Jenn-Air JB36SSFXLA01, JB36SSFXLA02, JB36SSFXRA01, JB36SSFXRA02, JF42SSFXDA01 Installation Guide

...

JENN-AIR_BOTTOMMOUNTBUILT-INREFRIGERATOR

CONGELADORENLAPARTEINFERIORDEJENN-AII_

RI_FRIGI_RATEURENCASTRI_AVECCONGI_LA'IEUR

ENBASJENN-AII_

INSTALLATIONGUIDE

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

MANUAL DEINSTALACION

Si tiene preguntas respecto a las caracteristicas, funcionamiento, rendimiento, partes, accesorios o servicio tecnico, Ilame al:

1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En CanadA, Ilame al: 1-800-807-6777, o visite nuestro sitio de internet: www.jennair.ca.

GUIDED'INSTALLATION

Au Canada, pour des questions a propos des caracteristiques, du fonctionnement/rendement, des pieces, accessoires ou

service, composez le, composez le 1-800-807-6777 ou visitez notre site web & www.jennair.ca.

Table of Contents/[ndice/Table des matieres ...................................................................................... 2

JENN-AIR°

W10555566A

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

36" MODELS ................................................................................... 4

42" FRENCH DOOR MODELS ...................................................... 5

INSTALLATION REQUIREMENTS ................................................ 6

Tools and Parts ............................................................................ 6

Location Requirements ................................................................ 6

Electrical Requirements ............................................................... 7

Water Supply Requirements ........................................................ 8

Tipping Radius ............................................................................. 8

Product Dimensions ..................................................................... 9

Door Swing Dimensions ............................................................. 10

Overlay Series Door Panel and Cabinetry Clearance

(36" [91.4 cm] Models) ............................................................... 11

Overlay Series Door Panel and Cabinetry Clearance

(42" [106.7 cm] Models) ............................................................. 13

Overlay Series Custom Panels .................................................. 15

Custom Overlay Panel Dimensions ........................................... 15

Euro-Style and Pro-Style ®Door Handle Kits ............................. 17

/NDICE

Euro-Style and Pro-Style ®Custom Side Panels ........................ 17

Overlay Series Custom Side Panels .......................................... 18

INSTALLATION INSTRUCTIONS ................................................ 19

Unpack the Refrigerator ............................................................. 19

Reduce Tipping Radius .............................................................. 19

Move the Refrigerator into House .............................................. 20

Install Anti-Tip Boards ................................................................ 20

Connect the Water Supply ......................................................... 21

Plug in Refrigerator ..................................................................... 22

Move Refrigerator to Final Location ........................................... 22

Level and Align Refrigerator ....................................................... 22

Install Overlay Series Custom Panels ........................................ 23

Adjust Door(s) ............................................................................. 24

Install Side Panel ........................................................................ 26

Install Base Grille ........................................................................ 27

Complete Installation .................................................................. 27

Water System Preparation ......................................................... 27

SEGURIDAD DEL REFRIGERADOR ........................................... 28

MODELOS DE 36". ....................................................................... 29

MODELOS DE DOS PUERTAS CON CONGELADOR

EN LA PARTE INFERIOR, DE 42". .............................................. 30

REQUlSITOS DE INSTALACION ................................................. 31

Herramientas y piezas ................................................................ 31

Requisitos de ubicaci6n ............................................................. 31

Requisitos electricos .................................................................. 32

Requisitos del suministro de agua............................................. 33

Arco de vuelco ........................................................................... 33

Medidas del producto ................................................................ 34

Medidas de oscilaci6n de la puerta ........................................... 35

Espacio para el panel de la puerta de la serie de paneles

recubiertos y para los armarios (modelos de 36" [91,4 cm]).....36

Espacio para el panel de la puerta de la serie de paneles recubiertos y para los armarios

(modelos de 42" [106,7 cm]) ...................................................... 38

Paneles a la medida de la serie de paneles recubiertos ........... 40

Dimensiones del panel recubierto a la medida ......................... 40

Juegos de manijas para puertas

de estilo europeo y Pro-Style ®................................................... 42

TABLEDESMATIERES

SI_CURITI_ DU RI_FRIGI_RATEUR .............................................. 54

MODELES DE 36". ....................................................................... 55

MODELES AVEC PORTES .&,DOUBLE BATTANT DE 42". ...... 56

EXIGENCES D'INSTALLATION ................................................... 57

Outillage et pieces ...................................................................... 57

Exigences d'emplacement ......................................................... 57

Specifications electriques .......................................................... 58

Specifications de I'alimentation en eau ..................................... 59

Rayon de basculement .............................................................. 59

Dimensions du produit ............................................................... 60

Dimensions pour le pivotement des portes ............................... 61

Serie Panneaux decoratifs--Panneau de porte et placard--

dimensions et espace libre (modeles de 36" [91,4 cm])............ 62

Serie Panneaux decoratifs--Panneau de porte et placard--

dimensions et espace libre (modeles de 42" [106,7 cm]) .......... 64

Panneaux personnalises de la serie Panneaux decoratifs ........66

Panneaux personnalises-- Dimensions ..................................... 66

Ensembles de poignees de porte Euro-Style et Pro-Style ®...... 68

Panneaux lateraux personnalises

Euro-Style et Pro-Style ®.............................................................. 68

Paneles laterales a la medida para las series

Euro-Style y Pro-Style ®.............................................................. 42

Paneles laterales a la medida para la

serie de paneles recubiertos ...................................................... 43

INSTRUCCIONES DE INSTALACION ......................................... 44

Desempaque el refrigerador ...................................................... 44

C6mo reducir el arco de vuelco ................................................. 45

C6mo hacer entrar el refrigerador en la casa ............................ 45

C6mo instalarlos tableros antivuelco ........................................ 45

Conexi6n del suministro de agua .............................................. 46

C6mo enchufar el refrigerador ................................................... 47

C6mo mover el refrigerador a su ubicaci6n final ....................... 47

Nivelaci6n y alineamiento del refrigerador ................................. 48

Como instalarlos paneles a la medida

para la Serie Overlay .................................................................. 48

Como ajustar la(s) puerta(s) ....................................................... 50

Como instalar el panel lateral ..................................................... 52

Como instalar la rejilla de la base .............................................. 52

Como terminar la instalacion ..................................................... 53

Preparacion del sistema de agua .............................................. 53

Panneaux lateraux personnalises de la

serie Panneaux decoratifs .......................................................... 69

INSTRUCTIONS D'INSTALLATION ............................................. 70

Deballage du refrig6rateur .......................................................... 70

Reduction du rayon de basculement ......................................... 71

Faire entrer le refrig6rateur dans le domicile ............................. 71

Installation de planches antibasculement .................................. 71

Raccordement & la canalisation d'eau ....................................... 72

Branchement du r6frigerateur .................................................... 73

Deplacement du refrig6rateur & I'emplacement final................. 73

Reglage de I'aplomb et alignement du refrig6rateur ................. 74

Installation des panneaux personnalises

de la serie Panneaux decoratifs ................................................. 74

Ajustement de la (des) porte(s)................................................... 76

Installation du panneau lateral ................................................... 78

Installation de la grille de la base ............................................... 78

Achever I'installation .................................................................. 79

Preparation du systeme d'eau ................................................... 79

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

36"MODELS

Euro-Style Design Features stainless steel wrapped doors with towel bar handles.

JB36SEFXRB JB36SEFXLB

Pro-Style ®Design Features stainless steel wrapped doors and heavy duty handles

with diamond-etched grip. JB36PPFXRB JB36PPFXLB

Oiled Bronze Design Features warm bronze and copper highlights that are accented

by sleek, stainless steel handles. JB36REFXRB JB36REFXLB

Overlay Design Uses custom-made panels and custom hardware for a seamless

appearance designed to blend with existing kitchen cabinetry. JB36CXFXRB JB36CXFXLB

42" FRENCHDOOR MODELS

Euro-Style Design Features stainless steel wrapped doors with towel bar handles.

JF42SEFXDB

Pro-Style ®Design Features stainless steel wrapped doors and heavy duty handles

with diamond-etched grip. JF42PPFXDB

Oiled Bronze Design Features warm bronze and copper highlights that are accented

by sleek, stainless steel handles. JF42REFXDB

Overlay Design Uses custom-made panels and custom hardware for a seamless

appearance designed to blend with existing kitchen cabinetry. JF42CXFXDB

INSTALLATIONREQUIREMENTS

IMPORTANT:

• Installer: Leave Installation Instructions with the homeowner.

• Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local

electrical inspector's use.

Tools Needed Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

• Cordless drill • Torx®tT15 and T27 Screwdrivers

• Drill bits • 1V32"nut driver

• Adjustable • 3/8",V4",and V2"open-end wrenches (2) wrenches

• Phillips screwdriver • %2" hex key

• Small level • V4" and %d' socket drivers

• Appliance dolly • Tape measure

• Utility knife

Parts Needed

• #8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6)

• 2" x 4" x 32" (5 cm x 10cm x 81 cm) wood board(s) (1 or 2)

• Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See "Installation Requirements" for more information.

Pro-Style ®and Euro-Style are shipped complete.

• If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need aferrule, a union, and a V4"compression fitting.

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IM PORTANT:

• Observe all governing codes and ordinances.

• It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall below 55°F (13°C).

• Floor must support the refrigerator weight, more than 600 Ibs (272 kg), door panels and contents of the refrigerator.

• Ceiling height must allow for side tipping radius. See "Tipping Radius."

• Location should permit door to open fully. See "Door Swing Dimensions."

• Location must permit top grille removal. See "Opening Dimensions."

I"®TORX is a registered trademark of Saturn Fasteners, Inc.

Opening Dimensions

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. Ifthe solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 to 229 cm) above the floor. See "Install Anti-Tip Boards" for more information.

NOTE: A clearance of V2"(1.3 cm) must be maintained in front of the refrigerator's side trim in order for the top grille to be

removed.

Agrounded3prongelectricaloutletshouldbeplacedwithin 4"(10.2cm)oftherightsidecabinetsorendpanel.See "ElectricalRequirements"foradditionalinformation.

Thewatershutoffshouldbelocatedinthebasecabineton eithersideoftherefrigeratororsomeothereasilyaccessible

area.Ifthewatershutoffvalveisnotinthecabinets,the plumbingforthewaterlinecancomethroughthefloororthe backwall.See"WaterSupplyRequirements"formore specificinformation.

831/2" (212.1 cm) min. 843/4" (215 cm) max.

to bottom of solid soffit

ii 80"-g0" ii

==ii(203"229 cm)i i=

(see chart following)

Width

Electrical Shock Hazard

Dimension

77"

(196 cm)

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker

box. When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control to the desired setting.

24"

(60.96 cm) min.

Width A Width A for Dimension B

(as shown Overlay Models (as shown

Model above) (as shown above) above)

36 351/2"to 353/4'' 353/4"to 36" 4" (10.2 cm)

(90.2 cm to (90.8 cm to 91.4 cm)

90.8 cm)

42 411/2"to 413/4'' 413/4"to 42" 10" (25.4 cm)

(105.4 cm to (106 cm to 106.7 cm) 106 cm)

NOTE: Flooring under refrigerator must be at same level as the room.

(15.2 c

Water Pressure

Allinstallationsmustmeetlocalplumbingcoderequirements. Thewatershutoffshouldbelocatedinthebasecabineton

eithersideoftherefrigeratororsomeothereasilyaccessible area.Theright-handsideisrecommended.Theaccesshole throughthecabinetmustbewithin1/2"(12.7mm)oftherear

wall. NOTE:Ifthewatershutoffvalveisinthebackwallbehindthe

refrigerator,itmustbeatananglesothatthetubeisnot kinkedwhentherefrigeratorispushedintoitsfinallocation.

(15.2 cm)

24"

(60.96 cm) min.

• If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor. A 1/2"(12.7 mm) hole for plumbing should be drilled at least 6" (15.2 cm) from the right or left hand side cabinet or panel. On the floor, the hole should be no more than 1" (2.54 cm) away from the back wall. See "Connect the Water Supply."

• If additional tubing is needed, use copper tubing and check for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

• Do not use a piercing-type or %e" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

Rc_dt s

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

• The dolly wheel height must be added to the tipping radius when a dolly is used.

• If needed, the tipping radius can be reduced. See "Reduce Tipping Radius."

Side Tipping Radius (36" [91.4 cm] Models)

(

,_-_ (229.9 cm)

90W'

A. Tip this side only.

ii ii

Side Tipping Radius (42" [106.7 cm] Models)

/Jff J

_-_ (236.2 cm)

93"

A. Tip this side only.

TopView

36" (91.4 cm) Models

351/4"

(89.5 cm)

253/8" (64.5 cm)

NOTE: Add up to 2_V_e'' (6.74 cm) for the handles. 42" (106.7 cm) Models

411/4" _ I

(105 cm) _ I

Side View

The power cord is 84" (213 cm) long. The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long. Height dimensions are shown with leveling legs extended V8" (3 mm) below the rollers.

A _--

231/2''

(59.7 cm)

"833/8"

(211.8 cm)

84" (213.4 cm)

Power Cord

253/8" (64.5 cm)

NOTE: Add up to 2_V_e'' (6.74 cm) for the handles.

Front View

• Width dimensions were measured from trim edge to trim edge.

• Height dimensions are shown with leveling legs extended Vs"

(3 mm) below the rollers.

36" (91.4 cm) Models

"31/2" (8.9 cm)

Series A

Overlay Design 25V8" (63.8 cm) Euro-Style or Pro-Style ®Design 253/8'' (64.5 cm)

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8"(2.9 cm) to the height dimensions.

.833/8 ,, (211.8 cm)

llliilHllHHHHlilllliiilllllllli 1

-9[-1 361/4'' (92 cm)

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8" (2.9 cm) to the height dimensions.

42" (106.7 cm) Models

The location must permit the door to open to a minimum of 90°. Allow 41/2"(11.4 cm) minimum space between the side of the refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay panels or custom handles.

To adjust the door swing, see "Adjust Door Swing."

36" (91.4 cm) Models

23"

_-_ (58 cm)

max.

59"

(150 cm)

...._.................!!!!!!!!!!!!!!!!!!W _. I,IHlll,

_-_ 421/4'' (107.3 cm)_

*When leveling legs are fully extended to 1V4"(3.2 cm) below

rollers, add 1V8"(2.9 cm) to the height dimensions.

42" (106.7 cm) Models

///:' ii ._J \\_ ii ',', .\

// ,,',,' i', 90_.xx \ \ "90° ,,: ',,', \\

,'?,'_ _Jd 130° 130°4d,--_', ,',

(102.7 cm)

131/2''

(34 _cm)

r ax.

407A6''

441/4'' (112.3 cm)

,4 _ _ _ "_'_ _' _"_ .... " _....... C __S A

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If the refrigerator is to be installed close to the wall, see "Door Swing 90°,' on next page.

_56 cm) M_"_ <_:s

Door Swing 110 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator Side Trim

NOTE: For Overlay Series models, rout the

hinge side of the custom door panels to a radius that is equal to at least half the

thickness of the panel if a 130° door swing is desired. See "Adjust Doors."

Hinge

3/411

(1.9cm)

cm)', ',

11/4" "

(3.2 cm)',

11/2" (3.8cm)

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

Panel

90° Door

Stop Position

Refrigerator Side Trim

(1.9 cm)

/2 ',

(1.3,cm)i

,, ,,

i i i i

Cabin,'etr_/

Door Swing 90°

Actual Size

Refrigerator to Cabinetry Clearance

(2.5 cm)

3/4"

Hinge

1/2"

(1.30m)

(1.90m) i

"--II m

,,<

1/4"(6.35 mm)

1/2"(1.3 cm)

3/4"(1.9 cm)

1" (2.5 cm)

3/4"

I 1"

(2.5cm)

11/4"

(3.2 cm)

11/2"

(3.8cm)

jj'_

Spacer Panel

Allow a minimum of 41/2"(11.4 cm) of space between the side of the refrigerator and a corner wall. More clearance may be needed if thicker custom panels or custom handles are used. Do not overlook baseboards.

Thecustomdoorpanelsandadjacentcabinetrymustbedesignedsothatthereissufficientclearanceforthedoorstoswingopen.If therefrigeratoristobeinstalledclosetothewall,see"DoorSwing90°''onnextpage.

Door Swing 110 °

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator Side Trim

[

Hinge

NOTE: For Overlay Series models, rout the hinge side of the custom door panels to a radius that is equal to at least half the

thickness of the panel if a 130° door swing is desired. See "Adjust Doors."

3/411

(1.9cm)

NOTE: Allow W' (1.3 cm) clearance

between overlay panel and cabinetry.

11 \

(2.5 cm)', ',

11/4" ',

(3.2 cm)',

Panel

11/_,, (3.8cm)

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

90° Door

Stop Position

O Hinge

Refrigerator Side Trim

[

3/4"

(1.9 cm)

1 II I

/2 ,,

(1.3 cm),,

i '

i i

,, ,,

Cabin_etr_

Door Swing 90 °

Actual Size

Refrigerator to

Cabinetry Clearance

(2.5 cm)

1/4" (6.35 mm)

1/2" (1.3 cm)

......... r ......... 3/4" (1.9 cm)

1" (2.5 cm)

1/2"

(1.3 cm)

3/4"

(1.90m) i

I 1"

(2.5ore)

11/4"

O O

"=l

"=l i

(3.2 cm)

11/2"

(3.8cm)

Spacer Panel

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen decor and to use custom handles for additional design flexibility.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a 1/8"(3.18 mm) spacer panel or spacer strips and a 1/4" (6.35 mm) backer panel.

Overlay Panel

(15.88 to 1/8" (6.35 mm)

19.05 ram) (3.18 ram)

Custom Overlay Panels (36" [91.4 cm] Models) Custom Backer Panels (36" [91.4 cm] Models)

Spacer Panel

Backer Panel

Spacer Panel

1/8" @

'ii Ov r,a ane,

-r-J BockorPane,

_1" minimum .

1 (2.54 cm_ ......

I _'D_oor/G rille Trim

I . .

_,_ Offset Dimension

343/4'' > 333/4" >_

(88.27 cm) _ (85.73 cm) Center

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

IM PORTANT:

• For 36" (91.4 cm) models, the refrigerator door overlay panel cannot exceed 50 Ibs (23 kg) and the freezer drawer overlay panel cannot exceed 20 Ibs (9.1 kg).

• For 42" (106.7 cm) models, the refrigerator door overlay panel cannot exceed 30 Ibs (13.5 kg) and the freezer drawer overlay panel cannot exceed 25 Ibs (11.4 kg).

• The weight of the top grille overlay panel cannot exceed 10 Ibs (4.5 kg) for both models.

To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and side edges of the backer panel. If you use spacer strips, it is also recommended that you use two 2" (5.08 cm) strips horizontally centered for added support.

Backer

71/4"T i TOP GRILLE PANEL j 64A6"---_-I[ 4,,,,,, Panel

(18.42cm)____j (15.72 cm)J[_ 1, _t _j left to

MaximumWeight: 10Ibs (4.5 kg) =

343/4"

(88.27 cm)

= right

_ Bottom Offset

%" (9.5 ram)

.................. q

(87.00 cm) r

Center Backer

-------Panel left to

right

Center

', Backer

,.............Panel

' I left to

I right

511/8''

(129.86 cm)

203/4''

(52.71 cm)

REFRIGERATOR DOOR PANEL

MaximumWeight: 50 Ibs (23 kg)

FREEZER DOOR PANEL

Maximum Weight: 20 robs(9.1 kg)

491/8''

(124.78 cm)

== =

I (87.00 cm)

203A6,,

(51.28 cm)

_ Bottom Offset

Yld' (11.1 mm)

341/4''

Bottom Offset

1/4"(6.35 mm)

Custom Overlay Panels (42" [106.7 cm] Models) Custom Backer Panels (42" [106.7 cm] Models)

407A6''

(102.7 cm)

71/4"T i TOP GRILLE PANEL i

(18.4 cm)__l Maximum Weight: 10 robs(4.5 kg)

(50.2-0"m)8c-_ <(-- 20" __.

(50.8 cm)

511/4"

(130.2 cm)

REFRIGERATOR

DOOR PANEL

MaximumWeight:

30 Ibs (13.5 kg)

REFRIGERATOR

DOOR PANEL

Maximum Weight:

30 robs(13.5 kg)

511/4"

(130.2 cm)

Side

Offset

3/16 II

(4.7 ram)

, ,IT61/ ,,

i -

' _f I1 ____(15.9cm)

_>_ __Side Offset /_Bottom Offset

3/8 (9.5 mm) 1/2"(1.27 cm)

493116'' (124.93 cm)

,K-

(1.27 cm)

(100.6 cm)

Bottom

Offset

1/211

39%"

19%" --_"

(49.85 cm)

493116'' (124.93 cm)

Bottom

Offset

1/211

(1.27 cm)

_i .... _L

! Exterior

Panel

extends above

door.

.<_Side

Offset

3/16 II

(4.7 mm)

4077_6''

(102.7 em)

201/4"

(51.4 cm)

Spacer Panels (All models) NOTE: Spacer panels must be at least 1" (2.54 cm) from the top, bottom, and side edges of the backer panel.

3-Piece Grille Overlay Panel Configuration

TopView Side View

FREEZER DOOR PANEL

Maximum Weight: 25 Ibs (11.4 kg)

3-Piece Door Overlay Panel Configuration

|||== = =l =.

i 19!/| ii

II 8

I (50.48 cm)

| .........

40"

(101.6 cm)

_- Offset all sides

A. Offset dimension

B. ¼" (6.25 mm) Backer panel C. _" (3.18 mm) Spacer panel D. _" (1.92 cm) Decorative overlay

panel

ii i!

.............. S

_,f, S'_ D

A. Offset dimension B. ¼" (6.25 mm) Backer panel

C. _" (3.18 mm) Spacer panel D. _" (1.92 cm) Decorative overlay panel

3/16"(4.7 mm)

C D

..... A

1-Piece Overlay Panel Configuration

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimesions and placement instructions to be sure that the custom overlay panels will fit properly.

Inset Installation Dimensions

All factory parts are available through your Jenn-Air dealer or by calling Jenn-Air at 1-800-JENNAIR (1-800-536-6247). In

Canada, call 1-800-807-6777. Follow the kit instructions for installing the door handles.

Series 36" Models 42" Models

Euro-Style #W10197087 #W10197088 Pro-Style ® #W10197089 #W10197090

M, [_,J_SSy....

s ,+u Sde nes

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed and the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and may not reflect the needed panel installation

dimensions. The side panel should be a minimum of 1/2"(1.27 cm) thick

to avoid warping. If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on the rear wall.

Refrigerator

1. Measure the distance from point A (as shown) to the back wall. Add 7/32"(5.6 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than 1/4"(6.35 mm) thick, rout the front edge to allow the side panel to fit into the trim.

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back wall.

2. Attach the support board with a screw or adhesive that is compatible with aluminum and wood.

241/8"

(61.3 cm)

Side Trim

(60.3 cm)

231/2''

(59.7 cm)

(6.35 mm)

(4.7 mm)

Recessed Inset Installation Dimensions

1. Measurethe distance from point A (asshown) to back wall.

2. Rout the front edge of the support board or attach a 1/4" (6.35 mm) board to hold the panel in the cabinet side trim.

11/64"

(4.5 mm)

3/16"

1%2" (10 mm)

(15.7 mm)

c y esCu m Sde nes

Custom side panels may be needed when not enough space is Side Trim (36" [91.4 cm] Models) available to have cabinets on both sides of the refrigerator or

when the refrigerator is placed and the end of a cabinet run. You may choose an Inset or Recessed Inset panel installation. 3/8,,

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

• The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions.

• The side panel should be aminimum of 1/2"(1.27 cm) thick to avoid warping.

• If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on the rear wall.

Refrigerator (36" [91.4 cm] Models)

Overlay

(9.7 mm)

1/16"

(1.5 mm)

3_2"

(2.36 mm)

3,/16"

(4.5 mm)

(60.16 cm)

Refrigerator (42" [106.7 cm] Models)

(69.40 cm)

2311/16''

Overlay

233/8"

Side Trim (42" [106.7 cm] Models)

3,/8"

(9.7 mm)

(1.5mm)

1_6. L

1/8,,

(3.2 mm)

Inset Installation Dimensions

Recessed Inset Installation Dimensions

36" [91.4 cm] Models

1. Measure the distance from point A (as shown) to the back wall. Add 1/32"(0.8 mm) to this measurement to allow the side panel to fit into the trim.

(

2. If the panel is more than 3/8"(9.5 mm) thick, rout the front edge to allow the side panel to fit into the trim

42" [106.7 cm] Models

1. Measure the distance from point A (as shown) to the back wall. Add 1/32"(0.8 mm) to this measurement to allow the side panel to fit into the trim.

If the panel is more than 3/8"(9.5 mm) thick, rout the front edge to allow the side panel to fit into the trim.

36" [91.4 cm] Models

1. Measurethe distance from point A (asshown) to back wall.

2. Rout the front edge of the support board or attach a 3/8" (9.5 mm) board to hold the panel in the cabinet side trim.

42" [106.7 cm] Models

1. Measure the distance from point A (as shown) to back wall.

A m

2. Rout the front edge of the support board or attach a 3/8" (9.5 mm) board to hold the panel in the cabinet side trim.

INSTALLATIONINSTRUCTIONS

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

• Do not remove the film covering until the refrigerator is in its operating location.

• All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

• Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating location.

1. Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final location.

2. If necessary, reduce the tipping radius. See "Tipping Radius" for ceiling height requirements or "Reduce Tipping Radius" for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to "Move the Refrigerator into

House."

_{S_:_}_4 _' _'s_'_}_"_f" _?#s_ _s

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See "Tipping Radius" in the "Installation Requirements" section for

more information. If you do not have adequate ceiling height to stand the

refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

36 88" (223.5 cm)

42 881/2'' (224.8 cm)

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the 42" (106.7 cm) Models grille on a soft surface.

B A B

))_)iii

A. Top grille B. Cabinet side trim

Remove the 6 screws attaching each cabinet side trim to the refrigerator and remove the side trims.

2. Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5. Do not remove film or cover.

6. Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

Place an appliance dolly under the left side of the refrigerator as shown. Place the corner posts from the packing materials over the trims and handles as appropriate to avoid damage. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles.

36" (91.4 cm) Models

IM PO RTANT:

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

• It is recommended that board(s) be installed before the refrigerator is installed.

• Board(s) must be long enough to fully cover the width of the compressor cover.

• Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

• During installation, raise the refrigerator up so there is 1/4"(6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 11/2"(3.8 cm). The board(s) must overlap the compressor cover.

....... ° °

2" (5 cm)

A. Center board ¼" (6.35 mm) max. above refrigerator B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards C.Attach to studs with six #8 x 3" (7.6 cm) screws D. Compressor cover

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFF.

Style 1 --Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see "Style 2--Copper Line Connection."

1. Unplug refrigerator or disconnect power supply. IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. Remove the short, black plastic tube from the end of the water line inlet. This tube protects the fitting during shipping only.

4. Thread the provided nut onto the shutoff valve as shown.

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

7. Plug in the refrigerator or reconnect power.

8. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Style 2--Copper Line Connection

Connecting to Water Line

NOTE: If existing water line meets the "Water System Requirements," see "Connecting to Refrigerator."

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"to 1Y4" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IM PO RTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a V4"(6.35 mm) hole in the cold water pipe you have selected.

F E D

A. Cold water pipe E. Compression sleeve B. Pipe clamp F. Shutoff valve C. Copper tubing G. Packing nut D. Compression nut

A. Bulb C. Water tubing B. Nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the V4"(6.35 mm) drilled hole inthe water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

8. Turn off the shutoff valve on the water pipe. Coil the copper tubing.

9. Check for leaks around the saddle valve.

Connecting to Refrigerator

1. Unplug the refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. Remove the short, black plastic tube from the end of the water line inlet. This tube keeps the fitting from being damaged during shipping only.

4. Measure the distance from the shutoff valve to the opening in which the refrigerator will be located. Tubing must be extended from the shutoff valve into the refrigerator opening following specific guidelines. See "Water Supply Requirements."

5. A 1/4"x 1/4"(6.35 mm to 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

A B C D E F G

A. Water tubing B. Nut

C. Bulb D. Coupfing (purchased)

E. Ferrule (purchased) F Nut (purchased)

G. Household water fine (as

connected in previous section)

6. Turn shutoff valve ON.

7. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

8. Plug in the refrigerator or reconnect power.

9. Flush the water system. See "Water System Preparation."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before

moving.

1. Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2. Do not remove film or cover.

3. Move the refrigerator straight back and evenly into the opening. Be sure that the refrigerator side trims are not

interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of

the refrigerator.

/%t _ iv ° '_

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All 4 leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1. Use a %6" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be

off the floor.

A. Rear leveling bolt B. Front leveling bolt

Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim.

Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within 1/4"(6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

IM PO RTANI"."

• Install the custom handles prior to installing the panels on the refrigerator. For more information on Jenn-Air custom handle selection, refer to the Jenn-Air Catalog, visit

www.jennair.com, or call 1-800-JENNAIR (1-800-536-6247). In Canada, visit www.jennair.ca, or call

1-800-807-6777.

• Create custom door overlay panels according to the specifications in the "Overlay Series Custom Panels" section.

• Jenn-Air is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panel Installation

1. Remove all tape and door bracing from the refrigerator

door(s) and freezer drawer.

Open the refrigerator door(s) and freezer drawer and remove the trims and corner caps on each door as shown.

A B

/7 ........ C

_/4" (6 mm)

max.

°,

2" (5 cm)

A. Center board _" (6.35 mm) max. above refrigerator B. 2" x 4 " x 32" (5 cm x 10 cm x 81 cm) boards (2) C.Attach to studs with #8 x 3" (7.6 cm) screws (6) D. Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with

the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than

50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1V4"

(3.18 cm) below the rollers.

For Overlay models, additional adjustments may be needed after the custom panels are installed.

A /4;_;/" i"_' A

A. Corner caps B. Refrigerator door trims

C. Freezer drawer trim

Slide the custom panels into the trims on the refrigerator door(s) and freezer drawer, making sure that the backer panel fits into the hinge side trims.

...........................!.............. ..........L .................

A.Panels

Reinstall the trims and corner caps.

Remove the protective skin from the screw covers. Snap the screw covers into the handle trim section.

A. Bottom rail C. End cap B. Nuts D. Top rail

Slide the custom panel into the top grille channel and reattach the end cap.

A. Custom panel

Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

B B

Top Grille Panel

1. Grasp both ends of the top grille.

2. Push straight up; then pull straight out. Place the top grille panel-side down on a soft working surface.

B A B

A. Top grille

B. Cabinet side trims

Remove one end cap by loosening the nuts and sliding the end cap off.

A. Top grille B. Cabinet side trims

Boor Alignment (36" [91.4 cm] Models}

1. Loosen, but do not remove, the four Torx®t27 flat-head mounting screws and the two V4" hex-head mounting screws in the top hinge.

2. Adjust the top hinge of the door to align it.

3. Tighten the Torx®t27 flat-head mounting screws to a torque of approximately 100 inch-pounds (11.3 Nm).

4. Tighten the V4"hex-head screws.

A. Torx ®_27 flat-head mounting screws B. _" hex-head mounting screws

+ 56 hidden pages