Jenn-Air JBC7624BS0 Owner’s Manual

JENN-AIR™ BUILT-IN COFFEE SYSTEM

SYSTÈME INFUSEUR À CAFÉ JENN-AIR

™

W10629090B

Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à

Model/Modèle JBC7624BS

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.

Guide d'utilisation et d'entretien

www.jennair.ca.

Table of Contents/Table des matières ...................2

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

COFFEE SYSTEM SAFETY............................................................2

PARTS AND FEATURES................................................................4

BEFORE USING THE COFFEE SYSTEM......................................5

COFFEE SYSTEM USE ..................................................................6

Settings ........................................................................................6

Switching On and Preheating ......................................................8

Making Coffee or Espresso Using Coffee Beans........................8

Changing the Amount of Coffee ..................................................9

Adjusting the Coffee Grinder .....................................................10

Making Espresso with Ground Coffee.......................................10

Making Cappuccino...................................................................10

Dispensing Hot Water ................................................................12

COFFEE SYSTEM CARE .............................................................13

General Cleaning........................................................................13

Vacation or Storage ...................................................................15

Switching Off the Coffee System...............................................15

TROUBLESHOOTING ..................................................................16

ASSISTANCE OR SERVICE.........................................................18

In the U.S.A. ...............................................................................18

In Canada ...................................................................................18

WARRANTY ..................................................................................19

COFFEE SYSTEM SAFETY

TABLE DES MATIÈRES

SÉCURITÉ DU SYSTÈME INFUSEUR À CAFÉ..........................21

PIÈCES ET CARACTÉRISTIQUES ..............................................22

AVANT D’UTILISER LE SYSTÈME INFUSEUR À CAFÉ............23

UTILISATION DU SYSTÈME INFUSEUR À CAFÉ .....................24

Réglages.....................................................................................24

Mise en marche et préchauffage ...............................................26

Préparation de café ou d’expresso avec des grains de café....27

Modification de la quantité de café............................................28

Réglage du moulin à café...........................................................28

Préparer de l’expresso avec du café moulu..............................28

Préparer du cappuccino.............................................................29

Distribution d’eau chaude ..........................................................30

ENTRETIEN DU SYSTÈME INFUSEUR À CAFÉ........................31

Nettoyage général ......................................................................31

Vacances ou remisage...............................................................33

Arrêt du système infuseur à café ...............................................33

DÉPANNAGE.................................................................................33

ASSISTANCE OU SERVICE.........................................................35

Au Canada..................................................................................35

GARANTIE.....................................................................................35

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury to persons when using the appliance, follow basic precautions,

including the following:

WARNING:

SAVE THESE INSTRUCTIONS

■ Read all instructions before using the appliance.

■ Do not touch hot surfaces. Use handles or knobs.

■ To protect against fire, electric shock and personal injury

do not immerse cord, plugs, or appliance in water or other liquids.

■ The appliance is not intended for use by young children or

infirm persons without supervision.

■ Unplug from outlet when not in use and before cleaning.

Allow to cool before putting on or taking off parts, and before cleaning.

■ Do not operate any appliance with a damaged cord or

plug, or after appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest authorized service center for examination, repair or adjustment.

■ The use of accessory attachments not recommended by

the appliance manufacturer may result in fire, electric shock, or personal injury.

■ Do not use outdoors.

■ Do not let cord hang over edge of table or counter, or

touch hot surfaces.

■ Do not place on or near a hot gas or electric burner, or in a

heated oven.

■ Always switch the appliance off, then plug cord into the

wall outlet. To disconnect, turn the appliance off, then remove plug from wall outlet.

■ Do not use appliance for other than intended household

use.

■ Use extreme caution when using hot steam.

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

PARTS AND FEATURES

This manual covers several models. The coffee system you have purchased may have some or all of the items listed. The locations and appearances of the features shown here may not match those of your model.

Front View:

Rear View:

A. Cup tray B. Service door C. Coffee feed D. Coffee grounds container

E. Brewing unit

F. On/standby button G. Cup tray lights H. Control panel

I. Hot water and steam nozzle

J. Water tank

K. Coffee spout (height-adjustable)

L. Drip tray

A. Main on/off switch B. Grinding coarseness adjustment knob C. Coffee bean container D. Coffee bean container lid

E. Ground coffee funnel cap

F. S c o o p G. Scoop compartment H. Ground coffee funnel feed

I. Power supply cable

J. Terminal board

K. Storage tray

Milk and Accessories Container:

A. Milk intake tube B. Frothed milk spout C. Milk frother

BEFORE USING THE COFFEE SYSTEM

Coffee has been used to factory test the machine. It is completely normal for there to be traces of coffee in the mill.

Customize water hardness as soon as possible. See “Water Hardness” in the “Settings” section.

IMPORTANT: Complete the following steps before the coffee system is used for the first time.

1. Check that the hot water spout is installed. If it is not, insert

the hot water spout into the hot water and steam nozzle.

D. Milk frother pointer

E. Clean button F. Milk container handle

G. Hot water spout

4. After 5 seconds, “FILL TANK!” will be displayed. Remove the

water tank, rinse and fill to the MAX line with fresh water. Replace the water tank.

A. Water tank

5. “HOT WATER Press OK” will be displayed. Place a cup

underneath the hot water spout. Press OK. After a few seconds, hot water will be dispensed.

A. Hot water and steam nozzle B. Hot water spout

2. Turn on the coffee system.

3. The available languages will scroll automatically. Wait until

“Press OK to install ENGLISH” is displayed. Press and hold OK.

A. Hot water spout

6. “TURNING OFF Please wait...” will be displayed. The coffee

system will turn off.

7. Slide the coffee system forward using the handles as shown

in the following illustration.

A. Handles

8. Open the coffee bean container lid, fill the coffee bean

container with coffee beans and close the lid. IMPORTANT: Do not place ground coffee, freeze-dried

coffee, caramelized coffee or foreign objects into the coffee bean container, as they could damage the machine.

A. Coffee bean container

9. Push the coffee system back into the housing. It is now ready

for normal use.

NOTE: When first using the coffee system, you need to make 4-5 cups of coffee and 4-5 cappuccinos before the coffee system gives good results.

NOTE: Each time the machine is turned on using the main On/Off switch, it runs a self-diagnosis function and then goes into standby mode. To turn the machine on again, press the On/ Standby button to the left of the coffee spout. See the illustration in the “Parts and Features” section.

COFFEE SYSTEM USE

A. 1 Coffee B. 2 Coffee C. Menu

D. Strength E. Display F. Down arrow key

G. Up arrow key H. Hot water

I. Cappuccino

Settings

You can control several settings through the Settings Menu: Rinsing, Beep, Statistics, Default Values, Water Hardness, Auto-Off, Coffee Temperature, Descaling, Auto-Start, Language and Adjust Time.

To access the Settings Menu, press MENU. To exit the Settings Menu, press MENU again.

Rinsing

This function is used to rinse the coffee spout or preheat the brewing unit if more than 2 minutes have passed since the machine was last preheated. Hot water from the rinse cycle can be used to preheat a small cup of coffee.

1. Press MENU.

2. Press the up and down arrow keys until “RINSING” is

displayed. Press OK.

3. “OK to confirm” will be displayed. Press OK.

4. “Please wait...” and a progress bar will be displayed. 1 oz

(30 mL) of hot water will run into the drip tray. NOTE: If desired, you can place a small cup beneath the

coffee spout. The hot water will warm the cup. Empty the hot water before using the cup for coffee.

Beep

The coffee system is factory-set with tones enabled, but they can be disabled.

1. Press MENU.

2. Press the up and down arrow keys until “BEEP Enabled” is

displayed. Press OK.

3. “BEEP Disable?” will be displayed. Press OK to deactivate the

tones.

4. Press MENU to exit the menu. To reactivate the tones, repeat steps 1-4.

Statistics

This function allows you to view the machine statistics.

1. Press MENU.

2. Press the up and down arrow keys until “STATISTICS” is

displayed. Press OK.

J. OK

K. Size

3. Press the up and down arrow keys to see:

■ Total cups of coffee made

■ Total liters of water used

■ Total number of descalings

■ Total cups of cappuccinos made

4. Press MENU once to exit the Statistics menu. Press MENU

again to exit the main menu.

Default Values

This function will restore all settings to the factory-set defaults.

1. Press MENU.

2. Press the up and down arrow keys until “DEFAULT VALUES”

is displayed. Press OK.

3. “OK to confirm” will be displayed. Press OK.

4. “Restore” will be displayed for a few seconds. All settings will

be reset to default.

5. Press MENU to exit the menu.

Water Hardness

It is important to set the correct water hardness for proper descaling.

1. Remove the “Total hardness test” water hardness strip (found

in the bag containing literature) from its packaging.

2. Immerse the strip fully in a cup of water for a few seconds.

3. Remove the strip and wait approximately 30 seconds until it

changes color and red squares appear on the strip.

4. Press MENU.

5. Press the up and down arrow keys until “WATER

HARDNESS” is displayed. Press OK.

6. Press the up and down arrow keys to select the number of

dots corresponding to the number of red squares that have formed on the test strip. For example, if the test strip shows 3 red squares, select .

7. Press OK.

Auto-Off

Descaling

If “DESCALE!” is displayed, the coffee system needs to be descaled.

NOTE: Failure to descale the machine regularly can result in decreased product performance and may result in product damage.

1. When the machine is ready for use, attach the hot water

spout to the hot water and steam nozzle.

A. Hot water and steam nozzle B. Hot water spout

2. Press MENU.

3. Press the up and down arrow keys until “DESCALING” is

displayed. Press OK.

4. “DESCALING OK to confirm” will be displayed. Press OK.

5. “Add Descaler Press OK” will be displayed. Remove the

water tank and empty the contents. In the water tank, pour in the contents of a packaged descaler and water, following the manufacturer’s instructions.

IMPORTANT: Do not use vinegar to descale the coffee system. Use a packaged descaling agent. When using a descaling agent, follow the directions on the package for the recommended amounts of descaling agent and water.

Replace the water tank.

The coffee system is factory-set to go into standby mode automatically after 30 minutes of inactivity.

1. Press MENU.

2. Press the up and down arrow keys until “AUTO-OFF” is

displayed. Press OK.

3. Press the up and down arrow keys until the desired period of

time before the coffee system goes into standby mode is selected: 30 minutes, 1 hour or 2 hours.

4. Press OK.

5. Press MENU to exit the menu.

Coffee Temperature

The temperature of the brewed coffee can be changed.

1. Press MENU.

2. Press the up and down arrow keys until “COFFEE

TEMPERATURE” is displayed. Press OK.

3. Press the up and down arrow keys until the desired coffee

temperature is selected: low, medium or high.

4. Press OK to confirm the temperature chosen.

5. Press MENU to exit the menu

A. Water tank

6. Place a 2 qt (2 L) or larger container underneath the hot water

spout.

7. Press OK. “DESCALING UNDERWAY” will be displayed and

the descaling solution will be dispensed.

8. The descaling program will automatically alternate between

runoffs and pauses.

9. “RINSING FILL TANK!” will be displayed. Empty the descaling

runoff and replace the container.

10. Remove the water tank and empty the contents. Rinse the

water tank thoroughly to remove all traces of descaler. Add 3 cups (710 mL) water to the water tank.

11. Replace the water tank. “RINSING Press OK” will be

displayed. Press OK.

12. “RINSING” will be displayed. Hot water will be dispensed.

13. “RINSING COMPLETE Press OK” will be displayed. Press OK.

14. “FILL TANK!” will be displayed. Remove the water tank, fill it

with clean water and replace the tank. The descaling program is complete, and the machine is ready

to prepare coffee.

NOTE: If the descaling cycle is interrupted before it has been completed, it will need to be restarted from the beginning.

Auto Start

The coffee system can be set to switch on automatically at a preset time.

NOTE: The internal clock must be set before activating Auto Start. See “Setting the Clock” in this section.

To Activate Auto Start:

1. Press MENU.

2. Press the up and down arrow keys until “AUTO-START

Disabled” is displayed. Press OK.

3. “AUTO-START Enable?” will be displayed. Press OK.

“AUTO-START 07:30” will be displayed. Press the up and down arrow keys until the desired hour is displayed. Press OK.

5. Press the up and down arrow keys until the desired minute is

displayed. Press OK.

6. Press OK. The display will show “AUTO-START Enabled.”

7. Press MENU to exit the menu. To Change Auto Start while Enabled:

1. Press MENU.

2. Press the up and down arrow keys until “AUTO-START

Enabled” is displayed. Press OK.

3. Press the up and down arrow keys until “ADJUST TIME” is

displayed. Press OK.

4. “AUTO-START XX:XX” will be displayed. Press the up and

down arrow keys until the desired hour is displayed. Press OK.

5. Press the up and down arrow keys until the desired minute is

displayed. Press OK.

6. Press OK. The display will show “AUTO-START Enabled.”

7. Press MENU to exit the menu. To Deactivate Auto Start:

1. Press MENU.

2. Press the up and down arrow keys until “AUTO-START

Enabled” is displayed. Press OK.

3. “AUTO-START Disable?” will be displayed. Press OK. The

display will show “AUTO-START Disabled.”

4. Press MENU to exit the menu.

Setting the Clock

The coffee system has an internal 24-hour clock.

1. Press MENU.

2. Press the up and down arrow keys until “ADJUST TIME” is

displayed. Press OK.

3. Press the up and down arrow keys until the correct hour is

displayed. Press OK.

4. Press the up and down arrow keys until the correct minute is

displayed. Press OK.

5. Press MENU to exit the menu.

Switching On and Preheating

Every time the coffee system is switched on, it will perform an automatic preheat and rinse cycle that cannot be interrupted. The coffee system is ready for use after this cycle is complete.

To switch the coffee system on, press the On/Standby button once. “HEATING UP Please wait...” will be displayed. There may be some hot water runoff through the coffee spout.

When “MEDIUM CUP Standard taste” is displayed, the coffee system is ready for use.

To preheat the coffee system again, see “Rinsing” in the “Settings” section.

Making Coffee or Espresso Using

Coffee Beans

The coffee system is factory-set to make a standard-strength medium cup of coffee. The strength of the coffee can be changed by pressing Strength until the desired strength is displayed: extra-mild, mild, standard, strong, extra-strong or ground.

NOTE: Do not use ground coffee unless the ground coffee option is selected.

To change the amount of coffee dispensed for each cup size, see the “Changing the Amount of Coffee” section.

If the display shows “FILL TANK!” the water tank must be filled. The water tank may still contain some water; this is normal.

To Make Coffee:

1. Make sure there are coffee beans in the coffee bean

container.

2. Place 1 or 2 cups under the coffee spouts as shown in the

following illustration.

Language

The coffee system language can be changed.

1. Press MENU.

2. Press the up and down arrow keys until “LANGUAGE” is

displayed. Press OK.

3. Press the up and down arrow keys until the correct language

is displayed.

4. Press OK.

5. Press MENU to exit the menu.

For a creamier coffee, lower the coffee spout as near as possible to the cups.

One cup Two cups

A. Coffee spout

3. Press SIZE to select the size of the coffee cup: espresso,

small cup, medium cup, large cup or mug.

4. Press 1 COFFEE to make 1 cup of coffee or 2 COFFEE to

make 2 cups of coffee.

5. The coffee system will grind the coffee beans and dispense

the coffee. After the preset quantity of coffee has been dispensed, the coffee system will automatically stop and empty the coffee grounds into the grounds container.

NOTE: The coffee system can be interrupted at any time by pressing the 1 Coffee or 2 Coffee button again.

6. After a few seconds, the coffee system will be ready for use

again.

7. To switch off the coffee system, press the On/Standby

button. The coffee system will run an automatic rinse cycle and then go into standby mode.

If the coffee runoff is too slow or incomplete, or if the runoff is too quick and the coffee is not creamy enough, see the “Adjusting the Coffee Grinder” section.

Do not remove the water tank during the coffee runoff. If the water tank is removed, the coffee system cannot make coffee and will display “FILL TANK!” Check the water level in the tank and replace it. To restart the coffee system, press OK. “HOT WATER Press OK” will be displayed. Press OK. Water will run off from the spout for approximately 30 seconds. After the runoff completes, the coffee system will return to the programmed standard settings.

The coffee system may require you to repeat the operation several times to eliminate any air in the water line.

Tips for Hotter Coffee:

■ Run a Rinse cycle before brewing coffee. See “Rinsing” in the

“Settings” section.

■ Do not use very thick cups as they will absorb the heat unless

preheated.

■ Preheat all cups by rinsing them with hot water. See “Rinsing”

in the “Settings” section.

To C le an :

After every 14 cups of coffee made, the drip tray needs to be cleaned and the coffee grounds container emptied.

1. Open the service door on the front by pulling the coffee

spout.

2. Remove the drip tray and clean it. NOTE: When cleaning the coffee system, always fully remove

the drip tray.

A. Coffee grounds container B. Drip tray

3. Empty the coffee grounds container and replace it. NOTE: Every time the drip tray is removed, the coffee

grounds container must be emptied. Failure to do so may clog the coffee system.

4. Replace the drip tray and close the service door.

Changing the Amount of Coffee

The coffee system is factory-set to automatically deliver approximately the following amounts of coffee:

■ Espresso: 1 oz (30 mL)

■ Small cup: 1½ oz (45 mL)

■ Medium cup: 2 oz (60 mL)

■ Large cup: 3 oz (90 mL)

■ Mug: 4 oz (120 mL)

These settings can be adjusted up to 6 oz (180 mL). NOTE: The 2 Coffee button can be used to dispense twice as

much coffee as the 1 Coffee button even with custom settings. If you wish to return to the original settings, see “Default Values” in the “Settings” section.

1. Press SIZE until the display shows the desired coffee size.

2. Place your cup beneath the coffee spout. Press and hold

1 COFFEE until “PROGRAM QUANTITY” is displayed. NOTE: The coffee system will begin dispensing coffee before

“PROGRAM QUANTITY” is displayed.

3. Press 1 COFFEE again to stop the runoff and save the desired amount of coffee for the size.

The machine is now reprogrammed and ready for use.

A. Coffee spout B. Service door

Adjusting the Coffee Grinder

The coffee grinder is factory-set and does not require adjustment. If coffee runoff is too fast or too slow, the grinding coarseness can be adjusted.

NOTE: The grinding coarseness adjustment knob can be turned only while the grinder is in operation.

A. Grinding coarseness adjustment knob

For slower runoff and creamier coffee, turn the knob 1 click counterclockwise (finer ground coffee).

For faster runoff, turn the knob 1 click clockwise (coarser ground coffee).

3. Lift the small central lid, pour one scoop of ground coffee into the funnel.

NOTE: Only use ground coffee meant for espresso coffee machines.

A. Center funnel

NOTE: Use only the scoop provided. Do not add more than one scoop of ground coffee.

4. Close the central lid. Push the coffee system back into the housing and continue with Step 2 in the “Making Coffee or Espresso Using Coffee Beans” section.

NOTE: Only one cup of coffee can be made at a time with ground coffee. Do not use 2 COFFEE.

To deactivate the ground coffee function, press STRENGTH again.

A. Counterclockwise for finer grind B. Clockwise for coarser grind

Making Espresso with Ground

Coffee

1. Press STRENGTH repeatedly until “Ground” is selected.

2. Slide the coffee system forward using the handles as shown

in the following illustration.

Making Cappuccino

1. Press STRENGTH until the desired strength is selected.

2. Twist the milk container lid clockwise and lift up to remove it.

3. Fill the container with approximately ½ cup (100 mL) of milk

for each cappuccino you want to make. Do not fill above the MAX line on the milk container. For best results, use cold skim or 2% milk.

A. Handles

4. Make sure the milk intake tube is properly inserted into the

A B

rubber washer, then replace the milk container lid.

A. Milk intake tube

B. Rubber washer

5. Position the milk frother pointer on the milk container lid

between the words “Cappuccino” and “Caffelatte.” Move the pointer toward “Caffelatte” for a lighter froth and toward “Cappuccino” for a thicker froth.

A. Hot water and steam nozzle B. Milk container

7. Place a cup under the coffee spout, and lift the milk spout over it as shown in the following illustration.

A. Lighter froth B. Milk frother pointer

C. Thicker froth

6. Remove the hot water spout and attach the milk container to

the hot water and steam nozzle.

A. Hot water and steam nozzle B. Hot water spout

A. Milk spout B. Coffee spouts C. Cup

8. Press CAPPUCCINO. “CAPPUCCINO” will be displayed. After a few seconds, frothed milk will run out of the milk spout and fill the cup below. After the milk runoff stops, coffee runoff will begin automatically.

NOTE: Press CAPPUCCINO at any time to stop the cappuccino process.

9. When the coffee runoff stops, the cappuccino is ready. Add sugar and powdered cocoa to taste.

If the coffee system runs out of milk during the milk runoff, release the milk container and add more milk. Reattach the milk container and press CAPPUCCINO to prepare more cappuccino.

After making cappuccino, always clean the internal tubes of the milk container lid and the hot water and steam nozzle.

+ 25 hidden pages

Jenn-Air JBC7624BS0 Owner’s Manual

TABLE OF CONTENTS

COFFEE SYSTEM SAFETY

TABLE DES MATIÈRES

PARTS AND FEATURES

BEFORE USING THE COFFEE SYSTEM

COFFEE SYSTEM USE

Settings

Switching On and Preheating

Changing the Amount of Coffee

Adjusting the Coffee Grinder

Making Cappuccino