Jenn-Air JER8885RAS16 Installation Instruction

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE

INSTALLATION MANUAL

Electric 30-inch Wide

Free -standing Range

PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE

THE MANUAL IS INTENDED TO ASSIST IN THE INITIAL INSTALLATION AND ADJUSTMENTS OF THE RANGE.

CLEARANCE DIMENSIONS

SPECIAL WARNING

Only qualified personnel should
install or service this range.

For complete information in regard to installation of
freestanding range, see figures 1 and 2 on page 2. For
SAFETY CONSIDERATIONS do not install a range in
any combustible cabinetry which is not in accord with the
installation clearances shown in figure 1.

Read “Safety Instructions” in Use &
Care book before using range.

Improper installation, adjustment,
alteration, service, maintenance or
use of range can result in serious
injury or property damage.

CAUTION: This range has been designed in

accordance with the requirements of various safety
agencies and complies with the maximum allowable
wood cabinet temperatures of 194°F. If this range is
installed with cabinets that have a lower working
temperature than 194°F, discoloration, delamination
or melting may occur.

ENGLISH '''' PP. 1-7
ESPAÑOL '''' pág. 8-14
FRANÇAIS '''' p. 15-21

MOBILE HOMES

The installation of a range designed for mobile home
installation must conform with the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part
3280 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24 HUD, Part 280) or,
when such standard is not applicable, the Standard for
Manufactured Home Installations 1982 (Manufactured
Home Sites, Communities and Set-Ups), ANSI
A225.1-latest edition, or with local codes.

LOCATING THE RANGE

Place range in a well lit area. Do not set range over
holes in the floor or other locations where it may be
subject to strong drafts. Any opening in the wall behind
the range and in the floor under the range should be
sealed. Make sure the flow of cooling/ventilation air is
not obstructed below the range.

Your range may not be equipped with some of the features referred to in this
manual.

8101P506-60

(08-03-01)

INSTALLATION DRAWINGS

IMPORTANT

PLEASE KEEP FOR THE USE OF THE
LOCAL ELECTRICAL INSPECTOR.

4

3

1

“A”

2

FIGURE 1

NOTE: Figure may not be representative of actual unit.

“A” = 30 inches (76.2 cm) minimum clearance between the
top of the cooking surface and the bottom of an unprotected
wood or metal cabinet, or “A” = 24 inches (61 cm) minimum
when bottom of wood or metal cabinet is protected by not
less than 1/4-inch (6.4 mm) thick flame-retardant millboard
covered with not less than No. 28 MSG sheet steel,

0.015-inch (0.381 mm) thick stainless steel, 0.024-inch
(0.610 mm) thick aluminum, or 0.020-inch (0.508 mm) thick
copper.

To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5 inches (13
cm) beyond the bottom of the cabinets.

FIGURE 1

1, 2, 3 - COMBUSTIBLE BUILDING WALLS.

4 - COMBUSTIBLE WALL CABINET.

A free-standing range may be installed adjacent to (0²
from) combustible walls 1, 2 & 3.

NOTE: FOR INSTALLATION IN CANADA, A
FREE-STANDING RANGE IS NOT TO BE INSTALLED
CLOSER THAN 12MM FROM ANY ADJACENT
SURFACE.

FIGURE 2

-2-

ANTI-TIP DEVICE INSTALLATION INSTRUCTIONS

WARNING: A risk of range tip-over exists if the appliance

is not installed in accordance with the provided installation
instructions. The proper use of this device minimizes the
risk of TIP-OVER. In using this device the consumer must
still observe the safety precautions as stated in the USE
and CARE MANUAL and avoid using the oven door
and/or lower drawer as a step stool.

Installation instructions are provided for wood and cement
in either floor or wall. Any other type of construction may
require special installation techniques as deemed
necessary to provide adequate fastening of the ANTI-TIP
bracket to the floor or wall. The bracket may be installed
to engage the left or right rear leveling foot.

STEP 1 - Locating The Bracket (See Figure 3)

A. Determine where either the right or left “EDGE” of the

range will be located and mark the floor or wall.

B. Place the BRACKET 9/16² (14.5 mm) from the

marked “EDGE” toward center of opening and against
the back wall, as shown in figure 3, with orientation
hole against wall.

C. Use the bracket as a template and mark the required

holes, as shown in figure 3 for the type of construction
you will be using.

D. Free-standing range may be secured to either floor or

wall.

STEP 2 - Anti-Tip Bracket Installation

Options

A. Wood Construction:

1. Floor: Locate the center of the two holes identified
in figure 3 as “HOLES FOR FLOOR”. Drill a 1/8²
(3 mm) pilot hole in the center of each hole (a nail
or awl may be used if a drill is not available).
Secure the ANTI-TIP bracket to the floor with the
two screws provided. Proceed to Step 3.

2. Wall: Locate the center of the two holes identified
in figure 3 as “HOLES FOR WALL”. Drill an
angled 1/8² (3 mm) pilot hole in the center of each
hole as shown in figure 4. (A nail or awl may be
used if a drill is not available). Secure the
ANTI-TIP bracket to the wall with the two screws
provided as shown in figure 4. Proceed to STEP

3.

B. Cement or Concrete Construction:

1. Suitable screws for concrete construction can be
obtained at the hardware store. Drill the required
size hole for the hardware obtained into the
concrete at the center of the holes identified in
figure 3 as “HOLES FOR FLOOR”. Secure the
ANTI-TIP bracket to the floor. Proceed to STEP

3.

FIGURE 3

-3-

ANTI-TIP DEVICE INSTALLATION INSTRUCTIONS

STEP 3 - Range Installation

A. For safety considerations as well as optimum

performance, adjust the range so it is level and to
desired height prior to installing in cabinet opening.

Levelness may be checked by placing a spirit level or a
largepanofwateron thecooktopor ovenrack.Adjustthe
rangeby tipping it forward or back and rotate the leveling
feet as required.

Note: A minimum clearance of 1/4² (6mm) is required
between the range andthe leveling foot that will engage
the anti-tip bracket, (see figure 4).

Caution: Damage to the range may occur if range is
moved or lifted by grasping the main top, backguard or

door handle. All free-standing ranges with a glass top
have a non lift-up top. Coil tops are lift-up.

B. Align the range to its designated location and prepare

to slide it back into position. Connect power cord and
plug into outlet following guidelines outlined in
connecting the range.

C. Slide range into place visually inspecting to verify that

power cord is freely routed and contained behind
range.

D. To check the range for proper installation of the anti-tip

bracket, use a flashlight and look underneath the
bottom of the range to see that one of the rear leveling
feet is engaged in the anti-tip bracket slot.

NOTE: USE A MINIMUM OF (2) SCREWS TO

INSTALL ANTI-TIP BRACKET TO THE
WALL OR FLOOR.

FIGURE 4

-4-

CONNECTING THE RANGE

ELECTRIC SUPPLY

The range must be installed in accordance with Local and
National Electric Code (NEC) ANSI/NFPA No. 70-latest
edition. See rating plate for total connected KW rating.

ELECTRIC SUPPLY (Canada)

The range must be installed in accordance with Local and
Canadian Electric Code CSA STD.C22.1 latest edition.
See rating plate for total connected KW rating.

OUTSIDE WIRING

Your local utility company will tell you whether the present
electric service to your home is adequate. It may be
necessary to increase the size of the wiring to the house
and service switch to take care of the electrical load
demanded by the range. The kilowatt rating for the range
is specified on the rating plate located on front of range.

HOUSE WIRING

Most local Building Regulations and Codes require that all
electrical wiring be done by licensed electricians. All
wiring should conform to Local and National Electrical
Codes. This range requires a single phase three wire
120/240 or a 120/208 volt, 60 Hz, AC circuit. Wiring codes
require a separate circuit be run from the main entrance
panel to the range and that it be equipped with separate
disconnect switch and fuses, either in the main entrance
panel or in a separate switch and fuse box. In some
communities, a solid or flexible continuous armored
conduit must be used from main entrance panel to the
terminal box on the rear of the range. Others will permit
the termination of the range circuit at a polarized three or
four wire plug-in outlet placed at a convenient point near
the back of the range. The range is then connected to this
outlet through an approved range connector (pigtail)
fastened securely to the terminal block with proper strain
relief at the range and a three or four pronged plug at the
opposite end.

by local code. USE COPPER OR ALUMINUM
CONDUCTORS. Main terminal block is recognized for
Copper or Aluminum conductors. If a flexible power cord
is required, it is recommended a cord no longer than 4 ft.
be used. Make connections as explained below and with
reference to the appropriate illustration (see figures 6 and

7). After installation, insure tightness of all electrical
connections and replace all covers.

Remove terminal block access cover from range back.
(See figure 5).

RANGE CONNECTIONS (Canada)

This model was shipped direct from the factory with
service cord (pigtail) attached. There are no range
connections necessary. Just plug into the range outlet.
See figure 2 on page 2 for outlet location.

NOTE: Cord replacement - ONLY a power supply cord
rated at 240 volts minimum, 40 amperes or 50 amperes
power supply cord that is marked for use with nominal
13/8² (34.93 mm) diameter connection opening, with
closed loop terminals and marked for use with ranges
shall be used.

RANGE CONNECTIONS

Some models are shipped direct from the factory with
service cords (pigtails) attached. There are no range
connections necessary on these models. Just plug into
the range outlet. On models not provided with a service
cord, connection to the power supply is necessary.
REMEMBER - only a 4-conductor cord is to be used on
new branch-circuit installations (1996 NEC), mobile
homes, recreational vehicles, or in an area where local
codes prohibit grounding through the neutral conductor.
Hence, 4-wire service MUST be provided for such
installations. 3-wire service may be used when permitted

FIGURE 5

-5-

CONNECTING THE RANGE

FIGURE 6
3-Wire Service Cord or Conduit Installation

1. Insure that the copper ground strap IS CONNECTED
between the middle post of the main terminal
connection block and the range chassis.

2. If bare copper or aluminum wiring is used, attach
adapter lugs as shown in figure 6. (See Bare Wire
Connection). Torque specifications are shown below.

post of the main terminal block. The other two wires of
the service cord or conduit connect to the outside
posts of the main terminal connection block. Polarity is
unimportant. If using bare wire, attach wire to
appropriate lug as shown. Torque specifications are
shown below.

3. The middle wire of the service cord or ground lead of
3-wire conduit MUST connect to the neutral (middle)

ACCEPTABLE - 3 WIRE PLUG INSTALLATION

4. An appropriate strain relief for service cord or conduit
MUST be attached to the conduit plate.

FIGURE 6

-6-

CONNECTING THE RANGE

FIGURE 7
4-Wire Service Cord or Conduit Installation

(Mobile Homes Or As Required By Codes)

1. The copper ground strap connected between the
neutral (middle) post of the main terminal block and the
chassis MUST be cut off as shown in figure 7. Save the
green ground screw to attach the ground from the 4
wire cord. Only a 4 wire cord or conduit should be
used.

2. If bare copper or aluminum wiring is used, attach
adapter lugs as shown in figure 7. (See Bare Wire
Connection). Torque specifications are shown below.

3. The ground wire from the service cord or conduit must
connect to the range chassis using the green ground
screw.

4. The white wire of the service cord or conduit must
connect to the neutral (middle) post of the main
terminal block. The other two wires of the service cord
connect to the red and black posts of the main terminal
block, respectively. If using bare wire, attach wire to

appropriate lug as shown. Torque specifications are
shown below.

5. An appropriate strain relief for service cord or conduit

MUST be attached to the conduit plate.

Conversion From 3-Wire To 4-Wire Service

(Free-standing Model With 3-Wire Service Cord
Attached).

Disconnect range from power. Remove the access cover
on back of range and remove the 3-wire service cord from
the main terminal block. Follow instructions as outlined in
figure 7 to connect the 4-wire service cord.

NOTE: Cord replacement - ONLY a power supply cord
rated at 240 volts minimum, 40 amperes or 50 amperes
power supply cord that is marked for use with nominal 1
3/8² (34.93 mm) diameter connection opening, with
closed loop terminals and marked for use with ranges
shall be used.

ACCEPTABLE - 4 WIRE PLUG INSTALLATION

FIGURE 7

-7-