Jenn-Air 8113P754-60 User Manual

JENN-AIR® DUAL-FUEL MODULAR

DOWNDRAFT SLIDE-IN RANGE

PRO-STYLE

USE & CARE

GUIDE

TABLE OF CONTENTS

Important Safety Instructions .....................................1-4

Ducting Information........................................................... 5

Care & Cleaning ..............................................................5-8

Maintenance......................................................................... 9

Troubleshooting ......................................................... 10-11

Surface Cooking......................................................... 12-16

Oven Cooking.............................................................. 17-23

Options .......................................................................... 24-28

Favorites ...............................................................................29

Setup .............................................................................. 30-32

Cartridges & Accessories ..............................................33

Warranty & Service...........................................................35

Guide d’utilisation et d’entretien .................................36

Guía de uso y cuidado ....................................................72

Installer: Please leave this guide with this appliance. Consumer: Please read and keep this guide for future

reference. Keep sales receipt and/or cancelled check as proof of purchase.

Model Number __________________________________ Serial Number __________________________________ Date of Purchase ________________________________ If you have questions, call:

Jenn-Air Customer Assistance 1-800-JENNAIR (1-800-536-6247) 1-800-688-2080 (U.S. TTY for hearing or speech impaired) (Mon.-Fri., 8 am-8 pm Eastern Time) Internet: http://www.jennair.com

In our continuing effort to improve the quality and performance of our cooking products, it may be necessary to make changes to the appliance without revising this guide.

For service information, see page 35.

IMPORTANT SAFETY INSTRUCTIONS

technician. Do not attempt to adjust, repair, service, or replace any part of your appliance unless it is specifically recommended in this guide. All other servicing should be referred to a qualified servicer.

Always disconnect power to appliance before servicing.

WARNING

If the information in this guide is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

– Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this or any appliance.

– IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by

a qualified installer, service agency or the gas supplier.

Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating the appliance.

Always contact the manufacturer about problems or conditions you do not understand.

Recognize Safety Symbols, Words, Labels

WARNING

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION

CAUTION – Hazards or unsafe practices which

COULD result in minor personal injury.

Read and follow all instructions before using this appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a result of improper usage of the appliance. Use appliance only for its intended purpose as described in this guide.

WARNING

Gas leaks may occur in your system and result in a dangerous situation. Gas leaks may not be detected by smell alone. Gas suppliers recommend you purchase and install an UL approved gas detector. Install and use in accordance with the manufacturer’s instructions.

General Instructions

WARNING

• ALL RANGES CAN TIP AND CAUSE INJURIES TO PERSONS

• INSTALL ANTI-TIP DEVICE PACKED WITH RANGE

• FOLLOW ALL INSTALLATION INSTRUCTIONS

WARNING: To reduce risk of tipping of the appliance from abnormal usage or by excessive loading of the oven door, the appliance must be secured by a properly installed anti-tip device.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

To check if device is properly installed, look underneath range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The anti-tip device secures the rear leveling leg to the floor when properly engaged. You should check this anytime the range has been moved.

To Prevent Fire or Smoke Damage

Be sure all packing materials are removed from the appliance before operating it.

Keep area around appliance clear and free from combustible materials. Flammable materials should not be stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away from parts of the appliance that may become warm or hot. Do not leave plastic items on the cooktop as they may melt or soften if left too close to the vent or a lighted surface burner.

Child Safety

CAUTION

NEVER store items of interest to children in cabinets

above an appliance or on backguard of a range. Children climbing on the appliance door to reach items could be seriously injured.

NEVER leave children alone or unsupervised near the appliance when it is in use or is still hot. Children should never be allowed to sit or stand on any part of the appliance as they could be injured or burned.

Children must be taught that the appliance and utensils in it can be hot. Let hot utensils cool in a safe place, out of reach of small children. Children should be taught that an appliance is not a toy. Children should not be allowed to play with controls or other parts of the appliance.

To prevent grease fires, do not let cooking grease or other flammable materials accumulate in or near the appliance.

If appliance is installed near a window, proper precautions should be taken to prevent curtains from blowing over burners.

NEVER leave any items on the cooktop. The hot air from the vent may ignite flammable items and may increase pressure in closed containers which may cause them to burst.

Many aerosol-type spray cans are EXPLOSIVE when exposed to heat and may be highly flammable. Avoid their use or storage near an appliance.

To eliminate the hazard of reaching over hot surface burners, cabinet storage should not be provided directly above a unit. If storage is provided, it should be limited to items which are used infrequently and which are safely stored in an area subjected to heat from an appliance. Temperatures may be unsafe for some items, such as volatile liquids, cleaners or aerosol sprays.

In Case of Fire

Turn off appliance and ventilating hood to avoid spreading the flame. Extinguish flame, then turn on hood to remove smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or cookie sheet.

NEVER pick up or move a flaming pan.

• Oven: Smother fire or flame by closing the oven door.

Do not use water on grease fires. Use baking soda, a dry chemical or foam-type extinguisher to smother fire or flame.

About Your Appliance

WARNING

NEVER use appliance door as a step stool or seat as this

may result in possible tipping of the appliance and serious injuries.

NEVER use this appliance as a space heater to heat or warm a room. Doing so may result in carbon monoxide poisoning and overheating of the oven.

NEVER cover any slots, holes or passages in the oven bottom or cover the entire rack with materials such as aluminum foil. Doing so blocks air flow through the oven and may cause carbon monoxide poisoning. Aluminum foil may also trap heat, causing a fire hazard.

NEVER obstruct the flow of combustion and ventilation air by blocking the oven vent or air intakes. Doing so restricts air to the burners and may result in carbon monoxide poisoning.

Avoid touching oven vent area while oven is on and for several minutes after oven is turned off. Some parts of the vent and surrounding area become hot enough to cause burns. After oven is turned off, do not touch the oven vent or surrounding areas until they have had sufficient time to cool.

Other potentially hot surfaces include cooktop, areas facing the cooktop, oven vent, surface near the vent opening, oven door, area around the oven door and oven window.

Cont.

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect power to the appliance before removing bulb to avoid electrical shock.

To prevent potential hazard to the user and damage to the appliance, do not use appliance as a space heater to heat or warm a room. Also, do not use the oven as a storage area for food or cooking utensils.

NEVER use aluminum foil to cover an oven rack or oven bottom. Misuse could result in risk of electric shock, fire, or damage to the appliance. Use foil only as directed in this guide.

Cooking Safety

Always place a pan on a surface burner before turning it on. Be sure you know which knob controls which surface burner. Make sure the correct burner is turned on and that the burner has ignited. When cooking is completed, turn burner off before removing pan to prevent exposure to burner flame.

Always adjust surface burner flame so that it does not extend beyond the bottom edge of the pan. An excessive flame is hazardous, wastes energy and may damage the appliance, pan or cabinets above the appliance.

NEVER leave a surface cooking operation unattended, especially when using a high heat setting or when deep fat frying. Boilovers cause smoking and greasy spillovers may ignite. Clean up greasy spills as soon as possible.

Do not use high heat for extended cooking operations. NEVER heat an unopened container on the surface

burner or in the oven. Pressure build-up may cause container to burst resulting in serious personal injury or damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause burns from steam. Dish towels or other substitutes should never be used as potholders because they can trail across hot surface burners and ignite or get caught on appliance parts.

Always let quantities of hot fat used for deep fat frying cool before attempting to move or handle.

Do not let cooking grease or other flammable materials accumulate in or near the appliance, hood or vent fan. Clean hood frequently to prevent grease from accumulating on hood or filter. When flaming foods under the hood, turn the fan on.

NEVER wear garments made of flammable material or loose fitting or long-sleeved apparel while cooking. Clothing may ignite or catch utensil handles.

Always place oven racks in the desired positions while oven is cool. Slide oven rack out to add or remove food, using dry, sturdy potholders. Always avoid reaching into the oven to add or remove food. If a rack must be moved while hot, use a dry potholder. Always turn the oven off at the end of cooking.

Use care when opening the oven door. Let hot air or steam escape before moving or replacing food.

PREPARED FOOD WARNING: Follow food manufacturer’s instructions. If a plastic frozen food container and/or its cover distorts, warps, or is otherwise damaged during cooking, immediately discard the food and its container. The food could be contaminated.

NEVER use aluminum foil to cover oven racks or oven bottom. This could result in risk of electric shock, fire, or damage to the appliance. Use foil only as directed in this guide.

Utensil Safety

Use pans with flat bottoms and handles that are easily grasped and stay cool. Avoid using unstable, warped, easily tipped or loose-handled pans. Also avoid using pans, especially small pans, with heavy handles as they could be unstable and easily tip. Pans that are heavy to move when filled with food may also be hazardous.

Be sure utensil is large enough to properly contain food and avoid boilovers. Pan size is particularly important in deep fat frying. Be sure pan will accommodate the volume of food that is to be added as well as the bubble action of fat.

To minimize burns, ignition of flammable materials and spillage due to unintentional contact with the utensil, do not extend handles over adjacent surface burners. Always turn pan handles toward the side or back of the appliance, not out into the room where they are easily hit or reached by small children.

Never let a pan boil dry as this could damage the utensil and the appliance.

Follow the manufacturer’s directions when using oven cooking bags.

Only certain types of glass, glass/ceramic, ceramic or glazed utensils are suitable for cooktop or oven usage without breaking due to the sudden change in temperature. Follow manufacturer’s instructions when using glass.

This appliance has been tested for safe performance using conventional cookware. Do not use any devices or accessories that are not specifically recommended in

this guide. Do not use element covers for the surface units, stovetop grills, or add-on oven convection systems. The use of devices or accessories that are not expressly recommended in this guide can create serious safety hazards, result in performance problems, and reduce the life of the components of the appliance.

Do not clean door gasket. The door gasket is essential for a good seal. Care should be taken not to rub, damage, or move the gasket.

Do not use oven cleaners or oven liners of any kind in or around any part of the self-clean oven.

Deep Fat Fryers

Use extreme caution when moving the grease pan or disposing of hot grease. Allow grease to cool before attempting to move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease or other flammable materials from accumulating on hood or filter and to avoid grease fires.

When flaming foods under the hood, turn the fan on.

Cleaning Safety

Clean cooktop with caution. Turn off all controls and wait for appliance parts to cool before touching or cleaning. Use care to avoid steam burns if a wet sponge or cloth is used to wipe spills on a hot surface. Some cleaners can produce noxious fumes if applied to a hot surface.

Clean only parts listed in this guide.

Self-Clean Oven

Important Safety Notice and Warning

The California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65) requires the Governor of California to publish a list of substances known to the State of California to cause cancer or reproductive harm, and requires businesses to warn customers of potential exposures to such substances.

Users of this appliance are hereby warned that when the oven is engaged in the self-clean cycle, there may be some low-level exposure to some of the listed substances, including carbon monoxide. Exposure to these substances can be minimized by properly venting the oven to the outdoors by opening the windows and/ or door in the room where the appliance is located during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS: Never keep pet birds in the kitchen or in rooms where

the fumes from the kitchen could reach. Birds have a very sensitive respiratory system. Fumes released during an oven self-cleaning cycle may be harmful or fatal to birds. Fumes released due to overheated cooking oil, fat, margarine and overheated non-stick cookware may be equally harmful.

CAUTION

Before self-cleaning the oven, remove the oven racks, broiler pan, food and any other utensils. Wipe spillovers to prevent excessive smoke and flare-ups.

Save These Instructions for Future Reference

DUCTING INFORMATION

Jenn-Air’s ventilation system is designed to capture both cooking fumes and smoke from the cooktop surface. If the system does not, here are some ducting installation situations to check:

• 6” diameter round or 3 should be used for duct lengths 10’-60’.

Important: 5” diameter round ducting may be used if the duct length is 10’ or less.

• No more than three 90° elbows should be used. Distance between elbows should be at least 18”.

• Recommended Jenn-Air wall cap MUST be used. Make sure damper moves freely when ventilation system is operating.

/4” x 10” rectangular ducting

• There should be a minimum clearance of 6” for cooktop installed near a side wall.

If there is not an obvious improper installation, there may be a concealed problem such as a pinched joint, obstruction in the pipe, etc. Installation is the responsibility of the installer and questions should be addressed first by the installer. The installer should very carefully check the ducting installation instructions.

• Use the Flow Tester Card provided with your appliance to check the air flow.

CARE & CLEANING

Self-Clean Oven

CAUTION

• It is normal for parts of the oven to become hot during a self-clean cycle.

• To prevent damage to oven door, do not attempt to open the door when LOCK is displayed.

• Avoid touching door, window or oven vent area during a clean cycle.

• Do not use commercial oven cleaners on the oven finish or around any part of the oven. They will damage the finish or parts.

The self-clean cycle uses above-normal cooking temperatures to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers to prevent excessive smoke and flare-ups. Do not allow a heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

1. Turn off the oven light before cleaning. The oven light may burn out during the clean cycle.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

2. Remove broiler pan, all pans, and oven racks from the oven. The oven racks will discolor and may not slide easily after a self-clean cycle if they are not removed. Important: Remove the air grille from the cooking surface before selfcleaning.

3. Clean oven frame, door frame, area outside of gasket, and around the opening in the door gasket with a nonabrasive cleaner such as Bon Ami* or detergent and water. The self-cleaning process does not clean these areas. They should be cleaned to prevent soil from baking on during the clean cycle. (The gasket is the seal around the oven door and window.)

4. To prevent damage, do not clean or rub the gasket around the oven door. The gasket is designed to seal in heat during the clean cycle.

5. Wipe up excess grease or spill-overs from the oven bottom. This prevents excessive smoking, flare-ups or flaming during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet potatoes, tomato, or milk-based sauces. Porcelain enamel is acid-resistant, not acid-proof. The porcelain finish may discolor if acidic or sugary spills are not wiped up before a self-clean cycle.

To set Self-Clean:

1. Press Clean pad.

2. REMOVE RACKS will be displayed. Remove the racks.

3. Select CONTINUE using the Quickset pad. The Quickset pads are located on either side of the control panel dsplay.

4. Set LIGHT soil level by entering 200 using the number pads for two hours of cleaning time. Press the Enter pad.

Select MEDIUM for a moderately soiled oven and three hours of cleaning time.

Select HEAVY for a heavily soiled oven and four hours of cleaning time.

5. CLEAN, TIME, LOCKED and the cleaning time countdown will be displayed while the oven is cleaning. OVEN COOLING will appear in the display when the cleaning time has been completed and the oven is still locked.

Important: The door lock will disengage approximately one hour after the cleaning time is completed. OVEN COOLING will go off in the display when the oven door has unlocked.

To Delay a Self-Clean Cycle:

1. Press Clean pad.

2. REMOVE RACKS will be displayed. Remove the racks.

3. Select CONTINUE using the Quickset pad.

4. Set LIGHT soil level by entering 200 using the number pads for two hours of cleaning time. Press the Enter pad.

Select MEDIUM for a moderately soiled oven and three hours of cleaning time.

Select HEAVY for a heavily soiled oven and four hours of cleaning time.

5. The door will lock. CLEAN, TIME, LOCKED and the cleaning time countdown will be displayed

6. After door locks, press the More Options pad.

7. Select DELAY using the Quickset pad.

8. Select the number of hours you want to delay the start of the self-clean cycle.

9. The delay time and cleaning time will be displayed.

After Self-Cleaning

About one hour after the end of the clean cycle, the lock will disengage and OVEN COOLING will go off in the display. At this point, the door can be opened.

Some soil may leave a light gray, powdery ash which can be removed with a damp cloth. If soil remains, it indicates that the clean cycle was not long enough. The soil will be removed during the next clean cycle.

If the oven racks were left in the oven and do not slide smoothly after a clean cycle, wipe racks and embossed rack supports with a small amount of vegetable oil to restore ease of movement.

A white discoloration may appear after cleaning if acidic or sugary foods were not wiped up before the clean cycle. This is normal and will NOT affect performance.

Notes:

• If the oven door is left open, CLOSE DOOR will appear in the display until the door is closed.

• If more than 30 seconds elapse between pressing the Clean pad and pressing a number pad, the program will automatically return to the previous display.

• The oven door will be damaged if it is forced to open during cleaning or cooling process.

• The first few times the oven is cleaned, some smoke and odor may be detected. This is normal and will lessen or disappear with use. If the oven is heavily soiled, or if the broiler pan was accidently left in the oven, excessive smoke and odor may occur.

• As the oven heats and cools, you may hear sounds of metal parts expanding and contracting. This is normal and will not damage your appliance.

Cleaning Procedures

CAUTION

• Be sure appliance is off and all parts are cool before handling

or cleaning. This is to avoid damage and possible burns.

• To prevent staining or discoloration, clean appliance after each use.

• If a part is removed, be sure it is correctly replaced.

PART PROCEDURE

Access Panel The access panel is easily removed. To open panel, grasp sides and pull upward, lifting out.

To close panel, align catches with the studs on the range. Press the access panel forward onto the studs and drop downward to engage.

• Wash with soap and water, a glass cleaner, or mild liquid sprays.

• Do not use excessive amounts of water.

• To prevent scratching or dulling of the finish, do not use mildly abrasive, harsh or caustic cleaners such as oven cleaners.

Important: To avoid the possibility of accidentally disconnecting any part of the ventilation system, do not use the area behind the access panel for storage.

Broiler Pan Never cover insert with aluminum foil as this prevents the fat from draining to the pan below. and Insert • Place soapy cloth over insert and pan; let soak to loosen soil.

• Wash in warm, soapy water. Use scouring pad to remove stubborn soil.

• Broiler pan and insert can be cleaned in dishwasher.

* Brand names are registered trademarks of the respective manufacturers. ** To order call 1-800-JENNAIR (1-800-536-6247).

STUDS

CATCHES

GREASE

CUP

Burner Caps Removable Burner Caps and Sealed • Allow burner to cool. Remove burner cap and wash in soapy water with a plastic scouring pad. For Gas Burners stubborn soils, clean with a soap-filled, nonabrasive pad or Cooktop Cleaning Creme*

(Part #20000001)** and a sponge.

• Do not clean in the dishwasher or self-cleaning oven.

Sealed Gas Burners

• Clean frequently. Allow burner to cool. Clean with soap and plastic scouring pad. For stubborn or dried-on soils, clean with a soap-filled, nonabrasive pad, stiff brush, toothbrush, the soft rubber tip on the toothbrush (if equipped) or a straight pin. Do not enlarge or distort holes.

• Be careful not to get water into burner ports.

• Use care when cleaning the ignitor. If the ignitor is wet or damaged the surface burner will not light.

Burner Grates - • Wash with warm, soapy water and a nonabrasive, plastic, scrubbing pad. For stubborn soils, Porcelain on clean with a soap-filled, nonabrasive, plastic pad or Cooktop Cleaning Creme* Cast Iron and a sponge. If soil remains, reapply Cooktop Cleaning Creme*, cover with a damp paper towel and

soak for 30 minutes. Scrub again, rinse and dry.

• Do not clean in the dishwasher or self-cleaning oven.

Cooktop – Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid-resistant, not acid- Porcelain proof. All spillovers, especially acidic or sugary spillovers, should be wiped up immediately with a dry cloth. Enamel • When cool, wash with soapy water, rinse and dry.

• Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

• Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

Clock and • To activate control lock for cleaning, see Locking the Control, page 18. Control Pad • Wipe with damp cloth. Dry thoroughly. Area • Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on control pads and

display area.

• Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel.

Control Knobs • Remove knobs in the OFF position by pulling forward.

• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

• Turn on each element to be sure the knobs have been correctly replaced.

PART PROCEDURE

Grill Parts: Basin and The basin pan and basin are located under the grill element and/or cartridges. Clean after each use of the grill.

Basin Pan – • To remove light soil, clean with soapy water or spray with cleansers such as Fantastik* or Formula 409*. For Porcelain easier cleanup: a) spray with a household cleanser; b) cover with paper towels; c) add small amount of hot

water to keep the paper towels moist; d) cover and wait 15 minutes; and e) wipe clean.

• To remove moderate soil, scrub with Bon Ami*, a soft scrub cleanser or plastic scrubber.

• Basin liner pan can be cleaned in the dishwasher. Important: Check the grease drain after each use of the grill. To clean, pour about 1/3 cup of very hot tap water mixed with 1 teaspoon dish detergent down the drain.

Element • Never immerse in water. Most soil will burn off during use. The terminal block may be wiped with warm

soapy water. Do not use abrasive cleaners or materials. Dry thoroughly before reinserting in the cooktop.

Grates – Cast • Wash cool grates (DO NOT IMMERSE HOT GRILL GRATES IN WATER) with detergent in hot water in the aluminum sink or wash them in the dishwasher. Be sure to remove all food residue before cooking on the grates again. coated with • Remove stubborn soils with a plastic mesh puff or pad. Use only those cleaning products which state they non-stick are recommended for use when cleaning nonstick surfaces. finish • If grates were washed in the dishwasher, season with oil prior to grilling.

• Do not use metal brushes or abrasive scouring pads or other scrubbers intended to clean outdoor charcoal grills. These will remove the finish as well as scratch the grates. Do not clean in self-cleaning oven or use oven cleaners on the grates.

Grease Cup • The container is located on the left side behind the bottom access panel, underneath

the range. (See page 7 for opening access panel.) It collects grease and other liquids created while grilling or using some of the accessories. Check each time after grilling and empty when grease is noticeable. To remove, simply grasp the handle, and pull from the bracket holding the container.

• The container can be washed in hot, soapy water or in the dishwasher.

Oven Window • Avoid using excessive amounts of water which may seep under or behind glass, causing staining. and Door - • Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a cloth. Glass • Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will scratch.

Oven Interior • Follow instructions on pages 5-6 to set a self-clean cycle.

Oven Racks • Clean with warm, soapy water.

• Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

• Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean operation. If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease of movement, then wipe off excess oil.

Side Trim and • When cool, wash with warm, soapy water, rinse and dry. Never wipe a warm or hot surface with a damp Door Handles - cloth as this may damage the surface and may cause a steam burn. Painted • For stubborn soil, use mildly abrasive cleaning agents such as baking soda paste or Bon Ami*. Do not use Enamel abrasive cleaners such as steel wool pads or oven cleaners. These products will scratch or permanently

damage the surface.

Important: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may discolor or dull if soil is not immediately removed. This is especially important for white surfaces.

Stainless Steel • DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH. (select models) • DO NOT USE ABRASIVE OR ORANGE CLEANERS.

• ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

• Daily Cleaning/Light Soil –– Wipe with one of the following - soapy water, white vinegar/water solution, Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.

20000008)**.

• Moderate/Heavy Soil –– Wipe with one of the following - Bon Ami, Smart Cleanser, or Soft Scrub* using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multipurpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks, follow with Stainless Steel Magic Spray*.

• Discoloration –– Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

* Brand names for cleaning products are registered trademarks of the respective manufacturers. ** To order direct, call 1-800-JENNAIR (1-800-536-6247).

MAINTENANCE

Oven Door

CAUTION

NEVER place excessive weight on or stand on an open

oven door. This could cause the range to tip over, break the door, or injure the user.

• NEVER attempt to open or close door or operate oven until door is properly replaced.

• NEVER place fingers between hinge and front oven frame. Hinge arms are spring mounted. If accidentally hit, the hinge will slam shut against oven frame and could injure your fingers.

To remove:

1. When cool, open the oven door

to the broil stop position (opened about four inches).

2. Grasp door at each side. Do not

use the door handle to lift door.

3. Lift up evenly until door clears hinge arms.

To replace:

1. Grasp door at each side.

2. Align slots in the door with the hinge arms on the range.

3. Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top corners of the door to completely seat door on hinges. Door should not appear crooked.

Important: The oven door on a new range may feel “spongy” when it is closed. This is normal and will decrease with use.

Oven Light

4. To avoid damaging or decreasing the life of the new bulb, do not touch the bulb with bare hands or fingers. Hold with a dry cloth or paper towel. Push new bulb prongs straight into small holes of ceramic base.

5. Replace bulb cover by snapping into place.

6. Reconnect power to the oven. Reset clock.

Oven Window

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool scouring pads or powdered cleansers as they may scratch the glass.

2. Do not hit the glass with pots, pans, furniture, toys, or other objects.

3. Do not close the oven door until the oven racks are in place.

Scratching, hitting, jarring or stressing the glass may weaken its structure causing an increased risk of breakage at a later date.

Leveling Legs

CAUTION

Be sure the anti-tip bracket secures one of the rear leveling legs to the floor. This bracket prevents the range from accidentally tipping.

Be sure the range is leveled when installed. If the range is not level, turn the leveling legs, located at each corner of the range, until range is level.

CAUTION

• Disconnect power to oven before replacing light bulb.

• Allow oven to cool before replacing light bulb.

• Make sure bulb cover and bulb are cool before touching.

To assure the proper replacement bulb is used, order bulb from Jenn-Air. Call 1-800-JENNAIR (1-800-536-6247), ask for part number 74004458 - halogen bulb.

To Replace Oven Light Bulb:

1. Disconnect power to the oven.

2. When oven is cool, use fingertips to grasp edge of bulb cover. Pull out and remove.

3. Carefully remove old bulb by pulling straight out of ceramic base.

ANTI-TIP BRACKE

ANTI-TIP BRACKET

LEVELING LEG

Removal of Gas Appliance

Gas appliance connectors used to connect this appliance to the gas supply are not designed for continuous movement. Once installed, DO NOT repeatedly move this gas appliance for cleaning or to relocate. If this appliance has to be moved and/or removed for servicing, follow the procedure described in the installation instructions. For information, contact JennAir Customer Service at 1-800-JENNAIR (1-800-536-6247).

To prevent range from accidentally tipping, range must be secured to the floor by sliding rear leveling leg into the antitip bracket.

TROUBLESHOOTING

PROBLEM SOLUTION

For most concerns, try these first. • Check if oven controls have been properly set.

• Check to be sure plug is securely inserted into receptacle.

• Check or re-set circuit breaker. Check or replace fuse.

• Check power supply.

Part or all of appliance does • Check if surface and/or oven controls have been properly set. See pgs. 12 & 19. not work. • Check if oven door is unlocked after self-clean cycle. See pg. 6.

• Check if oven is set for a delayed cook or clean program. See pgs. 19 & 6.

• Check if Control Lock is activated. See pg. 18.

• Check if control is in Sabbath Mode. See pg. 31.

Clock, indicator words, and/or • Oven may be set for a Cook & Hold or delay function. lights operate but oven does • Control Lock may have been set. See pg. 18. not heat.

Surface burner fails to light. • Check to be sure unit is properly connected to power supply.

• Check for a blown circuit fuse or a tripped main circuit breaker.

• Check to be sure ignitor is dry and clicking. Burner will not light if ignitor is damaged, soiled or wet. If ignitor doesn’t click, turn control knob OFF.

The flame is uneven. • Burner ports may be clogged.

Surface burner flame lifts • Check to be sure a pan is sitting on the grate above. off ports.

Food is not broiling properly or • Check oven rack positions. Food may be too close to flame. smokes excessively. • Aluminum foil was incorrectly used. Never line the broiler insert with foil.

• Trim excess fat from meat before broiling.

• A soiled broiler pan was used.

• Preheat oven for 2-3 minutes before placing food in the oven.

• Broil with the oven door closed.

Baking results are not as • Check the oven temperature selected. Make sure oven is preheated when recipe expected or differ from or directions recommend preheat. previous oven. • Make sure the oven vent has not been blocked. See page 23 for location.

• Check to make sure range is level.

• Temperatures often vary between a new oven and an old one. As ovens age, the oven temperature often “drifts” and may become hotter or cooler. See page 31 for instructions on adjusting the oven temperature. Important: It is not recommended to adjust the temperature if only one or two recipes are in question.

• Use correct pan. Dark pans produce dark browning. Shiny pans produce light browning.

• Check rack positions and pan placement. Stagger pans when using two racks. Allow 1-2 inches between pans and oven wall.

• Check the use of foil in the oven. Never use foil to cover an entire oven rack. Place a small piece of foil on the rack below the pan to catch spillovers.

Cont.

PROBLEM SOLUTION

Oven will not self-clean. • Check to make sure the cycle is not set for a delayed start. See pg. 6.

• Check if door is closed.

• Check if control is in Sabbath Mode. See pg. 31.

• Oven may be over 400° F. Oven temperature must be below 400° F to program a clean cycle.

Oven did not clean properly. • Longer cleaning time may be needed.

• Excessive spillovers, especially sugary and/or acidic foods, were not removed prior to the self-clean cycle.

Oven door will not unlock after • Oven interior is still hot. Allow about one hour for the oven to cool after the self-clean cycle. completion of a self-clean cycle. The door can be opened when the LOCK indicator

word is not displayed.

• The control and door may be locked. See pg. 18.

There are no beeps and • Oven may be in Sabbath Mode. See page 31. no display.

Moisture collects on oven • This is normal when cooking foods high in moisture. window or steam comes from • Excessive moisture was used when cleaning the window. oven vent.

There is a strong odor or light • This is normal for a new range and will disappear after a few uses. Initiating a clean smoke when oven is turned on. cycle will “burn off” the odors more quickly.

• Turning on a ventilation fan will help remove the smoke and/or odor.

• Excessive food soils on the oven bottom. Use a self-clean cycle.

Ventilation system is not • Check on cross ventilation in room or make up air. capturing smoke efficiently. • Outside wall cap may be trapped shut.

• Range may be improperly installed; check ducting information. See pg. 5.

• Air filter may be improperly installed. See pg. 15.

Fault Codes • The oven may detect a fault during programming or during operation. If a fault is

detected, the message FAULT DETECTED - PRESS POWER TO CLEAR or FAULT DETECTED - PRESS ENTER TO TRY AGAIN may appear. Follow directions in the display. If the fault reappears or does not clear, call an authorized servicer or the toll-free number in the display.

• If the same operation is attempted before having the oven repaired, the message FEATURE NOT AVAILABLE will appear. The feature will remain inoperable until service is obtained.

• If the oven is heavily soiled, excessive flareups may result in a fault code during cleaning. Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then reset the clean cycle. If the fault code reappears, contact an authorized servicer.

Noises may be heard. • The oven makes several low-level noises. You may hear the oven relays as they go on

and off. This is normal.

• As the oven heats and cools, you may hear sounds of metal parts expanding and contracting. This is normal and will not damage your appliance.

SAb flashing and then • Oven is in Sabbath Mode. To cancel, press and hold the Setup pad for five displayed continuously. seconds.

Cannot add another Favorite. • Favorites is full. To delete a favorite and add another, see page 29.

SURFACE COOKING

HIGH: Use to bring liquid to a boil, or reach

pressure in a pressure cooker. Always reduce setting to a lower heat when liquids begin to boil or foods begin to cook.

MED: An intermediate flame size is used to continue cooking. Food will not cook any faster when a higher flame setting is used than needed to maintain a gentle boil. Water boils at the same temperature whether boiling gently or vigorously.

Surface Controls

CAUTION

• If flame should go out during a cooking operation and the burner does not reignite itself, turn the burner off. If a strong gas odor is detected, open a window and wait five minutes before relighting the burner.

• Be sure all surface controls are set in the OFF position prior to supplying gas to the range.

• NEVER touch cooktop until it has cooled. Expect some parts of the cooktop, especially around the burners, to become warm or hot during cooking. Use potholders to protect hands.

LOW: Use to simmer foods, keep foods warm and melt chocolate or butter. Some cooking may take place on the Low setting if the pan is covered. It is possible to reduce the heat by rotating the knob toward OFF. Be sure flame is stable.

Setting the controls:

The size and type of cookware will affect the heat setting.

1. Place a pan on the burner grate.

• The burner flame may lift off or appear separated from

the port if a pan is not placed on the grate.

2. Push in and turn the knob counterclockwise to the LIGHT setting.

• A clicking (spark) sound will be heard and the burner

will light. (All of the ignitors will spark whenever any surface burner knob is turned to the LIGHT position.)

3. After the burner lights, turn the knob to the desired flame size.

• The ignitor will continue to spark until the knob is

turned past the LIGHT position.

Pilotless Ignition

Pilotless ignition eliminates the need for a constant standing pilot light. Each surface burner has a spark ignitor. Use care when cleaning around the surface burner.

If the surface burner does not light, check if ignitor is broken, soiled or wet.

Surface Control Knobs

Use to turn on the surface burners. An infinite choice of heat settings is available from LOW to HIGH. The knobs can be set on or between any of the settings.

Graphics next to the knob identify which burner the knob controls. For example, the graphic at left shows the right front burner location.

Operating During a Power Failure

CAUTION

When lighting the surface burners, be sure all of the controls are in the OFF position. Strike the match first and hold it in position before turning the knob to LIGHT.

1. Hold a lighted match to the desired surface burner head.

2. Push in and turn the control knob slowly to LIGHT.

3. Adjust the flame to the desired level.

Cooktop

To prevent the cooktop from discoloring or staining:

• Clean cooktop after each use.

• Wipe acidic or sugary spills as soon as the cooktop has

cooled as these spills may discolor the

porcelain.

Unlike a range with standard gas burners, this cooktop does not lift-up nor is it removable. Do not attempt to lift the

cooktop for any reason.

Sealed Burners

The sealed burners of your range are secured to the cooktop and are not designed to be removed. Since the burners are sealed into the cooktop, boilovers or spills will not seep underneath the cooktop.

However, the burner should be cleaned after each use. The cap portion of the burner is easily removed for cleaning. (See page 7 for cleaning directions.)

The burner caps must be correctly placed on the burner base for proper operation of the burner.

High Performance Burner

There is one 16,000 BTU* high speed burner on your range, located in the right front position. This burner offers higher speed cooking that can be used to quickly bring water to a boil and for large-quantity cooking.

Simmer/Melt Burner

This burner is located in the right rear position. The SIMMER setting can be used to steam or poach foods, to cook delicate sauces or continue cooking covered foods. The ultra low MELT setting is best for melting chocolate and butter.

Burner Grates

The grates must be properly positioned before cooking. When installing the grates, place the tab ends toward the center, matching the straight bars.

Improper installation of the grates may result in chipping of the cooktop.

Do not operate the burners without a pan on the grate. The grate’s porcelain finish may chip without a pan to absorb the heat from the burner flame.

Use care when stirring food in a pot/pan sitting on the burner grate. The grates have a smooth finish for ease of cleaning. The pot/pan will slide if the handle is not held. This may result in spilling of hot food items and may be a burn hazard.

Although the burner grates are durable, they will gradually lose their shine and/or discolor, due to the high temperatures of the gas flame.

Notes:

• A properly adjusted burner with clean ports will light

within a few seconds. If using natural gas, the flame will be blue with a deeper blue inner cone.

If the burner flame is yellow or is noisy, the air/gas mixture may be incorrect. Contact a service technician to adjust. (Adjustments are not covered by the warranty.)

With LP gas, slight yellow tips on the flames are acceptable. This is normal and adjustment is not necessary.

• With some types of gas, you may hear a “popping”

sound when the surface burner is turned off. This is a normal operating sound of the burner.

• If the control knob is turned very quickly from HIGH to

LOW, the flame may go out, particularly if the burner is cold. If this occurs, turn the knob to the OFF position, wait several seconds and relight the burner.

• The flame should be adjusted so it does not extend

beyond the edge of the pan.

Important: When using the normal settings for preparing foods, it may take a few minutes for the cooking area to cool to the MELT heat setting.

* BTU ratings will vary when using LP gas.

Sealed Burner Cartridge Installation

To install Sealed Burner Cartridge:

1. Be sure control knobs are turned OFF.

2. If the grill burner and grill grates are in place, remove before installing a burner cartridge. Clean basin of any grease accumulation. (See page 8 for cleaning recommendations.)

3. Position the burner cartridge with the mixer tube openings and igniter rods toward the orifices and terminal receptacle. Slide the cartridge until the tubes and ignitors engage, then lower the cartridge so that it rests on the range surface.

To remove Sealed Burner Cartridge:

1. Control knobs should be in the OFF position and the range should be cool.

2. Lift up the edge of the cartridge until the bottom of the cartridge clears the basin. (Lifting the cartridge too high while still engaged could damage the ignitor rods and mixer tubes.)

3. To disengage the cartridge, hold by the sides and pull away from the terminal receptacle and orifices. Lift out when fully unplugged.

4. Do not stack cartridges where they may fall or be damaged.

Important: Optional Sealed Burner Cartridge, model JGA9150ADP, can replace the grill burner assembly. To order, call 1-800-JENNAIR (1-800-536-6247).

Grill Installation

The grill assembly consists of two grill grates and a grill burner. Only install the grill on the LEFT SIDE of your range.

To Install Grill:

1. Before installing grill components, be sure controls knobs are in the OFF position.

2. Position the grill burner with mixer tubes and ignitor rod toward the orifices and terminal receptacle. Slide the burner until the tubes and ignitor engage, then lower the burner until it rests in the burner basin.

3. Place the grill grates on top of the rangetop.

Important: Before using the grill for the first time, heat the grill burner to remove the protective shipping coating. Heat the grill burner on HIGH for 10 minutes and use the vent system to remove any smoke.

To Remove Grill:

1. Be sure control knobs are in the OFF position and the grill components are cool.

2. Remove grill grates.

3. Lift the burner up slightly. Slide the burner away from the orifices and terminal receptacle.

Using the Grill

• Before the first use, wash your new grill grates in hot soapy water, rinse and dry. Then “season” the surface by wiping on a thin coating of cooking oil. Remove excess oil by wiping with paper towel.

This procedure should be repeated when either:

a) cleaning in the dishwasher since the detergent may

remove seasoning

b) anytime a sugar-based marinade (for example,

barbecue sauce) is going to be used.

• Preheat the grill on HIGH for 5 minutes. Preheating improves the flavor and appearance of meats and quickly sears the meat to help retain the juices.

• Use nonmetallic spatulas or utensils to prevent damaging

the nonstick grill grate finish.

• Excessive amounts of fat should be trimmed from meats. Only a normal amount is necessary to produce the smoke needed for that smoked, “outdoor” flavor. Excessive fat can create cleaning and flare-up problems.

• Allowing excessive amounts of grease or drippings to

constantly flare-up voids the warranty on the grill grates.

• Excessive flare-ups indicate that either the grill interior needs to be cleaned, that excessive amounts of fat are in the meat or the meat was not properly trimmed.

• Grease drippings will occasionally ignite to produce harmless puffs of flame for a second or two. This is a normal part of the cooking process. Important: For information on the grease cup, see page 8.

• NEVER LEAVE GRILL UNATTENDED DURING

GRILL OPERATION.

• Should excess grease cause sustained flare-ups:

1. Turn on the fan manually.

2. Immediately turn grill controls to OFF.

3. Remove meat from grill.

Cont.

Notes:

• Do not use aluminum foil inside the grill area, or cover grates with aluminum foil.

• Do not use charcoal or wood chips in the grill area.

• Do not allow grill basin pan to become overloaded with grease. Clean frequently.

• Do not cover grates completely with meat. Leave air space between each steak, etc. to allow proper ventilation as well as prevent flare-ups.

• Do not use grill to heat cooking utensils.

Ventilation System

The built-in ventilation system removes cooking vapors, odors and smoke from foods prepared on your cooktop and grill.

• To operate the ventilation system manually, push the Vent Fan pad located on the electronic control. Push once for Low, push again for High and a third time to turn the fan Off.

• The ventilation system will operate automatically when the

grill element is in use.

• The fan can be used to remove strong odors from the

kitchen as when chopping onions near the fan.

➞

Grilling Tips

• Be sure to follow directions for using the grill.

• Suggested cooking times and control settings (see page

16) are approximate due to variations in the foods and electrical voltage.

• For best results, buy top grade meat. Meat that is at least

/4 inch thick will grill better than thinner cuts.

• Score fat on edges of steak, but do not cut into meat, to prevent curling while cooking.

• For the attractive “branded” look on steaks, be sure grill is preheated. Allow one side of meat to cook to desired doneness, or until juices appear on the top surface, before turning. Turn steaks and hamburgers just once. Manipulating food causes loss of juices.

• When basting meats or applying sauces to foods, remember that excessive amounts accumulate inside your grill and do not improve the food flavor.

Apply sauces during the last 15 to 20 minutes of cooking time unless recipe specifies otherwise. Plus, anytime a sugar-based marinade (for example barbecue sauce) is going to be used, the grates should be “seasoned” prior to preheating. (See Using the Grill section, page 14.)

• There are many meat marinades which will help tenderize less expensive cuts of meat for cooking on the grill.

• Certain foods, such as poultry and non-oily fish, may need some extra fat. Brush with oil or melted butter occasionally while grilling.

• Use tongs with long handles or spatulas for turning meats. Do not use forks as these pierce the meat, allowing juices to be lost.

Care and Cleaning of the Ventilation System

• Air Grille: The air grille lifts off easily. Wipe clean or wash in dishwasher or sink with mild household detergents. To prevent scratching the surface, do not use abrasive cleaners or scrubbing pads.

FILTER

• Filter: Turn off ventilation system before removing. The filter is a permanent type and should be cleaned when soiled. Clean in sink with warm water and detergent or in dishwasher.

IMPORTANT: DO NOT OPERATE SYSTEM WITHOUT FILTER. Filter should always be placed at an angle. As you

face the front of the range, the top of the filter should rest against the left side of the vent opening. The bottom should rest against the right side of the vent chamber at the bottom. Important: If filter is flat against the fan wall,

ventilation effectiveness is reduced.

• Ventilation Chamber: This area, which houses the filter, should be cleaned in the event of spills or whenever it becomes coated with a film of grease. It can be cleaned with paper towel, damp cloth, or sponge and mild household detergent or cleanser.

Important: The oven vent is located under the right side of the air grille. When using or cleaning the oven, hot and moist air may be noticed in this area. The area near the vent may become hot enough to cause burns. Be careful not to spill anything into this vent. The air grille must be

removed before the self-clean cycle.

Grill Guide

Preheat grill on High 5 minutes for best flavor.

FOODS SETTING COOKING TIME PROCEDURE

Steak (1 - 11/4” thick): Rare High 14 to 24 minutes Turn after 7 to 12 minutes.

Medium High 18 to 30 minutes Turn after 9 to 15 minutes. Well High 24 to 34 minutes Turn after 12 to 17 minutes.

Hamburgers (3-4 oz.) 9 20 to 25 minutes Turn after half the time.

Pork Chops (1/2 - 3/4” thick) 9 25 to 45 minutes Turn occasionally.

Ham Slices (1/2” thick) High 15 to 20 minutes Turn once.

Fully-Cooked Sausages:Hot Dogs High 7 to 12 minutes Turn occasionally.

Polish High 13 to 16 minutes Turn once.

Fresh Sausage: Links & Patties 9 15 to 25 minutes Turn occasionally.

Chicken: Boneless Breasts 9 20 to 30 minutes Turn occasionally.

Bone-in Breasts, Drumsticks 9 30 to 50 minutes Turn occasionally. Brush with marinade and Thighs or glaze during last 10 minutes.

Fish: Steaks (1” thick) 9 20 to 25 minutes Brush with butter. Turn after half the time.

Shrimp: (skewered) 9 10 to 20 minutes Turn and brush with butter or marinade

frequently.

Garlic Bread, Bruschetta High 4 to 6 minutes Turn after half the time. Hot Dog Buns, Hamburger Buns 9 1 to 2 minutes

Fruits & Vegetables: Pineapple Rings High 8 to 10 minutes Turn after half the time.

Pepper Rings High 7 to 9 minutes Brush with oil. Turn after half (1/2” rings) High 8 to 12 minutes Brush with butter. Turn occasionally. (1/2” lengthwise slices)

Important: This chart is a suggested guide. Cooking times and control settings are approximate due to variations in meats and gas pressure.

OVEN COOKING

Control Panel

A B C D E F G H

I J K L M N O P

The control panel is designed for ease in programming. The display window shows options for each function and moves from step to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake operation.

A Rapid Preheat Use to decrease preheating time. B Convect Use for convection baking and roasting. C Bake Use for baking and roasting. D Broil Use for broiling and top browning. E TIMER 1 Sets timer. F Display Displays oven functions, options and

window time of day.

G TIMER 2 Sets timer. H Number Pads Use to enter time and temperature,

or to enter Favorites names.

I Favorites Use to access, program or save

baking cycles.

J More Options Use to access additional features. K Clean Use to set self-clean cycle. L Setup Use to view or change factory

default settings.

M Vent Fan Activates the ventilation fan on

the cooktop.

N Oven Light Use to turn the oven light on or off. O CANCEL Cancels all operations except Timer,

Clock, Favorites and Setup.

P Quickset pads Use to select options in display

window (next to display window on both sides).

Quickset Pads

Quickset pads are located on each side of the display window and are used to select the desired function or option in the display window. To select the option or function, press the Quickset pad next to the word.

If you need to back out of a function or option in the display, press the Back pad. When your programming is complete, press the Enter pad or wait four seconds and the function will start automatically.

Up arrows indicate additional screens with additional options. Press the Quickset pads next to the arrows to scroll through the display.

Important: Four seconds after entering the function, option, number or letter, the function will automatically be entered. If more than 30 seconds elapse between steps in programming, the function will be canceled and the display will return to the previous display.

Clock

Setting the Clock:

1. Press the Setup pad.

2. Select CLOCK using the Quickset pads.

3. Select TIME.

4. Enter the time using the number pads.

5. Press Enter pad.

6. Select AM or PM in 12 hour mode. (For 24 hour clock, see page 18.)

7. To exit the Setup mode, press Setup pad.

Activating and canceling the clock/day of week display:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DISABLE is displayed.

4. Select DISABLE.

5. Select TIME.

6. Select OFF to turn the clock display off, or select ON to turn the clock display on.

7. Select OFF to turn the day of the week display off. Select ON to turn the weekday display on.

8. To exit the Setup mode, press Setup pad.

Entering the day of the week:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DAY is displayed.

4. Use Quickset arrow to scroll through the days.

5. Select day desired.

6. To exit the Setup mode, press Setup pad.

To set the clock for a 12 or 24 hour format:

The clock can be set to display time in either a 12 hour or 24 hour format.

1. Press the Setup pad.

2. Select CLOCK.

3. Use the arrow to scroll to the next screen.

4. Select 12/24 HOUR.

5. Select 12 HR or 24 HR.

6. To exit Setup mode, press Setup pad.

Timers

Setting the Timers (Timer 1 or Timer 2):

1. Press TIMER 1 or TIMER 2 pad.

2. Press one of the displayed times using the Quickset pads, or press the number pads to enter the desired time.

Important: Each press of the displayed time choices adds additional time. For example, pressing “10 MIN” three times provides 30 minutes on the timer (0:30).

3. Press Enter pad.

Changing the amount of time entered once the Timer starts:

1. Press the TIMER 1 or TIMER 2 pad once.

2. Press the displayed times on the Quickset pads repeatedly until the desired time is entered.

3. Press the number pads to enter the new desired time.

4. Press Enter pad.

Canceling the Timer:

1. Press the TIMER 1 or TIMER 2 pad twice.

If both Timers are active:

If the desired Timer is already in the foreground, press once for edit mode and twice to cancel the Timer. If the desired Timer is not in the foreground, follow the steps below.

1. Press the desired TIMER pad once. The selected Timer will come to the foreground.

2. Press the TIMER pad a second time to access the edit mode in order to make changes.

3. Pressing the TIMER pad a third time will cancel the Timer.

Changing the Timer beeps:

The signal beeps for TIMER 1 and TIMER 2 can be changed. The options available are two beeps every thirty seconds, two beeps every sixty seconds or one beep only. The default setting is one beep.

1. Press the Setup pad.

2. Select the arrow to scroll until TONES is displayed.

3. Select TONES.

4. Select TIMERS TONES.

5. Select the desired timer beep format (2-30 SEC., 2-60 SEC. or 1 BEEP).

6. Press Setup pad to exit Setup mode.

Locking the Control and Oven Door

The oven control and oven door can be locked to prevent accidental programming. If an oven function is currently being used, the control and door cannot be locked.

To lock the control and door:

Press the Back and Enter pads at the same time, holding for three seconds or until CONTROL LOCKED appears in the display.

To unlock the control and door:

Press the Back and Enter pads at the same time, holding for three seconds. UNLOCKING DOOR will appear in the display when the control and door are unlocking.

Baking

To set Bake:

1. Press the Bake pad.

2. Select the oven temperature using the Quickset pads.

Enter the desired temperature using the number pads. Press Enter pad to set.

• The temperature can be set from 170° F to 550° F in 5° increments.

• After three seconds, the oven will begin to preheat. BAKE and PREHEAT will appear in the display along with 100° or the actual oven temperature, whichever is higher.

• The temperature in the display will increase in 1° increments until the oven reaches the preset temperature. Allow about 15 minutes for the oven to preheat.

• When the oven is preheated, the oven will beep and PREHEAT will no longer be displayed.

3. At the end of cooking, turn the oven off by pressing the CANCEL pad. Remove food from the oven. The oven will continue operating until the CANCEL pad is pressed.

Notes:

• If more than thirty seconds elapse between pressing a pad and pressing a number pad, the display will return to the previous display.

• Whenever the temperature appears in the display, the oven is heating.

• To change the oven temperature during cooking, press the Bake pad and select a displayed temperature or use the number pads to enter the desired temperature.

• The oven will automatically shut off after 12 hours if it is accidentally left on. To set a Sabbath Mode, see Sabbath Mode, page 31.

Bake Options

Cook & Hold and Delay options are available when baking. When using the Cook & Hold option, the oven begins to heat immediately after the control has been set. Then, the oven cooks for a specified length of time. When that time has elapsed, the oven will automatically reduce temperature to 170° F and keep the food warm for up to an hour and then automatically turn off.

When using Delay, the oven begins to cook later in the day. Set the amount of time that you want to delay before the oven turns on and how long you want to cook. The oven begins to heat at the selected time and cooks for the specified length of time. When that time has elapsed, the oven will keep the food warm for up to an hour then automatically turn off.

To set Cook & Hold:

1. After Bake has been programmed, press the More Options pad.

2. Select COOK/HLD.

3. Select the amount of time you want to bake by pressing the Quickset pads or the number pads.

4. Press the Enter pad.

5. COOK TIME, the cook time countdown, PREHEAT, BAKE and the actual temperature will be displayed.

The oven will cook for the selected time, then keep food warm for one hour.

To set a Delay:

1. After Bake has been programmed, press the More Options pad.

2. Select DELAY.

3. Select the amount of time you want to delay the start of cooking using the displayed times or the number pads.

4. Select the amount of time you want to cook using the displayed times or the number pads.

5. The display will show BAKE, the temperature, the delay time and the cook time countdown.

6. When the delay time has expired, the oven will begin heating. COOK TIME, the cook time countdown, PREHEAT, BAKE and the actual oven temperature will be displayed.

CAUTION

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry or seafood.

Convect

Convection uses a fan to circulate hot air evenly over, under and around the food. As a result, foods are evenly cooked and browned, often in shorter times, at lower temperatures and with the flexibility of using more than one rack at a time.

3. Select the oven temperature using the Quickset pads

Notes:

• The oven control comes from the factory set for Auto Convect Conversion. When using Convect Bake and Convect Pastry enter the conventional baking temperature. The control automatically converts the temperature to 25° less than the conventional temperature.

• When using Convect Roast the temperature will not be automatically reduced. Enter the conventional roasting temperature and time. The control then lets you know when 75% of the time has elapsed and alerts you to check the food for doneness.

• To turn Auto Convect Conversion off, see page 30.

Convect Options

Cook & Hold and Delay options are available when convect cooking. See page 24 for information on how to program a Cook & Hold or Delay option.

CONVECT CONVECT CONVECT

BAKE ROAST PASTRY

Multiple-Rack Whole Chicken Frozen Pie

Baking of Whole Turkey Turnovers

Cookies/Biscuits Vegetables Cream Puffs

Breads Pork Roasts Puff Pastry

Casseroles Beef Roasts

Tarts/Tortes

Cakes

Convect Bake

To set Convect Bake:

1. Press the Convect pad.

2. Select CNVT BAKE using the Quickset pads.

Enter the desired temperature using the number pads. Press Enter pad to set.

• The temperature can be set from 195° F to 550° F degrees in 5° increments. If Auto Convect Conversion is turned off, you can set 170° F.

• After three seconds, the oven will begin to preheat. CNVT BAKE and PREHEAT will appear in the display along with 100° or the actual oven temperature, whichever is higher.

• The temperature in the display will increase in 1° increments until the oven reaches the preset temperature. Allow about 15 minutes for the oven to preheat.

• When the oven is preheated, the oven will beep and PREHEAT will turn off and CNVT BAKE will be displayed. AUTO will be displayed if Auto Convect Conversion feature is turned on.

• Place food in the oven.

4. At the end of cooking, turn the oven off by pressing the CANCEL pad. Remove food from the oven. The oven will continue operating until the CANCEL pad is pressed.

Rapid Preheat

Use to decrease preheating time when using Bake or Convect Bake. Use for all foods when baking on one rack.

• After Bake or Convect Bake has been programmed and

activated, press the Rapid Preheat pad.

• 1 RACK ONLY will display, after 10 seconds the display will

show RAPID and PREHEAT.

To return to Standard Preheat:

• Press Rapid Preheat pad again. This will provide standard

preheat and PREHEAT and the selected function will be displayed.

Notes:

• For best results, use rack position 2 or 3 when using the Rapid Preheat option.

• For optimum baking and browning results, Rapid Preheat is not recommended when baking on multiple racks.

Convect Roast

To set Convect Roast:

1. Place food in the oven.

2. Press the Convect pad.

3. Select CNVT ROAST using the Quickset pads.

Convect Pastry

Convect Pastry is designed to bake pastry items such as frozen pies, turnovers, cream puffs and puff pastry. Use one, two or three racks while using this feature.

1. Press the Convect pad.

2. Select CNVT PASTRY using the Quickset pads.

4. Select the oven temperature using the Quickset pads.

Enter the desired temperature using the number pads. Press Enter pad to set.

• The temperature can be set from 170° F to 550° F degrees in 5° increments.

5. Enter desired cook time. Enter the conventional roasting time using the number pads.

• After three seconds, the oven will begin to heat. CNVT

ROAST will appear in the display along with 100° or the actual oven temperature, whichever is higher.

• The temperature in the display will increase in 1°

increments until the oven reaches the preset temperature.

• Cook time will begin to count down.

6. At 75% of the cooking time the oven will beep to let you know to check food. Check food using a meat thermometer. If food is done, take food out of oven and press CANCEL pad to turn oven off.

7. If food is not done, continue roasting. Once the set time has elapsed the oven will automatically

go into Keep Warm mode for 1 hour and then shut off. If food is taken from the oven before the hour has elapsed, press CANCEL pad.

3. Select the oven temperature using the Quickset pads.

Enter the desired temperature using the number pads. Press Enter pad to set.

• The temperature can be set from 195° F to 550° F degrees in 5° increments.

• After three seconds, the oven will begin to preheat. CNVT PASTRY and PREHEAT will appear in the display along with 100° or the actual oven temperature, which ever is higher. AUTO will display if the Auto Convect Conversion feature is turned on.

• The temperature in the display will increase in 1° increments until the oven reaches the preset temperature. Allow about 15 minutes for the oven to preheat.

• When the oven is preheated, the oven will beep and PREHEAT will turn off and CNVT PASTRY will be displayed.

4. At the end of cooking, turn the oven off by pressing the CANCEL pad. Remove food from the oven. The oven will continue operating until the CANCEL pad is pressed.

Notes:

• If the recipe suggests preheating the oven, add 15 minutes to cook time.

• If Auto Convect is off, roast time will not be required.

Broil

For optimal results, preheat for five minutes with the door closed and use a pan designed for broiling. Oven door should be open to the broil stop position (about 4 inches) when broiling.

To set Broil:

1. Place the oven rack in the proper rack position (see Broiling Chart).

2. Press the Broil pad.

3. Select HIGH – 550° F for high broil.

Select LOW – 450° F for low broil.

• The oven has a variable broil feature which means that

a lower broil temperature can be selected (300°-550° F). To select a lower temperature, press the appropriate number pads. Press Enter pad to set the lower temperature.

4. Preheat the oven for five minutes.

5. Place food in the oven and close the door to the broil stop position.

6. Press the CANCEL pad when broiling is done.

Notes:

• See Broiling Chart for foods and broiling times.

• If more than 30 seconds elapse between pressing the Broil pad, Quickset pads, or number pads, the oven will not be set and the display will return to the previous display.

• HIGH is used for most broiling. Use a lower broil temperature when broiling longer-cooking foods. The lower temperature allows food to cook to the well done stage without excessive browning.

• Expect broil times to increase and browning to be slightly lighter if the appliance is installed on a 208 volt circuit.

• Food should be turned halfway through broiling time.

• Broil times may be longer when lower broiling temperatures are selected.

Broiling Chart

SUGGESTED RACK

FOODS BROIL TIME POSITION*

Beef (broiled to 165° F)

6 Hamburgers, 1/2” thick 10 – 12 minutes 4 2 Ribeye Steaks, 1” thick 18 - 22 minutes 4 2 New York Strip Steaks, 1” thick 18 - 22 minutes 4 2 T-Bone Steaks, 1” thick 18 - 22 minutes 4

Poultry (broiled to 170° F on Low) Low Broil

4 Boneless/Skinless Breasts 12 – 15 minutes 4 4 Bone-In Chicken Breasts 20 – 33 minutes 3

Pork (broiled to 160° F)

4 Boneless Pork Chops, 1” thick 20 - 28 minutes 4 4 Bone-In Pork Chops, 1” thick 25 - 28 minutes 4 Ham Slice, 1” thick 12 - 16 minutes 4

Fish (broiled to 140° F)

4 Swordfish Steaks, 1” thick 10 - 14 minutes 3 2 Halibut Steaks, 1” thick 10 - 14 minutes 3 Orange Roughy, 1 ” thick 10 - 12 minutes 4 Shrimp (16-20 ct. per lb.) 8 - 10 minutes 4 2 Salmon Fillets, 1/2” thick 8 - 12 minutes 4 2 Salmon Steaks, 1” thick 10 - 14 minutes 3

*Important: To reduce browning and excess smoke when broiling, use a lower rack position and increase the broil time.

Oven Fan

A convection fan is used to circulate hot air in the oven when the convection feature is selected.

Important: The convection fan will automatically stop when the oven door is opened.

Oven Vent

The oven vent is incorporated into the downdraft ventilation system on the cooking surface.

When the oven is in use, the area near the oven vent may become hot enough to cause burns. Do not block the vent opening for best baking results.

Oven Light

The oven light automatically comes on when the door is opened. When the door is closed, press the Oven Light pad to turn the oven light on and off. A beep will sound every time the Oven Light pad is pressed. If the oven light is on when the door is opened, the light will go off when the door is closed.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or sugary spills, as they may discolor the porcelain enamel. Use the correct pan size to avoid spillovers and boilovers. Do not

place utensils or aluminum foil directly on the oven bottom.

Oven Racks

CAUTION

• Do not attempt to change the rack position when the oven is hot.

• Do not use the oven for storing food or cookware.

Three standard flat racks were packaged for the oven.

To remove:

1. Pull forward to the “stop” position.

2. Lift up on the front of the rack and pull out.

To replace:

1. Place rack on the rack support in the oven.

2. Tilt the front end up slightly; slide rack back until it clears the lock-stop position.

3. Lower front and slide into the oven.

Rack Positions

RACK 5 (highest

position): Used for two-rack

cooking and broiling.

RACK 4:

Used for two-rack baking and broiling.

RACK 3:

Used for most baked goods on a cookie sheet or jelly roll pan, layer cakes, fruit pies, or frozen convenience foods.

RACK 2:

Used for roasting small cuts of meat, casseroles, baking loaves of bread, bundt cakes, custard pies, frozen pies or two-rack baking.

RACK 1:

Used for roasting large cuts of meat and poultry, dessert souffles, angel food cake, or two-rack baking.

MULTIPLE RACK COOKING: Two rack: Use rack positions 2 and 5 or 1 and 4. Three rack (convection only): Use rack positions 1, 3

and 5 (see illustration).

Notes:

• When convect baking on two or three racks, check foods

at the minimum suggested time to avoid over-browning or over-cooking.

• Do not cover an entire rack with aluminum foil or place foil

on the oven bottom. Baking results will be affected and damage may occur to the oven bottom.

Baking Layer Cakes on Two Racks

For best results when baking cakes on two racks with or without convection, use racks 2 and 5.

Place the cakes on the rack as shown.

Three-rack Convection Cooking

5 Flat

3 Flat

1 Flat

OPTIONS

More Options

Cook & Hold

1. Press the More Options pad.

2. Select COOK/HOLD.

3. Enter cook time using Quickset pads or the number pads.

4. Select BAKE or CONVECT.

5. When BAKE is pressed, select the temperature using Quickset pads or the number pads.

6. When CONVECT is pressed, select CNVT BAKE, CNVT ROAST or CNVT PASTRY, then select the desired temperature using the Quickset pads or the number pads.

The oven will cook for the selected time, then Keep Warm for one hour. The oven will automatically turn off.

Important: If the recipe recommends preheating the oven, add 15 minutes to the cook time.

5. The display will show CONVECT DELAY, the selected function, the preset temperature and the delay time countdown. When the delay time has expired, the cook time will be displayed and the oven will begin to preheat.

To set Delay Clean:

1. Follow “Delay” steps 1-4 (see below left).

2. REMOVE RACKS will show in the display. Remove the racks from the oven and select CONTINUE.

3. Set LIGHT soil level by entering 200 using the number pads for two hours of cleaning time. Select MEDIUM or HEAVY soil level using the Quickset pads. There is a brief delay while the door locks.

4. DELAY CLEAN, the cleaning time, the delay time and unlock time (based on the selected soil level) will show in the display. When the delay time has expired, the clean time will be displayed and the oven will begin to preheat.

For more information on self-cleaning, see pages 5-6.

CAUTION

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry, or seafood.

Delay

1. Press the More Options pad.

2. Press the arrow until DELAY is displayed.

3. Select DELAY.

4. Select Delay time using Quickset pads or the number pads.

5. Select BAKE, CONVECT or CLEAN, then select temperature using the Quickset or number pads.

To set Delay Bake:

1. Follow “Delay” steps 1-4 (see above).

2. Select from the displayed temperatures or use the number pads to enter the temperature.

3. Select the time to cook from the displayed times or use the number pads to enter the cooking time.

4. The display will show DELAY TIME, the selected function, the preset temperature and the delay time countdown. When the delay time has expired, the cook time will be displayed and the oven will begin to preheat.

To set Delay Convect:

1. Follow “Delay” steps 1-4 (see above).

2. Select BAKE, ROAST or PASTRY.

3. Select from the displayed temperatures or use the number pads to enter the temperature.

4. Select the time to cook from the displayed times or use the number pads to enter the cooking time.

Proofing

The Proofing feature can be used to raise yeast-based bread products prior to baking. There are two proofing methods available – Rapid and Standard.

Standard proofing in the oven protects dough from room temperature changes or drafts that commonly affect proofing done on the countertop.

Rapid proofing provides faster proofing results than countertop or Standard proofing, without harming the yeast.

1. Press More Options pad.

2. Select PROOFING.

3. Select RAPID or STANDARD.

4. When proofing is complete, remove the dough from the oven and press the CANCEL pad.

Notes:

• For any dough that requires one rise, either Standard or Rapid Proofing can be used.

• When using frozen bread dough, choose RAPID PROOFING. There is no need to thaw dough before proofing.

• For dough requiring two rises, Standard Proofing must be used for the first rising period. Either Standard or Rapid Proofing can be used for the second rise.

• If oven temperature is too high for proofing, OVEN COOLING will appear in the display.

Keep Warm

The Keep Warm feature is used to safely keep hot foods warm or for warming breads and plates.

1. Press More Options pad.

2. Press the arrow to scroll.

3. Select KEEP WARM.

4. Select one of the displayed temperatures or enter desired temperature using the number pads. Temperatures can be selected between 145° and 190° F.

5. KEEP WARM and the temperature will be displayed.

6. When oven has preheated, a beep sounds and KEEP WARM and the temperature will be displayed.

7. When finished, press the CANCEL pad and remove food or plates from the oven.

To Warm Dinner Rolls:

• Cover rolls loosely with foil and place in oven.

• Press More Options pad.

• Select KEEP WARM.

• Select 170° temperature. Warm for 12-15 minutes.

To Warm Plates:

• Place two stacks of up to four plates each in the oven.

• Press More Options pad.

• Select KEEP WARM.

• Select 170° temperature.

• Warm for five minutes. Turn off the oven by pressing the

CANCEL pad and leave plates in the oven for 15 minutes more.

• Use only oven-safe plates, check with the manufacturer.

• Do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or breakage.

Notes:

• Food should be hot when placed in oven.

• For optimal food quality, foods should be kept warm for no longer than 1 hour.

• To keep foods from drying, cover loosely with foil or a glass lid.

Meat Probe

Using the probe supplied with your oven assures excellent roasting results every time.

1. Insert the probe into the food item. For meats, the probe tip should be located in the center of the thickest part of the meat and not into the fat or touching a bone.

2. Insert the probe plug into the receptacle located on the top right of the oven. Be sure to insert plug into the receptacle all the way.

3. Press More Options pad.

4. Press the arrow to scroll.

5. Select MEAT PROBE.

6. Set the internal food temperature desired by selecting one of the displayed temperatures or enter the temperature using the number pads. The probe temperature can be set from 100° - 185° F. If the meat probe is not inserted, INSERT PROBE will be displayed.

7. Select BAKE or CONVECT.

8. Set the oven temperature by selecting one of the displayed temperatures or enter the temperature using the number pads.

Important: If the probe is removed from the oven receptacle at any time during the cooking process, the control will prompt INSERT PROBE. If the probe is not reinserted within 30 seconds, the program will be canceled and the oven will turn off.

When BAKE is selected:

• The display will briefly show the selected temperatures for the oven and probe.

• After 10 seconds, the display will show the actual oven temperature and actual probe temperature.

When CONVECT is selected:

• Select CNVT BAKE, CNVT ROAST or CNVT PASTRY.

• Set the oven temperature by selecting one of the displayed temperatures or enter the temperature using the number pads.

• The display will briefly show the selected temperatures for the oven and probe.

• After 10 seconds, the display will show the actual oven temperature and actual probe temperature.

9. When the selected internal temperature of the food has been reached, the oven will shut off and a beep will sound.

10. Remove the probe from the oven receptacle. The probe will be hot. Hold probe plug with an oven mitt or potholder when removing from the oven.

Notes:

• The probe must be removed from the oven when it is not being used.

• Because of the excellent insulation of the oven, the retained heat continues to cook the food after the beep has sounded and the oven has turned off. For this reason, it is important to remove the food from the oven as soon as the beep sounds.

• Use the handle of the probe for inserting or removing.

Do not pull on the cable.

• The probe is hot after cooking – use a potholder or oven mitt to remove.

• To clean cooled probe, wipe with a soapy dishcloth.

Do not submerge probe in water or wash in dishwasher.

• Gently close the door until the spacer magnet makes contact with the oven door. The magnet will hold the spacer in the proper position during the drying process and allows the door to be opened at any time during drying without losing proper positioning.

Important: If the spacer is not placed correctly, the convection fan will not operate.

2. Press Convect pad.

3. Press the arrow to scroll.

4. Select DRYING.

5. Select a displayed temperature or enter a temperature with the number pads. Temperatures can be set between 100° F and 200° F.

6. DRYING and the temperature will be displayed. PREHEAT will be displayed until the programmed temperature is reached.

7. When drying is complete, remove food from oven and press CANCEL pad.

Follow the Drying Guide on page 27 for drying times. Check foods at minimum times given. Cool foods to room temperature before testing for doneness.

Suggested Internal Food Temperatures

INTERNAL

FOOD TEMPERATURE

Ground Beef 165° F Fresh Beef, Veal, Lamb Medium Rare 145° F

Medium 160° F Well Done 170° F

Chicken, Turkey Whole 180° F

Breast 170° F

Pork Medium 160° F

Well Done 170° F Ham, Precooked 140° F

Drying

For best results, use a drying rack. A drying rack allows air to circulate evenly around the food.

The convection fan will operate during the drying procedure.

To set Drying:

1. The oven door needs to be opened slightly to allow moisture to escape from the oven during the drying process.

• Open the oven door slightly.

• Place the magnetic door spacer

(Part No. 8010P146-60) over the plunger switch at the upper right side of the oven frame. The spacer provides a gap between the oven frame and the oven door to allow moisture to escape.

Notes:

• To purchase a drying rack, contact your Jenn-Air dealer for the “DRYINGRACK” Accessory Kit or call 1-800-JENNAIR.

• Most fruits and vegetables dry well and retain their color when dried at 140° F. Meat and jerky should be dried at 145° - 150° F. For optimal flavor, dry herbs at 100° F, however, at this lower temperature expect extended drying times of up to 8 hours.

• The length of drying times vary due to the following:

Water and sugar content of food, size of food pieces, amount of food being dried, humidity in the air.

• Check foods at the minimum drying time. Dry longer if necessary.

• Fruits that turn brown when exposed to air should be treated with an antioxidant. Try one of the following methods:

1. Dip fruit in a mixture of two parts bottled lemon juice

to one part cool water.

2. Soak fruit in a solution of 1 tsp. ascorbic acid or

commercial antioxidant to 1 quart of cold water.

• Foods may drip during the drying process. After drying high acid or sugary foods, clean the oven bottom with soap and water. The porcelain oven finish may discolor if acidic or sugary food soils are not wiped up prior to high heat or a self-cleaning cycle.

• More than one rack of food may be dried at the same time. However, additional drying time is needed.

• Refer to other resources at your local library or call your local County Extension service for additional information.

Drying Guide

APPROX.

FRUITS VARIETIES BEST PREPARATION DRY TIME TEST FOR DONENESS

FOR DRYING at 140° F ** AT MIN. DRY TIME

Apples* Firm varieties: Graven Wash, peel if desired, core and slice 4-8 hours Pliable to crisp. Dried

Stein, Granny Smith, into 1/8” slices. apples store best when Jonathan, Winesap, they are slightly crisp. Rome Beauty, Newton.

Apricots* Blenheim/Royal most Wash, halve, and remove pits. 18-24 hours Soft, pliable.

common. Tilton also good.

Bananas* Firm varieties Peel and cut into 1/4” slices. 17-24 hours Pliable to crisp.

Cherries Lambert, Royal Ann, Wash and remove stems. Halve and 18-24 hours Pliable and leathery.

Napoleon, Van or Bing. remove pits.

Nectarines Freestone varieties. Halve and remove pits. Peeling 24-36 hours Pliable and leathery. and Peaches* is optional but results in

better-looking dried fruit.

Pears* Bartlett Peel, halve and core. 24-36 hours Soft and pliable.

Pineapple Fresh or canned. Wash, peel and remove thorny eyes. Canned: Soft and pliable.

Slice lengthwise and remove the 14-18 hours small core. Cut crosswise into Fresh: 1/2” slices. 12-16 hours

Orange and Select rough-skinned fruit. Wash well. Thinly peel the outer 1-2 hours Tough to brittle. Lemon Peel Do not dry the peel of fruit 1/16 to 1/8” of the peel. Do not use

marked “color added”. the white bitter pith under the peel.

VEGETABLES

Tomatoes Plum, Roma Halve, remove seeds. Place tomatoes 12-18 hours Tough to crisp.

skin side up on rack. Prick skins.

Carrots Danvers Half Long, Do not use carrots with woody fiber 4-8 hours Tough to brittle.

Imperator, Red Cored or pithy core. Wash, trim tops and Chantenay peel if desired. Slice crosswise or

diagonally into 1/4” slices. Steam blanch for 3 min.

Hot Peppers Ancho, Anaheim Wash, halve and seed. Prick 4-6 hours Pods should appear

skin several times. shriveled, dark red and crisp.

HERBS

Parsley, Mint, Rinse in cold water. Pat dry with a 1-3 hours Brittle and crumbly. Cilantro, Sage, paper towel. Leave stems on until Oregano leaves are dry, then discard.

Basil Cut leaves 3 to 4” from top of plant 2-5 hours Brittle and crumbly.

just as buds appear. Rinse leaves in cold water.

* Fruits requiring an antioxidant to prevent discoloration and loss of nutrients. Refer to the notes on page 26 for specific methods.

** 12 Hour Off will not occur during drying functions.

Thaw and Serve

Use Thaw and Serve to thaw frozen foods that require thawing, but not cooking, before serving.

To set Thaw-Serve:

1. Place food in the oven on rack 2.

2. Press Convect pad.

3. Press the arrow to scroll.

4. Select THAW-SERVE.

5. Select number of minutes to thaw.

6. THAW-SERVE, COOK TIME and the cook time countdown will be displayed.

7. If thawing is complete before time elapses, press the CANCEL pad and remove food from the oven. When the time has elapsed, the oven will turn off and beep.

Important: This feature is not meant for thawing meats or other foods that need to be cooked before serving.

Thaw and Serve Chart

THAW-SERVE

FROZEN ITEMS* TIME** HINTS

Whole Pies & Cakes 1. Remove frozen food from outer carton and wrapping. • Thawing for 30 minutes makes it easier Pies: Lemon meringue, 2. Place frozen food on rack in middle of oven. to slice whole pies, cakes and

cream, pecan, chocolate, 3. Thaw-Serve 15 minutes for cakes and 30 minutes cheesecake. sweet potato, French silk for pies. • Layer cakes will require only 15 minutes Cakes: Vanilla, chocolate, 4. Remove from oven. before slicing. coconut, and three-layer 5. Slice into individual-size servings and place on plates. • Size and texture of food being thawed cakes, pound cake, 6. Return plates to oven. will affect Thaw-Serve time. Boston cream pie 7. Thaw-Serve for 10 to 30 minutes. • Larger or denser desserts may take

longer to thaw. Individual Servings: 1. Remove frozen food from container. • Cake slices will thaw quicker than pies. Slices of pie, slices of cake, 2. Place on plate. Sweet potato pie slices may require 20 other individual desserts, 3. Place plate on rack in middle of oven. to 30 minutes. eclairs, cream puffs 4. Thaw-Serve for 10 to 30 minutes.

Cheesecake 1. Remove frozen food from outer carton and wrapping.

2. Place frozen food on rack in middle of oven.

3. Thaw-Serve for 30 minutes.

4. Remove from oven.

5. Slice into individual-size servings and place on plates.

6. Return plates to oven.

7. Thaw-Serve for up to 15 minutes if desired.

* Only “Thaw and Serve” or “Ready to Serve” frozen foods can be used with this feature. DO NOT attempt to thaw frozen meats, poultry or seafood.

** It is not necessary to preheat the oven.

FAVORITES

Favorites

Favorites stores the oven mode, cook time and temperature for up to 10 of your favorite recipes. Convection ovens come with five preprogrammed recipes.

To select a recipe from the preset Recipe List:

1. Press Favorites pad.

2. Select RECIPE LIST.

3. Select desired recipe on screen or press arrow key to scroll to the desired recipe.

4. Once the recipe is selected, oven will begin preheating to the set program.

• You may press the More Options pad to add

COOK/HOLD or DELAY.

5. When finished, press the CANCEL pad and remove food from the oven.

To Save the Last Recipe Completed:

(Bake, Convect Bake, Convect Roast, Convect Pastry, Convect Broil, Drying, Keep Warm, Proofing)

1. Press Favorites pad.

2. Select SAVE LAST.

3. Enter the name using the keypads.

• For example, to save lasagna, press the <JKL> pad three

times for “L”; Press the <ABC> pad once for “A”; press the <STU> pad once for “S”. Continue until you’ve finished the word.

4. After each desired letter appears, wait three seconds or press Enter pad before moving on the next letter.

• Up to 14 letters including spaces can be used.

5. When the recipe name has been entered, the last settings will be displayed for a few seconds.

6. RECIPE LIST will then be displayed to scroll through the list.

7. Press Favorites pad to exit the Favorites menu.

To Create a New Favorite Recipe:

1. Press Favorites pad.

2. Press arrow key to scroll through selections.

3. Select CREATE NEW with touchpad on left.

4. Enter the name using the keypads.

• For example, to save lasagna, press the <JKL> pad three

times for “L”; Press the <ABC> pad once for “A”; press the <STU> pad once for “S”. Continue until you’ve finished the word.

• After each desired letter wait three seconds until an underline appears in the next space or press Enter pad before moving on the next letter.

• Up to 14 letters including spaces can be used.

5. Select ENTER to save name.

6. Select cooking mode, such as BAKE, CONVECT BAKE, CONVECT ROAST, etc.

7. Select the oven temperature using the Quickset pads.

Enter the desired temperature using the number pads.

8. Add Cook/Hold by selecting YES or omit Cook/Hold by selecting NO.

9. If you selected YES, enter cook time using the Quickset pads or the number pads.

10. Add Delay by selecting YES or omit Delay by selecting NO.

11. If you selected YES, enter the delay time by using the Quickset pads or the number pads.

12. The control will display programmed settings then return to the Favorites menu.

13. Press Favorites pad to exit the Favorites menu.

To Edit a Saved Recipe:

1. Press Favorites pad.

2. Press arrow key to scroll.

3. Select EDIT RECIPE.

4. Select desired recipe to edit. You may need to press arrow key to find desired recipe.

5. Follow menu to revise recipe settings as desired.

6. The display will return to the Favorites menu. RECIPE LIST will be displayed.

7. Press Favorites pad to exit Favorites menu.

To Delete a Favorite Recipe:

1. Press Favorites pad.

2. Press arrow key to scroll.

3. Select DELETE RECIPE.

4. Find recipe to be deleted. You may need to press arrow key to find desired recipe.

5. The Control will ask again to make sure you want to delete that recipe. Select YES or NO.

6. Press Favorites pad to exit Favorites menu.

To exit out of Favorites at any time, press the Favorites pad.

+ 78 hidden pages