JENN-AIR® DETAILED PLANNING DIMENSIONS
G
F
E
A*
D
E
F
H
B
G*
C
A
G
F
E
A*
B*
C*
H
I
D*
30" ELECTRIC DOWNDRAFT RANGE
JES1750F – 297⁄8" x 36" x 285⁄16"
PRODUCT DIMENSIONS
1 of 4
FRONT VIEW
A
C
MODEL # JES1750F
in cm
D
E
F
G*
H
Overall width 297⁄8 75.9
A
Width of door
B
Height from cooktop to top of vent 13⁄16 3.0
C
Space between door and face panel
D
Height to top of handle
E
Height of door
F
Height to top of cooktop edge 36 91.4
*G*
Space between door and bottom panel
H
Depth from front of console to back of range (max.) 2713⁄16 70.7
I
Depth from handle to back of range (max.) 285⁄16 71.9
J
* With leveling legs screwed all the way in. Range can be raised approximately
1" (2.5 cm) by adjusting the leveling legs.
297⁄8 75.9
13
⁄16 2.1
227⁄8 58.1
231⁄4 59.0
13
⁄16 2.0
B
A
TOP VIEW
I
J
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation or Use & Care Guide
before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8894A A d Zw1116
JENN-AIR® DETAILED PLANNING DIMENSIONS
D
E
F
H
B
G*
C
A
I
J
A
G
F
E
A*
B*
C*
H
I
D*
30" ELECTRIC DOWNDRAFT RANGE
JES1750F – 297⁄8" x 36" x 285⁄16"
2 of 4
DIMENSIONS AS INSTALLED
A*
SIDE VIEW
E
B*
C*
MODEL # JES1750F
F
G
Height to top of cooking surface (min.) 351⁄2 90.2
A*
Height to top of door (min.) 3011⁄16 78.0
B*
Height to top of handle (min.) 301⁄2 77.5
C*
Height to top of countertop (min.) 3513⁄16 91.0
D*
Depth with door fully open 509⁄16 128.5
E
Depth with handle 285⁄16 71.9
D*
H
I
F
Depth without handle 2713⁄16 70.7
G
Depth without door 25 63.5
H
Depth with door 265⁄16 66.8
I
Height of countertop channel 113⁄16 4.6
J
Depth to countertop channel 13⁄16 3.0
K
* With leveling legs screwed all the way in. Range can be raised
approximately 1" (2.5 cm) by adjusting the leveling legs.
in cm
SIDE VIEW – COUNTERTOP CHANNEL DETAIL
J
K
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation or Use & Care Guide
before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8894A A d Zw1116
JENN-AIR® DETAILED PLANNING DIMENSIONS
Side
Cabinet
L
BB
v
‡
v
‡
M
v
‡v‡
M
G
F
E
H
I
D*
3 of 4
30" ELECTRIC DOWNDRAFT RANGE
JES1750F – 297⁄8" x 36" x 285⁄16"
OPENING/CLEARANCE DIMENSIONS
MODEL # JES1750F
in cm
Width of combustible area above
A
cooking surface (min.)
Width from cooktop to fixed wall
B
A
H*
I
D E
C C
†
†
e
e
v
v
GG
FRONT VIEW
J
J FF
K
or other combustible material (min.)
Width from electrical installation area
C
to cabinet (min.)
Width from vent installation area
D
to left side of cabinet (min.)
Width from vent installation area
E
to right side of cabinet (min.)
Height of center of rear wall vent installation
F
area (max)
Height of sides of rear wall vent installation
G
area (max)
Height to bottom of uncovered wood or
H*
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
I
or metal cabinet (min.)
Height of electrical installation area (max.)
J
Depth of electrical installation area (max.)
K
Depth of upper cabinet (recommended)
L
Width of cutout
M
e
Recommended junction box location (within shaded dashed line area)
Recommended rear wall venting location (within patterned solid line
†
v
area) – see page 4 for ducting information
Refer to template number W10817089B – see page 4 for
‡
v
ducting information
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is
covered by not less than 1⁄4" (0.6 cm) flame retardant millboard covered with not less
than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
30 76.2
3 7.6
413⁄16 12.2
12 30.5
8 20.3
71⁄2 19.0
51⁄2 14.0
30 76.2
18 45.7
711⁄16 19.5
311⁄16 9.4
13 33.0
30 76.2
ELECTRICAL REQUIREMENTS
Side
Cabinet
L
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation or Use & Care Guide
before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
240 volt, 60 Hz, AC only, 40-amp fused, grounded circuit is required.
A dedicated circuit is recommended. Minimum length of power cord
is 48" (121.9 cm).
‡
v‡v
M
BACK VIEWSIDE VIEW TOP VIEW – CUTOUT
8894A A d Zw1116
JENN-AIR® DETAILED PLANNING DIMENSIONS
5" (12.7 cm) diameter
diameter duct
DOWNDRAFT RANGE DUCTING ARRANGEMENTS
4 of 4
DUCTING CONFIGURATIONS
to 31⁄41" x 10"
5" (12.7 cm)
diameter duct
REAR DUCTING IN WALL TO ROOF
5" (12.7 cm)
REAR DUCTING THROUGH WALL TO OUTSIDE
(8.3 cm x 25.4 cm)
transition elbow
5" (12.7 cm)
diameter wall cap
DUCTING REQUIREMENTS
RANGE DUCT LENGTH DUCT SIZE
10' (3.0 m) or less*
Dual Fuel
Between 10' (3.0 m)
and 60' (18.3 m)
10' (3.0 m) or less**
Electric
Between 10' (3.0 m)
and 60' (18.3 m)
* Dual fuel ranges must use 5" (12.7 cm) diameter for runs of 10' (3.0 m)
or less.
** May be used to vent straight out the back of the range and directly
through the wall.
CALCULATING MAXIMUM DUCTING LENGTH
• Maximum ducting length is 60' (18.3 m).
• Each 90° elbow equals 5' (1.5 m) duct.
• Use no more than three 90° elbows.
• Flexible metal vent is not recommended.
• Do not install two elbows together.
NOTES:
• For ducting runs up to 30' (9.1 m), install range as shipped.
• For ducting runs of 31' (9.4 m) to 60' (15.2 cm), remove the
restricter ring on the blower inlet housing.
• For altitudes above 4500' (1272.0 m), reduce recommended
vent run by 20% for best performance.
5" (12.7 cm)
diameter*
6" (15.2 cm)
diameter
31⁄4" x 10"
(8.3 cm x 25.4 cm)
5" (12.7 cm)
diameter**
6" (15.2 cm)
diameter
31⁄4" x 10"
(8.3 cm x 25.4 cm)
5" (12.7 cm)
to 6" (15.2 cm)
diameter
transition elbow
6" (15.2 cm)
THROUGH FLOOR BETWEEN JOISTS TO OUTSIDE
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation or Use & Care Guide
before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
diameter wall cap
DUCT-FREE INSTALLATION THROUGH RANGE FRONT
8894A A d Zw1116
Loading...