Jenn-Air JMC3415ES Installation Manual
INSTALLATION INSTRUCTIONS
BUILT-IN MICROWAVE OVEN KIT
INSTRUCTIONS D’INSTALLATION
ENSEMBLE FOUR À MICRO-ONDES
ENCASTRÉ
This product is suitable for use above electric built-in ovens or warming drawers. This product is not suitable for use below cooktops.
This Built-In Kit is designed for use with Jenn-Air Microwave Oven model specifying JMC3415ES Built-In Kit on the serial tag on the
front of the microwave oven.
These Installation Instructions cover different models. The appearance of your particular model may differ slightly from the illustrations
in these Installation Instructions.
Please read these instructions thoroughly before beginning installation.
Ce produit est conçu pour être installé au-dessus d’un four électrique encastré ou d’un tiroir-réchaud. Ce produit n’est pas conçu
pour être installé sous une table de cuisson. L’ensemble four à micro-ondes encastré est conçu pour être utilisé avec les modèles
de fours à micro-ondes Jenn-Air dont la plaque avant avec numéro de série indique le numéro d’ensemble encastré JMC3415ES.
Ces instructions d’installation couvrent plusieurs modèles. L’apparence de votre modèle peut différer légèrement des illustrations
présentes dans ce manuel.
Lire ces instructions attentivement avant de commencer l’installation.
Table of Contents/Table des matières
BUILT-IN MICROWAVE OVEN SAFETY ........................................2
INSTALLATION REQUIREMENTS .................................................2
Tools and Parts .............................................................................2
Location Requirements ................................................................3
Minimum Dimensions...................................................................3
Product Dimensions .....................................................................5
Electrical Requirements ...............................................................5
INSTALLATION INSTRUCTIONS ...................................................6
Install Rear and Top Ducts ...........................................................6
Install Rails and Bottom Duct ......................................................7
Install Microwave Oven and Trim Kit Frame ................................8
Complete Installation ...................................................................9
To Remove Trim Kit Frame ...........................................................9
ASSISTANCE ..................................................................................9
SÉCURITÉ DU FOUR À MICRO-ONDES ENCASTRÉ ..............10
EXIGENCES D’INSTALLATION ...................................................10
Outils et pièces ...........................................................................10
Exigences d’emplacement .........................................................11
Dimensions minimales ...............................................................11
Dimensions du produit ...............................................................13
Spécifications électriques ..........................................................13
INSTRUCTIONS D’INSTALLATION .............................................14
Installer les conduits arrière et supérieur ...................................14
Installer les rails et le conduit inférieur .......................................15
Installer le four à micro-ondes et le cadre
de la trousse de garniture ..........................................................16
Terminer l’installation ..................................................................17
Enlever le cadre de la trousse de garniture ...............................17
ASSISTANCE ................................................................................17
IMPORTANT:
Save for local electrical inspector’s use.
IMPORTANT :
À conserver pour consultation par l’inspecteur
local des installations électriques.
W10781779A
NOTE: Do not remove protective film from trim kit frame before
installing ducts and other mounting hardware. Only remove film
just before installing trim on cabinet.
REMARQUE : Ne pas retirer le film de protection du cadre de
la trousse de garniture avant l’installation des conduits et de la
quincaillerie de fixation. Enlever le film juste avant l’installation
du cadre sur le placard.
BUILT-IN MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting
installation. Read and follow the instructions provided
with any tools listed here.
Tools Needed
■ Phillips #2 screwdriver
■ Measuring tape
■ Combination square/straight edge
■ Pencil
■ Drill (for wall cabinet installations)
■■ Z\zn" (0.16 cm) drill bit (for wall cabinet installations)
■ 6" (15.2 cm) level
Parts Supplied
Check that all parts are included.
#8-14 x Z\x" screws (20)
NOTE: #8-14 x Z\x" screws will come in 2 separate packages.
#10-C\v" x B\zn" self-drilling screw (2)
Duct 3 (1)
Duct 5 (1)
Bottom Duct (1)
Duct 4 (1)
Mounting Rails (2)
Bottom Duct Attachment
Bracket (2)
Shims (1 pack)
Trim Kit Frame (1)
Duct 1 (1)
2
Duct 2 (1)
Location Requirements
The microwave oven may be located in a cabinet and/or above
a built-in oven or warming drawer. Check the opening where
the microwave oven will be installed. The bottom surface of the
cutout must be a minimum of 36" (91.4 cm) above the floor.
The location must provide:
■ Wood cabinetry.
■ Cutout opening that is plumb and square. See “Minimum
Installation Clearances” in the “Minimum Dimensions” section.
■ Cutout floor that is solid, level, and flush with bottom of
cabinet cutout.
■ Support for weight of at least 150 lbs (68 kg) which includes
microwave oven and items placed inside.
■ Grounded electrical outlet. See the “Electrical Requirements”
section.
■ Minimum installation clearances for installation location.
See the “Minimum Dimensions” section.
■ Complete enclosure around the recessed portion
of the microwave oven, including a solid, full ceiling.
■ A level floor – front to back and left to right.
Minimum Dimensions
Minimum Installation Clearances
For proper installation, the following minimum clearances must exist above and below the cutout opening.
Above Cabinet/Storage Drawer Installation Above Oven/Warming Drawer Installation
1"
1"
(25 mm)
(25 mm)
A
A
1"
1"
(25 mm)
(25 mm)
11⁄2"
1
Z\x"
(38 mm)
(38 mm)
A. Upper cabinet
B. Lower cabinet or storage drawer
C. Lower oven or warming drawer
B
B
C
C
NOTE: The bottom surface of the cutout must be a minimum of 36" (91.4 cm) above the floor.
3"
3"
(76 mm)
(76 mm)
3
Cabinet Requirements
C
E
Not Flush
B
DIMENSION 27" (68.6 CM)
INSTALLATION
Width
(Dimension A)
26Z\v" + Z\v", -0"
(66.7 cm + 1.3 cm,
-0 cm)
Height
(Dimension B)
Depth (Min.)
18ZC\zn" to 19Z\zn" (47.8 cm to 48.4 cm)
for all installations
21Z\x" (54.6 cm) with flush receptacle
A
E
D
30" (76.2 CM)
INSTALLATION
29Z\v" + Z\v", -0"
(74.3 + 1.3 cm,
-0 cm)
(Dimension C)
Minimum
clearance between
3" (7.6 cm) if installed over oven/warming
drawer
cutout openings
(Dimension D)
Face Frame
(Dimension E)
2" (5.08 cm) min. finished return flush
with opening edge on all 4 sides.
IMPORTANT: The oven support surface must be solid, level,
and flush with the bottom of the cabinet cutout. The floor
must be able to support the microwave oven weight.
Cutout Top View
21Z\x"
(54.6 cm)
Flush
NOTE: Cabinet sides must be perpendicular to cabinet floor.
A. Microwave oven
B. Flush receptacle
Recommended Outlet Location
8
Rear Wall of Cutout
4
Product Dimensions
A
B
C*
*Measurements include front facing of microwave oven.
DIMENSION 27" (68.6 CM)
Width
(Dimension A)
Height
(Dimension B)
Depth
(Dimension C)
INSTALLATION
24M\," (63.2 cm) 30" (76.2 cm)
14ZC\zn" (37.6 cm)
19Z\zn" (48.4 cm)
30" (76.2 CM)
INSTALLATION
Trim Kit Frame Dimensions
A
A
D
D
E
E
DIMENSION 27" (68.6 CM)
A 26C\v" (68.0 cm) 29C\v" (75.6 cm)
B 20Z\," (51.1 cm) 20Z\," (51.1 cm)
C 1Z\v" (3.2 cm) 1Z\v" (3.2 cm)
D 14M\zn" (36.7 cm) 14M\zn" (36.7 cm)
E 24C\v" (62.9 cm) 24C\v" (62.9 cm)
INSTALLATION
C
C
B
B
30" (76.2 CM)
INSTALLATION
Electrical Requirements
WARNING
Observe all governing codes and ordinances.
Required:
■ A 3 prong, polarized 115- to 120-volt, 60 Hz, AC-only,
15- or 20-amp electrical outlet at the rear of the opening.
Recommended:
■ A time-delay fuse or time-delay circuit breaker
■ A separate circuit serving only this microwave oven
GROUNDING INSTRUCTIONS
■
For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
SAVE THESE INSTRUCTIONS
5
INSTALLATION INSTRUCTIONS
WARNING
Excessive Weight Hazard
Use two or more people to move and install
microwave oven.
Failure to do so can result in back or other injury.
4. Position duct 3 on the top of the microwave oven, inserting
the edge of ducts 1 and 2 into duct 3. Secure duct 3 to ducts
1 and 2 using 2 #8-14 x Z\x" screws.
#8-14 x 1\x" screw
Ducts 1 and 2
Duct 3
IMPORTANT: To prevent damage, do not remove protective film
on the frame.
1. Empty microwave oven cavity of any loose contents,
including turntable.
2. Ensure floor of cabinet is level.
Install Rear and Top Ducts
1. Insert the edge of duct 1 into duct 2. Fasten together
with 1 #8-14 x Z\x" screw.
Duct 1
#8-14 x 1\x"
screw
2. Remove the 2 existing #8-18 x C\," screws at upper right
and left corners of the microwave oven.
#8-18 x 3⁄,"
screw
#8-18 x 3⁄,"
screw
Duct 2
#8-14 x 1\x"
screw
5. Position duct 4 on top of the microwave oven and
insert it into duct 3. Secure duct 4 to duct 3 using
2 #8-14 x Z\x" screws.
Duct 4
Duct 3
#8-14 x 1\x"
screw
#8-14 x 1\x"
screw
IMPORTANT: The double holes on duct 4 go toward
the back of the microwave oven. On each side of duct 4,
screw 1 #8-14 x Z\x" screw into the front-most hole
of the double hole.
3. Secure ducts 1 and 2 with #8-18 x C\," screws just removed
from the microwave oven.
#8-18 x 3⁄,"
screw
Duct 1
#8-18 x 3⁄,"
screw
Duct 2
6
Use hole closest to front
of microwave oven.
6. Position duct 5 on top of the microwave oven and insert
it into duct 4. Secure duct 5 using 3 #8-14 x Z\x" screws
provided.
#8-14 x 1\x" screw
#8-14 x 1\x"
screw
#8-14 x 1\x" screw
Duct 4
Duct 5
Loading...