Jenn-Air 8101P549-60 User Manual
JENN-AIR ELECTRIC WARMING DRAWER
JENN-AIR ELECTRIC WARMING DRAWER
INSTALLATION
INSTALLATION
G U I D E
G U I D E
TABLE OF CONTENTS
Before You Begin..................................................................... 1-2
Specifications and Requirements ......................................... 3-6
Guide de l’installation ................................................................. 6
Guía de la Instalación ............................................................... 12
Form No. B/03/03 Part No. 8101P549-60 © 2003 Maytag Appliances Sales Co. Litho U.S.A .
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT:
• Save these instructions for the local
electrical inspector’s use.
• OBSERVE ALL GOVERNING
CODES AND ORDINANCES.
NOTES:
TO INSTALLER:
• Leave these instructions with the
appliance after installation is completed.
TO CONSUMER:
• Keep the User Guide and Installation Instructions for future use.
• This appliance must be properly
grounded.
• Insure that the power cord does not
contact the hot surfaces on the bottom of ovens, cooktops, or any other
appliance.
PRODUCT DIMENSIONS
27 7/16" ProStyle Front
25 1/4" Curved Front
27 7/16" ProStyle Front
25
Including handle
1
23
/4"
1
/4" Curved Front
TOOLS & MATERIALS
NEEDED
• 2" x 4" or 2" x 2" lumber for runners and
brace
• Wood screws and adhesive or other
hardware for installing runners or shelf
to support warmer drawer
• Runners must be level, rigidly mounted
and capable of supporting 150 pounds.
• Saw
• Level
1
/2"
9"
30"
The electrical power cord is located on the
right side of the warming drawer. Locate
the outlet within reach of the 56" long
power cord in adjacent cabinet, within 42"
of the right side or 16" from the left side of
the cutout. A recessed receptacle can be
installed on the right side of the cutout, 7"
maximum from the back of the cabinet.
10
REMOVE PACKAGING
AND
Parts provided: 4 Wood screws
PARTS
• Drill and 1/16" bit
• Phillips screwdriver
PLANNING
The warming drawer may be installed directly into a wall or wall oven cabinetry.
The warming drawer may be installed below a countertop, a single, combo or double
oven or side by side using 2 drawers.
When installing the warming drawer with
a cooktop allow a 2" minimum from bottom of a cooktop burner box to top of
cutout.
A 2" minimum clearance between oven and
warming drawer cutouts is required.
UNPACKING
1.Place carton on a flat surface.
2.Open the top of the carton and lift off the
cardboard spacer.
3.Lift the warming drawer up and out of the
carton.
4.Place the drawer on top of the cardboard
to protect the drawer and the finished
flooring.
5.Remove all packing materials and tape.
6.Locate package containing 4 wood screws
and set aside.
1
GROUNDING THE
APPLIANCE
IMPORTANT (Please read carefully)
FOR PERSONAL SAFETY, THIS
APPLIANCE MUST BE PROPERLY
GROUNDED.
Do not use an extension cord or adapter
plug with this appliance. Follow National
Electrical codes and ordinances.
This warming drawer must be supplied
with 120V, 60Hz, and connected to an
individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit
breaker or time delay fuse.
•A properly grounded 3-prong receptacle
should be located within reach of the
drawer’s 56” long power cord.
• Locate the receptacle in an adjacent cabinet.
–Within 42” of the right side or,
–Within 16” of the left side or,
–A recessed receptacle may be located
on the right side of the cutout,
7” maximum from the back of the
cabinet. In this location, the excess
power cord should be coiled to the
right side of the unit using the cord clip
provided.
IMPORTANT (Please read carefully)
The power cord of this appliance is equipped with
a 3-prong (grounding)
plug that mates with
standard 3-prong
grounding wall receptacle to minimize the possibility of electric
shock. The customer should have the wall
receptacle and circuit checked by a qualified electrician to make sure the receptacle
is properly grounded and has the correct
polarity.
• Where a standard 2-prong wall re-
ceptacle is encountered, it is the
personal responsibility and obligation of the customer to have it replaced with a properly grounded 3prong wall receptacle.
Do not, under any circumstances, cut or remove the third (ground) prong from the power
cord.
Recessed receptacle
7" max. from rear on
right side
Drill 11/2" hole for
power cord for left or
right side outlet
location
DO NOT USE AN EXTENSION CORD.
2
SPECIFICATIONS AND REQUIREMENTS
WHEN INSTALLING BELOW
A
COUNTERTOP
Drawer overlaps will conceal cut edges on
all sides of the opening.
The rough opening for the drawer
must be:
• Depth: 23-1/2" minimum from inside back
to front of cabinet frame.
• Width: 28-1/2"
• Height: 9-1/4"
5" minimum above floor or 1" above toe
kick. 23-1/4" from floor to bottom of cutout is recommended for under countertop
installation.
Install 2 x 4 or
2 x 2 anti-tip
block against
rear cabinet wall
9" from floor to
bottom of block
Electrical outlet
flush with side of
cabinet 7" max.
NOTE: If you are installing in frameless
cabinets, it may be necessary to install 1/2"
wide cleats to accept drawer mounting
screws. See drawer to find exact locations
of mounting screws.
Electrical outlet 42"
max. from right side
7”
WHEN INSTALLING BELOW
A
COOKTOP
Warming drawers are suitable for installation below only certain specified cooktop
models.
See the label attached to the top of the
warming drawer for suitable models.
25”
11/2" Cabinet top
Electrical
outlet 16"
max. from
left side
231/2” Min.
9”
281/2"
2” Min.*
91/4”
*NOTE: When installing warming drawer below a
cooktop allow a 2" minimum from bottom of
cooktop burner box to top of cutout.
36”
Countertop
height
3
WHEN INSTALLING BELOW
WALL OVEN
A
Warming drawers are suitable for installation below only certain specified wall oven
models.
See the label attached to the top of the
warming drawer for suitable models.
Drawer overlaps will conceal cut edges on
all sides of the opening.
The rough opening for the drawer
must be:
• Depth: 23-1/2" minimum from inside back
to front of cabinet frame.
INSTALLATION BELOW A SINGLE OVEN
2 x 2 or 2 x 4 anti-tip
block against rear
wall 9" from floor to
bottom of block
231/2"
Min.
Oven
cutout
9”
91/4"
*NOTE: Additional clearance between cutouts may
be required. Check to be sure that oven supports
above the warming drawer location do not obstruct
the required interior 23
2”
Min.
Allow 5/8"
overlap on
all sides
1
/2" depth and 91/
231/4"
101/2"
"
height.
4
• Width: 28-1/2"
• Height: 9-1/4"
• Allow 2" minimum between oven and
drawer cutouts for clearance of overlaps.
NOTE: If you are installing in frameless
cabinets, it may be necessary to install 1/2"
wide cleats to accept drawer mounting
screws. See drawer to find exact locations
of mounting screws.
NOTE: Electrical receptacle can be installed as shown for countertop installations. Do not install receptacle above
the top of the warming drawer cutout.
281/2"
1" Min. above toekick or adjust
to oven installation height
INSTALLATION BELOW A DOUBLE OVEN
2 x 2 or 2 x 4 anti-tip
block against rear
wall 9" from floor to
bottom of block
Oven
cutout
9”
91/4"
1" Min. above toekick
231/2"
Min.
281/2"
281/2"
*NOTE: Additional clearance between cutouts may
be required. Check to be sure that oven supports
above the warming drawer location do not obstruct
the required interior 23
Allow 5/8" overlap
on all sides
2” Min.
30"
30"
30"
1
/2" depth and 91/4" height.
231/4"
101/2"
4
SPECIFICATIONS AND REQUIREMENTS, CONT.
PROVIDE CABINET
SUPPORT
IMPORTANT: When installed below a
single or double oven, check to be sure that
any oven supports above the cutout do not
obstruct the 23-1/2" required depth of the
warming drawer cutout.
2" x 4" or equivalent runners
231/2"
25"
30"
• A 2" minimum clearance between
oven and warming drawer cutouts
is required. Additional clearance may
be required if 2" x 4" blocks are used to
support runners or solid floor of the
oven above.
• The warming drawer may be supported
by either a solid bottom, 2" x 4" or
2" x 2" runners.
ANTI-TIP BRACE
WARNING
• An anti-tip brace must be installed to
prevent the drawer from tipping forward when opened and loaded. Failure
to do so could result in personal injury.
• Before installing anti-tip brace, refer to
Wall Oven or Cooktop installation
instructions for proper clearance of
electrical conduit or power cord.
Install a 2" x 4" or 2" x 2" anti tip brace 9"
above the runners and against the rear cabinet
wall no more than 23" back from the face to
the cabinet frame.
9"
2" x 4" or runners
or solid bottom
INSTALLING THE
DRAWER
1. Slide the left corner into opening and
push power cord into the hole leading to
the outlet location. Thread the cord
through as drawer is being pushed back
into the opening.
If the outlet is installed inside the opening, plug the cord into the outlet. Coil
power cord and install it in the clip on
the right side of the unit. Make sure the
cord does not get trapped by the drawer.
NOTE: Insure that the power cord
does not contact the hot surfaces on the
bottom of ovens, cooktops, or any other
appliance.
2. Push the drawer back until the front
flange is flush to the cabinet front.
3. Open the drawer fully.
4. Drill pilot holes through the holes in the
overlapping frame, one on each corner.
5. Drive wood screws provided into each
corner.
IMPORTANT: Do not operate the
Warming Drawer if the decorative front kit
has not been installed.
• The support must be level and rigidly
mounted, flush with the bottom edge of
the cutout.
• There is no way to level the drawer once
it has been installed. Be sure supports are
level.
• The entire weight of the drawer is supported by the runners or solid floor.
They must be capable of supporting
150 lbs.
5
Loading...