Jenn-air JFFCC72EFP Use & Care

0 (0)

JENN-AIR® FRENCH DOOR

REFRIGERATOR

RÉFRIGÉRATEUR ENCASTRÉ

CÔTE À CÔTE JENN-AIR

REFRIGERADOR EMPOTRADO

DE DOS PUERTAS JENN-AIR

Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico,

W10815172A

USE AND CARE GUIDE

For questions about features, operation/performance, parts, accessories, or service,

call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.

Get the app, connect instructions, terms of use, and privacy policy at www.jennair.com/connect.

GUIDE D’UTILISATION ET D’ENTRETIEN

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247)

ou visitez notre site Web à www.jennair.ca.

MANUAL DE USO Y CUIDADO

llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En Canadá, llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.ca.

Table of Contents/Table des matières/Índice...................................................................................2

TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE

REFRIGERATOR SAFETY .....................3

PARTS AND FEATURES ........................4

What’s New Behind the Doors? ............ 5

GETTING STARTED ...............................6 REFRIGERATOR CONNECTIVITY

FEATURES ...............................................7

CONNECTIVITY SETUP .........................8

INSTALLATION INSTRUCTIONS ..........10

Unpack the Refrigerator ........................10

Location Requirements .........................10 Remove and Replace

Refrigerator Doors .................................11 Remove and Replace Freezer

Drawer Fronts ........................................14

Electrical Requirements ........................15

Water Supply Requirements .................15

Connect the Water Supply ....................15

Handle Installation and Removal ..........16 Refrigerator Leveling

and Door Closing ..................................18

FILTERS AND ACCESSORIES ..............18

Water Filtration System .........................18

Install FreshFlow™ Air Filter .................20

Install Produce Preserver ......................20

Accessories ...........................................21

REFRIGERATOR USE ............................21

Opening and Closing Doors ..................21

Using the Controls ................................22

External Dispenser Controls .................24

Lighting the Refrigerator .......................24

Water and Ice Dispensers .....................24

Ice Maker and Storage Bin ..................27

Shelves, Bins, and Drawers ..................29

Freezer Drawers ....................................31

Audio Reference ....................................31

REFRIGERATOR CARE .........................32

Cleaning ................................................32

Lights .....................................................33

Vacation and Moving Care ....................33

TROUBLESHOOTING—

CONNECTED MODELS .........................34

TROUBLESHOOTING ............................35

PERFORMANCE DATA SHEET ............44

WARRANTY .............................................45

SÉCURITÉ DU RÉFRIGÉRATEUR ........46

PIÈCES ET CARACTÉRISTIQUES ........47

Quoi de neuf en coulisse? ....................48

MISE EN PLACE .....................................49 FONCTIONS DE CONNECTIVITÉ

DU RÉFRIGÉRATEUR ...........................50 CONFIGURATION

DE LA CONNECTIVITÉ ..........................52

INSTRUCTIONS D’INSTALLATION ......54

Déballage du réfrigérateur.....................54

Exigences d’emplacement ....................54 Retrait et réinstallation des portes

du réfrigérateur ......................................55 Retrait et remplacement de l’avant

du tiroir de congélation .........................58

Spécications électriques .....................59 Spécications de l’alimentation

en eau ....................................................59 Raccordement à la canalisation

d’eau ......................................................59

Installation et retrait des poignées ........61 Nivellement du réfrigérateur

et fermeture de la porte .........................62

FILTRES ET ACCESSOIRES .................63

Système de ltration d’eau ...................63 Installation du ltre à air FreshFlow™ ...64 Installation du conservateur

de produits frais ....................................65

Accessoires ...........................................66

UTILISATION DU RÉFRIGÉRATEUR ...66

Ouverture et fermeture des portes ........66

Utilisation des commandes ..................67 Commandes de distributeur externe ....69

Éclairage du réfrigérateur ......................69

Distributeurs d’eau et de glaçons .........69 Machine à glaçons et bac

d’entreposage ......................................72

Tablettes, balconnets, et tiroirs .............74

Tiroirs du congélateur ...........................76

Référence audio ....................................76

ENTRETIEN DU RÉFRIGÉRATEUR ......77

Nettoyage ..............................................77

Lampes ..................................................78 Précautions à prendre pour

les vacances ou le déménagement ......78

DÉPANNAGE –

MODÈLES AVEC CONNEXION .............79

DÉPANNAGE ...........................................80 FICHE DE DONNÉES RELATIVES

AU RENDEMENT ....................................90

GARANTIE ...............................................91

SEGURIDAD DEL REFRIGERADOR ... 93

PIEZAS Y CARACTERÍSTICAS ............ 94

¿Qué hay de nuevo detrás

de las puertas? ..................................... 95

PARA COMENZAR ................................ 96 CARACTERÍSTICAS

DE CONECTIVIDAD

EL REFRIGERADOR ............................. 98 CONFIGURACIÓN

DE LA CONECTIVIDAD ....................... 100 INSTRUCCIONES

DE INSTALACIÓN ................................ 102

Desembale el refrigerador .................. 102

Requisitos de ubicación ..................... 102 Cómo quitar y volver a colocar

las puertas del refrigerador ................ 103 Cómo quitar y volver a colocar

el frente de los cajones

del congelador ................................... 106

Requisitos eléctricos .......................... 107

Requisitos de suministro de agua ..... 107

Conexión del suministro de agua ...... 107

Cómo instalar y quitar las manijas ..... 109 Nivelación del refrigerador y cierre

de las puertas ..................................... 110

FILTROS Y ACCESORIOS .................. 111

Sistema de ltración de agua ............ 111

Filtro de aire FreshFlow™ .................. 112 Instale el preservador de alimentos

frescos ................................................ 113

Accesorios .......................................... 114

USO DEL REFRIGERADOR ................ 114

Cómo abrir y cerrar las puertas ......... 114

Uso de los controles .......................... 117 Controles del despachador

externo ............................................... 117

Iluminación del refrigerador ............... 117 Despachadores de agua y de hielo ... 117

Fábrica de hielo y depósito ................ 121

Estantes, depósitos y cajones ........... 122

Cajones del congelador ..................... 124

Referencia de audio ........................... 124

CUIDADO DEL REFRIGERADOR ...... 125

Limpieza ............................................. 125

Luces .................................................. 126 Cuidado durante las vacaciones

y las mudanzas .................................. 126

SOLUCIÓN DE PROBLEMAS —

MODELOS CONECTADOS ................. 127

SOLUCIÓN DE PROBLEMAS............. 128 HOJA DE DATOS

DE RENDIMIENTO ............................... 138

GARANTÍA ............................................ 139

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

■ Plug into a grounded 3 prong outlet. ■ Do not remove ground prong. ■ Do not use an adapter. ■ Do not use an extension cord. ■ Disconnect power before servicing. ■ Replace all parts and panels before operating. ■ Remove doors from your old refrigerator. ■ Connect to a potable water supply only. ■ Use nonflammable cleaner. ■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models). ■ Do not hit the refrigerator glass doors (on some models). ■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are still dangerous—even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors. ■ Leave the shelves in place so that children may not easily

climb inside.

PARTS AND FEATURES

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

In-Door-Ice® Storage Bin

Temperature Controls

Small Door Bin (2)

Air Filter

Herb Tender™ Container

Medium Door Bin

Gallon Door Bin

Wi-Fi SAID (smart appliance ID) sticker

Adjustable Glass Shelves

Fold-Away Glass Shelf

Pull-Out Platter

Humidiseal™ Crisper Drawers

TemperatureControlled Pantry Drawer

Gallon Door Bin (4)

Glide-Out Freezer Drawer

Water Filter

Wine Rack — Optional

What’s New Behind the Doors?

Your Jenn-Air® French door refrigerator comes equipped with various

innovative storage and energy-efcient features.

Obsidian Interior

This dramatic interior showcases food items throughout the refrigerator and provides a sharper contrast than white interiors. Includes coordinating crisper drawers and freezer.

Energy and Normal Operating Sounds

Your new French door bottom-mount refrigerator has been designed with a Linear Compressor to optimize energy efciency and better regulate temperatures to match cooling demand. You may notice that it operates differently than your previously owned refrigerator. This allows the refrigerator to respond at variable speeds and optimize cooling needs by avoiding abrupt start/stop cycles.

In-Door-Ice® Storage Bin

The ice maker and ice storage bin are located in the door for easy access to ltered ice while freeing up valuable shelf space inside and adding additional door bins for more usable space.

Twin Fresh™ Climate Control System

The refrigerator and freezer compartments have separate evaporators to provide fresh food and frozen food with optimal storage climates: cool and humid in the fresh food, cold and dry in the freezer, and no mixing of air between the compartments to reduce the transfer of food odors and tastes from refrigerator to freezer and allow freezer air to remain dry to control frost and reduce freezer burn.

FreshFlow™ Air Filter

An air lter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator. Replace your air lter every 6 months for maximum odor reduction.

Water Dispenser with Measured Fill

The Measured Fill feature allows you to dispense a desired amount of ltered water in handy increments like 8, 16, or 24 oz.

Water Dispenser with Favorite Fill

The Favorite Fill feature allows you to save 2 custom presets that can be programmed for favorite items that are frequently lled like a coffee pot or a water bottle.

Electronic Temperature-Controlled Pantry Drawer

This drawer provides precise, independent temperature control with 4 specialized settings for maximum exibility.

Herb Tender™ Container

This removable accessory provides a dedicated space to help optimize herb freshness.

Humidiseal™ Crisper Drawers

These drawers maintain a higher humidity level than the main refrigerator compartment to help keep produce fresh.

Interior LED Theater Lighting

Multiple strips of LED lights inside the refrigerator compartment, freezer compartment, and interior drawers minimize shadows and evenly distribute light throughout the refrigerator.

Soft, Auto-Close Technology

Provides smooth operation of drawer glides with an auto-close design that pulls drawers closed.

Door Ajar Alarm

A helpful alarm sounds when the refrigerator door or freezer drawer is left ajar.

Power Outage Indicator

If the power should go out while you are away from home, this indicator will let you know that the refrigerator has been without power.

Wi-Fi Connectivity

This refrigerator can connect with in-home Wi-Fi to provide remote control through an app, available to download for use with either iOS or Android devices.

House Symbol

This function automatically turns on after the appliance is provisioned and registered. Pressing the Connect button, will turn off this function temporarily.

Fold-Away Glass Shelf

This special shelf provides a exible storage option for tall items by allowing half the shelf to fold out of the way.

Pull-Out Platter

This full-width slide-out shelf is ideal for holding nished dishes waiting to be served or for ingredients needing more preparation.

To view videos on door removal/

replacement, door adjustment, water

filter installation, air filter installation,

shelf adjustment or removal, and

Wi-Fi (if applicable) connectivity,

scan the code to the left with your

mobile device.

GETTING STARTED

INSTALLATION CHECKLIST

✔ Electrical Power

❑ Plug refrigerator into a grounded 3 prong outlet.

✔ Doors

❑ If doors need to be removed during installation, see the

“Remove and Replace Doors” in the instructions.

❑ Check that handles are secure and installed according to the

instructions.

❑ Doors seal completely. ❑ Refrigerator is level. (Remove base grille and adjust leveling

feet so they are snug against the oor.)

❑ Doors are even across the top. (Use door alignment feature if

necessary.)

❑ Base grille is properly attached to the refrigerator.

✔ Ice and Water System (on some models)

❑ Connect refrigerator to a cold water supply with 20-120 psi

water pressure, as specied in the instructions.

❑ Make sure the household water supply is connected and

turned on.

❑ Check that the water supply line behind refrigerator is not

kinked.

❑ Only use recommended water supply tubing, copper, or PEX,

as specied in the instructions.

❑ Install water lter according to the instructions. ❑ Flush water system with 3 gallons of water, as specied in the

instructions.

❑ Check for water leaks at all connections. ❑ Turn on ice maker if refrigerator is connected to water supply.

(If not connected to water supply, turn off ice maker.)

✔ Final Checks

❑ Install air lter according to instructions in corresponding

packaging.

❑ Remove all shipping material. ❑ Set temperature controls to the recommended setting. ❑ Save instructions and other literature. ❑ Send in Registration Card or register your product online.

WATER FILTER INSTALLATION

❑ Locate the water lter compartment in the lower left-hand side

of the refrigerator compartment. Push on the right side of the lter door to open.

❑ Align the arrow on the water lter cap with the cutout notch in

the lter housing and insert lter.

❑ Once the lter is inserted, turn the lter clockwise 90° (quarter

turn) until it locks into the housing.

❑ Push water lter door closed to latch. ❑ Flush 3 gallons of water through the water system to clear air

from the water line and to keep the dispenser from dripping and/or avoiding decreased dispenser ow.

NOTE: If the lter is not installed correctly, water may dispense at a lower ow rate and there will be slower ice production. Improper lter installation may also cause the water lter housing to leak.

DOOR ALIGNMENT

Align Refrigerator Doors

✔ If doors are uneven:

❑ Ensure the refrigerator is level. ❑ Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin.

❑ Insert the short end of the ¹⁄

" hex-key wrench (packed with the

Door Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw.

To raise the refrigerator door, turn the hex key to the right. To lower the door, turn the hex key to the left.

❑ Continue to turn the alignment screw until the tops of the door

are aligned.

Shelf Height Adjustment

Shelf height can be adjusted by changing the adjustable shelf mounts between their vertical and horizontal positions.

■ Carefully lift the shelf off the shelf mounts and turn the ipper

to the desired orientation.

■ Repeat for remaining shelf mounts. ■ Ensure the shelf is properly seated on the shelf mounts.

ENERGY SAVER MODE AND NORMAL OPERATING SOUNDS

Your new French door bottom mount refrigerator has been designed to optimize energy efciency and better regulate temperatures to match cooling demand.

You may notice that it operates differently from your previously owned refrigerator.

It is normal for the high-efciency compressor to run for extended periods of time at varying speeds in order to consume only the energy necessary for optimum efciency.

In addition, during various stages of the cooling cycle, you may hear normal operating sounds that are unfamiliar to you.

Energy Saver Mode

A selectable feature that turns off the heaters around the refrigerator doors and dispenser. When this feature is enabled, condensation may form on the front of the refrigerator cabinet, gasket, or on top of the freezer drawer. Savings may vary based on the relative humidity of environment.

REFRIGERATOR CONNECTIVITY FEATURES

(on some models)

Wi-Fi connectivity allows your Smart Refrigerator to connect to the Internet and interact with the Jenn-Air app from your smartphone or mobile device. This connection opens up several Smart options to you — options intended to save you valuable time and energy. Refer to the “Troubleshooting—Connected Models” section of this Use & Care Guide, check any connection instructions for your specic router, and refer to alternate instructions at www.jennair.com/connect or call 1-877-559-2603.

NOTE: Requires Wi-Fi and account creation. App features and functionality subject to change. Subject to Terms of Service available at: www.jennair.com/connect. Data rates may apply.

Over Temperature

What it does: Sends you a notication when the temperature in

your refrigerator rises and reaches above a specied value in the refrigerator and freezer compartments.

What it does for you: Alerts you to over-temperature status to provide input regarding disposition of refrigerator/freezer contents.

Max Cool

What it does: Allows you to control your refrigerator remotely

from your mobile device via the Jenn-Air app. What it does for you: Lets you turn on/off Max Cool options

remotely to make temperatures colder in the refrigerator in anticipation of loading newly purchased grocery items. Lowers internal temperatures for 24 hours.

SMART FEATURES

Smart Features help make your everyday a little more efcient by letting you remotely monitor, manage, and maintain your refrigerator.

Remote Temperature Control

What it does: Allows you to control your refrigerator remotely

from your mobile device via the Jenn-Air app. What it does for you: Lets you control temperatures in your

refrigerator, freezer, and temperature-controlled pantry remotely— not just when you are standing in front of it.

Water Filter Status

What it does: Gives you a look at the life remaining for your water

lter before replacement is needed. This allows you to reset the lter.

What it does for you: Helps you be more efcient in planning for ordering and replacing lters.

Auto Reorder App

What it does: Allows you to order replacement lters,

consumables, and accessories via the Jenn-Air app for delivery directly to your home.

What it does for you: Simplies ordering correct water and air lters—no trips to the store searching for the correct lters.

Door Ajar Alert

What it does: Sends you a notication when one of the doors of

the refrigerator has been left open. What it does for you: Alerts you to door-open status so you

can close the door(s) or call home to ask someone else to close door(s) before over-temperature situation arises.

Power Outage Alerts

What it does: Sends you a notication when power

to your refrigerator is disconnected, returns, and when the highest temperature is reached in the refrigerator and freezer compartments during the power outage.

What it does for you: Alerts you to power status and duration of outage to provide input regarding disposition of refrigerator/ freezer contents.

Max Ice

What it does: Allows you to control your freezer remotely from

your mobile device via the Jenn-Air app. What it does for you: Lets you turn on/off Max Ice remotely

to increase ice production. Reduces the set temperature to the lowest possible setting for 24 hours to maximize ice production.

Pure Freeze™ Mode Control

What it does: Allows you to receive status of your refrigerator

remotely to your mobile device via the Jenn-Air app. What it does for you: Informs you whether Pure Freeze™ mode

is active in your refrigerator to reduce freezer burn and help frozen items maintain their appearance and taste.

Sabbath Mode

What it does: Allows the door of the refrigerator or freezer to be

opened or closed during the Sabbath or other religious holidays without activating the interior lights or controls. Allows you to turn on and off remotely from your mobile device via the Jenn-Air app.

What it does for you: Lets you turn on/off Sabbath mode options remotely.

Dispenser Light Brightness Control

What it does: Allows you to control your refrigerator remotely to

your mobile device via the Jenn-Air app. What it does for you: Lets you turn on/off the dispenser lighting

remotely.

Favorite Fill Control

What it does: Allows you to change your Favorite Fill values

on your refrigerator remotely using your mobile device via the Jenn-Air app.

What it does for you: Lets you set and save Favorite Fill values remotely.

GET STARTED

Refer to the Quick Connect packet that came with your refrigerator, or go to www.jennair.com/connect and follow the instructions to get connected.

Check the Jenn-Air app frequently for additional information and features.

Requires Wi-Fi and account creation. App features and functionality subject to change. Subject to Terms of Service available at: www.jennair.com/connect. Data rates may apply.

CONNECTIVITY SETUP

(on some models)

IMPORTANT: Proper installation of your refrigerator prior to use is your responsibility. Be sure to read and follow the User Instructions that came with your refrigerator.

Automatic Set-Up Instructions—Wi-Fi Protected Setup (WPS)

You will need:

■ A home wireless router capable of WPS. The router should

be ON and have a live Internet connection.

■ The Smart Appliance Identication Number (SAID) from your

refrigerator. This is located on a sticker on the front side of the right-hand hinge cover of the refrigerator.

NOTE: If your home wireless router is not equipped with a WPS button, please check the user manual of your router to conrm if it is WPS capable. If not, alternate set-up instructions are at

www.jennair.com/connect.

1. Setup router

2. Setup refrigerator

(time-sensitive step)

Press the WPS button on the router. An indicator light will begin blinking.

HELPFUL TIP: The WPS function on your router is active for 2 minutes. Complete the next step within that timeframe or you will need to reinitiate WPS.

Press and hold Connect button for 3 seconds on Home screen. The Wi-Fi status indicator ( ) on the refrigerator control panel

will blink slowly while your refrigerator and router attempt to connect.

If the connection is successful, the Wi-Fi status indicator will come on and remain lit.

If Your Refrigerator Doesn’t Connect:

If your refrigerator and router fail to connect after 2 minutes, the Wi-Fi status indicator will blink rapidly for 5 seconds and then turn off. Refer to the “Troubleshooting—Connected Models” section of this Use & Care Guide, check any connection instructions for your specic router, and refer to alternate instructions at www.jennair.com/connect or call

1-877-559-2603.

NOTE: If this is your rst Smart Appliance, you will need to

download the Jenn-Air app and create an online user account. If you already have the app and a user account, please skip

ahead to Step 4 “Register your refrigerator in your user account.”

To disconnect Wi-Fi, press and hold Connect button between 7 and 15 seconds, the <Wi-Fi> and <house> icons will turn off, indicating that you have disabled the Wi-Fi radio.

To reconnect Wi-Fi, press and hold Connect button for 3 seconds on the Home screen.

The Wi-Fi status indicator ( ) on the refrigerator control panel will blink slowly while your refrigerator and router attempt to connect.

If the connection is successful, the Wi-Fi status indicator will come on and remain lit.

To disconnect your refrigerator from your router, press and hold CONNECT for more than 15 seconds. The <Wi-Fi> and <house> icons will turn off, indicating that your refrigerator is completely disconnected from Wi-Fi and your router.

To re-connect your refrigerator to your router and reconnect Wi-Fi, press and hold CONNECT for 3 seconds on the Home screen.

The Wi-Fi status indicator ( ) on the refrigerator control panel will blink slowly while your refrigerator and router attempt to connect.

If the connection is successful, the Wi-Fi status indicator will come on and remain lit.

Press the WPS button on the router. An indicator light will begin blinking.

HELPFUL TIP: The WPS function on your router is active for 2 minutes. Complete the next step within that timeframe or you will need to reinitiate WPS.

3. Download Jenn-Air app and

set up user account

From your mobile device, smartphone, or tablet, go to www.jennair.com/connect and follow the instructions to download and install the Jenn-Air app.

Once installed, tap the Jenn-Air app icon to open the app. You will be guided through the steps to set up a user account. The app will make sure to get the necessary personal and home information as well as information about your energy company.

4. Register your refrigerator in your

user account

Registering your refrigerator in your account is a necessary step in order for you to take full advantage of the Smart features. When prompted by the app, enter the SAID (case sensitive), which can be found on a sticker on the front side of the right hand hinge cover of the refrigerator.

My Smart Appliance ID# is:

■ The Wi-Fi status indicator on the refrigerator control panel

will blink slowly while your refrigerator and router attempt to connect.

■ Note that this blinking only applies to rst-time registration

after provisioning. No blinking behavior for automatic reconnection after a connection is established.

■ Once you’ve connected your refrigerator to your home

Wi-Fi network, it will remain linked even if the power goes out, you move the appliance, or if you put it in storage for a while.

■ If you replace your wireless router (or get a different

Smart refrigerator), you will need to repeat this connectivity set-up process.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Refrigerator Delivery

■ A minimum door opening of 33" (838 mm) is required. If

door opening is 36" (914 mm) or less, then removal of doors, drawer, and hinges is required.

■ Cart the refrigerator from the side for all door openings

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning on

the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your ngers. Wipe with warm water and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

■ Dispose of/recycle all packaging materials.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household use only.

To ensure proper ventilation for your refrigerator, allow for a minimum ¹⁄2" (1.25 cm) of space on each side and at the top. Allow for a minimum 1" (2.54 cm) space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a xed wall, leave a 3³⁄4" (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source such as an oven or radiator.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Refrigerator Care” section.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

¹⁄2" (1.25 cm)

3³⁄4" (9.5 cm)

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your house door opening to see whether or not you need to remove the refrigerator doors to move the refrigerator into your home. If refrigerator door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator control off. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors. TOOLS NEEDED: TORX® T25®† screwdriver and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Water Dispenser

Tubing Connection

A. Outer ring

Wiring Plug

Top Right Hinge

A. TORX® T25® screws B. Hinge cover screw C. Top hinge cover D. Top hinge

Door at 90° Angle

to Cabinet

Top Left Hinge

A. TORX® T25® screws B. Ground wire (Do not remove.) C. Do not remove screws.

†®TORX and T25 are registered trademarks of Acument Intellectual Properties, LLC.

90°

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Bottom Door Hinge

For your convenience, the refrigerator doors have bottom hinges with door closers. These closers allow the doors to swing fully closed with just a gentle push.

IMPORTANT: So that the closers feature will operate properly, the doors must be removed only when open to a 90° angle to the front of the cabinet. If one or both doors were not at a 90° angle when removed, the bottom door hinge must be reset.

A. Hinge base parallel to the bottom edge of the door

4. Turn the hinge until the hinge base is at a 90° angle to the

bottom edge of the door.

90°

Reset the Door Hinge

1. Lift the door from the bottom hinge pin, and place it on a

at surface.

2. Using a TORX® T25® screwdriver, remove the bottom hinge

with the bushing from the cabinet.

A. Bushing B. Hinge base

3. Insert the bottom hinge and bushing into the corresponding

slot in the bottom of the door.

NOTE: Make sure that the base of the hinge is parallel to the bottom of the door.

A. Hinge base turned to a 90° angle with the bottom edge of the door

5. Remove the hinge from the door. Using a TORX® T25®

screwdriver, reattach the bottom hinge to the refrigerator cabinet.

6. The hinge is now reset and prepared for the door to be

replaced. See “Replace Refrigerator Doors” later in this section.

Remove Refrigerator Doors

WARNING

Electrical Shock Hazard Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Remove Right-Hand Door

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

3. Using a Phillips screwdriver, remove the cover from the

top hinge.

4. Using the TORX® T25® screwdriver, remove the 2 screws from

the top hinge and set aside.

A. Top hinge cover screw B. Top hinge cover

C. TORX® T25® screws D. Top hinge

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

5. Open the door until it is at a 90° angle to the front of the

cabinet.

6. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

Remove Left-Hand Door

3. Disconnect the wiring plug located on top of the door hinge.

■ Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of the plug apart.

NOTE: Do not remove the green ground wire. It should remain attached to the door hinge.

4. Using the TORX® T25® screwdriver, remove the 2 internal

screws from the top hinge and set aside.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

IMPORTANT: The tubing and wiring for the water dispenser run through the left-hand door hinge, so they must be disconnected before removing the door.

1. Using a at head screwdriver, remove the cover from the top

hinge.

A. Top hinge cover screw B. Top hinge cover

2. Disconnect the water dispenser tubing located on top of the

door hinge. Firmly pull up on the clasp. Then, pull the tubing out of the fitting.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

A. TORX® T25 B. Ground wire (Do not remove.)

screws

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a doorway.

■ Only if necessary, use a TORX

T25® screwdriver to

remove the bottom hinges and brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top

of the refrigerator door.

3. Using the 3 TORX® T25® screws, fasten the hinge

to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the 3 TORX® T25® screws, fasten the hinge to the

cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing. Insert the tubing rmly into the tting until it stops. Close the

clasp around the tubing. The clasp snaps into place between the tting and the collar. Connect blue female side with blue male side and clasp. Repeat with gray female and gray male side.

4. Reconnect the electrical wiring.

■ Push together the 2 sections of the wiring plug.

Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the top screws,

located at the bottom inside the drawer front, with the drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady while another person aligns the drawer front and inserts the studs into the slots.

Final Steps

1. Completely tighten the 6 internal TORX® T25® screws (3 on

the right-hand door hinge and 3 on the left-hand door hinge).

2. Replace both top hinge covers.

Remove and Replace

Freezer Drawer Fronts

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the 2 top screws that fasten the drawer front to the

drawer glides. The 2 screws (1 on the left-hand side and 1 on the right-hand side) are located inside the drawer front.

3. Remove the 2 screws at the bottom, inside the drawer front

that fasten the drawer front to the drawer glides.

4. Lift up on the drawer front to release the screws from the

drawer glide bracket slot.

A. Drawer front screw

3. Tighten the 2 screws at the top of the drawer front (1 on the

left-hand side and 1 on the right-hand side) and install the 2 screws on the bottom.

Final Steps

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See the “Using the Controls” section.

3. Return all removable parts and food to the drawers.

A. Drawer glide bracket slots

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its nal location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115-volt, 60 Hz, AC-only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator and approved accessories be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and avor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of the food.

NOTE: Before performing any type of installation or cleaning, turn off cooling, and then disconnect the refrigerator from the electrical source. When you have nished, reconnect the refrigerator to the electrical source and turn on cooling. See the “Using the Controls” section.

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualied plumber.

NOTE: If the water pressure is less than what is required, the ow of water from the water dispenser could decrease or ice cubes could be hollow or irregular shaped.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system and supplying the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water ltration system is connected to your home cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy use. The tank capacity could be too small to keep up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are not recommended.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse osmosis system. Remove the water lter. See the “Water Filtration System” section.

If you have questions about your water pressure, call a licensed, qualied plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ Plumbing must be installed in accordance with the

International Plumbing Code and any local codes and ordinances.

■ Copper and PEX tubing connections from the household

water line to the refrigerator are acceptable and will help avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the following Part Numbers: W10505928RP (7 ft [2.14 m] jacketed PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP (25 ft [7.62 m] PEX).

■ Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■

⁄16" and 1⁄2" open-end wrenches or two adjustable wrenches

■

⁄4" nut driver

NOTE: Do not use a piercing-type or ³⁄16" (4.76 mm) saddle valve which reduces water ow and clogs easier.

Connect to Water Line

IMPORTANT: If you have turned the refrigerator on before the

water was connected, turn off the ice maker.

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to reduce water pressure in the water line.

3. Use a quarter-turn shut-off valve or the equivalent, served by

a 1⁄2" household supply line.

NOTE: To allow sufcient water ow to the refrigerator, a minimum

⁄2" (12.7 mm) size household supply line is recommended.

A B

A. Sleeve B. Nut

C. Copper tubing (to refrigerator) D. Household supply line (½" minimum)

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1⁄4" (6.35 mm) O.D. (outside diameter) soft copper tubing to connect the shut-off valve and the refrigerator.

■ Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut onto copper

tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

Complete the Installation

WARNING

A. Compression sleeve B. Compression nut

5. Place the free end of the tubing into a container or sink and

turn on main water supply to ush out tubing until water is clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the nal

connection to the inlet of the water valve to avoid possible water valve malfunction.

6. Bend the copper tubing to meet the water line inlet which

is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specic to your model.

1. Remove plastic cap from water valve inlet port. Attach the

copper tubing to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Conrm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a “P” clamp.

C. Copper tubing

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See the “Water and Ice Dispensers”

section.

NOTE: Allow 24 hours to produce the rst batch of ice. Discard the rst 3 batches of ice produced. Allow 3 days to completely ll the ice storage bin.

Handle Installation and Removal

Parts Included: refrigerator door handles (2), freezer drawer handle (1), 1⁄8" hex key, spare setscrew(s)

NOTE: The freezer drawer handle is shorter than the refrigerator door handles. Handle style may vary by model.

Install Handles

Refrigerator Doors NOTE: Handle mounting setscrews are preinstalled inside

the handle.

1. Remove the handles from the packaging inside the

refrigerator and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed

door, place a handle onto the shoulder screws so that the setscrews are facing the adjacent door.

A. Copper tubing B. “P” clamp

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

4. If ice is desired, turn on the ice maker. 16

C. Compression nut D. Compression sleeve

A. Shoulder screws B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is ush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until key is engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew just until

setscrew begins to contact the shoulder screw. Do not fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

7. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter turn. The handle is not properly installed without this extra tightening.

8. Repeat steps 2 through 7 to install the other handle onto

the adjacent refrigerator door.

Freezer Drawer

1. With the drawer closed, place the handle onto the shoulder

screws so that the setscrews are facing down toward the oor.

4. Using a left-to-right motion, tighten the setscrew a quarter

turn at a time just until setscrew begins to contact the shoulder screw. Do not fully tighten.

5. Repeat steps 3 and 4 to fasten the right-hand setscrew to

the shoulder screw.

6. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter turn. The handle is not properly installed without this extra tightening.

7. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into a setscrew hole and slightly rotate the hex key until it is engaged in the setscrew.

2. Using a right-to-left motion, loosen the setscrew a quarter

turn at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull

the handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

A. Shoulder screw B. Setscrews inside the handle

2. Firmly push the handle toward the drawer until the handle

base is ush against the drawer.

3. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until key is engaged in the setscrew.

Refrigerator Leveling

and Door Closing

The base grille covers the adjustable brake feet and roller assemblies located at the bottom of the refrigerator below the freezer drawer. Before making any adjustments, remove the base grille and move the refrigerator to its nal location.

Tools Needed: ¼" hex driver Tools Provided: 1/8" hex-key

1. Use a ¼" hex driver to remove both screws in base grille.

2. Remove the base grille. Using both hands, grasp the grille

rmly and pull it toward you. Open the freezer drawer to access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the brake feet by turning them counterclockwise. The front rollers will be touching the oor.

3. Move the refrigerator to its nal location.

4. Using the 1⁄4" hex driver, lower the brake feet. Turn them

clockwise until the rollers are off the oor and both brake feet are snug against the oor. This keeps the refrigerator from rolling forward when opening the refrigerator doors or freezer drawer.

IMPORTANT: If you need to make further adjustments involving the brake feet, you must turn both brake feet the same amount to keep the refrigerator level.

5. Use a level to make sure the refrigerator is level from side to

side and front to back.

6. Make sure the doors are even at the top and that the space

between the bottom of the refrigerator doors and the top of the freezer drawer is even. If necessary, align the doors.

To Align the Doors:

■ Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin.

■ Insert the short end of the ¹⁄

the Door Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw.

To raise the refrigerator door, turn the hex key to the right. To lower the door, turn the hex key to the left.

" hex-key wrench (packed with

■ Continue to turn the alignment screw until the doors are

aligned.

A. Bottom hinge pin B. ¹⁄8" hex-key wrench

7. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when a door or drawer is pulled open, adjust the brake feet.

To Steady the Refrigerator:

■ Open the freezer drawer. Using a ¹⁄

brake feet clockwise the same amount until the brake feet are snug against the oor. Check again. If not satised, continue to adjust the brake feet by half turns of the screw until the refrigerator does not roll forward when the drawer is opened.

NOTE: Having someone push against the top of the refrigerator takes some weight off the brake feet. This makes it easier to turn the screws. Do not push with excessive force that tilts the refrigerator.

8. Replace the base grille by aligning the ends of the grille with

the leveling assemblies on each side and snapping the grille into place. Use a ¼" hex driver to reinstall screws.

" hex driver, turn both

FILTERS AND ACCESSORIES

Water Filtration System

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Replace and Install the Water Filter

The water lter should be replaced every 6 months based on a ow rate of .50 gpm – .60 gpm that lters 200 gallons of water.

To order a replacement lter, contact us. See the “Accessories” section in the Use and Care Guide for information on ordering.

1. Push the water lter door to open, located at the bottom left

of refrigerator compartment.

6. Insert the lter into the housing.

2. Twist the water lter and turn 90° counterclockwise to unlock.

3. Pull the lter out of the housing.

7. Twist the water lter and turn 90° clockwise until it locks into

place and the arrows are aligned.

8. Push the water lter door closed.

4. Remove the water lter cap from the water lter being

replaced.

5. Install the water lter cap onto the new lter. Be sure to align

the arrows so the groves in lter align with ribs in lter cap.

The Water Filter Status Lights

The Water Filter status lights will help you know when to change your water lter. The app will also send notications to your mobile device and tell you the status of the Jenn-Air app for the lter life.

■ ORDER FILTER (yellow) - It is almost time to change the

water lter. “Order Filter” display is ON all of the time but OFF in Showroom mode and Sabbath mode.

■ REPLACE FILTER (red) - Replace the water lter. While you

are dispensing water, “Replace Filter” will blink 7 times and an alert tone will sound 3 times.

NOTE: “REPLACE FILTER” will remain illuminated if the lter is not reset on the user interface (UI).

■ RESET FILTER - Touch MAX COOL and MAX ICE for

3 seconds to reset water lter. The display will do a 3-second countdown, then ash the icon and play a tone.

Install FreshFlow™ Air Filter

An air lter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator.

On some models, your refrigerator’s accessory packet includes an air lter which must be installed prior to use.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene to slow the ripening process of many produce items. As a result, certain produce items will stay fresh longer.

Ethylene production and sensitivity varies, depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate-to-high amounts of ethylene.

Installing the FreshFlow™ Air Filter

Install the air lter behind the vent cover, located on the rear wall near the middle of the refrigerator.

1. Remove the air lter from its packaging.

2. Pull out plastic cover over the vented cover.

NOTE: When cover is removed for the rst time, a small

foam part the size of the lter will need to be removed and discarded.

3. Snap lter into place, close cover.

A. Air filter

Replacing the FreshFlow™ Air Filter

The disposable air lter should be replaced every 6 months. Some air lters have an indicator that replacement is needed.

To order a replacement air lter, contact us. See the “Accessories” section in the Use and Care Guide for information on ordering.

1. Open cover and remove the used air lter by squeezing in on

the side tabs.

2. Install the new air lter using the instructions in the previous

section.

Sensitivity

to Ethylene

Apples High Very High Asparagus Medium Very Low Berries Low Low Broccoli High Very Low Cantaloupe Medium High Carrots Low Very Low Citrus Fruit Medium Very Low Grapes Low Very Low Lettuce High Very Low Pears High Very High Spinach High Very Low

Installing the Produce Preserver

For your convenience, the suction-mounted produce preserver can be installed in either the crisper or the refrigerated drawers.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, rinse with water.

1. Wash the interior of a drawer with a solution of mild dish soap

and warm water and dry thoroughly.

2. Find the package containing the Produce Preserver inside the

refrigerator and install the Produce Preserver into the drawer, according to the instructions provided in the package.

Ethylene

Production

Replacing the Produce Preserver

The disposable packet(s) should be replaced every 6 months or when the status indicator changes completely from white to red.

To order replacements, contact us. See the “Accessories” section for information on ordering.

1. Remove the used packets from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement packets and status indicator using the

instructions included in the package.

Accessories

The following accessories are available for your refrigerator. To order an accessory, contact us and ask for the part number.

In the U.S.A., visit our website www.jennair.com/accessories or call 1-800-JENNAIR (1-800-536-6247).

In Canada, visit our webpage www.jennair.ca or call

1-800-JENNAIR (1-800-536-6247). affresh® Stainless Steel Cleaner:

In U.S.A., order Part #W10355016 In Canada, order Part #W10355016B

affresh® Stainless Steel Wipes: In U.S.A., order Part #W10355049 In Canada, order Part #W10355049B

affresh® Kitchen & Appliance Cleaner: In U.S.A., order Part #W10355010 In Canada, order Part #W10355010B

Water Filter: In U.S.A., order Part #EDR2RXD1 In Canada, order Part #EDR2RXD1B

Air Filter: Order Part #W10311524 or AIR1

Produce Preserver Starter kit: Order Part #P1KL6S1CS

Produce Preserver Rell kit: Order Part #P1KC6R1

Herb Tender™ Container: Order Part #W10882409

REFRIGERATOR USE

Opening and Closing Doors

There are 2 refrigerator compartment doors. The doors can be opened and closed either separately or together. There is a vertically hinged seal on the left refrigerator door.

■ When the left-side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

■ When both doors are closed, the hinged seal automatically

forms a seal between the 2 doors.

A. Hinged seal

Using the Controls

The touch-activated controls are located above the external dispenser and on the side of the left inner refrigerator door.

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are preset at the factory.

When you rst install your refrigerator, make sure that the controls are still set to the recommended set points. The factory-recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

■ Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the set points to a colder-than-recommended

setting will not cool the compartments any faster.

■ If the temperature is too warm or too cold in the refrigerator or

freezer, rst check the air vents to be sure they are not blocked before adjusting the controls.

■ The recommended settings should be correct for normal

household use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is rm.

NOTE: Areas such as a garage, basement, or porch may have

higher humidity or extreme temperatures. You may need to adjust the temperature away from the recommended settings to accommodate for these conditions.

■ Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

View Temperature Set Points

1. Touch [+]/[—] for refrigerator or [+]/[—] for freezer to toggle

through temperature set points.

NOTE: To view temperature in degrees Celsius, touch and hold the [°F/°C] button for 3 seconds and the temperature display will change. To return to Fahrenheit, touch and hold [°F/°C] for 3 seconds and the temperature display will change.

To activate Temperature mode for Pantry Drawer, touch DRAWER and toggle through 4 optional temperature settings: Meat, Beverage, Assorted, and Deli. The display will show the temperature set point of the selected setting for the Pantry Drawer.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

Adjust Temperature Set Points

Refrigerator set point range: 33°F to 45°F (1°C to 7°C) Freezer set point range: -6°F to 5°F (-22°C to -15°C)

1. Touch [+]/[—] to adjust the Refrigerator zone. The display will

show the temperature set point of the selected compartment as shown.

2. When the temperature in is the range of Pure Freeze™, the

display will light up. Pure Freeze™ is active at the coldest freezer set point.

When adjusting temperature set points,

use the following chart as a guide:

CONDITION TEMPERATURE ADJUSTMENT

REFRIGERATOR too cold REFRIGERATOR setting 1° higher REFRIGERATOR too warm REFRIGERATOR setting 1° lower FREEZER too cold FREEZER setting 1° higher FREEZER too warm/

FREEZER setting 1° lower

Too little ice

Max Cool

Pure Freeze™ Mode

The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

■ To turn on the Max Cool feature, press the Max Cool button.

When the button is pressed, the icon will blink 3 times and appear on the display screen.

■ To manually turn off the Max Cool feature, press the Max Cool

button and the display will blink 3 times and turn off. The Max Cool feature will remain on for 24 hours unless manually turned off. Adjusting the refrigerator temperature will automatically turn off the Max Cool feature. NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Max Ice

The Max Ice feature assists with increasing the cooling for the freezer compartment in order to increase ice production.

■ To turn on or off the Max Ice feature, press the Max Ice button.

When the button is pressed to turn the feature on, the icon will blink 3 times, and appear on the display screen.

■ To manually turn off the Max Ice feature, press the Max Ice

button and the display will blink 3 times and turn off. The Max Ice feature will remain on for 24 hours unless manually turned off. Adjusting the refrigerator temperature will automatically turn off the Max Ice feature. NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Water Filter Reset

Displays the status of the water filter. To reset the filter, press MAX ICE and MAX COOL for 3 seconds. After countdown, the Good icon will blink 3 times and remain lit.

NOTE: The Water Filter status lights on the internal controls will let you know when to change your water lter.

■ ORDER FILTER (Yellow) - Order a replacement water lter. ■ REPLACE FILTER (Red) - Replace the water lter. While you

are dispensing water, “Replace” Filter icon will ash constantly from beginning to the end of dispensing. After 14 days without replacing the water lter, the “Replace” Filter icon will blink 7 times and an alert tone will sound 3 times at the end of dispensing. See the “Water Filtration System” section. NOTE: REPLACE FILTER will remain illuminated if a lter reset is not done.

■ RESET FILTER - Touch MAX ICE and MAX COOL at the same

time on the Temperature Control display for 3 seconds to reset water lter. The display will do a 3-second countdown and then ash the icon and play a tone.

Filter Status

The Jenn-Air app will send an alert that displays the water lter status.

Energy Saver Mode

■ To turn the mullion heater off, press and hold the Energy Saver

button for 3 seconds. The Energy Saver icon will blink 3 times and then remain lit as shown.

IMPORTANT: When Energy Saver is enabled and the LED is ON, the dispenser heater and vertical mullion heater will be turned off.

■ Press and hold ENERGY SAVER for 3 seconds again to turn

the heaters back on.

This feature minimizes moisture migration from frozen food. This, in turn, reduces the freezer burn occurrence.

To turn on the Pure Freeze™ mode, toggle to the coldest freezer temperature set point.

To turn off the Pure Freeze™ mode, toggle from the coldest freezer set point to any other temperature.

Sound On/Off

The Sound button allows the customer to turn the sound on and off.

■ To turn on the Sound feature, press the Sound button. When

the button is pressed, the Sound icon will blink 3 times and appear on the display screen.

■ To manually turn off the Sound feature, press the Sound button

and the display will blink 3 times and turn off.

Power Outage

The Power Outage indicator lets you know if the power supply to the refrigerator has been off and the freezer temperature has risen.

The control panel display will read “Power Outage” and an alert tone will sound 3 times. Touch any button to stop the tone and touch any button again to turn off Power Outage icon.

Once the power outage has been conrmed, “Power Outage” icon will disappear and the display will return to the Home screen.

Showroom Mode

This mode is used when the refrigerator is on display in a retail store or if you want to turn the cooling off and deactivate all other functions except interior lighting. Showroom mode can be used when going on vacation. See the “Vacation and Moving Care” section for proper steps on leaving your refrigerator in this mode for long periods of time.

If you turn on Showroom mode, the word “Showroom” will light up on the display. Enter or exit Showroom mode by pressing and holding °F/°C and DRAWER at the same time for 3 seconds.

NOTE: Empty ice maker if refrigerator is going to be turned off for an extended period of time.

Sabbath Mode

Allows the door of the refrigerator or freezer to be opened or closed during the Sabbath or other religious holidays without activating the interior lights or controls.

The freezer and refrigerator user set points remain unchanged while in this mode. If you unintentionally turn on Sabbath mode, the word “Sabbath” will light up on the display. Enter and exit Sabbath mode by pressing and holding °F/°C and SOUND at the same time for 3 seconds.

NOTE: You will be unable to dispense or change temperature set points in Sabbath mode. Your interior lighting and control panels will all be inactive in Sabbath mode.

Calibration

Door

Replace

"#$#!

%&#'#(')!"#$#!

Order Filter

a1 oz = b1 L

a2 oz = b2 L

a3 oz = b3 L

Dispense

External Dispenser Controls

Water and Ice Dispensers

The control is located above the external dispenser of the refrigerator.

IMPORTANT: The display screen on the dispenser control panel will turn off automatically and enter “sleep” mode when the control buttons and dispenser paddles have not been used for 2 minutes or more. Touch any control button to reactivate the display screen. The Home screen will appear as shown.

Additional Features

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the refrigerator door(s) or freezer drawer is open for 5 minutes and cooling is turned on. The alarm will repeat every 2 minutes. Close all doors and drawer to turn it off.

NOTE: To mute the audible alarm while keeping the doors open, such as while cleaning the inside of the refrigerator, touch any button on the control panel. The alarm sound will be temporarily turned off, but the Door Ajar icon will still be displayed on the dispenser control panel.

IMPORTANT:

■ Allow 3 hours for the refrigerator to cool down and chill water. ■ Allow 24 hours to produce the rst batch of ice. Discard the

rst 3 batches of ice produced.

■ The dispensing system will not operate if the left-hand

refrigerator door is open.

Lighting the Refrigerator

The refrigerator has an interior light that comes on any time the door is opened.

NOTE: The light is an LED which does not need to be replaced. If the LED does not illuminate when the door is opened, call service to replace the light. See “Assistance or Service” in the “Warranty” section for contact information.

A. Water dispenser paddle B. Ice dispenser paddle

Flush the Water System

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water lter, ush the water system.

Flushing the water dispensing system forces air from the water line and lter and prepares the water lter for use. Additional ushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds. Repeat steps

1 and 2 until water begins to ow.

3. Once water begins to ow, continue depressing and releasing

the dispenser pad (5 seconds ON, 5 seconds OFF) until a total of 3 gal. (12 L) has been dispensed.

Calibrate Measured Fill

Calibration

Door

Replace

"#$#!

%&#'#(')!"#$#!

Order Filter

a1 oz = b1 L

a2 oz = b2 L

a3 oz = b3 L

Dispense

Save Favorite Fill

Household water pressure may affect the accuracy of the Measured Fill feature. So, for optimum performance of your water dispenser, you must rst calibrate Measured Fill.

IMPORTANT:

■ Flush the water system before calibrating Measured Fill. ■ For best results, calibration should be performed when water is

not being used in the house.

1. Place a sturdy measuring cup (1-cup [237 mL] size) on the

dispenser tray centered in front of the ice/water dispenser paddle.

NOTE: Depending on your model, a measuring cup may be provided.

Household water pressure may affect the accuracy of the Favorite Fill feature. So, for optimum performance of your water dispenser, you must rst calibrate Measured Fill.

IMPORTANT:

■ Flush the water system before saving Favorite Fill. ■ For best results, calibration should be performed when water is

not being used in the house.

1. Place a preferred-size cup on the dispenser tray centered in

front of the ice/water dispenser paddle.

2. Select either Favorite 1 or Favorite 2, and then touch and

hold Favorite Fill for 3 seconds to enter into Saving mode. The Favorite Fill icon will illuminate and remain lit while the Favorite Fill feature is being saved.

NOTE: You may touch FAVORITE FILL to exit at any time in Saving mode and the display will return to the Home screen.

3. Press and hold the water dispenser paddle, as needed, to

dispense water to the preferred-size cup.

NOTE: If overlling or spilling occurs, discard the water and restart the saving process.

4. When the preferred amount of water has been correctly

dispensed into the cup, touch Favorite Fill to conrm the favorite amount.

5. When Favorite Fill amount has been conrmed, the display

will return to the home screen.

Dispensing

A. Water dispenser paddle B. Ice dispenser paddle C. Measuring cup (1 cup)

Ensure that you do not have any Measured Fill preset selected.

2. Touch and hold the Measured Fill button for 3 seconds to

enter into Calibration mode. The Calibration and Measured Fill icons will illuminate and remain lit while the Measured Fill feature is being calibrated.

NOTE: You may touch MEASURED FILL to exit at any time in Calibration mode. The Calibration and Measured Fill icons will disappear.

3. Press and hold the water dispenser paddle, as needed, to

dispense water to the 1-cup ll line in the measuring cup.

NOTE: If overlling or spilling occurs, discard the water and

restart the calibration process.

4. When 1 cup of water has been correctly dispensed into

the measuring cup, touch MEASURED FILL to conrm the calibration.

5. When Measured Fill calibration has been conrmed, the

Calibration icon will disappear and the display will return to the home screen.

Touch CUBED ICE or CRUSHED ICE for your ice selection.

NOTES:

■ For crushed ice, cubes are crushed before being dispensed.

This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal and pieces of ice may vary in size.

■ When changing from crushed to cubed, a few ounces of

crushed ice will be dispensed along with the rst cubes.

Dispensing Water

IMPORTANT:

■ Dispense at least 1 qt (1 L) of water every week to maintain

a fresh supply.

■ If the ow of water from the dispenser decreases, it could

be caused by low water pressure.

■ With the water lter removed, dispense 1 cup (237 mL)

of water. If 1 cup (237 mL) of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

■ If it takes longer than 8 seconds to dispense 1 cup

(237 mL) of water, the water pressure to the refrigerator is lower than recommended. See the “Water Supply Requirements” and “Troubleshooting” sections for suggestions.

To Dispense Water - Standard:

1. Press a sturdy glass against the water dispenser paddle.

2. Remove the glass to stop dispensing. NOTE: The Dispense Water button does not enable standard

dispensing. It only functions in Measured Fill or Favorite Fill mode.

To Dispense Water - Measured Fill:

Measured Fill allows you to dispense a specied amount of water with the touch of a few buttons.

1. Put a sturdy glass under water spout. Touch MEASURED

FILL to activate.

NOTE: The amount of water you select will be dispensed. Make sure the container can hold the entire volume. If ice is in the container, you may need to adjust your selection.

2. Touch MEASURED FILL to turn on, then touch to select

8 oz (0.2 L), 16 oz (0.5 L), or 24 oz (0.7 L). Touch the fourth time to exit Measured Fill display.

3. Touch DISPENSE WATER (center button) or press paddle

and the selected amount of water will be dispensed.

NOTES:

■ The Measured Fill dispenser will automatically time out after

1 minute of inactivity.

■ You can rell several glasses with the same measurement by

continuing to touch DISPENSE WATER (center button) after each glass ll.

Measured Fill options are listed in the following chart:

Units

Ounces 8 16 24

Cups 1 2 3

Liters 0.2 0.5 0.7

NOTE: Most coffee cups (commonly 4 to 6 oz [118 to 177 mL] per cup) are not the same size as a measuring cup (8 oz [237 mL]). You may need to recalibrate Measured Fill to underll or to avoid unintentionally overlling coffee cups.

4. Dispense water. NOTE: While dispensing water, the ow of water will

automatically stop once the desired volume has been dispensed.

■ Press a sturdy glass against the dispenser paddle below

the water spout.

■ Place the glass below the water spout and touch

DISPENSE WATER for hands-free dispensing.

5. To pause dispensing before the selected volume has been

dispensed, touch DISPENSE WATER a second time or touch the water dispenser paddle. Touch DISPENSE WATER or paddle again to resume dispensing remaining amount.

NOTE: If you stop dispensing before the desired volume has been dispensed, the display will turn off after 1 minute. If you have not resumed by then, it will reset back to the original amount.

6. To select a new volume or start dispensing the same volume

again, you must rst nish dispensing the selected volume or turn off the Measured Fill feature (either by waiting 1 minute, so it will automatically turn off, or by touching CUBED ICE or CRUSHED ICE to manually turn it off), and then select Measured Fill again.

To Dispense Water - Favorite Fill:

Favorite Fill allows you to dispense a preferred amount of water with the touch of a few buttons.

1. Put a sturdy glass under water spout. Touch FAVORITE FILL

to activate.

NOTE: The amount of water you select will be dispensed. Make sure the container can hold the entire volume. If ice is in the container, you may need to adjust your selection.

2. Touch FAVORITE FILL to turn on, then touch to select

Favorite 1 or Favorite 2. Touch the third time to exit Favorite Fill display.

3. Touch DISPENSE WATER (center button) and the selected

amount of water will be dispensed.

NOTES:

■ The Favorite Fill dispenser will automatically time out after

1 minute of inactivity.

■ You can rell several glasses with the same measurement by

continuing to touch DISPENSE WATER (center button) after each glass ll.

4. Dispense water. NOTE: While dispensing water, the ow of water will

automatically stop once the desired volume has been dispensed.

■ Press a sturdy glass against the dispenser paddle below

the water spout.

■ Place the glass below the water spout, and touch

DISPENSE WATER for hands-free dispensing.

5. To pause dispensing before the selected volume has been

dispensed, touch DISPENSE WATER a second time or touch the water dispenser paddle. Touch DISPENSE WATER or paddle again to resume dispensing remaining amount.

NOTE: If you stop dispensing before the desired volume has been dispensed, the display will turn off after 1 minute. If you have not resumed by then, it will reset back to the original amount.

6. To select a new volume or start dispensing the same volume

again, you must rst nish dispensing the selected volume or turn off the Favorite Fill feature (either by waiting 1 minute so it will automatically turn off or by touching CUBED ICE or CRUSHED ICE to manually turn it off), and then select Favorite Fill again.

The Ice Dispenser

Calibration

Door

Replace

"#$#!

%&#'#(')!"#$#!

Order Filter

a1 oz = b1 L

a2 oz = b2 L

a3 oz = b3 L

Dispense

The Dispenser Drip Tray

IMPORTANT:

■ If the ice cubes are hollow or have an irregular shape, it could

be because of low water pressure. See the “Water Supply Requirements” section.

■ Ice travels from the ice storage bin through the dispenser

chute to the dispenser. To turn off the ice maker, see the “Ice Maker and Storage Bin” section.

■ The dispenser may continue to make noise and ice may

continue to dispense for several seconds after releasing the dispenser button or paddle.

To Clean the Ice Dispenser Chute:

Humidity causes ice to naturally clump together. Ice particles can build up until the ice dispenser chute becomes blocked.

If ice is not dispensed regularly, it may be necessary to empty the ice storage bin and clean the ice delivery chute, the ice storage bin, and the area beneath the storage bin every 2 weeks.

■ If necessary, remove the ice clogging the storage bin and

delivery chute using a plastic utensil.

■ Clean the ice delivery chute and the bottom of the ice storage

bin using a warm, damp cloth, and then dry thoroughly.

To Dispense Ice - Paddle Dispensing

1. Select the desired type of ice by pressing CUBED ICE or

CRUSHED ICE.

WARNING

The drip tray can be removed to carry to the sink to empty or clean.

■ Lift up on the front edge of the tray and pull forward to remove. ■ The drip tray can also slide out to assist in Measured/

Favorite Fill.

The Dispenser Light

1. When you use the dispenser, the light will automatically

turn on.

2. The dispenser light also serves as an automatic night light.

Once the ambient light in the room is reduced, the auto sensor will cause the dispenser light to illuminate.

The Dispenser Lock

Cut Hazard Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

2. Press a sturdy glass against the dispenser paddle. Hold the

glass close to the dispenser opening, so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the paddle to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing. NOTE: Ice may continue to dispense for several seconds after

removing the glass from the dispenser paddle. The dispenser may continue to make noise for a few seconds after dispensing.

The dispenser can be locked for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator or the dispenser light. It simply deactivates the controls and dispenser levers. To turn off the ice maker, see the “Ice Maker and Storage Bin” section.

■ Touch and hold CUBED ICE for 3 seconds to lock the

dispenser.

■ Touch and hold CUBED ICE for 3 seconds to unlock the

dispenser.

■ The display screen indicates when the dispenser is locked.

Ice Maker and Storage Bin

IMPORTANT: To avoid low ice production and poor quality ice, ush the water system before turning on the ice maker. See the “Water Dispenser” section.

■ Following installation, allow 24 hours to produce the rst

batch of ice. Discard the rst 3 batches of ice produced. Allow 2 to 3 days to ll the ice storage bin.

■ The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well-maintained.

■ If the ice in the storage bin clumps together, break up ice

using a plastic utensil and discard. Do not use anything sharp to break up the ice. This can cause damage to the ice bin and the dispenser mechanism.

■ Do not store anything in the ice storage bin.

Style 1 - Ice Maker in the Refrigerator

The ice maker is located on the left door behind the bins. Ice cubes are ejected into the ice storage bin located on the left-hand refrigerator door.

Turn the Ice Maker On/Off

1. Push up on the latch on the left-hand side of the ice

compartment to open the door.

2. Turn on the ice maker by moving the switch to the On (I)

position.

NOTES:

■ To manually turn off the ice maker, move the control to the

Off (O) position.

■ Your ice maker has an automatic shutoff. The sensor will

automatically stop ice production if the storage bin is full, if the door is open, or the storage bin is removed. The control will remain in the On (up) position.

3. Close the ice compartment door. Remove and Replace the Ice Storage Bin

■ Remove the ice storage bin by inserting your ngers into the

hole at the base of the bin and pulling the latch to release the bin from the compartment. Lift the storage bin up and pull it straight out.

■ Replace the storage bin inside the ice compartment and push

down to make sure it is rmly in place.

Ice Production Rate

■ The ice maker should produce approximately 3.2 lbs (1.5 kg)

of ice per day under normal operation.

■ To increase ice production, select the “Max Ice” feature from

the control panel. The ice maker should produce approximately

4.2 lbs (1.9 kg) of ice per day. See the “Using the Controls” section.

Style 2 - Ice Maker in the Freezer (on some models)

Turn the Ice Maker On/Off

To turn the ice maker on, touch Max Ice on the display on the left inner door panel. The icon will blink 3 times and remains lit in the display screen.

To manually turn the ice maker off, touch Max Ice. The display will blink 3 times and turn off.

NOTES:

■ Your ice maker has an automatic shutoff. The sensor will

automatically stop ice production if the storage bin is full or the door is open. The control will remain in the On position.

■ Turn off the ice maker before removing the ice storage bin

to serve ice or to clean the bin. This will keep the ice cubes from dropping out of the ice maker and into the freezer compartment. After replacing the ice storage bin, turn on the ice maker.

Ice Production Rate

■ Your ice maker should produce approximately 3.5 lbs (1.6 kg)

of ice per day under normal operation.

■ To increase ice production, select the “Max Ice” feature from

the control panel. The ice maker should produce approximately

4.6 lbs (2.1 kg) of ice per day. See the “Using the Controls” section.

Shelves, Bins, and Drawers

Fold-Away Glass Shelf

Some shelves will tuck away to create room for taller objects. Some models have 2 fold-away glass shelves.

1. To retract the front section of the shelf, push the adjustable

portion of the shelf as far back as needed toward the rear of the refrigerator.

2. Extend the front glass and front trim of the shelf by pulling the

retracted portion of the shelf outward until it is fully extended.

Wine Rack and/or Pan

Shelves and Shelf Frames

The shelves in your refrigerator are adjustable to meet your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to t different heights of items will make nding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open and save energy.

Shelf Height Adjustment

Shelf height can be adjusted by changing the adjustable shelf mounts between their vertical and horizontal positions.

1. Carefully lift the shelf off the shelf mounts and turn the ipper

to the desired orientation.

2. Repeat for remaining shelf mounts.

3. Apply pressure to the top of the shelf to ensure the shelf is

properly seated on the shelf mounts.

Under one shelf, there are brackets installed to the supports (one bracket on each support). The wine rack or pan rests in these brackets. The wine rack holds 2 bottles without taking up shelf space.

To remove and replace the wine rack:

1. Remove the wine rack/pan by lifting it up off the brackets.

Press the right-hand side of the rack inward until it is free of its bracket. Lower the right-hand side slightly and disengage the left-hand side from its bracket.

2. Replace the wine rack/pan by inserting the left-hand side into

its bracket. Press inward on the right-hand side until it will slide past the bracket edge and set it into its bracket.

Important information to know about glass shelves and covers:

To remove and replace shelves:

1. Make sure adjustable shelf mounts are in the lower position

before removing shelves. Doors will also need to be open at a 90˚ angle. If open wider, it will make it harder to remove the shelves.

2. Remove the middle shelf or top shelf by lifting it up and out

of the shelf supports. Then pull the shelf forward and tilt down to a vertical position. Turn the shelf at an angle and pull out of the refrigerator.

NOTES:

■ You will need to remove middle shelf rst before removing

top shelf.

■ Innity-slide glass shelves should be pushed back in.

When tilted up, make sure glass does not slide to front.

3. Remove the bottom shelf by lifting it up and out of the

shelf supports. Then pull the shelf forward and tilt up to a vertical position. Turn the shelf at an angle and pull out of the refrigerator.

4. Replace the middle and top shelves by putting the shelf in

the refrigerator at an angle with the shelf front down. Lift the front of the shelf up and in until rear shelf drops into the shelf supports. Lower the front of the shelf and make sure that the shelf is in position.

5. Replace the bottom shelf by putting the shelf in the

refrigerator at an angle with the shelf up. Lift the front of the shelf down and in until rear shelf drops into the shelf supports. Lower the front of the shelf and make sure that the shelf is in position.

Shelves with under-shelf lighting (on some models)

By moving LED lighting to a new spot under the shelves, this leading-edge technology improves interior refrigerator lighting and aids in locating storage items.

Pull-Out Platter

To remove and replace Pull-Out Platter: NOTE: Refrigerator doors will need to be removed to remove

platter pocket. See the “Remove and Replace Refrigerator Doors” section for more information.

1. Pull the pull-out platter to the fully open position or when

it stops.

2. Locate the pull-out platter retention clips on both sides.

These are in the side under the pull-out platter.

3. Push the clip up from the bottom with your nger.

4. After both clips have been disengaged, carefully remove

the pull-out platter toward the front of the refrigerator.

To replace crisper(s) cover:

1. Remove the crisper pan, pull-out platter, and crisper glass

before removing the crisper.

2. Fit back of cover frame into supports on side walls of the

refrigerator and lower the front of the cover frame into place.

3. Slide rear of glass insert into cover frame and lower front into

place.

Refrigerator Door Bins

The bins on your refrigerator door are adjustable to meet your individual storage needs. The gallon-sized bins make it easy to customize door storage to hold gallon containers.

Door Bin Divider (on some models)

This divider ts in the door bin to divide the bin and elevate smaller items at the back of the bin.

Humidiseal™ Crisper Drawers

To remove and replace the drawers:

1. Grasp the handle at the bottom of the drawer and slide the

drawer straight out to the stop. Lift the drawer off the bottom guide.

2. Replace the drawer by placing it on the bottom drawer guide

and pushing it past the drawer stop into position.

To remove the crispers cover:

1. Remove the pull-out platter rst.

2. Holding the glass insert rmly with one hand, press up in

center of glass insert until it rises above the plastic frame. Gently slide the glass insert forward to remove.

Herb Tender™ Container

A container to store herbs and the water to keep them fresh is located within the herb bin. For your convenience, you can reposition the Herb Tender™ container anywhere in the bin.

+ 110 hidden pages