How it Works
JennAir
Loading...
JMC2430IM
Installation Guide
16 pgs1.72 Mb0
Flush Kit Installation Guide
8 pgs724.19 Kb0
Owner's Manual
48 pgs1.74 Mb0
Parts List
12 pgs896.96 Kb0
Specs
2 pgs15.16 Kb0
Wiring Guide
1 pgs790.16 Kb0

JennAir JMC2430IM, JMC2427IM Installation Guide

INSTALLATION INSTRUCTIONS
27" (68.6 CM) AND 30" (76.2 CM) ELECTRIC BUILT-IN
CONVECTION MICROWAVE OVEN
INSTRUCTIONS D’INSTALLATION
FOUR À MICRO-ONDES ENCASTRÉ ÉLECTRIQUE À
CONVECTION DE 27" (68,6 CM) ET 30" (76,2 CM)
Table of Contents/Table des matières
Tools and Parts .............................................................................3
Location Requirements ................................................................3
Electrical Requirements ...............................................................4
Spacer Kit Installation ..................................................................5
Prepare Built-In Microwave Oven ................................................5
Make Electrical Connection .........................................................6
Install Microwave Oven ................................................................6
Complete Installation ...................................................................7
Outils et pièces .............................................................................8
Exigences d’emplacement ...........................................................8
Spécications électriques ..........................................................10
INSTRUCTIONS D’INSTALLATION .............................................11
Installation de la trousse d’entretoise ........................................11
Préparation du four à
micro-ondes encastré ................................................................11
Raccordement électrique ...........................................................11
Installation du four à micro-ondes .............................................12
Achever l’installation ..................................................................13
IMPORTANT:
Save for local electrical inspector’s use.
IMPORTANT:
À conserver pour consultation par l’inspecteur local des installations électriques.
W11235626A
BUILT-IN MICROWAVE OVEN SAFETY
2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Tools Needed
■ Phillips screwdriver
■ Flat-blade screwdriver
■ Measuring tape
■ Level
Parts Needed
■ UL listed or CSA approved conduit connector
■ UL listed wire connectors
Parts Needed – Flush Installation
■ W10801485 Stainless steel ush installation kit for
27" (68.6 cm) models
■ W10801486 Stainless steel ush installation kit for
30" (76.2 cm) models
■ W10801487 Black ush installation kit for
30" (76.2 cm) models
To order, see the “Assistance or Service” section of the Use and Care Guide.
■ Drill (for wall cabinet
installations)
■ 1/8" (3 mm) drill bit (for wall
cabinet installations)
■ 1" (2.5 cm) drill bit (for wall
cabinet installations
■ For installation above single built-in oven, the junction box
must located inside upper cabinet.
■ If you are installing the junction box on rear wall behind
the microwave oven, the junction box must be recessed and located in the upper or lower right or left corner of the cabinet; otherwise, the microwave oven will not t into the cabinet opening.
■ Microwave oven support surface must be solid, level, and
ush with bottom of cabinet cutout. Floor must be able to support a weight of 108 lbs (49.0 kg).
IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate, or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).
Product Dimensions
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
A
E
B
Parts Supplied
A
A. Spacer bars (2) B. Bottom vent (1) C. 3/8" (9.5 mm) hex-head washer screws (4) D. 3/4" (1.9 cm) pan-head screws (4)
Check local codes. Check existing electrical supply. See “Electrical Requirements.”
It is recommended that all electrical connections be made by a licensed, qualied electrical installer.
C
D
B
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■ Cabinet opening dimensions that are shown must be
used. Given dimensions provide minimum clearance with microwave oven.
■ Recessed installation area must provide complete enclosure
around the recessed portion of the microwave oven.
■ Grounded electrical supply is required. See “Electrical
Requirements” section.
■ Electrical supply junction box should be located 3" (7.6 cm)
maximum below the support surface when the microwave oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the left rear corner of the support surface to pass the appliance cable through to the junction box.
D
C
F
27" (68.6 cm) models
A. 253/8" (64.5 cm) B. 173/8" (44.1 cm) C. 2211/16" (57.7 cm) D. 263/4" (68.0 cm) overall width E. 197/8" (50.3 cm) overall height F. JMC2427IM: 259/16 (64.9 cm) JMC2427IL: 243/4" (62.9 cm)
30" (76.2 cm) models
A. 283/8" (72.1 cm) B. 173/8" (44.1 cm) C. 2211/16" (57.7 cm) D. 293/4" (75.6 cm) overall width E. 197/8" (50.3 cm) overall height F. JMC2430IM: 259/16 (64.9 cm) JMC2430IL: 243/4" (62.9 cm)
27" (68.6 cm) and 30" (76.2 cm) Microwave Oven Spacer Kit
A
27" (68.6 cm) models
A. 263/4" (67.9 cm) overall width
30" (76.2 cm) models
A. 293/4" (75.6 cm) overall width
NOTE: The microwave oven spacer kit will allow the microwave oven to be installed in a 173/8" to 173/4" (44.1 to 45.1 cm) maximum cutout height.
3
A microwave oven spacer kit is available from your dealer that will allow the microwave oven to be installed in a 19" to 19/16" (48.3 to 50.2 cm) maximum cutout height. Match the oven size to the following kits:
■ 27" (68.6 cm) Stainless Steel – Model W10469901
■ 30" (76.2 cm) Stainless Steel – Model W10469903
To order, see the “Assistance or Service” section of the Use and Care Guide.
Cabinet Dimensions
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
Installation Above Single Built-In Oven
A
2 3/16"
(5.5 cm)
A
D
F
G
B
E
C
27" (68.6 cm) models
A. 27" (68.6 cm) min. cabinet
width
B. 197/8" (50.3 cm) from bottom
of cutout to bottom of upper cabinet door
C. 40" (101.6 cm) bottom of
cutout to floor (recommended) D. 251/2" (64.8 cm) cutout width E. 11/2" (3.8 cm) min. bottom of
cutout to top of cabinet door F. 175/8" (44.7 cm) recommended
cutout height (will fit cutout
height from 173/8" [44.1 cm] to
173/4" [45.1 cm]) G. 217/8" (55.5 cm) min. cutout
depth
30" (76.2 cm) models
A. 30" (76.2 cm) min. cabinet
width
B. 197/8" (50.3 cm) from bottom
of cutout to bottom of upper cabinet door
C. 40" (101.6 cm) bottom of
cutout to floor (recommended) D. 281/2" (72.4 cm) cutout width E. 11/2" (3.8 cm) min. bottom of
cutout to top of cabinet door F. 175/8" (44.7 cm) recommended
cutout height (will fit cutout
height from 173/8" [44.1 cm] to
173/4" [45.1 cm]) G. 217/8" (55.5 cm) min. cutout
depth
Minimum Installation Clearances
For proper installation, the following minimum clearances must exist above and below the cabinet opening.
1"
(2.5 cm) from top of oven
B
A. Upper cabinet B. Lower single oven
Electrical Requirements
GROUNDING INSTRUCTIONS
For a permanently connected microwave oven:
The microwave oven must be connected to a grounded, metallic, permanent wiring system, or an equipment grounding conductor should be run with the circuit conductors and connected to the equipment grounding terminal or lead on the microwave oven.
SAVE THESE INSTRUCTIONS
If codes permit and a separate ground wire is used, it is recommended that a qualied electrical installer determine that the ground path and wire gauge are in accordance with local codes.
Check with a qualied electrical installer if you are not sure the oven is properly grounded.
This oven must be connected to a grounded metal, permanent wiring system.
Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70 – latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91 – latest edition, and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
Electrical Connection
To properly install your microwave oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
4
■ Microwave oven must be connected to the proper electrical
D
voltage and frequency as specied on the model/serial/rating plate. The model/serial/rating plate is located underneath the control panel along the oven vent.
A
A. Model/serial/rating plate
■ The microwave oven rated 120/240 V, 20 A, has
4 wires (L1, L2, N, and G) in the ex conduit, and should be connected to a 20 A maximum-rated circuit, overcurrent protected on both the L1 and L2 circuits.
■ A time-delay fuse or circuit breaker is recommended.
■ Flexible cable from the microwave oven should be
connected directly to the junction box.
INSTALLATION INSTRUCTIONS
■ Do not cut the conduit. The length of conduit provided is for
serviceability of the microwave oven.
■ A UL listed or CSA approved conduit connector must be
provided.
■ If the house has aluminum wiring, follow the procedure
below: Connect the aluminum wiring using special connectors
and/or tools designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer’s recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.
For power requirements, refer to the following table:
Voltage Microwave With Convection Oven
120/240 VAC 15 A 120/208 VAC 15 A
Spacer Kit Installation
NOTES:
■ The microwave oven spacer kit allows the microwave oven
to be installed in an 17 maximum cutout height.
■ If your cabinet cutout height is more than 17
you must install the spacer kit. Proceed to “Assemble Spacer Kit.”
■ If your cabinet cutout height is less than 17
you do not have to install the spacer kit. Proceed to “Prepare Built-In Microwave Oven.”
Assemble Spacer Kit
1. Attach the bottom vent to spacer bars using four 3/8" (9.5 mm)
NOTE: Spacer bar anges should be facing out.
Install Spacer Kit
1. Center assembled microwave oven spacer kit against lower front edge of the cabinet cutout.
2. Using an 1/8" (3.2 mm) drill bit, drill through the mounting holes in the spacer bars to create pilot holes.
hex-head washer screws.
B
A
A. Bottom vent B. Spacer bar flange C. Spacer bars D. 3/8" (9.5 mm) hex-head washer screws
7
/16" to 177/8" (44.1 cm to 45.3 cm)
7
/16" (44.1 cm),
7
/16" (44.1 cm),
C
D
3. Attach the assembled spacer kit to the cabinet using four 3/4" (1.9 cm)
( at-head screws. Do not overtighten screws.
A
B
A. 3/4" (1.9 cm) flat-head screws B. Spacer kit assembly
Prepare Built-In Microwave Oven
1. Locate existing wiring to avoid drilling into or severing wiring during installation.
WARNING
Excessive Weight Hazard
Use two or more people to move and install microwave oven.
Failure to do so can result in back or other injury.
2. To avoid oor damage, set the microwave oven onto cardboard prior to installation. Do not use handle or any portion of the front frame for lifting.
3. Remove the shipping materials and tape from the microwave oven.
4. Remove and set aside racks and other items from inside the microwave oven.
5. Remove the hardware package from inside the bag containing literature.
6. Move the microwave oven and cardboard close to the microwave oven’s nal location.
5
Loading...
+ 11 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use