Jenn-Air Attrezzi™ Blender
Model # JBL800
USER GUIDE
Congratulations on your purchase of a Jenn-Air Attrezzi™ Blender. Inspired by the Italian word for tools, Jenn-Air Attrezzi™ captures the European appetite for life – combining art, form and function.
Jenn-Air Attrezzi™.
For the love of cooking.
Table of Contents |
|
Safety Instructions ................................................................................................. |
1-3 |
Parts and Features................................................................................................. |
3-4 |
Assembling Your Blender ................................................................................... |
5-6 |
Operating Your Blender....................................................................................... |
6-8 |
Speed Control Guide................................................................................................. |
9 |
Care and Cleaning................................................................................................... |
10 |
Before You Call For Service ................................................................................. |
11 |
Recipes.................................................................................................................. |
12-15 |
Warranty/Customer Service........................................................................... |
16-17 |
Guide de l’utilisateur............................................................................................... |
18 |
Guía del usuario ....................................................................................................... |
36 |
Part No. 16022441 |
7/03 |
What You Need to Know About Safety Instructions
Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining or operating appliance.
Always contact your dealer, distributor, service agent or manufacturer about problems or conditions you do not understand.
Recognize Safety Symbols, Words, Labels
WARNING
WARNING – Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION
CAUTION – Hazards or unsafe practices which COULD result in minor personal injury.
IMPORTANT SAFEGUARDS
WARNING
When using electrical appliances, basic safety precautions should always be observed, including the following:
1.Read all instructions.
2.To protect against risk of electrical shock, do not immerse the cord, plug or blender power base in water or other liquids.
3.Close supervision is necessary when any appliance is used by or near children.
4.Unplug blender from outlet when not in use, before putting on or taking off parts, and before cleaning or taking apart the blender pitcher. Never put hands in blender pitcher or handle the blades when the appliance is plugged in. Never operate the blender without the pitcher fully assembled.
5.Avoid contacting moving parts.
6.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest authorized service
1
facility for examination, repair, electrical or mechanical adjustment. Call the Jenn-Air Customer Service Center at 1-866-982-3313 for assistance.
7.Using attachments not recommended or sold by the appliance manufacturer for use with this model, including canning jars or ordinary jars, is not recommended and may cause fire, electric shock or injury to persons.
8.Do not use the blender outdoors.
9.Do not let the cord hang over the edge of a table or counter. Do not let cord contact hot surfaces, including stove.
10.Keep hands and utensils out of pitcher while blending to reduce the risk of severe injury to persons or damage to the blender. A scraper may be used but must be used only when the blender is not running.
11.Flashing light indicates ready to operate. Avoid any contact with blades or moveable parts. When the blender is in the “ON” mode, and the touch control is illuminated, do not touch the blade assembly, interfere with blade movement or remove the pitcher lid. Accidentally touching a speed control may activate the blender.
12.Blades are sharp. Handle carefully.
13.To reduce risk of injury, never place the blade assembly on the power base without the pitcher properly attached.
14.Always operate blender with the lid in place.
15.Never leave blender unattended while running.
16.When blending hot liquids remove pitcher lid cap from lid. Beware of steam or hot vapor. When removing the lid, tilt lid slightly to direct steam away from skin. Keep hands and other exposed skin away from opening to prevent possible burns.
17. Do not use an extension cord with this blender.
WARNING
To reduce the risk of electrical shock or fire, do not take apart the blender power base. All repairs must be performed only by factory authorized personnel.
This product is designed for household use only. Do not use blender for other than intended purpose.
2
WARNING
Electrical Grounding Instructions – This appliance is equipped with a (3-prong) grounding plug for your protection against shock hazard and it should be plugged directly into a properly grounded receptacle. Do not cut or remove the grounding prong from this plug. If the plug fails to fit into an existing outlet, contact a qualified electrician to update the outlet.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
Parts and Features
1 2
3
5
6
7
8
9
3
1.Pitcher Lid Cap
This center portion of the pitcher lid may be removed, allowing ingredients to be added during use. (Be sure to check size of food load in the blender and the speed setting prior to removing cap.)
2.Pitcher Lid
Seals the top of the pitcher jar.
3.Pitcher Jar
The 72-ounce glass pitcher jar has a unique bulb-shaped design that offers outstanding blending performance. The pitcher is beautiful enough to go directly from the countertop to the serving table.
4.Pitcher Gasket
This seals the bottom of the pitcher jar to the blade base.
5.Blade Base
The wider bottom of the pitcher jar accommodates a larger blade for improved rollover, increased fluid movement and outstanding blending.
6.Base Ring
The base ring screws onto the bottom of the pitcher jar, holding the pitcher gasket and blade base in place.
7.Blender Power Base
The power base features a 500-watt motor and innovative touch controls. The pitcher locks onto the power base with a simple quarter turn for safe, no-mess operation.
8.Control Panel
The easy-to-use touch controls feature a range of five powerful speeds, as well as an ice crush mode and a pulse option. The controls are activated with the touch of a finger.
9.Detachable Power Cord
The detachable power cord is interchangeable with other Jenn-Air Attrezzi™ small appliances.
4
Assembling Your Blender
1.Carefully remove all blender parts from the packaging.
2.Place the blender power base on a solid, level surface.
3.Before first use, wash the pitcher jar, pitcher
lid, pitcher lid cap, pitcher gasket, blade base, and base ring in hot, soapy water. Rinse and dry. The pitcher jar is dishwasher safe. The pitcher lid, pitcher lid cap, base ring, and blade base are all top-rack dishwasher safe.
4.Carefully place the pitcher gasket over the blade base, while keeping fingers away from the blades.
5.Turn the pitcher jar upside down.
6.Using caution, place the blade base and pitcher gasket into the bottom opening of the pitcher jar.
7. Twist the base ring onto bottom of pitcher jar, making sure it threads evenly and secures the pitcher gasket and blade base in place. The base ring should be tightened hand-tight onto the pitcher jar. Do not over-tighten.
8. Turn the pitcher jar right side up and place it on top of the blender power base and turn clockwise to lock the pitcher in place.
9.Insert the pitcher lid cap into the pitcher lid and tighten it by turning clockwise. Place the pitcher lid onto the pitcher jar.
10.Plug the detachable power cord into the blender power base and a properly grounded 3-prong electrical outlet. The blender is now ready to use.
WARNING
Electrical Shock Hazard – Plug into grounded outlet. Do not remove ground prong. Do not use an adapter. Failure to follow these instructions can result in death or electrical shock.
5
Removing pitcher from base
1. Make sure the blender controls are set to “OFF” and the power cord is unplugged.
2.Turn the pitcher counterclockwise and lift the pitcher up and off the base.
3. Do not unscrew the base ring from the pitcher jar until you are ready to remove the blade assembly. Loosening it will cause leaking.
Note
• Be sure to operate your blender on a clean, dry, sturdy surface.
Operating Your Blender
1.Make sure the touch controls are SET TO “OFF” and the power cord is unplugged.
2.Place the assembled PITCHER ON TOP OF BLENDER BASE and turn clockwise to lock the pitcher in place.
3.LOAD BLENDER with food to be blended and place the lid securely on the pitcher jar.
4.TOUCH THE “ON” PAD on the control panel.
ON OFF
The “ON” pad should illuminate and the WARNING light will flash to indicate that the blender is ready to operate.
STIR |
CHOP |
MIX |
PUREE |
LIQUIFY |
||
|
|
|
CRUSH |
PULSE |
|
|
|
W |
|
|
|
YTO |
|
|
AR |
NIN |
|
|
|
|
|
|
|
G: |
FLASHING LIG HT INDICATES ES |
|
|
|
|
|
OPERATE DO NO TTOUCHBLAD |
|
||
5.TOUCH ONE OF THE 5-SPEED PADS. Refer to the “Speed Control Guide” in this manual for suggested settings. Refer to the “Pulse Mode” and “Ice Crushing Mode” sections in this manual for use of those controls.
WARNING
To avoid risk of injury, be sure that the blender is fully off with all control panel lights off before opening the blender and scraping the sides of the pitcher. Never attempt to scrape the sides of the pitcher while the blender is operating or with any of the control panel lights illuminated.
6
Turning the Blender Off
While the blender is operating, touch the “OFF” pad on the control panel or touch the active speed setting pad a second time and the blender will stop. The “ON” pad will still be illuminated and the WARNING light will flash to indicate the blender is ready to operate again. Press the “OFF” pad a second time to completely turn the blender off.
Auto Shut-off
•The blender will automatically shut off if allowed to stand with no control pads pressed for 10 minutes.
•If two speed settings pads are accidentally touched at the same time, the blender will shut off.
Pulse Mode
1.Touch the “ON” pad on the control panel. The “ON” pad will illuminate and the WARNING light will flash to indicate that the blender is ready to operate.
2.Touch the “pulse” pad.
3.Select a speed setting and touch the corresponding pad on the control panel.
4.The blender will operate only while you are touching the speed setting pad.
Note
•When unsure about the appropriate speed setting, try pulsing to test various speeds.
7
Ice Crushing Mode
1.Load ice cubes in the blender pitcher, making sure to use ice that is thoroughly frozen. Break up any large chunks of ice.
2.Touch the “ON” pad on the control panel. The “ON” pad will illuminate and the WARNING light will flash to indicate that the blender is ready to operate.
3.Touch the “CRUSH” pad on the control panel. The blender will automatically operate in short bursts to crush the ice.
4.Once the ice is crushed, touch the “OFF” pad on the control panel.
Using the removable pitcher lid cap
1. While blender is off, remove pitcher lid cap by holding the pitcher jar and pitcher lid down with one had and twisting and lifting the pitcher lid cap with the other hand.
2.Use the small opening in the lid to add ingredients to the blender while the blender is running. Use caution and blend on low speed while pitcher lid cap is removed.
CAUTION
Be cautious when blending hot foods, as steam or hot vapor can burn skin when the lid is removed.
Use the feeder in the lid to vent steam or hot vapor, however be sure to open the lid gradually and direct steam or hot vapor away from hands, face and other exposed skin. Use low speeds and smaller quantities when mixing hot foods to prevent spattering.
8
Speed Control Guide
The following speed control guide provides suggested settings for your blender. If in doubt, start on a lower setting and try pulsing to test out various speeds.
Item |
Setting |
|
|
Baby food ingredients |
puree |
|
|
Blended ice drink |
crush |
|
|
Bread |
chop |
|
|
Coffee beans |
liquefy |
|
|
Crackers |
chop |
|
|
Crushed ice |
crush |
|
|
Fruit juice from frozen concentrate |
mix |
|
|
Milk powder & water |
liquefy |
|
|
Nuts |
chop |
|
|
Oatmeal |
puree |
|
|
Pancake batter |
mix |
|
|
Salad dressing |
mix |
|
|
Sauces |
stir |
|
|
Smoothies |
liquefy |
|
|
Tips:
The “pulse” mode can be used with any speed setting. Simply touch the “pulse” pad and then touch the desired speed setting.
When crushing ice, be sure to use ice cubes that are frozen solid and break up any large chunks.
If blending a mixture of liquid and solid ingredients, add the liquid ingredients to the blender first and then add the solids, unless the recipe states otherwise.
9
Care and Cleaning
WARNING
Injury hazard. Unplug blender before cleaning. Failure to do so can result in injury.
1.Touch the “OFF” pad to set the blender into its full-off state. Unplug the power cord.
2.Position blender pitcher over a sink to catch any remaining ingredients in the pitcher while taking it apart to clean.
3.Unscrew the base ring from the base of the pitcher.
4.Carefully disassemble the pitcher gasket and the blade base, keeping fingers away from sharp edges of the blades.
5.All of the pitcher parts should be washed in warm, soapy water. The pitcher jar is dishwasher safe. The pitcher lid, pitcher lid cap, base ring, and blade base are all top-rack dishwasher safe. The pitcher gasket can be washed in warm, soapy water.
6.Wipe down the blender power base, including the glass touch controls with a damp cloth. DO NOT immerse the blender base in water.
10
Before You Call For Service
Problem |
Possible Solution |
|
|
The blender will |
Check the power cord to make sure it is |
not start. |
securely fastened into the blender and |
|
into the electrical outlet. |
|
Make sure the “ON” pad is illuminated. |
|
Next, touch the desired speed setting. |
|
Avoid touching two speed settings at |
|
once since this will cause the blender to |
|
turn off. |
|
|
The blender is |
Make sure the pitcher lid is securely |
spattering ingredients |
fastened into the pitcher jar before |
outside the blender |
blending. |
pitcher jar. |
If the pitcher lid has been removed, |
|
|
|
make sure the blender is set on a low |
|
setting to avoid spattering. |
|
The blender may be overloaded. |
|
Remove some of the contents and |
|
continue blending. |
|
|
The blender is leaking |
Make sure the pitcher gasket is |
around the bottom |
positioned between the pitcher jar and |
of the pitcher. |
the blade base. |
|
Check to see if the base ring is securely |
|
screwed into place and aligned evenly |
|
around the base of the pitcher jar. |
|
|
The blender motor |
Check to make sure the blender isn’t |
is bogging down. |
overloaded with dense foods. |
|
If so, break into smaller pieces. |
|
When using the ice “crush” mode, be |
|
sure to use solidly frozen ice cubes and |
|
break up any large chunks of ice. |
|
|
The blender wobbles |
Make sure the small pads on the feet of |
on the work surface. |
the blender are all snugly pushed in. |
|
Check to see if the work surface is level. |
|
|
11
Recipes
Roasted Yellow Pepper Soup
The Mediterranean yellow color of this soup makes it a perfect choice as the first course for a late summer dinner. With its rich, mellow flavor, it will be appreciated year around.
1 medium red potato, peeled and cut into 1" cubes 2 stalks celery, coarsely chopped
1 carrot, peeled and coarsely chopped
1 small onion, peeled and coarsely chopped
1 clove garlic, minced
6 sweet yellow bell peppers, seeded and cut into 1" chunks 2 tablespoons extra virgin olive oil
6 cups chicken stock
1 teaspoon green peppercorns
1 cup heavy cream
salt and pepper, to taste 8 leaves of fresh basil
Place potato, celery, carrot, onion, garlic and yellow bell pepper pieces on an oven-proof baking tray. Drizzle with olive oil. Bake at 400° F. for 40-45 minutes (Convect Roast 30-35 minutes), or until tender. Cover loosely with foil and set aside to cool slightly (approximately 20 minutes).
In a large soup pot, bring chicken stock to a boil. Stir in green peppercorns. Reduce heat to simmer.
Set blender to “puree” and process the roasted vegetables in blender for 20-25 seconds or until smooth. Stir puree into the simmering chicken broth. Stir in heavy cream and mix well. Add salt and pepper to taste. Do not allow soup to boil. Serve immediately with fresh basil leaf garnish.
Serves 8.
12
Ricotta and Pine Nut Tart with Balsamic Strawberries
Enjoy this delightful tart sprinkled with pine nuts and drizzled with strawberries. The filling is mixed in the blender to create a creamy texture.
Pastry crust:
2 cups all-purpose flour
1⁄2 cup sugar
1⁄3 cups pine nuts, toasted and finely chopped 12 tablespoons unsalted butter, melted
Filling:
11⁄2 cups sugar
1 cup water
6 ounces cream cheese
1 cup ricotta cheese
3 egg yolks
2 whole eggs
1⁄4 cup pine nuts, whole
Balsamic Strawberries:
2 pints fresh strawberries
2 tablespoons sugar
1 tablespoon top quality Balsamic vinegar
Pastry Crust:
In a small bowl, mix flour, sugar and chopped pine nuts. Add melted butter and mix gently.
Press mixture into bottom and about 1" up the sides of a 10" spring form pan. Chill for ten minutes. Begin making the sugar/water mixture for the filling. Place aluminum foil over the pastry and fill with pie weights, dry beans or rice. Bake at 375° F (Convect Bake 350° F) for 15 minutes. Remove foil and pie weights, then bake an additional 10 minutes, or until golden brown. Cool completely.
13
Filling:
In a small saucepan, bring water and sugar to a boil. Boil until sugar is completely dissolved, about 4 minutes. Transfer to container with a pour spout and allow to cool 20 minutes.
Add cream cheese, ricotta cheese, egg yolks and whole eggs to blender pitcher. Cover with lid and mix 5 seconds. Turn blender off and scrape sides. Resume mixing for 15 seconds or until smooth. Turn blender off. Remove the pitcher lid cap. Set blender to “stir” and with the blender running, add the sugar syrup slowly.
Pour the cheese mixture into the prepared crust. Sprinkle the whole pine nuts over the top. Return to oven and bake the tart for 40-45 minutes, or until golden but still a bit soft in the middle. Cool. Serve topped with Balsamic Strawberries.
Balsamic Strawberries:
Clean, hull and slice the strawberries. Place in a shallow pan and sprinkle with sugar. Cover tightly with plastic wrap. Allow to stand at room temperature for 30 minutes. Shake occasionally.
Sprinkle with balsamic vinegar, shake pan to distribute flavor and allow to stand at room temperature for 30 more minutes.
Serves 8.
14
Tiramisu Cream Smoothie
This taste of Italy blends flavors of tiramisu into a refreshing ice cream drink. Topped with whipped cream and chocolate cookie crumbs, this drink is a sure party favorite.
1 tablespoon Kahlua
2 tablespoons espresso
2 tablespoons heavy cream or milk
3 tablespoons chocolate syrup
1 pint (2 cups) vanilla ice cream Whipped cream
Chocolate cookie crumbs
Pour Kahlua, espresso, cream, chocolate syrup and ice cream into blender. Set blender to “liquefy” and pulse for 15 to 20 seconds or until ingredients are smooth and creamy. Pour into cocktail glasses. Garnish with whipped cream and cookie crumbs.
Makes 2 6-ounce servings.
Strawberry Ice
This refreshing icy drink is perfect on a warm summer day.
Add a splash of rum and garnish the rim of the glass with a strawberry for a festive party cocktail.
1 16-ounce container frozen sweetened, sliced strawberries, thawed 4 cups ice cubes
Place undrained strawberries in blender; add ice cubes. Combine strawberries and ice cubes on “crush” setting for 35-45 seconds or until all ice is crushed. Serve.
Makes 4 8-ounce servings.
15
Warranty/Customer Service
Jenn-Air 1 Year Hassle-Free Replacement
Warranty
Jenn-Air stands behind the high quality of our blenders by offering a one-year hassle-free replacement warranty. If your blender should fail within the first year of ownership and upon inspection by Jenn-Air is proven defective, the blender will be replaced without charge. Jenn-Air will arrange for it to be returned free of charge. Jenn-Air will also arrange delivery of an identical or comparable replacement to your door free of charge.
THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE MADE BY JENN-AIR OR ARE AUTHORIZED TO BE MADE WITH RESPECT TO THE PRODUCT.
What Is Not Covered By This Warranty:
1.Conditions and damages resulting from any of the following:
a.Any repair, disassembly, modification, alteration, or adjustment not authorized by Jenn-Air.
b.Misuse, abuse, accidents, unreasonable use, negligence or failure to follow the Jenn-Air instructions.
c.Incorrect electric current, voltage or supply other than listed on the product.
d.Improper setting of any control.
2.Warranty is void if the original serial numbers have been removed, altered or cannot be readily determined.
3.Products purchased for commercial or industrial use.
4.Consequential or incidental damages sustained by any person as
aresult of any breach of these warranties. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not apply.
16
Loading...