JENN-AIR JMC2430BS, KBHS179BSS, KBHS109BSS, JMC2430BP, JMC2430BB Installation Instructions
INSTALLATION INSTRUCTIONS
27" (68.6 CM) AND 30" (76.2 CM) ELECTRIC BUILT-IN
CONVECTION MICROWAVE OVEN
INSTRUCTIONS D’INSTALLATION
FOUR À MICRO-ONDES ENCASTRÉ ÉLECTRIQUE
À CONVECTION DE 27" (68,6 CM) ET 30" (76,2 CM)
Table of Contents/Table des matières
BUILT-IN MICROWAVE OVEN SAFETY.......................................1
INSTALLATION REQUIREMENTS................................................2
Tools and Parts ............................................................................2
Location Requirements................................................................2
Electrical Requirements ...............................................................3
INSTALLATION INSTRUCTIONS..................................................4
Spacer Kit Installation ..................................................................4
Prepare Built-In Microwave Oven................................................4
Make Electrical Connection .........................................................5
Install Microwave Oven................................................................5
Complete Installation ...................................................................6
SÉCURITÉ DU FOUR À MICRO-ONDES ENCASTRÉ.................9
EXIGENCES D'INSTALLATION.....................................................9
Outils et pièces.............................................................................9
Exigences d’emplacement...........................................................9
Spécifications électriques ..........................................................11
INSTRUCTIONS D’INSTALLATION.............................................12
Installation de la trousse d'entretoise ........................................12
Préparation du four à micro-ondes encastré.............................12
Raccordement électrique...........................................................12
Installation du four à micro-ondes .............................................13
Achever l’installation ..................................................................14
BUILT-IN MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
W10351317A
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■ Phillips screwdriver
■ Flat-blade screwdriver
■ Measuring tape
■ Level
Parts needed
■ A UL listed or CSA approved conduit connector
■ UL listed wire connectors
■ Drill (for wall cabinet installations)
■ ¹⁄₈" (3 mm) drill bit (for wall
cabinet installations)
■ 1" (2.5 cm) drill bit (for wall
cabinet installations)
■ If you are installing the junction box on rear wall behind the
microwave oven, the junction box must be recessed and
located in the upper or lower right or left corner of the cabinet;
otherwise, the microwave oven will not fit into the cabinet
opening.
■ Microwave oven support surface must be solid, level and flush
with bottom of cabinet cutout. Floor must be able to support a
weight of 90 lbs (41.0 kg).
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).
Product Dimensions
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
Parts supplied
A
A. Spacer bars (2)
B. Bottom vent (1)
C.
³⁄₈
" hex washer head screws (4)
D. ¾" pan head screws (4)
Check local codes. Check existing electrical supply. See
“Electrical Requirements.”
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
C
D
B
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■ Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance with
microwave oven.
■ Recessed installation area must provide complete enclosure
around the recessed portion of the microwave oven.
■ Grounded electrical supply is required. See “Electrical
Requirements” section.
■ Electrical supply junction box should be located 3" (7.6 cm)
maximum below the support surface when the microwave
oven is installed in a wall cabinet. A 1" (2.5 cm) minimum
diameter hole should have been drilled in the left rear corner
of the support surface to pass the appliance cable through to
the junction box.
■ For installation above single built-in oven the junction box
must located inside upper cabinet.
A
B
E
C
30" (76.2 cm) models
A. 25
⁵⁄₈
" (72.7 cm) recessed width
B. 1
8⁵⁄₈
" (47.3 cm) overall height
C. 29
³⁄₄
" (75.6 cm) overall width
D. 22
³⁄₄
" (57.8 cm) overall depth
E. 17
¹⁄₄
" (43.8 cm) recessed height
27" (68.6 cm) models
A. 25
⁵⁄₈
" (65.1 cm) recessed width
B. 1
8⁵⁄₈
" (47.3 cm) overall height
C. 26
³⁄₄
" (68.0 cm) overall width
D. 22
³⁄₄
" (57.8 cm) overall depth
E. 17
¹⁄₄
" (43.8 cm) recessed height
D
27" (68.6 cm) and 30" (76.2 cm) Microwave Oven Spacer Kit
A
27" (68.6 cm) models
A. 26
³⁄₄
" (67.9 cm)
overall width
30" (76.2 cm) models
A. 29
³⁄₄
" (75.6 cm)
overall width
NOTE: The microwave oven spacer kit will allow the microwave
oven to be installed in a 17³⁄₈"-17³⁄₄" (44.1-45.1 cm) maximum
cutout height.
A microwave oven spacer kit is available from your dealer that will
allow the microwave oven to be installed in a 19"- 19¹³⁄₁₆"
(48.3-50.2 cm) maximum cutout height. Match the oven size to
the following kits:
27" (68.6 cm) Stainless Steel - Model W10469901
30" (76.2 cm) Stainless Steel - Model W10469903
To order, see the “Assistance or Service” section of the Use and
Care Guide.
2
Cabinet Dimensions
27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens
A
D
F
G
B
E
C
27" (68.6 cm) models
A. 27" (68.6 cm) min. cabinet
width
B. 18
⁵⁄₈
" (47.3cm) from bottom of
cutout to bottom of upper
cabinet door
C.
40
" (101.6 cm) bottom of
cutout to floor (recommended)
D. 25
¹⁄₂
" (64.8 cm) cutout width
E. 1
¹⁄₂
" (3.8 cm) min. bottom of
cutout to top of cabinet door
F. 1 7
⁵⁄₈
" (44.7 cm) recommended
cutout height (will fit cutout
height from 17
17
³⁄₄
" [45.1 cm])
G. 21
⁷⁄₈
" (55.5 cm) min. cutout
depth
³⁄₈
" [44.1 cm] to
30" (76.2 cm) models
A.
30
" (76.2 cm) min. cabinet
width
B. 18
⁵⁄₈
" (47.3cm) from bottom of
cutout to bottom of upper
cabinet door
C.
40
" (101.6 cm) bottom of
cutout to floor (recommended)
D. 28
¹⁄₂
" (72.4 cm) cutout width
E. 1
¹⁄₂
" (3.8 cm) min. bottom of
cutout to top of cabinet door
F. 1 7
⁵⁄₈
" (44.7 cm) recommended
cutout height (will fit cutout
height from 17
17
³⁄₄
" [45.1 cm])
G. 21
⁷⁄₈
" (55.5 cm) min. cutout
depth
³⁄₈
" [44.1 cm] to
Minimum Installation Clearances
For proper installation, the following minimum clearances must
exist above and below the cabinet opening.
Electrical Requirements
GROUNDING INSTRUCTIONS
For a permanently connected microwave oven:
The microwave oven must be connected to a grounded,
metallic, permanent wiring system, or an equipment
grounding conductor should be run with the circuit
conductors and connected to the equipment grounding
terminal or lead on the microwave oven.
SAVE THESE INSTRUCTIONS
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
codes.
Check with a qualified electrical installer if you are not sure the
microwave oven is properly grounded.
This microwave oven must be connected to a grounded metal,
permanent wiring system.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70-latest edition or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and
all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Electrical Connection
To properly install your microwave oven, you must determine the
type of electrical connection you will be using and follow the
instructions provided for it here.
■ Microwave oven must be connected to the proper electrical
voltage and frequency as specified on the model/serial
number rating plate. The model/serial number rating plate is
located underneath the control panel, along the oven vent.
Installation Above Single Built-In Oven
A
B
A. Upper cabinet
B. Lower single oven
Approved models: KEBK171B, KEBK101B, KEBS179B,
KEBS109B and KEBU109B.
1"
(2.5 cm)
1"
(2.5 cm)
from top
of oven
A
A. Model/serial number plate
■ The microwave oven rated 120/240 volt, 20-amp, has 4 wires
(L1, L2, N and G) in the flex conduit and should be connected
to a 20-amp maximum rated circuit, overcurrent protected on
both the L1 and L2 circuits.
■ A time-delay fuse or circuit breaker is recommended.
■ Flexible cable from the microwave oven should be connected
directly to the junction box.
■ Do not cut the conduit. The length of conduit provided is for
serviceability of the microwave oven.
■ A UL listed or CSA approved conduit connector must be
provided.
3
■ If the house has aluminum wiring follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
INSTALLATION INSTRUCTIONS
Spacer Kit Installation
NOTES:
■ The microwave oven spacer kit allows the microwave oven to
be installed in an 17⁷⁄₁₆" (44.1 cm) to 17⁷⁄₈" (45.3 cm)
maximum cutout height.
■ If your cabinet cutout height is more than 17⁷⁄₁₆" (44.1 cm),
you must install the spacer kit. Proceed to “Assemble Spacer
Kit.”
■ If your cabinet cutout height is less than 17⁷⁄₁₆" (44.1 cm), you
do not have to install the spacer kit. Proceed to “Prepare
Built-In Microwave Oven.”
Assemble Spacer Kit
For power requirements, refer to the following table.
Voltage Microwave Without
Convection Oven
120 VAC 1800 W 2140 W
120 VAC 15.0 A 19.9 A
3. Attach the assembled spacer kit to the cabinet using four
¾" flat head screws. Do not overtighten screws.
A
A. ¾" pan head screws
B. Spacer kit assembly
Microwave With
Convection Oven
B
1. Attach the bottom vent to spacer bars using four ³⁄₈" hex
washer head screws.
NOTE: Spacer bar flanges should be facing out.
D
B
A
C
D
A. Bottom vent
B. Spacer bar flange
C. Spacer bars
D.
³⁄₈
" hex washer head screws
Install Spacer Kit
1. Center assembled microwave oven spacer kit against lower
front edge of the cabinet cutout.
2. Using an ¹⁄₈" (0.32 cm) drill bit, drill through the mounting
holes in the spacer bars to create pilot holes.
Prepare Built-In Microwave Oven
1. Locate existing wiring to avoid drilling into or severing wiring
during installation.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
microwave oven.
Failure to do so can result in back or other injury.
2. To avoid floor damage, set the microwave oven onto
cardboard prior to installation. Do not use handle or any
portion of the front frame for lifting.
3. Remove the shipping materials and tape from the microwave
oven.
4. Remove and set aside racks and other items from inside the
microwave oven.
5. Remove the hardware package from inside the bag
containing literature.
6. Move the microwave oven and cardboard close to the
microwave oven’s final location.
4
Make Electrical Connection
H
G
3-Wire Cable with Ground from Home Power Supply to
Microwave Oven Cable with 4-Wires
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Use 12 gauge solid copper wire.
Electrically ground oven.
Failure to follow these instructions can result in death,
fire, or electrical shock.
This microwave oven is manufactured with a neutral (white)
power supply wire and a cabinet-connected green (or bare)
ground wire.
1. Disconnect power.
2. Feed the flexible cable conduit from the microwave oven
through the opening in the cabinet.
3. Remove junction box cover if it is present.
4. Install a UL listed or CSA approved conduit connector to the
junction box.
A
A
B
C
D
A. Cable from home power supply
B. Green (or bare) wires
C. White wires
D. 4-wire cable from microwave
oven
E. UL listed or CSA approved
conduit connector
1. Connect the 2 black wires (G) together using a UL listed wire
connector.
2. Connect the 2 white wires (C) using a UL listed wire
connector.
3. Connect the 2 red wires (F) together using a UL listed wire
connector.
4. Connect the 2 green (or bare) wires (B) together using a UL
listed wire connector.
5. Install junction box cover.
F. Re d w i re s
G. Black wires
H. UL listed wire connector
I. Junction box
I
F
E
A. UL listed or CSA approved conduit connector
5. Route the flexible cable conduit from the microwave oven to
the junction box through a UL listed or CSA approved conduit
connector.
6. Tighten screws on conduit connector.
7. Complete electrical connection.
Install Microwave Oven
1. Using 2 or more people, lift the microwave oven partially into
the cabinet cutout. If a spacer kit has been installed, lift the
microwave oven over it and position the microwave between
the guide strips.
C
C
A
B
A. Spacer bar flange
B. Spacer bar
C. Microwave oven
5
Loading...