.
■ Turn the bushing to the left to lower the door.
■ Turn the bushing to the right to raise the door.
5. After adjusting, check the doors to make sure they are even
across the top and bottom. If the doors are not even, continue
to turn the bushing to adjust the door height.
6. Replace the locking plate.
7. Turn the bushing slightly to align the hinge and locking plate
screw holes.
8. Replace the door stop screw or screws and tighten.
9. Recheck to make sure the doors are aligned and even.
Door Swing Adjustment
1. Check that the refrigerator door can open freely. If the door
opens too wide, remove the door stop screw or screws
(depending on your model) from the bottom hinge. See “Door
Height Adjustment” earlier in this section.
2. Hold the door open to a position that is less than 90°.
3. Replace the door stop screw or screws in the bottom hinge
and tighten.
Adjust Doors
Door Height Adjustment
Use the following steps to adjust the door height, up or down,
after the doors have been leveled.
1. Open the freezer or refrigerator door and locate the bottom
hinge.
2. Remove the door stop screw from the bottom side of the
hinge with a ³⁄₈" open end wrench.
A. Bushing
B. Door stop screw
C. Locking plate
A. 130°
B. 110°
C. 90°
14
Door-to-Door or Door-to-Refrigerator Trim
†®TORX is a registered trademark of Saturn Fasteners, Inc.
A
B
A
B
A
B
A
A
Adjustment
1. Loosen, but do not remove, the four Torx®† 27 flat-head
mounting screws and the two ¹⁄₄" hex-head mounting screws.
2. Adjust the top hinge of either door to align it with the other
door or the refrigerator trim.
®†
3. Tighten the four Torx
27 flat-head mounting screws to a
torque of approximately 100 inch-pounds (11.3 Nm) and
tighten the two ¹⁄₄" hex-head mounting screws.
A. Torx® 27 flat-head mounting screws
B.
¹⁄₄
" hex-head mounting screws
Install Side Panel
If the built-in area depth is 25" (63.5 cm) or more, the side panels
can be installed inside the side trim or attached to the outside of
the side trim.
IMPORTANT: Jenn-Air is not responsible for the removal or
addition of molding or decorative panels that would not allow
access to the refrigerator for service.
1. For the inside side trim piece, slide the front edge of the
routed side panel into the trim piece.
2. Nail the rear edge of the panel to the support board.
Install Base Grille
There are two pieces to the base grille to allow for a custom fit: the
base grille itself and the skirt. The skirt can be added to the base
grille in order to extend it all the way to the floor.
1. To see whether the skirt is needed, place the base grille into
position. Do not attach the base grille to the refrigerator.
Measure the distance between the bottom of the base grille
and the floor. The gap must be a minimum of ¹⁄₂" (1.27 cm) in
order to add the skirt.
NOTE: If the gap measures less than ¹⁄₂" (1.27 cm), skip
steps 3 and 4 of the instructions, and install the base grille
only.
2. Remove the film from the base grille.
3. Snap the skirt onto the base grille.
A. Base grille
B. Skirt
4. Trim the skirt by scoring the proper “V” groove with a utility
knife. Break the skirt at the score line.
A. “V” groove
5. Using the two screws, attach the base grille assembly to the
refrigerator as shown.
NOTE: Drive in the right side screw first.
A. Support board (mounted to back wall)
B. Cab side trim
A. Screws (2)
15
Loading...