Jenn-Air CVEX4100, CVEX4270, CVEX4370 Installation Instruction
r
INSTALLATION
INSTRUCTIONS
ExpressionsConvertible ,_=JENN..AIR
CooktopSenes [ wE600_,_,REET_H,_
Models CVEX4100, CVEX4270 & CVEX4370
IMPORTANT
• InstallationshouldbeperformedbyaJenn-Airauthorizedservicerorotherqualifiedinstaller.
• ReadSafetyPrecautionsintheUse&Caremanualbeforeusingthisappliance.
INSTALLER
• Saveinstallationinstructionsforlocalelectricalinspector'suse.
• Leaveinstallationinstructionswiththeappliance,
CONSUMER
• Retaininstallationinstructionswiththeappliance.
_ay berotatedforhorizontal
orverticaldirectionby loosening
nutsaroundblowerinlet.Accessible
insideventilationchamber.
I
g 20_"-+ 1/16" +_1/16"or + .16 cm
52.23 cm +.16cm A Cul_ut 8"
Cutout 20.30 cm
2Y8"
5.40 cm
_,°
No_s ARE CRITICAL
A B C D E
CUTOUT CUTOUT DUCT DUCT MIN. CABINET
WIDTH DEPTH OPENING OPENING WIDTH
inches cm inches cm inches cm inches cm inches cm
SingleBay 18 11116 47.48 20 9/16 52.23 6 916 16.03 147/16 36.67 21 53.34
DoubleBay 307/16 77.34 209/16 52.23 17 3/4 45.08 147/16 36.67 33 83.82
Triple Bay 41 31/32 160.60 209/16 52.23 173/4 45.08 147/16 36.67 45 114.30
IMPORTAN"
CUTOUT
DIMENSIONS
8101P414-60
(lo-ol-oo)
SINGLE
See side clearance )1 I<----
note below. TT__-'_ 314,
Clearance/ I In _
Required,_ I LI I _ _-_ "t-
171/2" [ I I] 1"-1-3 Grease /
44.460m/I II I I I , Container K SEE NOTE
/ I II I LI I BELOW
J" 12 1i2"-_1 BELOW
31.76 cm
DOUBLE
note below, r
See side clearance )J 1(--i 14J-J#4c
I . m
I
.,n [] --LEp--
Clearance_ 1"
17 1/2" 29.06 cm K SEE NOTE
44.46 cm BELOW
Required .,_11 7/16"--_.- _ L
[.( 12 1/2_--,- BELOW
31.76 cm
,J SEE NOTE
$
TRIPLE
See side clearance ) I _
note below. -- "l" t- '4 3/4"
I L
Min. T
Clearancet
Required K SEE NOTE
44.46 cm J SEE NOTE
171/2_ 29"06cm _ I__ BELOW
I_ 30 1/8" "
BELOW
76.52 cm
12.01 cm J,
Instructions For Installer:
• Save installation instructions for local inspector's use.
• Leave installation instructions with the appliance.
• Refer to "Installer Installation Suggestions" on page 3 before cutting.
• Dimensions shown in both inches and centimeters.
• Consult ducting guide for proper instruction.
• Dimensions "A" & "B" - tolerances +/-1/16" or +/-,16 cm.
• Dimension "J" - provide 2" min, (5.08 cm) cabinet clearance to motor for cooling purpose.
NOTE:Where possible, 6" (15,24 cm) is recommended for motor blower service.
• Dimension "K" - provide 6-1/4" (15.88 cm) required for removal of (supplied) grease container(s).
Installed dimension for (supplied) grease container(s) is 5-1/2" (13.97 cm),
• Side Clearance - grills installed near a side wall must allow a minimum clearance of 6" (15.24 cm) between cooktop
and sidewall for maximum performance. Minimum clearance of 1" (2.54 cm) is required to sidewalls and 314"
(1.905 cm) to rear wall.
• Electrical Hookup - the unit must be properly circuit protected and wired according to local electrical codes. See
electrical wiring information on page 3. Unit power requirements are located on the serial plate.
2
Installing Cabinetry Over Your Electrical Wiring Information
Jenn-Air Grill The neutralofthisunit is groundedto theframe through
the greengrounding wire. If used on new branch-circuit
A = 30" (76.2 cm) minimum clearance between the topof installations (1996 NEC), mobile homes, recreational
the cooking platform andthe bottom ofan vehicles, or inan areawhere local codes prohibit
unprotected wood or metalcabinet, grounding through the neutral conductor, untwist or
A = 24" (60.96 cm) minimum when bottom of wood or
metal cabinet is protected by not less than 1/4" ground inaccordance with local code. Connectthe white
(0.635 cm). FLAME RETARDANT millboardcovered neutralto the service neutral. Connect all wires to the
with no less than no. 28 MSG sheet steel, 0.015" branch circuitwith approved connectors. Use copper or
(0.038 cm) stainless steel, 0.024" (0.061 cm) aluminum wire. If aluminum wire is used, use connectors
aluminum or copper, recognized for joining aluminum to copper.
* To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located Proper Electrical Supply
above the surface units should be avoided. If cabinet You must provide an adequate electrical supply system
storage is to be provided, the risk can be reduced by as required for your cooktop. All wire connections must be
installing a range hood that projects horizontally a in accordance with local codes and properly insulated.
minimum of 5 inchesbeyond the bottom of the cabinets. Check with local utility for governing electrical codes and
DOTTEDLINES F cooktop installations must be followed. A copy of the
[NDICATE
CONSTRUCTION_ by writing to:
RANGEHOOD I_ National Electrical Code, NFPA No. 70, can be obtained
t National Fire Protection Association
* A BatterymarchPark
I
Installer Installation Suggestions Codes of NFPA No. 70) must be provided. Unit must be
1. Chamfer allexposededges ofdecorativelaminateto properlygroundedin accordancewithlocalwiring code,
preventdamagefromchipping. The chartbelowrecommendsthe minimumcircuit
2. Radiuscorners of cutout andfile to insure smooth the circuit. If smaller sizes of wire are used, the unit
edges andprevent corner cracking, efficiency will be reduced and a fire hazard may be
3. Roughedges, inside corners which have not been hookup be accomplished by a competent electrician.
rounded and forced fits can contribute to cracking of
the countertop laminate.
disconnect the green wire and connect the green wire to
ordinances. In the absence of local electrical codes, the
National Electrical Code, NFPA No. 70, governing electric
Quincy, Massachusetts 02269
A three-wire, single phase, A.C. 1201240 volt 60 cycle
electrical system (properly circuit protected to meet local
protector and wiresize if the appliance is the only unit on
created. It is advisablethat the electrical wiring and
4. Countertop must be supported within 3" (7.62cm) of
cutout. RECOMMENDEDMINIMUM
K,W.RATING CIRCUITPROTECTION WIRESIZE
CAUTION o.SERIALPLATE INAMPERS (AWG)
Warrantyis void on Jenn-Airequipment 0- 4.9 20 12
installedotherthan as recommendedby 5.0- 6.9 30 10
manufacturer.Recommendedwallcapsand 7.O- 9.9 40 8
transitions must be utilized for proper lO,0-11.9 50 8
operationandinstallation. 12.0- 14.9 60 6
Loading...