Jenn-Air JJW7530DDB19, JJW7530DDS19, JJW7530DDW19 Installation Guide

Built-In 30"

,JENN-AIR

Electric Wall Ovens

,[oTd[e[e]0kVj=1011=10[=.]_vi'/,-!I IKe_'t=101

1 1/4" Dia,ConduitAccessHole*

5/8" PlywoodFloor (MustSupport200 Ibs,)

DIMENSIONS

inches cm

A 30 MIN 76,20 B 24 MIN 60,96

C 225/8 + 1/16 57,47 D 24 MIN 60,96

E 28 1/2+ 1/16 72,39 F 23 1/16 58,58 G 293/4 75,57

H 257/16 64,61 I 4to 37,5 10,2to 95,25

|vlrl_-!!l[olVt:l_LlJOl=]=l=t[o,[o]lJ_li=II

1 1/4" Dia,ConduitAccessHole*

5/8" PlywoodFloor (MustSupport200 Ibs,)

DIMENSIONS

inches cm

A 25 63,50 B 24 MIN 60,96

C 225/8 + 1/16 57,47 D 24 MIN 60,96

E 281/2 72,39 F 23 1/16 58,58

G 293/4 75,57 H 257/16 64,61

I 36 91,44 J 1 1/2 3,81

403 WEST FOURTH STREET, NORTH

NEWTON, IA 50208

CONVENIENCEWALL OVEN

'B-.._ =,i

UNDERCOUNTER WALL OVEN

NOTE:

AllJA Cooktops 24,13MAX

I_[e]i :[-']

Donot blockair exhaustslots alongbottomofoven.

Y Gasor electriccooktopsmay beinstalledoverovens, Seecooktopinstallation

instructionsfor cutoutsize,

W Electricalconnectionforelectriccooktopmustin adjacentaccessiblelocation.Cook

topandwall ovenmustbe on separate120/240or120/208volt 60Hz ACcircuits,

* Holemustbecutas closetocornerof cabinetas possible.

** Seedealerfor approvedcooktops.

8101 P485-60

(05-03-00)

Installing Bottom Trim Piece

Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, if

doubt exists as whether the appliance is properly grounded.

CAUTION

For European style cabinets (flush front) the required

clearance for operation of the oven door is minimum spacing of 718" between the cutout and the door, hinge or drawer of the cabinet.

Some built-in cabinets may not be wide enough, due to

their construction, to allow this installation.

Installation

1 Cut hole in cabinet to mount oven. Cutout in cabinet

should be level and straight. NOTE: There are no provisions to level the unit after it

is installed. An oven that is not level could cause poor baking results.

2. Install plywood floor as shown.

3. Remove oven door(s). See Oven Door Removal procedure.

4. Attach unit to the cabinet with four No. 8 x 1" screws supplied with unit inside of envelope containing these

instructions. Pre-drill holes in cabinet for attachment screws using 118"drill. Oven mounting holes are

provided in side trim.

5. Install bottom trim.

6. Replace oven door(s). See Oven Door Replacement procedure.

7. See instructions at right for electrical hook-up.

8. See Use and Care Manual for operating instructions.

Remove lower screws

from hinge receptacle

plates. Align lower trim and reinstall screws.

DO NOT INSTALL BOTTOM TRIM UNTIL UNIT IS ATTACHED TO THE CABINET.

Electrical Connections

Unit to be properly circuit protected and wired according to local electrical code and National Electrical Code.

It is advisable that the electrical wiring and hookup be accomplished by a competent electrician.

120/240 VAC or 120/208 VAC 60 Hz. See serial plate on

front of unit for power requirements. The neutral of this unit is grounded to the frame through

the green or solid grounding wire. (The green and the white wires are twisted together at the termination of the

conduit.) If used on new branch-circuit installations (1996 NEC), mobile homes, recreational vehicles, or in an area

where local codes prohibit grounding through the neutral conductor, untwist or disconnect the green wire and

connect the green wire to ground in accordance with local code. Connect the white neutral to the service neutral.

Connect all wires to the branch circuit with approved connectors. Use copper or aluminum wire. If aluminum wire is used, use connectors recognized for joining

aluminum to copper. The chart below recommends the minimum circuit

protection and wire size if the appliance is the only unit on the circuit.

RECOMMENDED MINIMUM

K.W. RATING CIRCUIT PROTECTION WIRE SIZE

ON SERIAL PLATE IN AMPERS (AWG)

0- 4.8 20 12

4.9- 6.9 30 10

7.0- 9.9 40 8

10.0 - 11.9 50 8

12.0 - 14.9 60 6

Service

Interrupt the source of electricity to the unit when attempting to repair or service the oven. Failure to do this

could result in a dangerous or even fatal shock.

IMPORTANT - SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE

Oven Door Removal

For ease of installation, remove oven door(s) before placing unit into cutout. This will reduce the weight of the unit by about 35 pounds per door. Remove oven door(s)

as follows:

• Open oven door to the "Full Open" position (see Figure 1).

• Rotate hinge locking lever DOWN, to unlock hinge

from the unit (see Figure 2).

• Close oven door to the "Removal" position (until it stops; see Figure 3).

• Grasp the door firmly on each side and lift the door straight up and off the unit.

NOTE: The oven door is heavy. Be sure you have a firm grip before lifting the oven door off the unit.

Do not lift the door by the handle!

Oven Door Replacement

Replace oven door(s) after placing unit into cutout. Replace oven door(s) as follows:

• Grasp oven door firmly on each side, hold oven door at approximately a 30° angle and align oven door

hinge arm (see Figure 4) with hinge receiver on unit (see Figure 5).

• Insert oven door hinge arm into hinge receiver until the hinge arm slots (see Figure 4) align with horizontal pins on the hinge receiver (see Figure 5) and place hinge arm onto the hinge receiver.

• Once the hinge arms are resting on the hinge receiver pins (see Figure 3) open oven door slowly to the "Full Open" position (see Figure 2).

• Rotate hinge locking lever UP to the locked position to secure the oven door to the unit (see Figure 1).

NOTE: Make sure that hinge locking lever is rotated fully UP to the locked position as shown (see Figure 1) before closing oven door.

Hinge Locking Lever

(Locked Position)

Figure 1

Jn!ocked Position)

CAUTION

Door will not close all the way and could fall off I when opened if the hinge locking levers are not

rotated fully UP to the locked position.

If hinge locking lever will not rotate fully UP to the locked

position as shown (see Figure 1) then the hinge arm is not properly seated on the receiver. Rotate the hinge locking lever DOWN to the unlocked position (see Figure

2) and remove oven door as outlined in the Oven Door Removal procedure. Then replace the oven door as

outlined in the Oven Door Replacement procedure,

making sure that the hinge arm slots are fully seated on

the horizontal pins in the hinge receiver.

• Once the hinge locking lever is rotated fully UP to the

locked position (see Figure 1) close the oven door.

Lever

lge Arm

Figure 4

Figure 3

Hing

Hinge Receiver

Horizontal Pins

Figure 5

+ 6 hidden pages