Jenn-Air JRC120012A User Manual
JENN-AIR® DETAILED PLANNING DIMENSIONS
A
A
B
B
I
J
E
36" Jx3™ GAS DOwNDRAfT COOkTOP
JGD3536W – 36" x 183⁄8" x 211⁄2"
PRODUCT DIMENSIONS
MODEL # JGD3536W
Overall width 36 91.4
A
Overall depth 21
B
B
TOp VIEW
Width of recessed cooktop 34
C
Width of blower motor assembly 12
D
Height from blower motor to countertop 18
E
Height of recessed cooktop 4 10.2
F
Height with grates 1
G
Height from gas inlet to countertop 7
H
Depth of recessed cooktop 19
I
Height from plenum to countertop 16
J
1 of 4
in cm
1
⁄2 54.6
1
⁄2 87.7
1
⁄2 31.8
3
⁄8 46.8
3
⁄8 3.4
3
⁄4 19.8
3
/4 50.0
7
⁄8 42.8
E
FRONT VIEW
A
C
G
F
H
D
B
I
J
E
SIDE VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120012A 07/2012
JENN-AIR® DETAILED PLANNING DIMENSIONS
E*
F
D
e
A
BB
v
H
G
C
I
L
BB
M
Side
Cabinet
36" Jx3™ GAS DOwNDRAfT COOkTOP
JGD3536W – 36" x 183⁄8" x 211⁄2"
2 of 4
OPENING/CLEARANCE DIMENSIONS
OPENING/CLEARANCE DIMENSIONS
MODEL # JGD3536W
A
B
C
A
D
E*
E*
F
F
G
H
I
H
G
v
C
I
e
D
J**
K
L
M
N
O
p
e
g
v
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet
is covered by not less than
less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
**Based on installation in a 24" (61.0 cm) base cabinet.
FRONT VIEW
J**
v
C
K
GAS REQUIREMENTS
Natural Gas
This cooktop is factory-set for use with natural gas.
Lp Gas Conversion
Conversion must be done by a qualified service technician. To convert
to LP gas, use the LP gas conversion kit provided with the cooktop.
ELECTRICAL REQUIREMENTS
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required.
A time-delay fuse or dedicated circuit is recommended.
VENTING REQUIREMENTS
This cooktop must be exhausted outdoors unless using the duct-free filter
Side
Cabinet
L
M
kit (JDA7000WX). Refer to kit instructions for further information.
LOCATION REQUIREMENTS
• To ensure cooktop base clearance, cabinet side walls need to be wider
than the cutout.
• A minimum clearance of 2" (5.1 cm) is recommended between the
blower motor and cabinet for proper cooling. A 6" (15.2 cm) clearance
is recommended for servicing access.
• An under counter built-in oven cannot be installed under this cooktop.
N
in cm
Width of combustible area above
cooking surface (min.)
Width from cooktop to fixed wall
or other combustible material (min.)
Width to center of vent opening option 17
36 91.4
6 15.2
1
⁄2 44.4
Width to outer edge of outlet 10 25.4
Height to bottom of uncovered wood or
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
or metal cabinet (min.)
30 76.2
18 45.7
Height to center of vent opening option 16 40.6
Height to top edge of outlet (min.) 12 30.5
Height to top of gas installation area 6 15.2
Depth to center of vent opening option 17
1
⁄8 43.5
Depth of gas installation area 6 15.2
Depth of upper cabinet (recommended) 13 33.0
Depth from cutout to wall (min.) 2 5.1
3
Width of cutout 34
⁄4 88.3
Depth of cutout 20 50.6
1
Depth from cutout to front of countertop 2
⁄8 5.4
Recommended electrical access location
Recommended gas supply line location
Recommended venting location –
see pages 3-4 for ducting information
1
⁄4" (0.6 cm) flame retardant millboard covered with not
M
O
P
SIDE VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
TOp VIEW – CUTOUT
JRC120012A 07/2012
Loading...