Jenn-Air JEI0430ADS0, JEI0536ADS0 Installation Guide

30" (76.2 CM) AND 36" (91.4 CM) ELECTRICCOOKTOP

INSTALLATIONINSTRUCTIONS

INSTRUCTIONS.D'INSTALLATIONDE LA

TABLEDECUISSON ELECTRIQUEDE30" (76,2 CM)

ETDE36" (91,4 CM)

TableofContents/Table desmati@res

COOKTOP SAFETY ........................................................................ 1

INSTALLATION INSTRUCTIONS .................................................. 2

Tools and Parts ............................................................................ 2

Location Requirements ................................................................ 2

Electrical Requirements .............................................................. 3

Install Heat Shield ......................................................................... 3

Install Foam Strip ......................................................................... 4

Install Cooktop ............................................................................. 4

Make Electrical Connection ......................................................... 5

Attach Cooktop to Countertop .................................................... 6

Complete Installation ................................................................... 6

COOKTOP SAFETY

SECURIT¢: DE LA TABLE DE CUISSON ...................................... 7

INSTRUCTIONS D'INSTALLATION ............................................... 7

Outillage et pieces ........................................................................ 7

Exigences d'emplacement ........................................................... 7

Specifications electriques ........................................................... 9

Installation de I'ecran thermique .................................................. 9

Installation de la bande de mousse ........................................... 10

Installation de la table de cuisson .............................................. 10

Raccordement electrique ........................................................... 11

Fixation de la table de cuisson au plan de travail ...................... 12

Achever I'installation .................................................................. 12

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iMPORTANT:

Save for local electrical inspector's use.

iMPORTANT :

,&,conserver pour consultation par I'inspecteur local des installations electriques.

W10098720

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here,

Tools needed

• Tape measure • Marker or pencil

• Flat-blade screwdriver • Pliers

• Phillips head screwdriver • 14"drill bit

• Hand or electric drill • Jigsaw

• Level

Parts supplied

• Clamping brackets (2)

• 2W' (6.4 cm) clamping screws (4) and washers (4)

• #8 x %" (9.5 mm) sheet metal screws (4)

• Heat shield (attached to the cooktop base for shipping) Parts needed

• A UL listed or CSA approved strain relief

• ULlisted wire connectors Check local codes. Check existing electrical supply. See

"Electrical Requirements." All electrical connections should be made by a licensed, qualified

electrical installer.

Product Dimensions

A.21%_"(54.6 cm) B.31" (78.7 cm) on 30" (76.2 cm) models

87" (94cm)on 36" (91.4 cm) models

C.3_2" (7.9 cm) D.Model/serial rating plate (located on

underside of cooktop base in the right front corner)

Cabinet Dimensions

Make sure you have everything needed for correct installation. It is the responsibility of the installer to comply with the installation

clearances specified in these instructions. IMPORTANT: Observe all governing codes and ordinances. When

installing cooktop, use minimum dimensions given.

• To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinets.

• Check the cooktop base for an approved installation label. Verify approved oven model numbers that can be installed

with your cooktop model number. If you do not find this label, your cooktop may not be approved for use over an undercounter built-in oven. Contact your dealer to confirm

that your cooktop is approved.

• Ovens approved for this type of installation will have an approval label located on the top of the oven. If you do not find this label, contact your dealer to confirm that your oven is approved. Refer to oven manufacturer's Installation

Instructions for approval for built-in undercounter use and proper cutout dimensions.

• When installing cooktop over an undercounter built-in oven, do not fasten cooktop to countertop with clamps or seal

cooktop to countertop. This will make the cooktop easier to remove if future servicing becomes necessary.

• Use the countertop opening dimensions that are given with these Installation Instructions. Given dimensions are minimum

clearances and provide 0" (0 cm) clearance.

• Grounded electrical supply is required. See "Electrical Requirements" section.

A. 30" (76.2 cm) on 30" (76.2 cm) models

36" (91.4 cm) on 36" (91.4 cm) models

B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of unprotected wood or metal cabinet (24" [61 cm] minimum clearance if bottom of wood or metal cabinet is protected by not less than V/' [0.6 cm] flame retardant mlllboard covered with

not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless

steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)

D. !3" (33 cm) recommended upper cabinet depth

E.2" (5.1cm) F. 20_/2" (52 cm)

G. 18" (45. 7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop

H. Junction box or outlet," 12" (30.5 cm) minimum from bottom of

countertop

I.Junction box or outlet," 10" (25.4 cm) from right-hand side of cabinet

J. 297/2" (74.9 cm) on 30" (76.2 cm) models

357/;'' (90.2 cm) on 36" (91.4 cm) models

K. 1" (2.5 cm) minimum distance to nearest left and right side

combustible surface above cooktop

L. 1" (2.5 cm) minimum clearance between back wall and countertop

NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear

the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout.

If cabinet has a drawer, a 51/s''(13 cm) depth clearance from the countertop to the top of the drawer (or other obstruction) in base

cabinet is required. If installing a hood above the cooktop, follow hood instructions for

dimensional clearances above the cooktop surface.

• A UL listed or CSA approved conduit connector must be provided at each end of the power supply cable (at the

cooktop and at the junction box). A listed conduit connector is already provided at the cooktop.

• If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

sS, H®{/s'S ed

Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper wire.

Electrically ground cooktop. Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local codes.

Check with a qualified electrical installer if you are not sure the cooktop is properly grounded.

It is not recommended to have a fuse in the neutral or ground circuit.

Make sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code,

ANSl/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-1atest

edition, and all local codes and ordinances. A copy of the above code standards can be obtained from:

National Fire Protection Association One Batterymarch Park

Quincy, MA 02269 CSA International 8501 East Pleasant Valley Road

Cleveland, OH 44131-5575 Before You Make the Electrical Connection:

To properly install your cooktop, you must determine the type of electrical connection you will be using and follow the instructions

provided for it here.

• A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only electrical supply is required on a separate, 50-amp circuit [36" (91.4 cm) models] or 40-amp circuit [30" (76.2 cm)

models], fused on both sides of the line.

• The cooktop should be connected directly to the junction box through flexible, armored or nonmetallic sheathed, copper

cable. The flexible, armored cable extending from the fuse box or circuit breaker box should be connected directly to the

junction box.

• Locate the junction box to allow as much slack as possible between the junction box and the cooktop so that the cooktop

can be moved if servicing becomes necessary in the future.

• Do not cut the conduit. The length of conduit provided is for serviceability of the cooktop.

Excessive Weight Hazard

Use two or more people to move and install cooktop. Failure to do so can result in back or other injury.

1. Decide on the final location for the cooktop.

2. Using 2 or more people, place the cooktop upside down on a covered work surface.

3. Remove the heat shield from the cooktop. Set the 2 screws aside for reattaching the heat shield.

A ...................',

L 1................ "_

A. Heat shield

B. Removescrews

4. Using 2 screws, reattach the heat shield to the underside of the cooktop at the predrilled holes as shown in the following

illustration.

A. Heat shield B. Predrilled holes

Remove foam strip from literature packing.

Remove backing from foam strip.

Apply foam strip adhesive-side down around bottom of cooktop, flush with edge.

NOTE: The foam strip protects the underside of the eooktop glass from debris and helps the eooktop sit flat on uneven

counters.

A.Cooktop base B.Foam strip

C.Glass

Style I: Oooktop over undercounter built-in oven

IMPORTANT:

• Your cooktop may not be approved for use over an

undercounter built-in oven, Contact your dealer to confirm that your cooktop is approved for such use.

• Clamping brackets should not be used.

1. Turn cooktop right side up.

2. Place cooktop in cutout. NOTE: Make sure that the front edge of the cooktop is parallel

to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the

countertop.

Style 2: Cooktop over cabinets

1. Determine whether your cabinet construction provides clearance for installing clamping brackets at cooktop base

ends. This is the recommended location. Clamping brackets can be installed on the back of cooktop base bottom, if

necessary,

Installing Brackets Before Placing Cooktop in Cutout

1. Position bracket to allow the clamping bracket to extend far

enough out from the cooktop for the installation of 21/2'' (6.4 cm) clamping screws. See "Attach Cooktop to Countertop" for illustration of clamping screw installation.

A. Clamping bracket

B.Attachment screw and washer

C. Clamping screw

2. Rotate brackets so they do not extend beyond edge of cooktop base.

3. Tighten screws enough to hold brackets in place when cooktop is placed into the cutout,

4. Turn the cooktop right side up and place in cutout. NOTE: Make sure that the front edge of the cooktop is parallel

to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.

5. Loosen the screws and rotate the brackets so that they are perpendicular to the edge of the cooktop base and extend beyond its edge. Securely tighten screws.

Installing Brackets After Placing Cooktop in Cutout

1. Place cooktop in cutout. NOTE: Make sure that the front edge of the cooktop is parallel

to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop,

2. Position clamping bracket to allow the bracket to extend far enough out from the cooktop for the installation of 21/d' (6.4 cm) clamping screws,

A.Attachment screw holes, side or back locations B. Front of cooktop

The clamping brackets can be installed before or after the cooktop is placed into the cutout. Complete the following steps for the option you choose.

A. Glass cooktop B. Cooktop base

C. Attachment screw D. Clamping bracket (extends

far enough beyond cooktop base to allow installation of

clamping screws)

E.2_2" (6.4 cm) clamping screw

(to be installed in "Attach Cooktop to Countertop" section)

F Countertop

G. Foam seal

3. Attach brackets to cooktop base bottom with bracket attachment screws using the bracket mounting holes,

Securely tighten screws,

+ 8 hidden pages