Jenn-Air JS48PPDUDB00, JS42SEDUDB00, JS48PPDUDB01, JS48SEDUDB00, JS48SEDUDB01 Installation Manual

...

0 (0)

JENN-AIR® SIDE BY SIDE BUILT-IN REFRIGERATOR

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS JENN-AIR

RÉFRIGÉRATEUR ENCASTRÉ CÔTE À CÔTE JENN-AIR

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

MANUAL DE INSTALACIÓN

Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico, llame al:

1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En Canadá, llame al: 1-800-807-6777, o visite nuestro sitio de internet: www.jennair.ca.

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web à www.jennair.ca.

Table of Contents/Índice/Table des matières ......................................................................................2

W10151249B

INSTALLATION GUIDE

GUIDE D’INSTALLATION

TABLE OF CONTENTS

REFRIGERATOR SAFETY...........................................................................3

MODELS....................................................................................................... 4

INSTALLATION REQUIREMENTS ............................................................. 6

Tools and Parts......................................................................................... 6

Location Requirements............................................................................. 6

Electrical Requirements............................................................................7

Water Supply Requirements..................................................................... 8

Tipping Radius..........................................................................................8

Product Dimensions .................................................................................9

Door Swing Dimensions ......................................................................... 10

Overlay Series Door Panel & Cabinetry Clearance ................................ 11

Overlay Series Custom Panels and Handle Kits .................................... 13

Euro-Style and Pro-Style

Overlay Series Custom Side Panels.......................................................15

Custom Side Panels .................................... 15

ÍNDICE

SEGURIDAD DEL REFRIGERADOR........................................................24

MODELOS.................................................................................................. 25

REQUISITOS DE INSTALACIÓN ..............................................................27

Piezas y herramientas.............................................................................27

Requisitos de ubicación .........................................................................27

Requisitos eléctricos............................................................................... 28

Requisitos del suministro de agua .........................................................29

Arco de vuelco........................................................................................29

Medidas del producto.............................................................................30

Medidas de oscilación de las puertas.................................................... 31

Espacio para el panel de la puerta y

para los gabinetes de la serie Overlay ................................................... 32

Paneles a la medida y juegos de agarraderas de la serie Overlay ........34

Paneles laterales a la medida para las estilo europeo, y Pro-Style

Paneles laterales a la medida para la serie Overlay...............................36

.....36

INSTALLATION INSTRUCTIONS ............................................................. 16

Unpack the Refrigerator ......................................................................... 16

Reduce Tipping Radius .......................................................................... 16

Move the Refrigerator into House .......................................................... 17

Install Anti-Tip Boards ............................................................................ 17

Connect the Water Supply .....................................................................18

Plug in Refrigerator................................................................................. 19

Move Refrigerator to Final Location....................................................... 19

Level and Align Refrigerator ................................................................... 19

Install Overlay Series Custom Panels .................................................... 20

Adjust Doors ...........................................................................................21

Install Side Panel .................................................................................... 22

Install Base Grille .................................................................................... 22

Complete Installation.............................................................................. 23

Water System Preparation ..................................................................... 23

INSTRUCCIONES DE INSTALACIÓN...................................................... 37

Desempaque el refrigerador...................................................................37

Cómo reducir el arco de vuelco .............................................................38

Cómo hacer entrar el refrigerador en la casa ........................................ 38

Cómo instalar los tableros antivuelco ....................................................38

Conexión del suministro de agua...........................................................39

Cómo enchufar el refrigerador ............................................................... 40

Cómo mover el refrigerador a su ubicación final...................................40

Nivelación y alineamiento del refrigerador ............................................. 41

Cómo instalar los paneles a la medida para la serie Overlay ................ 41

Ajuste las puertas ...................................................................................43

Cómo instalar el panel lateral ................................................................. 44

Cómo instalar la rejilla de la base...........................................................44

Cómo terminar la instalación..................................................................45

Preparación del sistema de agua...........................................................45

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ........................................................... 46

MODÈLES ..................................................................................................47

EXIGENCES D’INSTALLATION................................................................ 49

Outillage et pièces ..................................................................................49

Exigences d’emplacement .....................................................................49

Spécifications électriques ......................................................................50

Spécifications de l’alimentation en eau..................................................51

Rayon de basculement...........................................................................51

Dimensions du produit............................................................................ 52

Dimensions pour le pivotement des portes ........................................... 53

Série Overlay - Panneau de porte et placard -

dimensions et espace libre.....................................................................54

Panneaux personnalisés et poignées de la série Overlay......................56

Panneaux latéraux personnalisés des Euro-Syle, et Pro-Style

Panneaux latéraux personnalisés de la Série Overlay ...........................58

............58

INSTRUCTIONS D’INSTALLATION .........................................................59

Déballage du réfrigérateur......................................................................59

Réduction du rayon de basculement ..................................................... 60

Faire entrer le réfrigérateur dans le domicile.......................................... 60

Installation de planches antibasculement.............................................. 60

Raccordement à la canalisation d'eau...................................................61

Brancher le réfrigérateur......................................................................... 62

Déplacement du réfrigérateur à l'emplacement final............................. 62

Réglage de l'aplomb et alignement du réfrigérateur.............................. 63

Installation des panneaux personnalisés de la Série Overlay................ 63

Ajustement des portes............................................................................ 65

Installation du panneau latéral................................................................ 66

Installation de la grille de la base ...........................................................66

Achever l’installation............................................................................... 67

Préparation du système d’eau ............................................................... 67

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

follow instructions.

can be killed or seriously injured if you don't

You instructions.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

Non-Dispensing Refrigerators

MODELS

Euro-Style Design

Features stainless steel wrapped doors with towel bar handles. JS42SEFXDB JS48SEFXDB

Pro-Style® Design

Features stainless steel wrapped doors and Pro-Style® handles with diamond-etched grip.

JS42PPFXDB JS48PPFXDB

Overlay Design

Uses custom-made panels and custom hardware for a seamless appearance designed to blend with existing kitchen cabinetry.

JS42CXFXDB JS48CXFXDB

Dispensing Refrigerators

Euro-Style Design

Features stainless steel wrapped doors with towel bar handles. JS42SEDUDB JS48SEDUDB

Pro-Style® Design

Features stainless steel wrapped doors and Pro-Style® handles with diamond-etched grip.

JS42PPDUDB JS48PPDUDB

Overlay Design

Uses custom-made panels and custom hardware for a seamless appearance designed to blend with existing kitchen cabinetry.

JS42CXDBDB JS42CXDUDB JS48CXDBDB JS48CXDUDB

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Installer: Leave Installation Instructions with the homeowner.

■ Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local electrical inspector’s use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Cordless drill

■ Drill bits

■ Two adjustable

wrenches

■ Phillips screwdriver

■ Small level

■ Appliance dolly

■ To rx

■ ¹¹⁄₃₂" nut driver

■ ³⁄₈" and ¹⁄₂" open-end wrenches

■ ⁵⁄₃₂" Allen wrench

■ ¹⁄₄" and ⁵⁄₁₆" socket drivers

■ Tape m e a s u r e

■ Utility knife

PARTS NEEDED:

■ Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

■ One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

■ Overlay Series: Make custom panels, or consult a qualified

cabinetmaker or carpenter to make the panels. See “Overlay Series Custom Panels” for more information.

Pro-Style

■ If you are connecting the water line directly to copper tubing

and Euro-Style Series are shipped complete.

and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting.

®†

T27 screwdriver

Location Requirements

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

■ Observe all governing codes and ordinances.

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

■ Do not install in a location where the temperature will fall

below 55°F (13°C).

■ Floor must support the refrigerator weight, more than 600 lbs

(272 kg), door panels and contents of the refrigerator.

■ Ceiling height must allow for side tipping radius. See “Tipping

Radius.”

■ Location should permit door to open fully. See “Door Swing

Dimensions.”

■ Location must permit top grille removal. See “Opening

Dimensions.”

†®TORX is a registered trademark of Textron Innovations Inc.

Opening Dimensions

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the floor. See “Install Anti-Tip Boards” for more information.

NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained above the top grille in order for the top grille to be removed.

¹⁄₂"

(1.3 cm)

■ A grounded 3 prong electrical outlet should be placed within

4" (10.2 cm) of the right side cabinets or end panel. See “Electrical Requirements” for more information.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See “Water Supply Requirements” for more information.

80" - 90"

(203-229 cm)

(10.2 cm)

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

83¹⁄₂" (212.1 cm) min.

³⁄₄" (215 cm) max.

84 to bottom of solid soffit

77" (196 cm)

Width

(see chart following)

(15.2 cm)

(60.96 cm) min.

(2.54 cm)

24"

Model Width A (as shown above)

42 48

41¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm) 47¹⁄₂" (120.7 cm) to 47³⁄₄" (121.3 cm)

(15.2 cm)

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker box.

When you are finished, turn ON the master power switch or reconnect power at the circuit breaker box. Then reset the control to the desired setting.

NOTE: Flooring under refrigerator must be at same level as the room. Face of cabinetry must be plumb.

Water Supply Requirements

■ All installations must meet local plumbing code requirements.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. The right-hand side is recommended. The access hole through the cabinet must be within ¹⁄₂" (12.7 mm) of the rear wall.

NOTE: If the water shut off valve is in the back wall behind the refrigerator, it must be at an angle so that the tube is not kinked when the refrigerator is pushed into its final position.

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

(15.2 cm)

■ If the water shutoff valve is not in the cabinets, the plumbing

24"

(60.96 cm) min.

(2.54 cm)

(15.2 cm)

for the water line can come through the floor. A ¹⁄₂" (12.7 mm) hole for plumbing should be drilled at least 6" (15.2 cm) from the right or left hand side cabinet or panel. On the floor, the hole should be no more than 1" (2.54 cm) away from the back wall. See “Connect the Water Supply.”

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs more easily. NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

■ The dolly wheel height must be added to the tipping radius

when a dolly is used.

■ If needed, the tipping radius can be reduced. See “Reduce

Tipping Radius.”

Side Tipping Radius

The side tipping radius varies depending upon the width of the model. Use the chart provided to determine the side tipping radius.

NOTE: Tip on side only.

Model Tipping Radius A

42 48

93" (236.2 cm) 96" (243.8 cm)

Product Dimensions

Side View

■ The depth from the front of the top grille to the back of the

refrigerator cabinet is 25³⁄₈" (64.5 cm) for Euro and Pro styles. The Overlay style depth is 25¹⁄₈" (63.8 cm) without custom panels.

■ The power cord is 84" (213 cm) long.

■ The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

Euro-Style and Pro-Style®

25³⁄₈"

(64.5 cm)

³⁄₈"

(9.53 mm)

Overlay Style

25¹⁄₈"

(63.8 cm)

*83³⁄₈"

(211.8 cm)

84" (213.4 cm) Power Cord

*83³⁄₈"

(211.8 cm)

84" (213.4 cm) Power Cord

¹⁄₂" (8.9 cm)

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

¹⁄₂" (8.9 cm)

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Top Vi e w

Euro-Style and Pro-Style

24¹⁄₈"

(61.3 cm)

23¹¹⁄₁₆"

(60.3 cm)

(59.7 cm)

Model A B 42 Euro-Style 41" (104.1 cm) 2¹⁄₈" (5.3 cm) 48 Euro-Style 47" (119.4 cm) 2¹⁄₈" (5.3 cm) 42 Pro-Style 48 Pro-Style

¹⁄₂"

41" (104.1 cm) 2¹¹/₁₆" (6.74 cm)

47" (119.4 cm) 2¹¹/₁₆" (6.74 cm)

Overlay Style

)

(

23¹¹⁄₁₆"

(60.16 cm)

Door Swing Dimensions

The location must permit both doors to open to a minimum of 90°. Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended handles on a Classic model.

To adjust the door swing, see “Adjust Doors.”

42" (106.7 cm) Models

Model Width A

42 41" (104.1 cm) 48 47" (119.4 cm)

Front View

■ Width dimensions were measured from trim edge to trim

edge.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

*83³⁄₈" (211.8 cm)

¹⁄₄"

(94.6 cm)

³⁄₈"

105.1 cm)

90˚

110˚

130˚

Model A B

Pro-Style

10³/₄" (27.11 cm) 14¹/₄" (36.11 cm)

Euro-Style 10¹/₄" (25.87 cm) 13³/₄" (34.88 cm)

48" (121.9 cm) Models

39"

(99.1 cm)

⁷⁄₈"

111.4 cm)

41¹⁄₂"

(105.4 cm)

47⁷⁄₈"

(121.6 cm

90˚

110˚

130˚

44"

(111.8 cm)

51³⁄₈"

(130.5 cm)

(see chart following)

Model Width A (Trim edge to trim edge)

42 42¹⁄₄" (107.3 cm) 48 48¹⁄₄" (122.6 cm)

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

90˚

110˚

130˚

90˚

110˚

130˚

Model A B

Pro-Style

12³/₁₆" (30.84 cm) 16¹/₄" (41.16 cm)

Euro-Style 11⁵/₈" (29.43 cm) 15¹¹/₁₆" (39.75 cm)

Overlay Series Door Panel & Cabinetry Clearance

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If the refrigerator is to be installed close to the wall, see “Door Swing 90°” on next page.

Door Swing 110˚ Actual Size

Refrigerator to Cabinetry Clearance

Refrigerator Side Trim

/2"

(3.8 cm)

/4"

(3.2 cm)

(2.5 cm)

Cabinetry

/4" (6.35 mm)

Hinge

/2" (1.3 cm)

/4" (1.9 cm)

NOTE: For Overlay Series models, rout the hinge side of the custom door panels to a radius that is equal to at least half the thickness of the panel if a 130˚ door swing is desired. See “Adjust Doors.”

Door

/2"

(1.3 cm)

Backer Panel

/4"

(1.9 cm)

Overlay Panel

(2.5 cm)

Spacer Panel

1" (2.5 cm)

NOTE: Allow ¹⁄₂" (1.3 cm) clearance between overlay panel and cabinetry.

/4"

1 (3.2 cm)

/2"

1 (3.8 cm)

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

90˚ Door

Stop Position

Hinge

Door Swing 90˚ Actual Size

Refrigerator to Cabinetry Clearance

Refrigerator Side Trim

/4"

(1.9 cm)

/2"

(1.3 cm)

Cabinetry

(2.5 cm)

/4" (6.35 mm)

/2" (1.3 cm)

/4" (1.9 cm)

1" (2.5 cm)

/2"

(1.3 cm)

/4"

(1.9 cm)

(2.5 cm)

Door

Backer Panel

Overlay Panel

/4"

(3.2 cm)

/2"

(3.8 cm)

Spacer Panel

Allow a minimum of 4¹⁄₂" (11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if thicker custom panels or custom handles are used. Do not overlook baseboards.

Overlay Series Custom Panels and Handle Kits

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen décor, and to use custom handles for additional design flexibility.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and a ¹/₄" (6.35 mm) backer panel.

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

IMPORTANT:

■ The weight of the refrigerator door overlay panel cannot

exceed 50 lbs (23 kg).

■ The weight of the freezer door overlay panel cannot exceed

40 lbs (18.1 kg).

■ The weight of the top grille overlay panel cannot exceed

10 lbs (4.5 kg).

To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and sides edges of the backer panel. If you use spacer strips, it is also recommended that you use two 2" (5.08 cm) strips horizontally centered for added support.

Overlay Panel

Spacer Panel

/8"

(3.18 mm)

Overlay Panel

Decorative Overlay Panel

(18.4 cm)

Freezer

⁷⁄₈"

Door Panel

(Dispenser)

⁷⁄₈"

(27.6 cm)

Dispenser cut-out is centered left-to-right

(183.5 cm)

Preferred

Radius

¹⁄₂"

(1.27 cm)

14¹⁄₄"

(36.2 cm)

(86.0 cm)

¹⁄₄"

Door Panel

(Non-Dispenser)

Freezer

Refrigerator

Door Panel

/8" to 3/4"

(15.88 to

19.05 mm)

/8"

(3.18 mm)

Backer Panel

/4"

(6.35 mm)

Backer Panel

1" minimum (2.54 cm)

Offset Dimension

Door/Grille Trim

Model A B C 42 17¹/₄" (43.82 cm) 23¹/₄" (59.06 cm) 40³/₄" (103.51 cm) 48 19³/₄" (50.17 cm) 26³/₄" (67.95 cm) 46³/₄" (118.75 cm)

*Represents placement of dispenser frame.

Backer Panels

Dispenser Frame (dispenser models only)

NOTES:

■ Dashed lines represent backer panel placement.

■ Illustration shows backer panels placed on decorative

overlays.

³⁄₁₆"

Top Offset 1

22" (55.9 cm)

(15.7 cm)

⁵⁄₈" (4.13 cm)

70¹⁄₂" (179.1 cm)

Bottom Offset

¹⁄₂" (1.27 cm)

Handle-

Side Offset

¹⁄₄"

(6.4 mm)

70 (179.1 cm)

Side Offset

¹⁄₂" (12.7 mm)

¹⁄₂"

The dispenser frame attaches to the panel with 4 screws.

¹⁄₄"

33 (84.5 cm)

DED

Bottom Offset

¹⁄₈" (3.2 mm)

Bottom Offset

¹⁄₈" (3.2 mm)

Model D E F 42 16³/₄" (42.55 cm) 22³/₄" (57.79 cm) 39³/₄" (100.97 cm) 48 19¹/₄" (48.90 cm) 26¹/₄" (66.68 cm) 45³/₄" (116.21 cm)

A. Decorative panel B. Refrigerator door C. Dispenser frame

The dispenser frame overlaps the dispenser cutout by ⁵⁄₁₆" (0.78 cm) on each side and ¹⁄₂" (1.27 cm) on the top and bottom.

A A

¹⁄₂

" (1.27 cm) Overlap

Euro-Style and Pro-Style®

Custom Side Panels

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions and

may not reflect the needed panel installation dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

24¹⁄₈"

(61.3 cm)

23¹¹⁄₁₆"

(60.3 cm)

¹⁄₂"

(59.7 cm)

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Attach the support board with a screw or adhesive that is

compatible with aluminum and wood.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Route the front edge of the support board or attach a ¹⁄₄"

(6.35 mm) board to hold the panel in the cabinet side trim.

Side Trim

¹⁄₄"

(6.35 mm)

¹¹⁄₆₄"

(4.5 mm)

³⁄₁₆"

(4.7 mm)

⁷⁄₃₂"

(5.5 mm)

¹³⁄₃₂" (10 mm)

⁵⁄₈"

(15.7 mm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than ¹⁄₄" (6.35 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Overlay Series Custom Side Panels

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions and

may not reflect the needed installation dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on rear wall.

Refrigerator

Overlay

23¹¹⁄₁₆"

(60.16 cm)

Side Trim

³⁄₁₆"

³⁄₈"

(9.7 mm)

¹⁄₁₆"

(1.5 mm)

³⁄₃₂"

(2.38 mm)

(4.5 mm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than ³⁄₈" (9.5 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a ³⁄₈"

(9.5 mm) board to hold the panel in the cabinet side trim.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

■ Do not remove the protective film until the refrigerator is in its

operating position.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

■ Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating position.

1. Remove and save the literature package bag taped to the side

of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

2. If necessary, reduce the tipping radius. See “Tipping Radius”

for ceiling height requirements or “Reduce Tipping Radius” for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to “Move the Refrigerator into House.”

Reduce Tipping Radius

(if required)

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius” in the “Installation Requirements” section for more information.

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

42 88¹⁄₂" (224.8 cm) 48 89¹⁄₄" (226.7 cm)

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the

grille on a soft surface.

B BA

A. Top grille B. Cabinet side trim

3. Remove the six screws attaching each cabinet side trim to the

refrigerator and remove the side trims.

Move the Refrigerator into House

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5. Do not remove protective film or cover.

6. Reassemble the trim and top grille after the dolly has been

removed from the refrigerator.

Install Anti-Tip Boards

IMPORTANT:

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

■ It is recommended that board(s) be installed before the

refrigerator is installed.

■ Board(s) must be long enough to fully cover the width of the

compressor cover.

■ Locate the board(s) so the bottom surface(s) of the board(s)

is(are) 84" (213 cm) from the floor.

■ During installation, raise the refrigerator up so there is ¹⁄₄"

(6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to

229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1½" (3.8 cm). The board(s) must overlap the compressor cover.

1. Place an appliance dolly under the left side of the refrigerator

as shown. Be sure to protect the side trims and handles. Place the corner posts from the packing materials over the trims and handles as appropriate. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the Architect

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator

Series.

close to the built-in opening.

2" (5 cm)

A. Center board B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

¹⁄₄

" (6.35 mm) max. above refrigerator

Connect the Water Supply

A B

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Style 1 - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see

“Style 2 - Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply. IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the shutoff valve as shown.

A. Bulb B. Nut C. Water tubing

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. Plug in the refrigerator or reconnect power.

7. Flush the water system. See “Water System Preparation.” NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill ice container.

Style 2 - Copper Line Connection

Connecting to Water Line

NOTE: If existing water line meets the “Water System

Requirements,” see “Connecting to Refrigerator.”

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

DEF

A. Cold water pipe

B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve F. S h u to f f v a l v e

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

8. Turn off the shutoff valve on the water pipe. Coil the copper

tubing.

9. Check for leaks around the saddle valve.

Connecting to Refrigerator

1. Unplug the refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Remove the short, black plastic tube from the end of the water

line inlet. This tube protects the fitting during shipping only.

4. Measure the distance from the shutoff valve to the opening in

which the refrigerator will be located. Tubing must be extended from the shutoff valve into the refrigerator opening following specific guidelines. See “Water Supply Requirements.”

5. A ¹⁄₄" x ¹⁄₄" (6.35 mm to 6.35 mm) coupling is needed in order

to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

A B C D E F G

A. Water tubing B. Nut

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased) F. N ut (p u r c h a s ed )

G. Household water line (as

connected in previous section)

6. Turn shutoff valve ON.

A B

7. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

8. Plug in the refrigerator or reconnect power.

9. Flush the water system. See “Water System Preparation.” NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill ice container.

Plug in Refrigerator

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Level and Align Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to

extend the legs to the floor as shown. The rollers should be off the floor.

1. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

Move Refrigerator to Final Location

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1. Place top of cardboard carton or plywood under refrigerator.

Remove dolly.

2. Do not remove protective film or cover.

3. Move the refrigerator straight back and evenly into the

opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

A B

A. Rear leveling bolt B. Front leveling bolt

2. Adjust the leveling legs to level and align the refrigerator from

left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

3. Continue adjusting all of the leveling legs to raise the

refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

¹⁄₄" (6 mm)

max.

2" (5 cm)

A. Center board B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

¹⁄₄

" (6.35 mm) max. above refrigerator

3. Remove the handle side and top trims.

A. Trims

4. Slide the custom panels into the bottom and hinge side trims

on the refrigerator compartment and freezer compartment doors, making sure that the backer panel fits into the hinge side trims.

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.

4. For Classic and Overlay models, additional adjustments may

be needed after the custom panels are installed.

Install Overlay Series Custom Panels

IMPORTANT:

■ Install the custom handles prior to installing the panels on the

refrigerator. For more information on Jenn-Air custom handle selection, refer to the Jenn-Air Catalog, visit

www.jennair.com, or call 1-800-JENNAIR (1-800-536-6247). In Canada, visit www.jennair.ca, or call 1-800-807-6777.

■ Create custom door overlay panels according to the

specifications in the “Overlay Series Custom Panels” section.

■ Jenn-Air not responsible for the removal or addition of

molding or decorative panels that would not allow access to the refrigerator for service.

Door Panel Installation

1. Remove all tape and door bracing from the refrigerator and

freezer doors.

2. Open the refrigerator and freezer compartment doors.

A. Panels

5. Reinstall the handle-side and top trims.

6. Remove the protective skin from the screw covers. Slide or

snap the screw covers into the handle trim section.

7. Check refrigerator level and alignment. Adjust if needed.

Top Grille Panel

1. Grasp both ends of the top grille.

2. Push straight up, then pull straight out. Place the top grille

panel-side down on a soft working surface.

B BA

A. Top grille B. Cabinet side trim

3. Remove one end cap by loosening the nuts and sliding off the

end cap.

Adjust Doors

Door Height Adjustment

Use the following steps to adjust the door height, up or down, after the doors have been leveled.

1. Open the freezer or refrigerator door. Locate the bottom hinge

and remove the door stop screw.

Euro-Style and Pro-Style

Remove the door stop screw from the bottom side of the hinge with a ³⁄₈" open end wrench.

Styles

A. Bottom rail B. Nuts

C. End cap D. Top rail

4. Slide the backer panel into the top grille channel and reattach

the end cap.

A. Backer panel

5. Replace the top grille in the cabinet side trims and pull the

panel down slightly to lock it into place.

B BA

A BC

A. Bushing B. Door stop screw C. Locking plate

Overlay Style

Remove the two door stop screws: one from the bottom side using a ³⁄₈" open end wrench and one from the top side using a ⁵⁄₃₂" Allen wrench.

A. Door stop screw from bottom B. Door stop screw from top (110°)

2. Remove the locking plate as shown.

A. Top grille B. Cabinet side trim

+ 47 hidden pages