Jenn-Air JBBFX24NHX User Manual
PRODUCT MODEL NUMBERS
1
/16"
(2 mm)
3
/8"
(9 mm)
1
/8"
(4 mm)
Bottom Mount Built-In Refrigerator
PRODUCT DIMENSIONS
JBBFX24NHX
Electrical: A 115 volt, 60 Hz., AC-only, 15 or 20 amp fused, grounded electrical
supply is required. It is recommended that a separate circuit serving only your
refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do
not use an extension cord.
IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit
Interrupter) protected outlet, nuisance tripping of the power supply may occur,
resulting in loss of cooling. Food quality and flavor may be affected. If nuisance
tripping has occurred, and if the condition of the food appears poor, dispose of it.
NOTE: Before performing any type of installation or cleaning, disconnect power
at the circuit breaker box.
When you are finished, reconnect power at the circuit breaker box. Then reset the
control to the desired setting.
LOCATION REQUIREMENTS
n It is recommended that you do not install the refrigerator near an oven,
radiator, or other heat source.
n Do not install in a location where the temperature will fall below 55°F (13°C).
n Floor must support the refrigerator weight of more than 600 lbs (272 kg),
including door panels and contents of the refrigerator.
OPENING DIMENSIONS
n The unit is 69¹¹⁄₁₆" (1770 mm) high, 21¼" (540 mm) wide, and
21½" (546 mm) deep (front to back).
n The refrigerator door (including hinges [x2]) is 42" (1067 mm) high.
The freezer door (including hinges [x2]) is 26¼" (667 mm) high.
The space between the refrigerator and freezer doors is 2³⁄₈" (60 mm).
The space between the door hinges is ¹³⁄₃₂" (10 mm).
n A grounded 3 prong electrical outlet should be placed within 4" (102 mm)
of the right side cabinets or end panel. See the “Electrical Requirements”
section of the Installation Instructions for additional information.
If the space between the top of the frame and the ceiling is enclosed as part
of the surrounding cabinetry, a vent with an opening of at least 31 sq. in.
(200 sq. cm) is required. The bottom of the vent must be a minimum of 7⁷⁄₈"
(200 mm) above the refrigerator.
NOTE: Vent covers are not supplied with the unit.
This refrigerator is designed to be installed inside a frame that fits between kitchen
cabinets. The inside of the frame should be a minimum of 70" (1778 mm) high,
22" (559 mm) wide, and 21⁷⁄₈" (555 mm) deep (front to back).
For proper ventilation, you must allow adequate unobstructed space behind the
refrigerator and below and above the frame. Air enters below the refrigerator and
exits above it.
n Allow a clearance minimum of 2" (51 mm) at the top of the frame.
n The minimum depth of the base of the frame is 20¹⁄₂" (520 mm) (front to back).
n The base can be as desired, but height should match height of the toe kick of
surrounding cabinets. A vent with an opening of at least 31 sq in. (200 sq. cm)
is required for proper ventilation.
n If the space between the top of the frame and the ceiling is open air, allow a
minimum of 7⁷⁄₈" (200 mm) above the refrigerator.
7
/8"
7
(200 mm)
(200 mm)
(200 mm)
(200 mm2)
(200 mm2)
31"
31"
(200 mm2)
(200 mm2)
7
7
/8"
77/8"
(200 mm)
(200 mm)
2
2
2
2
1"
31"
3
(200 mm2)
(200 mm2)
77/8"
77/8"
3
31"
E
B
H
J
G
A
C
K
L
D
I
F
M
N
O
Dimension Table
A 70" (1778 mm) I
B 22" (559 cm) J
C
D
2
2
1"
E minimum 2" min. (51 mm) M 28" (711 mm)
F
G 21¼" (540 mm) O
H 21½" (546 mm)
minimum 21⁷⁄₈" (555 mm)
minimum 20½" (520 mm)
69¹¹/₁₆"(1770 mm)
K 42" (1067 mm)
L
N 26¼ (667 mm)
³⁄₈" (60 mm)
2
¹⁄₁₆" (2 mm)
13
⁄32" (10 mm)
1¹/₈ (29 mm)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with the product. Specifications subject to change without notice.
Ref. W11175294A
10/17
Loading...