Jenn-Air MDB4409PAW2, MDB4409PAS2, MDB4409PAB2, JDB8700AWS3, JDB8700AWS2 Owner’s Manual

...

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered inTROUBLESHOOTING,

please visit our website at www.jennair.com for additional information. If you still need assistance, call us at 1-800-688-1100. In

Canada, visit our website at www.jennair.ca or call us at 1-800-807-6777. You will need your model and serial number located near the door on the right-hand or left-hand side of the dishwasher interior.

Table of Contents

DISHWASHER SAFETY ............................................................. 1

WHAT'S NEW IN YOUR DISHWASHER ................................... 3

PARTS AND FEATURES ............................................................ 4

START-UP / QUICK REFERENCE ............................................ 5

QUICK STEPS ............................................................................ 6

DISHWASHER USE .................................................................... 6

CYCLE AND OPTION DESCRIPTIONS .................................... 8

DISHWASHER FEEDBACK SECTION .................................... 11

DISHWASHER FEATURES ...................................................... 11

FILTRATION SYSTEM ............................................................. 14

DISHWASHER CARE ............................................................... 15

TROUBLESHOOTING .............................................................. 16

WARRANTY .............................................................................. 19

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

W10596272A

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: When using the dishwasher, follow basic precautions, including the following:

[] Read all instructions before using the dishwasher. [] Do not tamper with controls. [] Use the dishwasher only for its intended function. [] Use only detergents or rinse agents recommended for use in

a dishwasher, and keep them out of the reach of children.

[] When loading items to be washed:

1) Locate sharp items so that they are not likely to damage the door seal; and

2) Load sharp knives with the handles up to reduce the risk of cut-type injuries.

[] Do not wash plastic items unless they are marked

"dishwasher safe" or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

[] Do not touch the heating element during or immediately after

use.

[] Do not operate the dishwasher unless all enclosure panels

are properly in place.

[] Do not abuse, sit on, or stand on the door, lid, or dish racks

of the dishwasher.

[] To reduce the risk of injury, do not allow children to play in

or on the dishwasher.

[] Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using the dishwasher turn on all hot water faucets and let the

water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable,

do not smoke or use an open flame during this time.

[] Remove the door or lid to the washing compartment

when removing an old dishwasher from service or discarding it.

SAVE THESE iNSTRUCTiONS

GROUNDING iNSTRUCTiONS

[]

For a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for electric current. The dishwasher is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet

that is installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

if you are in doubt whether the dishwasher is properly grounded. Do not modify the plug provided with the dishwasher; if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

For a permanently connected dishwasher: The dishwasher must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on the dishwasher.

SAVE THESE iNSTRUCTiONS

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Congratulationsonpurchasingyourwaterandenergyefficientdishwasher!Thisdishwashercleansbysprayingthe disheswithwaterandpausestoallowthedetergenttosoakintoandreleasethesoilsonthedishes.Thecyclesare longerduetothesoakandpausesforexceptionalcleaning.Severalmodelscontainanopticalwatersensor.The

opticalwatersensorisusedtodeterminetheoptimumwaterandenergyconsumptionforgreatcleaning performance.Efficientdishwashersrunlongertosavewaterandenergy,justasdrivingacarslowersavesongas.

Thefirstcycleusingthesensorwillrunlongertocalibratetheopticalsensor.

Usingrinseaidwilloptimizeyourdryingandwashperformance. Thisdishwasherisspecificallydesignedtobeusedwithrinseaid

forimproveddryingperformanceandcontrollingbuildupofhard waterdeposits.Energyefficientdishwashersuselesswaterand

energy,sotheydependonthewater"sheeting"actionofrinse aidfortotaloptimalperformance.

Detergent

The United States has passed a restriction limiting the amount of phosphorus (phosphates) in the household dishwasher

detergents to no more than 0.5%, where previous detergents contained 8.7%. Major manufacturers have reformulated their

dishwasher detergent for this change in detergents as another step in eco-conscious awareness. With these recent changes it is

recommended to use tablets and packs for convenience and improved performance.

Your dishwasher has the latest technology in dishwasher filtration. This triple filtration system minimizes sound and

optimizes water and energy conservation while providing optimal cleaning performance. Maintenance of your filters regularly will

sustain peak cleaning performance. We suggest you clean both your upper and lower filter and rinse under running water at least

once a month.

Upper level wash ...................................................................................................................................................................................._-! ....................................................................................

Water feed tube

Model and serial number label Water inlet opening

Rinse aid dispenser reduces spotting

and improves drying.

Detergent dispenser .......................................................................................................................................................................

Premium top rack adjusters (on some models

Pressurized spray nozzles and variable speed motor provide effective cleaning.

Filtration System removes soil from water and improves cleaning action.

...........................................................................................................................................................................................................Control panel

Culinary tool rack/3rd level rack

(on some models)

Cup shelves with

stemware holder

Flexible fold-down tines (on some models)

Upper spray arm ................................................................................................................................................................................................................................................................................................................................................................................

(on some models)

TOP RACK

Flexible fold-down tines

Silverware basket

BOTTOM RACK

IMPORTANT: Do not block detergent dispenser. Sensor Wash cycle for optimal cleaning

Tall items placed in the lower rack may block the dispenser

door. Cookie sheets and cutting boards loaded on the

left-hand side of the dishwasher can easily block

the dispenser. If detergent is inside of the dispenser or on

the bottom of the tub after the cycle is complete, the

dispenser was blocked.

Drying - Rinse Aid is essential,

You must use a drying agent such as rinse aid for good

drying performance (sample included). Rinse aid along

with the Precision Dry®or Precision Dry®+ option will

provide best drying and avoid excessive moisture in the

dishwasher interior.

1 Hour Wash 'When you need fast results.

High Efficiency dishwashers run longer to save water and energy just as driving a car

slower saves on gas. When you need fast results, the 1 Hour Wash will clean your

dishes using slightly more water and energy. For improved drying, select the Precision Dry®

or Precision Dry®+ option to add additional time to dry.

The most advanced and versatile cycle.

Sensor Wash cycle senses the load size, soil

amount, and toughness of soil, to adjust the

cycle for optimal cleaning using only the

amount of water and energy needed. The

Sensor Wash and Heavy Wash cycles are

recommended for tough soil. No need to

prerinse dishes; just scrape and load.

Press START/RESUME every time you add a dish.

IMPORTANT: If anyone opens the door (such

as, adding a dish, even during the Delay

Hours option), the Start/Resume button must

be pressed each time.

If the Start/Resume button is located on top of

Repeat Last Cyde

door: Push door firmly closed within

3 seconds of pressing START/RESUME. If the

door is not closed within 3 seconds, the start

button LED will flash, an audible tone will be

heard, and the cycle will not start.

It is possible to use too much detergent in your dishwasher. This can lead to etching of your dishes. See "Add Detergent"

and "Add Rinse Aid" sections to determine the amount of

detergent needed based on your water hardness. Using

dishwasher detergent tablets and packs have been proven

better than powder, liquid or gel detergents to reduce filming

on your dishes.

Prepare and load dishwasher.

Spin the spray arms. They

should turn

freely.

Select a cycle and option (cycles and options vary by model.)

CYCLES

OPTIONS

Sound Ott/O_ - 3 Sec Hold _ Sec

Add detergent

and rinse aid.

......ii:::i' Ai;:i _::: ::7i I ::,:::

Prepare and Load the Dishwasher IMPORTANT: Remove leftover food, bones, toothpicks and other

hard items from the dishes. Remove labels from containers before washing.

lO place load - upper rack 10 place load - lower rack

12 olace load - upper rack 12 place load - lower rack

_ Start dishwasher.

NOTE: Push door firmly closed within

3 seconds of pressing START/

Repeat L_t Cycle

RESUME. If door is not closed within

3 seconds, the Start indicator will flash, an audible tone will be heard, and the cycle will not start.

• Make sure nothing keeps spray arm(s) from

spinning freely. It is important for the water spray to reach all soiled surfaces.

• Make sure that when the dishwasher door is closed no items are blocking the detergent dispenser.

• Items should be loaded with soiled surfaces facing down and angled toward the spray. This will improve cleaning and drying

results.

• Avoid overlapping items like bowls or plates that may trap food.

• Place plastics, small plates and glasses in the upper rack. Wash only plastic items marked "dishwasher safe."

• To avoid thumping/clattering noises during operation: Load dishes so they do not touch one another. Make sure lightweight

load items are secured in the racks. Improper loading can cause dishes to be chipped or damaged.

When loading glasses or mugs, it is best to load these items in between rows of tines instead of loading them over tines, as

shown. When loading silverware, always place sharp items pointing

down. Mix items in each section of the basket with some

pointing up and some down to avoid nesting. Spray cannot

reach nested items.

STEP 2

Add Detergent

NOTE: If you do not plan to run a wash cycle soon, run a rinse

cycle. Do not use detergent.

• Use automatic dishwasher detergent only. Add detergent just before starting a cycle.

Fresh automatic dishwasher detergent results in better

cleaning. Store tightly closed detergent container

in a cool, dry place.

Check the rinse aid indicator. Add rinse aid when indicator drops to "Add" level.

To add rinse aid, turn the dispenser cap to "Refill"

and lift off. Pour rinse aid into the opening until the

indicator level is at "Full." Replace the dispenser

cap and turn to "Lock." Make sure cap is fully

locked.

NOTE: For most water conditions, the factory setting of 3 will give good results. If you have

hard water or notice rings or spots, try a higher setting. Turn the arrow adjuster inside the

dispenser by either using your fingers or inserting a flat-blade screwdriver into the center

of the arrow and turning.

Premeasured Detergents

Many detergents now come in premeasured forms (gel packs,

tablets, or powder packs). These forms are suitable for all hardness and soil levels. Always place premeasured detergents in main

compartment and close lid.

Using dishwasher detergent tablets and packs have been proven better than powder, liquid or gel detergents at reducing filming on

dishes. Using tablets and packs over time will start to reduce or eliminate white film. Also, by using a rinse aid you can minimize

repeat buildup of white film.

Powders and Gels

• The amount of detergent to use depends on: How much soil remains on the items - Heavily soiled loads

require more detergent.

The hardness of the water - If you use too little in hard water,

dishes won't be clean. If you use too much in soft water, glassware will etch.

Soft to Medium Water (0-6 grains per U.S. gallon) [typical water softener water and some city water]

Medium to Hard Water (7-12 grains per U.S. gallon) [well water and some city water]

• Depending on your water hardness, fill the Main Wash section of the dispenser as shown. Fill the Pre-Wash section to the

level shown, if needed.

NOTE: Fill amounts shown are for standard powdered detergent. Follow

instructions on the package when using other dishwasher

Soft Water

X ard Water

MainWash

HardWater

SoftWater

Pra-Wash

detergent types.

Add Rinse Aid

• Your dishwasher is designed to use rinse aid for good drying

performance. Without rinse aid your dishes and dishwasher interior will have excessive moisture. The heat dry option will not perform as well without rinse aid.

• Rinse aid keeps water from forming droplets that can

dry as spots or streaks. They also improve drying by allowing water to drain off of the dishes after the final

rinse.

• Rinse aid helps to reduce excess moisture on the dish

racks and interior of your dishwasher.

Full Add

STEP3

Select a Cycle (cycles vary by model)

See "Cycle and Option Descriptions" charts in the following section.

Efficient dishwashers run longer to save water and energy, just as driving a car slower saves on gas. Typical cycle time is

approximately 21/2hours, but can take less or more time to complete depending on selections.

CYCLES

Select Options (options vary by model)

See "Cycle and Option Descriptions" charts in the following section.

You can customize your cycles by pressing the options desired. If you change your mind, press the option again to turn off the option.

Not all options are available for every cycle. If an invalid option is selected for a given cycle, the lights will flash.

OPTIONS

Sound On/O{{ " _ See Hold 3 Sec

STEP4

Start or Resume a Cycle

NOTE: Run hot water at the sink nearest your dishwasher until the water is hot. Turn off water.

Push door firmly closed within 3 seconds of pressing START/RESUME. If door is not closed within 3 seconds, the Start indicator will flash, an audible tone will be heard, and cycle will not

start.

IMPORTANT: If anyone opens the door (such as, for adding a dish, even during the Delay Hours option), the Start/Resume button

must be pressed each time.

• Press START/RESUME to repeat the same cycle and options as in the previous wash cycle.

Repeat Last Cycle

i J

This information covers several different models. Your dishwasher may not have all of the cycles and options described.

CYCLES SOIL LEVEL WASH TIME* (MINS.) WATER

W/O OPTIONS USAGE

GALLONS

TYPICAL** MAX (LITERS)

The most advanced and versatile cycle. Sensor Wash Light to Medium !!0 !50 3.8(!4.5)

| I Sensor I cycle senses the load size, soi! amount, and

| I Wash I toughness of soil, to adjust the cycle for optimal ' ....Tough/Baked .... 125 ........, 190 ........, 5,0(19.1)

cleaning using only the amount of water and energy On

needed.

I Heavy

Wash

i i I I

Use for hard-to-clean, heavily soiled pots, pans,

casseroles, and tableware.

• Heavy _ _ !90. 7:7 (29.0)

Heavy/Baked-

140 205 7.9 (30.0)

This cycle is recommended to Completely wash a full Light , !!0 I !50' 2.8 (!0.5) ....

| Normal

Wash

load of normally soiled dishes. Selecting this cycle will default to the options recommended for normal ' Medium . 110 , 150 4.0 (!5.0)

I I

amounts of food soil. The energy label is based on this , i i cycle. Heavy ' 125 190 7:7 (29.0)

Use for lightly soiled items or china and crystal. Light to Medium 105 145 4.2 (15.2)

I China!

Crystal Heavy/Baked- 120 185 7.7 (29.0)

' When you need fast resu!ts, the1 Hour Wash Will clean AIi Soil levels 58 63 6 2(23:5)

ml Houri dishesusing slightlymore water and energy:Selectthe I I

mI Wash I Precision Dry®or Precision Dry®+option to speed I I I I

drying times (adds approximate!y 27 t0 35 minutes to I I I I

the1 Hour Wash cycle). I I I I

Use for rinsing dishes, glasses, and silverware that will All soil levels 17 20 2.4 (9.0)

I Rinse not be washed right away.

On y Do not use detergent.

Wash times depend on water temperature, heavy soil condition, dish load size and options selected. Adding options will add time to the cycle.

*Adding options will add time to the cycle. See options information section.

**This is the approximate cycle time obtained with 120°F (49°C) hot water available at the dishwasher. Increase in time results from low

temperature of the incoming water.

OPTIONS CAN BE WHAT IT DOES ADDED TIME TO CYCLE ADDED

SELECTED WITH WATER

GALLONS

TYPICAL MAX (LITERS)

I Raises the main wash I Heavy Wash I Raises the main I 22 I 40 I O- 3.0

| _ temperature to improve I Normal Wash I wash temperature I I I In - t t _

• _1_2_£_1 cleaning for loads ' Sensor Wash from 105°F (41°C) I I I '- .... ' ;

.... do./off-_oc containing tough, baked- to 140°F (60°C). I I I

on food. I I I I I

Raises the temperature Heavy Wash Raises main wash 78 100 O- 3.9

I Steam with the power of steam Sensor Wash temperature from (O- 14.9)

Finish before final rinse to help Normal Wash 105°F (41°C) to

enhance shine, finish and 140°F (60°C), reduce glass spots, steam clean before

rinsing, final rinse temperature 140°F

(60°C) to 155°F (68°C).

Sanitizes dishes and Heavy Wash Increased the main 53 73 0 - 3.0

[] I g assware in accordance Normal Wash wash temperature 10 11 2_

| Sanitize with National Sanitation SensorWash from 105°F(41°C) _ - • i

' Foundation (NSF)/ANSI to 140°F (60°C) and

I Standard 184for I I the !inal rinsefrom I I I

Residential Dishwashers. 140 F (60 C) to Certified residential 155°F (68°C). dishwashers are not

ntended for censed food I

establishments. The Sani I I I

successfully completed. If ' I I I I

to the cycle being ' I I I I

interrupted. I I I I I

For added convenience, Available with Slightly faster wash -7 -30 O

I Rack load of dishes in the top

Top use for washing a small any cycle for smaller loads

rack to help keep the

kitchen continuously clean•

Dries dishes with heat and Available with Uses the heating 44 51 0 ;;

| I Precision a fan. This option with the any cycle except element to heat air,

| I Dry + I use of rinse aid will provide I Rinse Only I plus a system of I I I

the best drying I I vents and a fan that performance. Plastic items ventilates moist air are less likely to deform out of the I I I

when loaded in the top dishwasher to '.

rack. Turn Prec,s,on Dry + I I speed dry,ngt,mes. I I I

• . ® • .

opt on off for an air dry. Precision Dry®+

option defaults to

I I I.ON when any cycle I I I

I , Jsselected except I I I

: .. for 1 Hour Wash. I I I

Dries dishes with heat. This option with the use of rinse aid will provide the

best drying performance.

Plastic items are less likely to deform when loaded in

the top rack. Turn

Precision Dry_off for an air dry.

Available with

any cycle except

Rinse Only

Activates the heating element at

the end of the wash cycle to speed drying times.

Precision Dry®

defaults to ON when any cycle is selected except for

1 Hour Wash.

52 52 O

OPTIONS

CAN BE SELECTED WITH

WHAT IT DOES

ADDED TIME TO CYCLE

TYPICAL MAX

ADDED WATER

GALLONS

(LITER_

! 4 Hour

De ay

Control Lock

l ControlI

I Lock I

Hold 3 Sec

Control lock - 3 Sec

Runs the dishwasher at a later time or during off-

Available with

any cycle

Delays the start of a

cycle up to 4 hours.

240 240

peak electrical hours. Select a wash cycle and

options. Press 4 HOUR

DELAY. Press START/

RESUME. Close the door firmly.

NOTE= Anytime the door is opened (such as, to add a

dish), the Start/Resume button must be pressed

again to resume the delay countdown.

Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle. Toturn on Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The Control

Lock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button while your dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the

controls are locked. To turn off Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The light

turns off.

NOTE: If your model requires you to press and hold 4 Hour Delay to lock the controls, the Control Locked LED will be on or off to indicate if the Control Lock is active or not.

CONTROL PURPOSE COMMENTS

Tostart or iesume a !f the do0r is opened during acYcle oi powei is interrupted, the start/Resume indicator wash cyc!e flashes: Press START/RESUME and pUShthe d0or firm!y €!osed wi!hin 3 seconds.

L ...... _ NOTE" If the door is not closed within 3 seconds, the StartJResume indicator will flash; an

Repeat Last Cycle

To reset any cycle or

I Cancel/ I options during

audible tone wil! be heard, and the cYCle will not start,

Press CANCEL/DRAIN to reset any control selections made.

| _ selection.

To cancel a wash cycle after it's

See "Canceling A Cycle" and "Changing a Cycle After Dishwasher Is Started" sections.

started.

To turn the audible Press and hold the super scrub button for3 Seconds tO turn the audible tones on or off.

| _ tones on croft. On!y audible tones for confirming button presses can be turned on/off, Important audible

Sound On/Off - 3 Sec

tones, such as indicating a cycle has been interrupted, cannot be deactivated.

/_ _!i:_JW_!!_!i__!_j I::_!!_iiiiiii_!!i_ii_i__!!ii_!!_i_ili_ii_ii

CONTROL PURPOSE COMMENTS

The Cycle Status Indicator Clean indicator glows when a cycle is finished. Lights are used to follow the If you select the Sanitize option, when the Sanitize cycle is finished, the

progress of tne aJsnwasner Sanitized indicator glows. If your dishwasher did not properly sanitize your cycle. Located on the front dishes, the light flashes at the end of the cycle. This can happen if the

of the dishwasher for front cycle is interrL pted, or the water could not be heated to the required control models, and located temperature.

on the top of the door for hidden control models. The Clean and Sanitized lights go off when you open and close the door or

press CANCEL.

Canceling A Cycle

1. Open the door slightly to stop the cycle. Wait for the spraying action to stop before completely opening the door.

2. Press the Cancel/Drain button once. The Cancel/Drain light will light up.

3. Close the door and the dishwasher starts a drain cycle (if water

remains in bottom of dishwasher). Let the dishwasher drain completely. The Cancel/Drain light turns off after 2 minutes.

Changing A Cycle After Dishwasher Is Started

1. You can interrupt a cycle and restart your dishwasher from the beginning using the following procedure.

2. Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely.

3. Check that detergent dispenser cover is still closed. If cover is open, you will need to refill the detergent dispenser before restarting your new cycle.

The Front Indicator Light or Single Exterior Light (A)

shows progress of your dishwasher cycle by color

(for non-Pro handle hidden control models only).

The light will be blue if the dishwasher is washing or rinsing. The light will

be red when the dishwasher is drying. The light will be green to indicate

that the cycle is complete. If the Front Indicator Light is blinking, see

"Troubleshooting" section.

4. Press CANCEL/DRAIN twice to reset the control.

5. Select new cycles and options.

6. Press START/RESUME.

Adding A Dish After Dishwasher Is Started

1. Check if Add a Dish indicator is lit. (Available on some models. Otherwise, proceed to Step 2.)

2. Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely.

3. Check whether the detergent dispenser cover is still closed. If it is open, the wash cycle has already started and adding a

dish is not recommended.

4. If detergent has not yet been used (detergent dispenser cover is closed), you may add a dish.

5. Press START/RESUME.

Your Jenn-Air _ dishwasher may have some or all of these features.

Silverware Basket

Use the slots in the

covers to keep your silverware separated for

optimum wash. There are specially designed

slots (small round holes) for chopsticks. Mix silverware types to keep them separated. Load

knives down, forks up, and alternate spoons, for best cleaning

results.

NOTE: If your silverware does not fit into the designated slots, flip

the covers up and push them down into the basket.

Cup and Stemware Holder (on some models)

Fold down the extra shelf on the left-hand or right-hand side of the mid level rack to hold additional cups, stemware or long items such

as utensils and spatulas.

NOTE: Remove the culinary tool basket(s) when washing tall stemware or other tall items in the top rack.

Flexible Tines

The row of tines on the left-hand and right-hand sides of the top rack can

be adjusted to make room for a

variety of dishes. To adjust the fold-down tines:

1. Grasp the tip of the tine that is in the tine holder.

2. Gently push the tine out of the holder.

3. Lay the tines down, toward the center of the rack.

NOTE: The bottom rack may also have 1 or 2 rows of flexible tines located in the back of the rack. Follow the same instructions to

adjust.

Light Item Clips

The light item clips hold lightweight plastic items such as cups, lids, or bowls in place during

washing. To move a clip:

1. Pull the clip up and off the tine.

2. Reposition the clip on another tine.

Premium Adjustable 2-Position Top Rack

After removing the culinary tool rack, you can raise or lower the

top rack to fit tall items

in either the top or bottom rack.

Adjusters are located on each side of the

top rack. Each adjuster has 2 preset

positions.

To raise the rack,

press both rack adjusters and lift the rack until it is in the Up position and level.

To lower the rack, press both rack adjusters and slide the rack to its

Down position and level.

Manual Adjustable 2-Position Top Rack

You can raise or

lower the top I_ items in either the

top or bottom rack. Adjusters

are located on each side of the

rack to fit tall _ top rack. Raise

the top rack to accommodate

items up to 9"

(22 cm)in the top rack and 13" (33 cm)in the bottom rack, or lower the top rack to accommodate items up to 11" (28 cm) in both the

top and bottom racks.

IMPORTANT: Remove dishes prior to removing the top rack from

the dishwasher. To raise, remove rack and slide lower wheels into the rails as

directed in "Removable Top Rack" section. To lower, remove rack and slide upper wheels into the rails as

directed in "Removable Top Rack" section.

Removable Top Rack (for Roller Glide Rails) The removable top rack allows you to wash larger items such as

pots, roasters, and cookie sheets in the bottom rack. IMPORTANT: Remove dishes prior to removing the top rack from

dishwasher. To remove the rack

To gain access to the track stops, pull the upper rack forward about halfway out of the tub.

To open, flip the track stop toward the outside of the tub. After opening both track stops, pull top rack out of the rails.

Track stop closed Track stop open

Removable Top Rack (for Ultra Glide rails) The removable top rack

allows you to wash larger items such as pots, roasters,

and cookie sheets in the bottom rack.

IMPORTANT: Remove dishes prior to removing the

top rack from the dishwasher.

To remove the rack:

To gain access to the removable tabs on the

tracks/rails, pull the upper rack forward about halfway out of the tub.

On one side, press the tab on the track in and pull up the front end of the rack out of the track. Then repeat this step on the other side

to completely remove the front end of the rack. Then remove the back end of the rack, by pulling the back end out

with a slightly forward then upward motion.

To replace the rack:

Pull the tracks forward about halfway out of the tub. Along the sides of the racks are round attachment tabs. Align the

rack's back end attachment tabs with the cutout in the track. Push down into place.

Pull the tracks completely out, and align the rack's front end attachment tabs with the cutout in the track. Push down into place.

You will hear a snap when the front end of the rack is secured into place on each side.

Removable Culinary Tool Rack (3rd level rack)

The removable Culinary Tool

Rack (3rd level rack) allows

you to wash larger items in the upper rack, or remove

both the Culinary Tool Rack

and top rack to wash larger B times in the lower rack. See

"Removable Top Rack"

section. To remove the Culinary

Tool Rack:

1. To access track stops, pull the rack forward until it stops and clicks into place.

2. To open track stops, flip the track stop to the outside of the track.

3. After opening both track stops, slide front wheels up and out

of the slot in track. Continue to pull rack forward in track and

slide the back wheels up and out of the track.

4. Close track stops.

5. Slide rack tracks back into dishwasher.

To replace the rack:

1. Gently pull rack tracks forward in dishwasher until they stop and click into place.

2. To open track stops, flip the track stop to the outside of the track.

3. Place the back rack rollers on each side of the rack into the track slot and roll the rack back into the tracks.

4. Insert front rack rollers on each side of the rack into the rack slots.

5. Close track stops on both sides of rack and slide rack back

into dishwasher.

Culinary Tool Rack (3rd level rack) The culinary tool rack is designed with 2 movable baskets to hold

extra silverware, knives and cooking utensils. Install the baskets in this up position when you have extra

silverware and flatware to wash.

Up position

Install the baskets in this down position when you have extra silverware, knives, or utensils requiring more room to wash.

IMPORTANT: When you are using the culinary tool baskets in the down position, the top rack must also be in the lowest position.

Downposition

Remove the front basket in the down position, when you are using the cup shelves or other tall items in the top rack for more room.

......

Your dishwasher has the latest technology in dishwasher filtration. This triple filtration system minimizes sound and optimizes water and energy conservation while providing superior cleaning performance. Throughout the life of your dishwasher, the filter will require

maintenance to sustain peak cleaning performance.

The triple filter system consists of 2 parts, an upper

filter assembly and a lower filter.

• The upper filter assembly keeps oversized items and foreign objects, along with very fine food

Upper Filter

particles, out of the pump.

• The lower filter keeps food from being recirculated onto your dishware.

Assembly .....___

The filters may need to be cleaned when:

• Visible objects or soils are on the Upper Filter

Assembly.

• There is degradation in cleaning performance (that is, soils still present on dishes).

• Dishes feel gritty to the touch.

It is very easy to remove and maintain the filters. The chart below shows the recommended cleaning

frequency.

Lower Filter

Number of Loads

Per Week

8-12

1-3

If you only scrape before loading*

Every two months Every four months Twice per year

If you scrape and rinse before loading

Every four months Once per year Once per year

If you wash before loading

Once per year

*Manufacturer's recommendation: This practice will conserve the water and energy that you would have used to prepare your dishes. This

will also save you time and effort.

Very Hard Water

Ifyou have hard water (above 15 grains), clean your filter at least

once per month. Building up of white residue on your dishwasher

indicates hard water. For tips on removing spots and stains, see "Troubleshooting" section.

Filter Removal Instructions

Cleaning Instructions

IMPORTANT: Do not use wire brush, scouring pad, etc., as they may damage the filters.

Rinse filter under running water until most soils are removed. If you have hard-to-remove soils or calcium deposits from hard water, a

soft brush may be required.

1. Turn the Upper Filter Assembly 1¼turn

counterclockwise and lift

tab

out.

2. Grasp the Lower Filter in the circular opening, lift

slightly, and pull forward to remove.

3. Clean the filters as shown

below.

To remove Upper Filter Assembly

Filter Reinstallation Instructions

Noting the previous illustrations, place the

Lower Filter under the Locating Tabs in the

bottom of the dishwasher so the round opening for

the Upper Filter Assembly lines up with the round opening in the bottom of

the tub.

Cleaning

Cleaning the exterior

tab

To replace Upper Filter Assembly

Clean the exterior of dishwasher with a soft, damp cloth and mild detergent. If your dishwasher has a stainless steel exterior, a stainless steel cleaner is recommended -

Stainless Steel Cleaner and Polish Part Number 31462A.

Insert the Upper Filter Assembly into the circular opening in the Lower Filter.

Slowly rotate the filter clockwise until it drops into place. Continue to rotate until the filter is locked into place. If the filter is not fully seated (still turns freely), continue to turn the filter clockwise until it drops and locks into place.

NOTE: The Upper Filter Assembly arrow does not have to align with the arrow in the Lower Filter as long as the filter is

locked.

IMPORTANT: To avoid damage to dishwasher, do not operate your dishwasher without the filters properly installed. Be sure the Lower

Filter is securely in place and the Upper Filter Assembly is locked into place. If the Upper Filter Assembly turns freely, it is not locked

into place.

Cleaning the interior Removal of Hard Water/Filming

For removal of hard water/filming, it is recommended use of a monthly maintenance product such as affresh ®Dishwasher Cleaner Part Number W10282479.

• Load your dishwasher (preferably with dishes affected by filming / hard water).

• Place tablet in main wash compartment of detergent dispenser.

• Select cycle/option best for heavily soiled dishes and start dishwasher.

Hard water minerals can cause a white film to build up on the inside surfaces, especially just beneath the door area.

NOTE: Recommended to use a premeasured detergent tablet or pack for regular daily

use.

Do not clean the dishwasher interior until it has cooled. You may want to wear rubber gloves. Do not use any type of cleanser other than dishwasher detergent because it may

cause foaming or sudsing. To clean interior:

Make a paste with powdered dishwasher detergent on a damp sponge and clean. OR Use liquid automatic dishwasher detergent and clean with a damp sponge. OR

See the vinegar rinse procedure in "Cloudy or Spotted Dishware" in the "Troubleshooting" section.

NOTE: Run a normal cycle with dishwasher detergent after cleaning the interior.

Drain Air Gap

Some state or local plumbing codes require the addition of a drain air gap between a built-in dishwasher and the home drain system. Check the drain air gap when your

dishwasher is not draining well.

The drain air gap is usually located on top of the sink or countertop near the dishwasher.

NOTE: The drain air gap is an external plumbing device that is not part of your dishwasher. The warranty provided with your dishwasher does not cover service costs directly associated with the cleaning or repair of the external drain air gap.

To clean the drain air gap

Clean the drain air gap periodically to ensure proper drainage of your dishwasher. With most types, you lift off the chrome cover. Unscrew the plastic cap. Then check for any soil

buildup. Clean if necessary.

Vacation or Extended Time Without Use

To reduce the risk of property damage

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

Inthe U.S.A., www.jennair.com In Canada, www.jennair.ca PROBLEM RECOMMENDED SOLUTION DISHWASHER DOES NOT RUN

OR STOPS DURING A CYCLE

DETERGENT REMAINS IN THE DISPENSER OR

TABLET IS ON BOI-I'OM OFTUB

CYCLE RUNS TOO LONG

NOTE: It is normal for the dishwasher to repeatedly pause several times during a cycle. If the Start/Resume light is blinking, close the door and push START/RESUME.

Be sure the door is closed and latched. Check that there is not an interference with large casserole dishes and the wash system at the back of

the dishwasher. Adjust loading as necessary to ensure door is closed and latched. Be sure you have selected a cycle. (See "Cycle and Option Descriptions" section.)

Be sure there is power to the dishwasher. A circuit breaker or fuse may have tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

Has the motor stopped due to an overload? The motor automatically resets itself within a few minutes. If it does not restart, call for service.

If lights other than Start/Resume blink and the unit will not run, you will need to call for service. Check that the water shutoff valve, if installed, is turned on.

Check for dishware such as cookie sheets, cutting boards, or large containers, etc., that may be blocking the detergent dispenser from opening properly.

Be sure your detergent is fresh and lump free. Be sure the cycle has completed (the Clean light is on). If it has not completed, you will need to

resume the cycle by closing the door and pressing START/RESUME. NOTES:

• To use less water and reduce energy consumption you will encounter cycles that typically run for

• A water heater setting of 120°F (49°C) is best, the dishwasher will delay longer while heating

• Some options will add time to the cycle. (See "Cycle and Option Descriptions" section.) The

Try the 1 Hour Wash cycle. Run the hot water at a faucet close to the dishwasher before starting the cycle.

• If you will not be using the dishwasher during the summer months, turn off the water and power supply to the dishwasher.

• Make sure the water supply lines are protected against freezing conditions. Ice

formations in the supply lines can increase water pressure and damage your

dishwasher or home. Damage from freezing is not covered by the warranty.

• When storing your dishwasher in the winter, avoid water damage by having your dishwasher winterized by authorized service personnel.

to possibly avoid the cost of a service call.

up to 3 hours.

cooler water.

Precision Dry®or Precision Dry®+ option adds approximately 1/2hour.

PROBLEM RECOMMENDED SOLUTION

DISHWASHER NOT DRYING

WILL NOT FILL

WATER REMAINS IN THE TUB/ WILL NOT DRAIN

HARD WATER

(WHITE RESIDUE ON

DISHWASHER INTERIOR OR

G LASSWA RE)

ODORS

NOISY

FOOD SOILS REMAIN

ON DISHES

NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a porous

surface which tends to collect water droplets. Towel drying may be necessary. Use of rinse aid along with the Precision Dry®or Precision Dry®+ option is needed for proper drying.

Proper loading of items can affect drying. (See specific loading instructions within this guide.) Glasses and cups with concave bottoms hold water. This water may spill onto other items when

unloading.

• Unload the bottom rack first.

• Locate these items on the more slanted side of the rack for improved results. Be sure the water is turned on to the dishwasher. Check that the float is free from obstructions. (See "Parts and Features" to identify the location of the

float.) Check for suds in the dishwasher. If foam or suds are detected, the dishwasher may not operate

properly or may not fill with water. (See "BLINKING LIGHTS" in "Troubleshooting.") Be sure the cycle has completed (the Clean light is on). If it has not, you will need to resume the cycle

by closing the door and pressing START/RESUME. If dishwasher is connected to a food waste disposer, be sure the knockout plug has been removed

from the disposer inlet. Check for kinks in the drain hose.

Check for food obstructions in the drain or disposer. Check your house fuse or circuit breaker.

NOTE: Extremely hard water mineral deposits can cause damage to your dishwasher and make it difficult to achieve good cleaning. A water softener is strongly recommended if your hardness is

15 grains or more. If a water softener is not installed, the following steps may help: Use affresh ®dishwasher cleaner to remove buildup from dishwasher and dishware once per month.

Clean the upper and lower filters at least once per month. (See Cleaning Instructions in "Filtration System" section.)

Always use a rinse aid. Always use a high-quality, fresh detergent.

Use a detergent booster/water softener additive designed for dishwashers. NOTE: If the dishwasher is not used daily, you can run a rinse cycle with the partial load until a full

load is ready to run, or use the Top Rack Only option (on some models) for partial loads. Run a vinegar rinse through the dishwasher by putting 2 cups (500 mL) of white vinegar in an upright

glass measuring cup in the lower rack. Run a normal cycle with the Heat Dry option turned off. Do not use detergent.

The dishwasher may not be draining properly, see "WATER REMAINS IN THE TUB/WILL NOT DRAIN" in "Troubleshooting."

NOTES:

• Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.

• Normal water valve hissing may be heard periodically.

• A normal snap sound may be heard when the detergent dispenser opens during the cycle and when the door is opened at the end of the cycle.

• Improper installation will affect noise levels.

Be sure the filters are properly installed. A thumping sound may be heard if items extend beyond the racks and interfere with the wash arms.

Readjust the dishware and resume the cycle. Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing

performance (see "Dishwasher Use"). Check filter to ensure it is properly installed. Clean it if needed. (See Cleaning Instructions in "Filtration

System" section for details.) Select the proper cycle for the type of soils. The Sensor Wash or the Heavy Wash cycles can be used

for tougher loads. Be sure the incoming water temperature is at least 120°F (49°C).

Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and hard water conditions.

Scrape food from dishes prior to loading (do not prerinse).

PROBLEM RECOMMENDED SOLUTION

DISHES DIRTY/SUDS IN DISHWASHER/CYCLE NOT

COMPLETE

DID NOT SANITIZE If the sanitized light is blinking, the load is NOT sanitized. The cycle was interrupted in the final rinse,

DAMAGE TO DISHWARE Improper loading can cause dishes to become chipped or damaged. (See specific loading

BLINKING LIGHTS Blinking LED's will occur when the cycle is paused or when the cycle has been interrupted by

CLOUDY OR SPOTTED

DISHWARE (AND HARD

WATER SOLUTION)

ETCHING (PERMANENT

CLOUDINESS)

LEAKING WATER

TUB IS DISCOLORED

If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate properly or may not fill with water.

Suds can come from:

• Using the incorrect type of detergent, such as dish detergent for hand washing dishes, laundry detergent, or hand soap.

• Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid.

• Using an excessive amount of dishwasher detergent.

Call for service. If no water was present in the machine at any time during a heated wash cycle, the cycle will end and

the Clean LED will not come on. See "Will Not Fill" in "Troubleshooting."

or the temperature for your water heater is set too low. Set your water heater to 120°F (49°C).

instructions within this guide.)

opening the door. In this case, the Start/Resume button LED, the Cycle Status Indicator LED(s), and the countdown bars on the Cycle Status Display all blink together to indicate that attention is needed. See Start or Resume a Cycle in the "Dishwasher Use" section.

Blinking LED's can also occur when certain errors have been detected. In this case, the Clean/ Complete LED will blink 4 times in a row with a pause in between each set of blinks. When this error

occurs, the controls will lock out and not allow another cycle to be started. Call for service.

NOTES:

• Liquid rinse aid is necessary for drying and to reduce spotting.

• Use the correct amount of detergent.

Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. If the cloudiness disappears, it is due to hard water. Adjust the amount of detergent and rinse aid. (See

"HARD WATER [WHITE RESIDUE ON DISHWASHER INTERIOR OR GLASSWARE] in "Troubleshooting.") If it does not come clear, it is due to etching (see below).

Be sure the incoming water temperature is set at 120°F (49°C). Try using the Super Scrub and Sanitize options.

To remove spotting, see the "Dishwasher Care" section. This is an erosion of the surface of the glassware and can be caused by a combination of: water that

is too hot, from using too much detergent with soft water or by pre-washing. Detergent needs food soil to act upon. If etching has occurred, the glassware is permanently damaged. To avoid further

etching, adjust the detergent amount to match the water hardness, stop pre-washing, and use water heating options only when incoming water temperature is below 120°F (49°C).

Be sure dishwasher has been installed properly and is level. Suds can cause the dishwasher to overflow. Measure the detergent accurately and use only

detergents designed for use in a dishwasher. Less detergent is needed in soft water. Try another brand of detergent if sudsing continues.

To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached and avoid overfilling.

NOTES:

• High iron content in the water can discolor the tub.

• Tomato-based foods can discolor the tub or dishware.

A citrus-based cleaner can be used to clean.

The Clean light is flashing Check the following:

• Is the overfill protection float able to move up and down freely? Press down to release.

• Be sure the water supply is turned on to the dishwasher. (This is very important following the new installation of your dishwasher.)

• Check for suds in the dishwasher. If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate properly or may not fill with water.

Suds can come from:

• Using the incorrect type of detergent, such as laundry detergent, hand soap, or dish detergent

for hand washing dishes.

• Forgetting to replace the rinse aid dispenser cap after filling (or refilling) the rinse aid.

• Using an excessive amount of dishwasher detergent.

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated and maintained according to instructions attached to or furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will pay for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this appliance was purchased.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CERTAIN COMPONENT PARTS

In the second through the fifth year from the date of original purchase, when your major appliance is installed, operated and maintained according to instructions attached to or furnished with the product, Jenn-Air will pay for factory specified replacement parts for the following components to correct non-cosmetic defects in materials or workmanship that existed when this major appliance was

purchased: dish racks, all parts of the wash system, drain motor, electronic controls and heating element. Replacements parts will also be

provided if there is rust including the exterior cabinet and front panels.

LIFETIME LIMITED WARRANTY ON STAINLESS STEEL TUB AND INNER DOOR LINER

For the lifetime of the product from the date of purchase, when this major appliance is installed, operated and maintained according to

instructions attached to or furnished with the product, Jenn-Air will pay for factory specified parts and repair labor for the following components to correct defects in materials or workmanship that existed when this major appliance was purchased: stainless steel tub

and inner door liner.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THE LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. Service must be provided by a Jenn-Air designated service company. This limited warranty is valid only in the United States and Canada

and applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under the limited warranty.

ITEMS JENN-AIR WILL NOT PAY FOR

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty coverage.

3. Replacement parts or repair labor when your major appliance is used for other than normal, single-family household use or when it is used in a manner inconsistent to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance

with electrical or plumbing codes, or use of products not approved by Jenn-Air.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada.

6. Pickup and delivery. This major appliance is designed to be repaired in the home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service in remote locations where service by an authorized JennAir servicer is not available.

9. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions.

10. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was purchased.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask Jenn-Air or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

and applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this limited warranty.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Jenn-Air dealer to determine if another warranty applies. 11/11

For additional product information, in the U.S.A., visit www.jennair.com. In Canada, visit www.jennair.ca

If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may contact Jenn-Air at the number below.

Have your complete model number ready. You can find your model number and serial number on the label located near the door on the right-hand or left-hand side of the dishwasher interior.

For assistance or service in the U.S.A., call 1-800-688-1100. In Canada, call 1-800-807-6777.

If you need further assistance, you can write to Jenn-Air with any questions or concerns at the address below:

In the U.S.A.: In Canada:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Jenn-Air Brand Home Appliances Customer eXperience Center

200--6750 Century Avenue Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Please keep these User Instructions and model number information for future reference.

W10596272A

Printed in U.S.A.

5/13

+ 45 hidden pages