Jenn-Air JDB4000AWW, JDB4000AWQ, JDB4000AWB, JDB2150AWP, JDB1270AWY Owner’s Manual

...
JENN-AIR DISHWASHER
JDB-5
TABLE OF CONTENTS
E
6 918350 A @2003 Maytag Appmiances Sames Co.
What You Need to Know About
Safety instructions
Warning and Important Safety' Instructions appearing in this
manual are not meant to cover aH possiMe conditions and
situations that may occur. Common sense, caution and care
must be exercised when installing, maintaining or operating
the dishwasher. Always contact your dealer, distributor, service agent or
manufacturer about problems or conditions you do not understand.
Recognize Safety Symbols, Words, Labels
important Safety instructions
Products with a u£_)Habdhave been Histedwith Underwriter's Laboratories, Inc. - those with a CSA tag have
been Histedwith Canadian Standards Association. NevertheHess,as with any other equipment using dectricity
and moving parts, there is a potential hazard.
1+Read all instructions before using the dishwasher+
2. Use the dishwasher only for its intended function.
3. Disconnect electrical power to dishwasher before attempting to service.
4. To avoid electrical shock hazard, the sides and back must be enclosed and the front panels must be attached
before electrical power is applied to the dishwasher. Refer to the installation instructions for proper
grounding procedures.
5. Connect to a properly rated, protected and sized power
supply circuit to avoid electrical overload.
6. Children should never be permitted to operate, or play in, with, or around this dishwasher+
7:To reduce the risk of injury when loading items to be
washed, sharp or pointed items should be located with the handles up. Also, load sharp items so they are not
likely to damage the door seal.
8. Do not touch the heating element on the bottom of the
tub during or at the completion of a cycle. It will be hot.
9. Useonly detergents and rinse additives designed for a residential automatic dishwasher+Never use soap, laundry
detergent, or hand washing detergent in your dishwasher.
Keep these products out of reach of children.
1O.Do not sit, stand on or abuse the door or dish racks of
the dishwasher.
11. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used
for two weeks or more. Hydrogen gas is explosive. If the hot water system has not been used for such a
period, turn on all hot water faucets and let the water
flow from each for several minutes. Thiswill release any accumulated hydrogen gas. As the gas is flammable+ do
not smoke or use an open flame during this process.
12. Do not wash plastic items unless marked "dishwasher
safe" or the equivalent. For plastic items not so marked, check the manufacturer's recommendations.
13. Do not tamper with controls.
14. To prevent accidental child entrapment and suffocation risks, always remove the door to the washing
compartment when removing an old dishwasher from service or discarding it.
15. Use caution when unloading the dishwasher. Dishes will be hot if unloaded shortly after a cycle has completed.
16. Certified residential dishwashers are not intended for licensed food establishments.
Save These instructions
for Future Reference
Before You Start
Operating the Dishwasher
. Don't prerinse° Simply scrape off any bones or
large food particles°
. If connected to a food waste disposer, make certain
the disposer is empty before starting the dishwasher.
. Scrape off tomato-based food soims (see page 15). . ftemove certain foods such as mustard,
mayonnaise, lemon juice, vinegar, salt or dressings
from stainless steel flatware as soon as
possibme. These foods may cause rusting and pitting if allowed to remain in contact with the surface for
an extended period of time.
Operating the Dishwasher
(MODELS WiTH FRONT OR COMBiNATiON FRONT AND TOP TOUCHPAD CONTROLS)
1. After loading the dishwasher and adding detergent, select the desired cycle and options by pressing the pads. The indicator lights for the selected cycle and options will ilhminate. To cancel an option press the pad again.
2. To start a cycle, close the door until it latches then press the STAftT/Cancem pad once. After a pause, the fill will begin. The display countdown (select models} will flash until STAftT!Oancem is pressed.
. If STAftT/Cancem is not pressed within 30
seconds of choosing your cycle, the dishwasher will turn off.
(MODELS WiTH TOP ONLY TOUCHPAD
After loading the dishwasher and adding
detergent, select the desired cycle and options by pressing the pads. The indicator lights for the
selected cycle and options will ilhminate. To cancel
an option press the pad again.
2_
To start a cycle, press the STAftT/Cancem pad
once. The indicator light will illuminate. Close the door until it latches. After a pause, the fill will begin.
If STAftT/Cancem is not pressed within 30
seconds of choosing your cycle, the dishwasher will turn off.
To prevent unplanned cycle or option changes, these selections are "locked in" after 1 minute.
The dishwasher remembers your last cycle so you
do not have to reset the cycle each time. To start the dishwasher using the same cycle and options selected on the previous wash, just press the STAftT!Cancem pad.
3_
To cancel a running cycle, carefully unlatch the
door without opening completely and wait for water circulation to stop. Press the START/
Cancel pad once and then shut the door. The
dishwasher will drain, then shut off. To turn the
dishwasher off without draining, press the STAftT!Oancel pad twice and then shut the door.
To prevent unplanned cycle or option changes, these selections are "locked in" after 1 minute.
The dishwasher remembers your last cycle so you do not have to reset the cycle each time. To start
the dishwasher using the same cycle and options selected on the previous wash, just press the STAftT!Cancel pad.
3. To cancel a running cycle, press the START/ Cancel pad once. The dishwasher will drain, then
shut off. To turn the dishwasher off without draining, press the STAftT/Cancel pad twice.
If a cycle pad is pressed after the controls have been "locked in", the light above the current cycle
will flash three times.
. If a cycle pad is pressed after the controls have
been "locked in", the light above the current cycle
will flash three times.
cont.
2
G
Operating the Dishwasher
[MODELS WiTH CYCLE SELECTOR KNOB)
1. After loading the dishwasher and adding detergent, select the desired cycle by turning the
cycle selector knob. Select options by pressing the buttons. The indicator lights for the options will illuminate. To cancel an option, press that button again.
2. To start a cycle, close the door until it latches then press the START button once. After a pause, the
fill will begin.
. If START is not pressed within 30 seconds of
choosing your cycle, the dishwasher will turn off.
To prevent unplanned cycle or option changes, these selections are "locked in" after one minute.
3. To cancel a running cycle, turn the cycle selector knob to Drain/OFF. The dishwasher will drain,
then shut off. To turn the dishwasher off without
draining, turn the cycle selector knob to Drain/ OFF then press the START button once.
Adding a Forgotten item
For best cleaning, the forgotten item should be added
early in the cycle.
1. Grasp door handle and unlatch door without opening completely. All lights will flash to indicate that the cycle is suspended.
2. Wait for the water circulation to stop.
3. Open the door and add the item.
4_
Close and latch the door. Lights will stop flashing when the door is properly shut. After a slight delay, the cycle resumes automatically at the point
of interruption.
If the door is opened during a running cycle,
there may be up to a 30 second delay before the dishwasher restarts after dosing the door.
Extended interruption of the wash cycle is not recommended.
General Recommendations
[Rack features vary by model)
. Items can be centered behind a single tine or loaded
at an angle to maximize space. Avoid blocking or preventing the spray arms from
spinning freely. Do not allow items to extend beyond the racks.
, Face soiled surfaces toward the center of the
dishwasher.
For best dishwashing results follow guidelines on following pages to determine the best arrangement for your items.
(SELECT MODELS)
10 Place Setting Load
Upper Rack (Models with folding and convertibJe bow_
tines in the lower rack)
The edge of the Stack°
Rack (select models} is
designed to hold stemware in place. Taller
stemware will fit better on the right side as the
upper rack is deeper on this side.
The J:olding Tines (select
models] located in the front right corner provide
convenient loading space for large, bulky items like
pots and pans or mixing
bowls. To lower tines, carefully push the tines out of each
holder toward the center of the rack and lay the tines
down. The Cup Clips (select
models} located in the
center of the upper rack
can be used to hold light- weight plastic items,
cooking utensils, knives,
etc. in place. Clip the item
between the tine and the clip.
% i[ : _ , !
,_ ;<.._'" :-_ _S_ __ j_
" I
Upper Rack
Glasses, cups, stemware, light-weight plastics, plates,
bowls, pans, long-handled utensils etc. can be loaded in this rack. Do not moad
glasses over the tines. The Stack-Rack (select
models] on the right side
of the upper rack folds
up or down for loading
flexibility. Fold it down to
hold long-handled knives, spatulas and spoons or
short items like cups or juice glasses. Fold it up for taller items like glasses, bowls, plates, etc.
The Vari-[ock" Snugger
(select models]) on the left secures lightweight items
in place. It can be
adjusted by grasping the wavy wire and rotating it
left to snug items against the outer rack or to the
right to rest on top of light items. Do not load items on top of the were.
For best results with tall
glasses, rest the bottom of the glass against the wavy
wire of the Vari-[oc_" Snugger (select models).
SELECT MODELS)
Lower Rack
A variety of items such as dinner plates, mixing bowls, pots and pans and baking
dishes can be loaded in this rack
Tail items such as bakeware and large platters can be
placed on the left side. With the Stack-
Rack (select models} shelf raised, thin items like cookie sheets
or pizza pans may be placed along the left side. With the shelf down, two levels of glasses and cups can be loaded.
Positioning the [:old- Away" Tines (select
models} flat in the back, left corner provides
convenient loading space for large, bulky items like
pots and pans or mixing bowis_
Convertible Tines (select models} in the back, right
corner can be adjusted to provide narrow spacing for loading plates or wide spacing for loading deep bowls, pots or
pans. Hip tines up for narrow spacing or down for wider spacing.
Back
Back
Utensil Baskets
Removable Standard Utensil
Basket (select models)
For best cleaning results, prevent
items from nesting together by
placing some items in the basket with handles up and some with
handles down. Load knives,
handles up and spoons and forks
handles down, through the slots in the hinged covered section(s} (when closed}.
Be sure that thin, finely pointed items do not extend through the baskeL This could block the lower wash
arm. Small, lightweight items like baby spoons and plastic
measuring spoons should be placed in the section(s} with the hinged cover(s}.
Split & Fit '' Uteusit Basket
(select models) The split silverware basket can
be separated and placed in several locations in the bottom
rack. Load flatware and utensils
into both sections or just one, depending on your load.
To spilt the
basket, hold the basket
firmly along the sides.
Unlock
baskets as shown here.
Auxiliary Basket
(select models)
Use this supplemental
basket in the upper rack for loading miscellaneous
items and utensils. This is also a safe place to bad
sharp knives and pointed items.
(SELECT MODELS)
10 Place Setting Load
Upper Rack
1 _;ailcer
is loaded
behind
dinner plates,
Middle Rack
like cups or juice glasses. Fold it up for taller items like
glasses, bowls, plates, etc. The edge of the Stack-
Rack (select models) is
designed to hold stemware
in place. Taller stemware will fit better on the right
side as the upper rack is
deeper on this side. The Folding Tines (select
models) located in the front
right corner provide
convenient loading space for
large, bulky items like pots
and pans or mixing bowls. To lower tines, carefully
push the tines out of each
holder toward the center of the rack and lay the tines
down.
Lower Fie×Load"" Rack
Upper Rack
Glasses, cups, stemware, light-weight plastics, plates, bowls, pans, long-
handled utensils etc. can be loaded in this rack Do
not load glasses over
the tines.
The Stack-Rack (select
models) on the right side of the upper rack folds up or down for loading
flexibility. Fold it down to
hold long-handled knives, spatulas and
spoons or short items
u u
The Cup Clips (select
models} located in the
center of the upper rack
can be used to hold light- weight plastic items,
cooking utensils, knives,
etc. in place. Clip the item
between the tine and the
clip_ The Vari-kock T''Snugger
(select models) on the left
secures lightweight items in
place. It can be adjusted by
grasping the wavy wire and
rotating it left to snug items
against the outer rack or to the right to rest on top of
light items. Do not load
items on top of the were.
For best results with tall
glasses, rest the bottom of the glass against the wavy
wire of the Vari-[.ock"
Snugger (select models).
3-- (SELECT mODELS)
Middle Rack
A variety of items such as cups, glasses, dinner
plates, mixing bowls, pots and pans and baking dishes can be
loaded in this rack.
Positioning the J:oJd_ Away" Tines (select models) fiat in front or
back of the silverware basket provides
convenient loading space for large, bulky
items like casserole dishes, water pitchers,
pots and pans or mixing bowls.
Lower Fie×Load ° Rack
A variety of large items such as casserole
dishes, baking pans, mixing bowls, and pots and pans can be
loaded in the lower rack. When deeper
dishes or pots and pans _ i_ _t i_ are located in this rack, u u u the middle rack can be
raised (see page 8). To accommodate exceptionally large, occasionally used items such as a canner on the lower FlexLoad" rack, the middle rack can be removed
(see page 8). For good wash action, place items so
soiled surfaces face down in the rack.
When covers are not in use, place flatware in basket some handles up and some down to avoid nesting. Small, lightweight items like
baby spoons and plastic
measuring spoons should
be placed in a section of the basket with cover
closed.
The split silverware basket can be separated in the
event both sections are not
needed to hold silverware.
To split the basket, hold the
basket firmly along the sides.
Unlock baskets as shown
here.
Auxiliary Basket (select models}
Use this supplemental
basket in the upper or
middle rack for loading
miscellaneous items and
utensils. This is also a safe place to load sharp
knives and pointed items.
Utility Basket for Lower Back (select models) This basket is
designed to load
miscellaneous items
like silverware, cooking utensils,
knives and other
larger utensils.
Utensil Baskets
Split & Fit TM Utensil Basket For best cleaning results, prevent items from nesting
together by placing a utensil in each sloL Load knives, handles up and spoons and forks handles down through the slots.
Be sure that thin, finely pointed items do not extend through the
basket bottom. This could block the wash arm.
7
Adjustabme Racks (select models:}
The Adjustable Upper Rack (select models) and
Adjustable Middle Rack can be raised or lowered to accommodate taller plates, platters, pans, etc. in the
upper, middle or lower racks. Full size dinner plates can be loaded in the upper rack if it is in the lower position. The rack is easier to adjust before it is fully
loaded.
To mower the rack: Adjusters
1. Pull the rack fully out.
2. Place thumbs on each lever
on the adjuster
while holding
rack with hands.
Removing the Upper
and Middle Racks
The racks can be removed when tall or oversized items
need to be loaded into the middle or lower rack. Unload the rack before removing it from the dishwasher.
To remove rack with push tab rack stops (select models):
1. Roll the rack '/._to '/_of the way out.
2.
To remove each plastic push tab rack stop from the end of each track, push inward (toward the rack) on the ridged area of the rack stop. The rack
stop will snap open and can be easily removed by pulling straight
out. Take care to support the track
while removing rack stops.
3. Press down on the levers with thumbs and push rack down. The rack will come to a stop when it is
in position.
To raise the rack:
1. Pull the rack fully out.
2. Place hands on both sides and lift up until rack comes to a stop and latches in place.
. The dishwasher will not
operate correctly if the rack wash arm
connection is not aligned
with one of the water
inlet holes on hack wall of the dishwasher.
. The left and right side adjusters on the racks
must both be fully in the upward or downward position for proper connection.
3. Roll the rack all the way out of
the track and remove from the
dishwasher.
Push Tab
Rack Stop
To replace: . Reverse the above procedure to replace the rack into
the dishwasher.
To remove rack with pull tab rack stops (select models):
1.
Roll the rack '/._to '/_of the way out.
2.
To remove each plastic pull tab rack stop from the end of each track, locate two-prong tab on inside of the rail and pull tab out toward rack. The rack stop can then be easily removed by pulling it
straight out. Take care to support the track while removing the rack stops.
.
Roll the rack all the way out of
the track and remove from the dishwasher.
To replace: . Reverse the above
procedure to replace the rack
into the dishwasher.
Pull Tab
Stop
Hot Water
For optimal cleaning and drying results, hot water is necessary° The incoming water temperature
shouJd he 120" F (49 ° C) to properJy activate the detergent and meJt greasy food soiJso
To check the incoming water temperature, turn on the
hot water faucet nearest the dishwasher and Jet it run into a glass in the sink. Place a candy thermometer in
the glass and check the temperature once it has stopped rising.
Add recommended amount of detergent to either side of the Main Wash compartment as shown and close
the detergent lid.
Use a detergent designed specifically for use in an
automatic dishwasher. Be sure it is fresh. Store granular detergent in a cool, dry place (not under the
sink).
Recommended Amount
Too little detergent results in poor cleaning, hard water filming/spotting and poor drying. Too much detergent
can cause permanent etching!cJoudines& The amount of detergent to use is determined by the
hardness of the water and soil level of the load. Refer
to the f@Jowing chart for detergent usage
recommendations.
Light Soil 5 teaspoons
Soft (0-4 gpg} Normal Soil 6 teaspoons
Heavy Soil 8 teaspoons
Light Soil 7 teaspoons
Medium (5-9 gpg} Normal Soil 8 teaspoons
Heavy Soil 10 teaspoons
Light Soil 9 teaspoons
Hard (10-12 gpg) Normal Soil 10 teaspoons
Heavy Soil 12 teaspoons
*Ybur local water utility or state university extension service can tell you the degree of water hardness in your area,
UnextremeJy hard water conditions (13 grains per gallon or more*), it is difficuJt to achieve good resuJts with any dishwasher. A mechanicaJ water softener may be necessary to improve water
quality, detergent effectiveness, and protect the dishwasher parts from the damage that hard
water can cause°
Do not use detergent with the Rinse OnJy cycle. Leave the detergent lid open when running Rinse Only.
Rinse Aid
Regular use of a rinse aid improves drying, reduces spotting and filming, and reduces
moisture melt on the dishwasher interior. An automatic rinse aid dispenser is located next to the
detergent cup.
The window next to the dispenser cap indicates when the rinse aid reservoir needs to be refilled. When the
level of rinse aid is below the indicator marks and the
window is nearly dear, it is time to refill the dispenser.
Check the dispenser monthJy.
To add rinse aid to the
dispenser: turn the cap counterclockwise to open.
Remove the cap and pour i liquid rinse aid into the
opening. The amount of rinse aid dispensed during
the cycle is adjustable by moving the lever inside the
reservoir area. For most water conditions use the manufacturer recommended setting of "2". Adjust it up to
the "MAX" setting for hard water. Set the lever anywhere
between these amounts as needed to get the best results. Replace the cap and turn it clockwise to close.
Choosethecyclethatbestdescribesyourdishloadbypressingthecorrespondingtouchpad.(Seepage2, OperatingTips,forhowto beginthe cycle[}.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiili¸_:_U_:__
Heavy Wash Long cycle for heavy food soils. 131 2 washes/3 rinses
Medium cycle for average food
Norma_ Wash soils. ClearScan" Turbidity 97-118 1-2 washes*/I-2 rinses*
sensor is active with this cycle.
China/Crysta_ Short cycle for light food soils. 82 2 washes/1 rinse
Designed to select the number
Sensor C_ean
(select mode_s[}
of water fills best suited for the soil level of each load. ClearScan '_
Turbidity sensor is active with this cycle.
97-131 1-2 washes*/1-3rinses _
Rinse Only there is a full load.
Quick Wash Quick cycle for light food soils. 38 1 wash/1 rinse
{:seJect _odeJs} Does not include drying time.
Numberof fills will va_7dependh_gon thesoil levelof each Goad.
Depending on water temperature, there may be time added to the cycle to bring water up to temperature.
Cycle times shown in the numerical display (select models:) will increase or decrease, based on each load's soil
level, water temperature and selected options.
Only the following certified cycles have been designed to meet NSF requirements (NSF/ANSI 184 Residential
Dishwashe0 for sanitization: Sensor Clean (select models:), Heavy Wash, Normal Wash and China!Crystal.
Rinses dishes being held until 9 1 rinse
IO
CycmeOptions
In addition to choosing a cycle from page 10, choose as many available options as are needed for your load.
Super Scrub
(select models[}
Sanitize
(select modelsD
Extra Rinse All cycles
(select models) (except Rinse Only_)
160 ° Rinse be used with any cycle except Quick Wash (select models_) Normal Wash
(semect modems) and Rinse Only. Sensor Clean* _._..t,,,o_J_._>
Heated Dry
Selected when washing loads with hard-to-remove food soils.
Depending on which cycle is being used, this option adds heat and/or wash time to the wash cycle.
Sanitizes dishware. When cycle monitor recognizes that the
proper conditions have been met, the SANITIZED light will activate at the end of the cycle. Sanitization may not be achieved if there is an interruption of the cycle, power failure
or if the incoming water temperature is below 120° F (49° C}.
Adds an additional rinse to cycle. An extra rinse helps to
improve results in hard water situations. Raises temperature in the final rinse to 160° R This option can Heavy Wash
For enhanced drying results select this option. When Heated Dry is not selected, towel drying of some items such as plastic and items with non-stick surfaces may be necessary and more moisture may be noticed adhering to the dishwasher interior. In models with plastic interiors, it is normal to notice vapor escaping from the door vent as the heat dries your dishes.
Vapor will escape even if Heated Dry is not selected.
Heavy Wash
Normal Wash China/Crystal
Sensor Clean (select models}
Heavy Wash*
Normal Wash*
Sensor CJean* {select models}
Heavy Wash
Normal Wash China/Crystal
Sensor Clean (select models}
* Only these cycles have been designated to meet NSF lequirements (NSF/ANSI 184 Residential DishwasheO fol sanitization.
Start!Oancem Starts and stops dishwasher. See page 2 under Operating "Nps: All Cycles
Starting the Dishwasher, for exp[anat[on_
Demay for instructions.
Controm Lock Option Locks control touchpad to prevent unwanted use. See page 13 All Cycles
(semect modems[} for instructions.
Used to automatically start the cycle at a later time. See page 12 All Cycles
11
TheDelayoptioncanbeusedto automaticallystart thecycleatalatertimeto reducedaytimeheat
buildupinthehomeortotakeadvantageof reduced energycostsifavailableinyourarea.Thisoptionis alsousefulfor conservinghotwaterattimesof high householdusage(showers,laundry).
Toset upa Delay:
1. Selecttheappropriatecycleandoptionsforthe load.Closethedoor.
2. PresstheDelaypadorbuttonuntilthedesired amountofdelaytimeisselected.
3. The Demay indicator and the count down display
(select models} will flash until the START!Cancel
pad or START button is pressed.
As soon as the START/Cancel pad or START
button is pressed, the flashing will stop and the delay time will begin counting down. The Delay indicator will remain lit until the delay time has
counted down.
5. The cycle will automatically start as soon as the delay time expires.
To cancel a Delay: When the delay is counting down, press the Delay
pad or button again. The indicator light will go out and
the cycle will start or resume immediately. To cancel a Delay and the cycle:
[All touchpad control models} . Press START!Cancel once to drain and turn off the
dishwasher.
Or
Press START/Cancel twice to turn dishwasher off
without draining.
To cancem a Delay and the cycle: (Cycle selector knob models}
. Turn the cycle knob to [}rain/OFF. The dishwasher
will drain, then turn off.
Or
. Turn the cycle knob to [}rain/OFF, press the START
button once. The dishwasher will turn off without
draining.
If 30 seconds elapse between setting the cycle and options and pressing the START/Cancel pad
or START button, the dishwasher will turn off.
12
Control Lock
The control touchpads can be locked to prevent
unwanted use. If this feature is activated between
cycles, the dishwasher cannot be operated until the controls are unlocked. If desired, the controls can be
locked after a cycle or delay has started.
Setting the Controm Lock:
1. Press the Heated Dry pad for three seconds.
2. An indicator light next to the lock graphic will
illuminate when the controls are locked.
To Cancem:
1. Press the Heated Dry pad for three seconds.
2. The indicator light will go off.
If a cycle or option pad is pressed after the controls have been locked, the indicator light next to the lock graphic will flash five times. On selected models with a countdown display, the display will flash an "L" simultaneously with the
lock indicator.
Option (selectmodels)
This option does not lock the door, only the dishwasher controls.
13
Lights/Display (, m otmo. m,
TIME REMAINING Display Shows approximate minutes remaining in a cycle. The symbol "2H" will appear when cycle time is greater
[select r_lodels:) based on each load's soil level, water tempelatule and selected options.
CLEAN Light Huminates at the end of the cycle and remains lit until the door has been open for 30 seconds
DRYING Light Illuminates during the entire db' period and goes out when the cycle is completed.
(select models] WASHING Light Illuminates during all rinse and wash portions of the cycle. On models with a cycle selector knob, the
(select r_lodels:) WASHING Light will remain illuminated during the entire cycie including dl%
HEATING DELAY Light
(select models:} Illuminates when cycle is being extended to heat the water.
SANITIZED Light Ilhminates at the end of the cycle when conditions have been met to achieve sanitization. The light wilI
(select models) remain lit until the door has been open for 30 seconds continuously.
than 99 minutes. Cycle times shown in the numericai dispiay (select models) will increase or decrease,
continuously.
° When Sanitize is selected, cycles are monitored to assure sanitization. The SANITIZED LightwiLLnot activate if sanitization
requirements are not met. This could happen if the cycle is interrupted, power failure occurs or incoming water temperature is below 120° F (49° F:).
° The CLEAN and SANITIZED indicator lights (select models) will not relight after a power failure until after the next cycle isrun.
Most taMeware, cookware and flatware can safdy be washed in your dishwasher. Check with the manufacturer.
Aluminum Yes, except anodized. High water temperature and detergents may affect finish.
Cast Iron No Seasoning will be removed, and iron will rust.
China/Stoneware hand-painted, painted or over-the-glaze patterns may fade. Gold leaf may discolor.
Crystal Yes, except antique ol Always check manufacturer's lecommendation befole washing. Some types of
Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.
Glass Yes A specialty glass called milk glass can yellow with repeated dishwasher washing.
Gold-Plated Flatware No Will discolor.
Pewter, Tin No
Plastics disposable plastic items, their capacity to withstand high water tempe_atures and detergents. Disposable
Stainless Steel Ye,s foods containing salt, vinegar, milk products ol juice could damage finish.
Sterling Silver or No, if has commelcial Only cycle if not washing immediately. Prolonged contact with food containing
Siiverpiate "darkening". salt, acid or sulfide (eggs, mayonnaise and seafood) could damage finish.
Yes, except antique or Always check manufacturer's recommendation before washing. Antique, hand-
delicate crystal, leaded crystal may etch with lepeated washings.
Yes, top rack, except Always check manufacturer's recommendation before washing. Plastics vary in
plastic items are not dishwashe_ safe fo_ this mason.
Run a Rinse Only cycle if not washing immediately. Prolonged contact with
Always check manufacturer's recommendation before washing. Run a Rinse
Commercial "darkening" may be removed by detergent.
Wooden Items No Wood may warp, crack or discolor.
14
General Recommendations
. The dishwasher interior is normally self-cleaning.
Periodically check the bottom of the dishwasher tub
to see if any large particles remain. Wipe the edge of the inner door liner to remove any
food soil splashes which occurred during loading. When cleaning the stainless steel exterior, always
wipe with the grain. Never use products containing cHorine bleach or citric acid.
The color from some tomato-based food soils may
occasionally adhere to various components of the dishwasher interior, causing temporary discoloration.
To minimize this:
Remove excess tomato-based food soils from
dishes before loading.
Run the Heavy Wash cycle when washing loads
containing tomato-based food soils.
. Be sure to use a dishwasher detergent that
contains chlorine to better fight staining.
Standard Exterior
Stainless Steel Exterior
Light to modelate Soft damp cloth and liquid spray cleaner. Do Not use
Daily cleaning and light soil Soft cloth or sponge and one of the following:
(semeetmodems}
Moderate to heavy soil Soft cloth or damp sponge and Bon AmY. Follow with
Streaks ol fingerplints/lestore shine Soft cloth and Stainless Steel Magic Splay_L
Discoloration Soft cloth or damp sponge and Cameo Stainless Steel
Interior Light to moderate Soft cloth or damp sponge.
Discoloration, or tomato-based stain Switch dishwashel detergent to chlorine-based product.
_Brand names are trademarks of the respective manufacturer. _Call 1-800-JENNAIR (1-800-536-6247) to oldeL
abrasive powders or cleaning pads.
Mild detergent and water
A solution of white vinegar and water
Formula 409 Glass and Surface Cleaner#,ol similal
multi-surface cleaner.
° De Net use products containing chloline bleach ol
citric acid.
Follow with rinse and d_%
rinse and dry.
Cleane¢. Rinse immediately and dry.
FIll detergent cup with a fresh-scented dishwasher detergent or baking soda and select the Normam
Wash cycle. Allow the dishwasher to complete the
cycle. Then turn the water supply off and drain the dishwasher. To drain, press the START/Cancem pad
once to activate the dishwasher. Press START/Cancem again to activate the drain (models with cycle selector
knob, turn the cycle selector knob to Drain/OFF}. Operate the drain twice to ensure most of the water is
removed. Last, disconnect the electrical supply and prop open the door.
When turning the water supply to the home off, the water shut off at the dishwasher must be turned off also.
15
CHECK THESE POINTS TO HELP SAVE YOU TiME AND MONEY.
Dishwasher will not fill ° Press the STARTiCanceU pad to start the dishwasher.
° Be sure door is htched secureUy. ° Be sure the water is turned on.
° Check that the pad is properly sebcted for a cycb. ° Check your home's chcuK breaker or fuse box.
° Check inbt hose for a kink. ° Check water vaUveinbt for sediment and clean if necessau%
Dishwasher wiil not drain/ Water in tub bottom
° if hooked up to a food waste disposer, be sure the knock-out is removed from
the disposer inbt.
° Check for food obstruction in the drain or disposer. ° Check drain hose for a kink.
° Check your home's circuit breaker or fuse box. ° Check that the cycle is completed.
Dishwasher adds water at ° This is normal The sensor (select models} in the pump must stay submerged so end of eycJe a short fill of water is added after the cycle's last drain.
Detergent cup is not empty ° Check that the cycle is completed.
° Be sure dispenser is not blocked. ° Use fresh detergent stored in a cool, dry place.
Dishwasher seems noisy
° A water valve hiss during fill is normal ° Water circulation sounds are normal
° A thumping sound may be a wash arm bumping an item that is extending
beyond the racks. Readjust load to avoid obstructing wash arm.
° Chopping or grinding sounds may be heard as the internal food disposer chops
hard items like fruit seeds, nuts, etc. ° Humming during the drain is normal ° A snap noise is the detergent cup lid hitting the door liner when the dishwasher
door is opened at the end of the cycle. This is normal ° Proper installation affects the noise level
CycJe takes too mong (Heating Delay Eight [select models]
stays on}
Dishwasher has an odor
, Super Scrub or Sanitize (select models] has been selected and the cycle is
extended to heat water. ° Check to see that the incoming water temperature is 120° F (49° C}.
®
Run dishes being held in the dishwasher through a Rinse Only cycle.
Many dishwasheus have a"new" smell when first installed. This wiii dissipate with use.
®
Dishwasher may not be draining properly. (See "Dishwasher Will Not Drain" section.}
For a strong odor, place baking soda in both sides of the detergent cup. Select
ChinaiCiTstal cycle and allow the water to circulate for about 10 minutes. InteiTupt
the cycle by unlatching the door and let it stand overnight. Restart the dishwasher
by latching the door and allow it to complete the cycle. Another alternative is to
use a dishwasher cleaning product such as Jet@ry Dishwasher CleaneP.
Dishwasher Beaks
Check that the dishwasher is level (Refer to the Installation instructions.} ° Suds can cause the dishwasher to overflow. Measure the detergent carefully and
use only detergents designed for use in a dishwasher. Less detergent is needed
in soft water. Try another brand of detergent if sudsing continues. , Follow directions closely on how to add a forgotten item (pg. 3]. , To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached.
*Brand names ale trademarks of the lespective manufacture1.
Cont.
IG
Displaytime suddenlydrops
or increases by several
minutes (select mode_s}
o This is normal when the Sensor Clean (select models} or Normal Wash cycle is
selected and the dishwasher decides to skip or add a drain and refill
_ndicator Eights flashing
Glasses are cloudy/spotted
Food soil remains on dishes
The countdown display (select models} flashes after a cycle is selected until the START/Cancel pad is pressed.
o The countdown display (select models} and the delay indicator flash after a
delay is selected until the START/Cancel pad is pressed.
o All active display indicatols flash if the door is opened during a running cycle or delay.
The cuFently selected cycle flashes if an attempt is made to change the cycle
after cycle "lockqn'.
o The lock indicator flashes and the countdown display (selected models} flashes
an "L" if a pad is pressed while the control lock is enabled.
o Select Extra Rinse (select models}. o Check water temperature, incoming water should be 120° F (49° C}.
Always use a rinse aid.
o Confirm that the cloudiness is removable by soaking the item in white vinegar
for approximately 5 minutes, if removed, the problem is due to hard water. Adjust detergent amount being used to match water hardness (pg. 9}. Be sure
detergent is fresh, stored properly and is a high quality brand.
o if cloudiness is not removable, it is etching. This is an erosion of the surface of
the glassware and can be caused by water that is too hot, from using too much
detergent or by prewashing. Detergent needs food soil to act upon. if etching has occuFed, the glassware is permanently damaged. To prevent further
etching, adjust the detergent amount to match the water hardness, stop prewashing, and use water heating options only when incoming water
temperature is below 120° F (49° C}.
o Check water temperature (pg 9}.
Run hot water at the sink before starting the dishwasher.
o Select Super Scrub option (select models}. o Check water hardness and adjust detergent amount accordingly (pg. 9}.
Use fresh detergent stored in a cool dry place.
o Select proper cycle for the soil level (pg. 10}.
Make sure the upper rack wash arm connector is correctly aligned in one of the water inlet hobs (pg. 8}.
Load items so they do not block the wash arms (pg. 3-7}.
o Load the utensil basket with knife handles up and spoon and fork handles
down through the slots in the covers.
o Do not place glasses over tines.
Prior to loading, scrape off burnt on foods and wipe the starchy film from
utensils used with pasta, rice and oatmeal These soils require more energy
than the rest of the load to clean.
_tems washed in the dishwasher or the dishwasher
tub itself are stained/ discolored
*Brand names are trademalks of the respective manufacturer. 17
Aluminum utensils or pans can leave marks when they rub against other items.
Leave a slight space between items.
iron deposits in the water can leave a yellow, brown or orange film on dishes orthe
dishwasher tub. A rust filter may be needed, check with a water treatment company.
o Separate silver or silver-plated silvelware from stainless steel These metals can
be damaged by contact with each other during washing.
Color from tomato sauces may adhere to the interior palls of the dishwasher
(pg. 15}. if light staining has occurred, leave the door open to oxidize the stain away. Change dishwasher detergent and be sure to use a dishwasher detergent
that contains chlorine to better fight staining.
Certain dishwasher detergents may stain silver. Try another brand of detergent.
Loading...
+ 42 hidden pages