Jenn Air 720-0512 Owner's Manual
G18Y07P-02
TABLE OF CONTENTS
SECTION ONE
Safety Instructions…………………………………
Placement of the Grill ……………………………..
SECTION TWO
Side Shelf Assembly……………………………….
Side Burner Asse mbly……………………………..
Side Burner Hose Quick Disconnect Assembly…
Quick Disconnect Assembly…………… ………….
Side Shelf Handle Assembly & Battery
Installation…………………………………………..
Braking System Operations & Slide-Out Tray
Locking System…………………………………….
Liquid Propane Cylinder Retention System &
Propane Regulator Hook-Up……………………..
Spice Tray & Cooking Griddle Installation……….
SECTION THREE
Gas Hook Up ……………………………………….
Leak Testing………………………… ………………
Installer Final Check……………………………….
SECTION FOUR
Operating Instructions…………………………...
Lighting Instructions……………………………...
Lighting Illustrations……………………………...
To Match Light the Grill…………………………..
Grill Lights…………………………………………
Using the Side Burner……………………………
Care and Maintenance of Side Burner…………
Care and Maintenance of Grill………………….
Troubleshooting…………………………………
1-5
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20-22
23
25
26
27
28
SECTION FIVE
Exploded View…………………………………..
Parts List…………………………………………
SECTION SIX
Grilling Hints……………………………………..
Grill Cooking Chart……………………………..
Grill Recipe Suggestions………………………
SECTION SEVEN
Limited Warranty………………………………...
29
30-31
32
32-34
35-36
37
WARNING
To reduce the risk of fire, burn hazard or other
injury, read this Care and Use Manual carefully
and completely before using your grill.
SAFETY INSTRUCTIONS
RECOGNIZED SAFETY SYMBOLS, WORDS AND LABELS
WARNING
WARNING – Hazards or unsafe
practices which COULD result in severe
personal injury or death.
CAUTION
CAUTION – Hazards or unsafe practices
which COULD result in minor personal
injury.
WARNING
Do not try lighting this appliance without first reading
the “LIGHTING INSTRUCTIONS” section of this
manual.
WARNING
Spiders and insects can nest inside the burners of
the grill and disrupt gas flow. This very dangerous
condition could cause a fire behind the valve panel,
thereby damaging the grill and making it unsafe for
operation.
Inspect the grill at least twice a year.
WARNING
1. Do not store spare liquid propane cylinders under or near thi s appliance.
2. Never fill the cylinder beyond 80 percent capacity.
3. If the information above is not followed exactly, a fire resulting in death or serious injury could
occur.
WARNING
Never attempt to use damaged or obstructed equipment. See your local liquid propane dealer for
repair.
WARNING
Check all gas supply fittings for leaks before each use. Do not use the grill until all connections
have been checked and do not leak. Do not smoke while leak testing. Never leak test with an open
flame.
WARNING
This grill is not intended to be installed in or on
recreational vehicles and/or boats.
WARNING
The rotisserie motor is equipped with a plug and
should be plugged directly into a properly grounded
receptacle in accordance with local codes or, in the
absence of local codes, with the National Electrical
Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1. DO NOT cut or remove the
grounding prong from this plug. Keep any electrical
supply cord and the fuel supply hose away from any
heated surface. Keep the rotisserie motor electric
cord away from the heated surfaces of the grill. When
not in use remove and store the motor in a dry
location.
WARNING
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
WARNING
1. Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any other
appliance.
1
SAFETY INSTRUCTIONS
WARNING
Do not use the grill if the odor of gas is
present. Contact customer service at 1-800554-5799.
When lighting, keep your face and hands as far
away from the grill as possible.
Storage of an outdoor cooking gas appliance
indoor is permissible only if the cylinder is
disconnected and removed from the outdoor
cooking gas appliance.
WARNING
WARNING
1. Attach the coupling half (socket) to the
gas supply line in accordance with
ANSI Z223.1/ NFPA54 FUEL gas
code.
2. Prior to inserting the plug, test the
connection for leaks following the leak
test instructions on page 13. After the
leak test is completed, rinse the
connection with clean water to remove
any corrosive residue.
3. Do not use open flame to test for leaks.
WARNING
WARNING
Do not install this unit into combustible
enclosures. There should be a minimum
clearance of 24 inches from all sides to
combustible materials. Outdoor cooking
appliance shall not be used under
overhead combustible construction.
WARNING
Keep any electrical supply cord away from any
heated surface.
WARNING
Make sure the light switch is on “OFF” position
and power plug is disconnected from power
outlet prior to cleaning the glass cover.
CAUTION
When using the rotisserie burner, remove the
warming rack. High heat from the burner may
cause the warming rack to bend.
WARNING
Failure to properly place the burner over the
orifice could cause a fire to occur behind and
beneath the valve panel, thereby damaging the
grill and making it unsafe to operate.
WARNING
Do not leave the grill unattended while
cooking.
WARNING
Cylinder must be stored outdoors out of the reach
of children and must not be stored in a building,
garage or any other enclosed area.
WARNING
A tank of approximately 12 inches in diameter by 181/2 inches high is the maximum size LP gas tank to
use. You must use an OPD gas tank, which offers
an Overfill Prevention Device.
This safety feature prevents the tank from being
overfilled, which can cause malfunction of the LP gas
tank, regulator and/or grill.
WARNING
The light glass cover should not be in contact with
water or any other liquid when it’s warm. Sudden
change of temperature may cause cracks on glass
WARNING
To ensure continued protection against electric shock:
1. Connect to properly grounded outlets only.
2. Do not expose to rain.
3. Keep extension cord connections dry and off
the ground.
CAUTION
Before cleaning, make sure the gas supply and
control knobs are in the “OFF” position and the
burners have cooled.
CAUTION
When using a match to light the grill make sure to
use the attached lighting rod.
2
SAFETY INSTRUCTIONS
WARNING
Do not attempt to light the grill if gas odor is
present. Contact customer service at 1-800-554-
5799.
When lighting, keep your face and body as far
away from the burner as possible.
BEFORE LIGHTING
Inspect the gas supply hose prior to turning on the
gas. If there is evidence of cuts, wear, or abrasion, it
must be replaced prior to use.
Only the pressure regulator and hose assembly
supplied with the unit should be used. Never
substitute regulators for those supplied with the grill.
Contact customer service for proper replacement.
Screw the regulator (type QCC1) onto the cylinder.
Leak check the hose and regulator connections with
a soap and water solution before operating the grill
(See “Leak Testing” instructions on page 15).
Do not turn “ON” the gas at the LP gas cylinder
unless the quick connect gas hose is properly
connected to the side burner gas pipe system and all
burner valves are in the “OFF” position.
LP GAS CYLINDER WARNING
1. Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
2. A liquid propane cylinder not connected for use
should not be stored in the vicinity of this or
any other appliance.
3. Do not store spare liquid propane gas cylinders
under or near this appliance.
4. Never fill the cylinder beyond 80 percent
capacity.
5. Liquid propane cylinders must be fitted with an
Overfill Protection Device (OPD).
6. If the information above is not followed exactly,
a fire causing death or serious injury may
occur.
USING THE SIDE BURNER
nspect the gas supply hose prior to turning on
I
the gas. If there is evidence of cuts, wear or
abrasion, it must be replaced prior to use. Do not
use the side burner if gas odor is present.
Keep a spray bottle of soapy water near the grill
and check the connections before each use.
ROTISSERIE DRIVE MOTOR
To ensure continued protection against electric
shock:
Connect to properly grounded outlets only.
Keep extension cord connections dry and off the
ground.
Do not expose to rain.
Do not use indoors.
WARNING
If you smell gas:
1. Shut off gas to the grill.
2. Extinguish any open flames.
3. Open the top cover or lid.
4. If the odor continues, keep away from the
appliance and immediately call your gas
supplier or local fire department.
3
SAFETY INSTRUCTIONS
WARNING
Do not try lighting this appliance without first reading
the “LIGHTING INSTRUCTIONS” section of this
manual.
TESTED IN ACCORDANCE WITH ANSI Z21.582007a • CSA 1.6a-2007 STANDARD FOR
OUTDOOR COOKING GAS APPLIANCES. THIS
GRILL IS FOR OUTDOOR USE ONLY.
Check your local building codes for the proper
method of installation. In the absence of local codes,
with either the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, or CSA B149.1, Natural Gas and
propane Installation Code. Electrical Code,
ANSI/NFPA 70.
CALIFORNIA PROPOSITION 65-WARNING
The burning of gas fuel generates some byproducts, which are known by the State of California
to cause cancer or reproductive harm. To minimize
exposure to these substances, always operate this
unit according to the care and use manual, ensuring
you provide good ventilation when cooking with gas.
SAFETY PRACTICES TO AVOID INJURY
When properly cared for, your grill will provide safe,
reliable service for many years. However, extreme
care must be used as the grill produces intense heat
that can increase accident potential.
When using this appliance basic safety practices
must be followed, including the following:
Do not repair or replace any part of the grill unless
specifically recommended in this manual. All other
service should be referred to a qualified technician.
The grill is for outdoor use only.
The grill is not intended to be installed in or on
recreational vehicles and/or boats.
Children should not be left alone or unattended in an
area where the grill is being used. Do not allow
children to sit, stand or play on or around the grill at
any time.
Do not store items of interest to children around or
below the grill or cart. Do not allow children to crawl
inside the cart.
Never let clothing, pot holders or other flammable
materials come in contact with or too close to any
grate, burner or hot surface until it has cooled. The
fabric could ignite, causing serious personal injury.
For personal safety, wear proper apparel. Loose
fitting garments or sleeves should never be worn
while using this appliance. Some synthetic fabrics
are highly flammable and should not be worn while
cooking.
Only certain types of glass, ceramic, earthenware, or
other glazed utensils are suitable for grill use. Other
types of materials may shatter with sudden
temperature changes. Use only low or medium heat
settings in accordance with the manufacturer’s
guidelines.
Do not heat unopened food containers as a build-up
of pressure may cause the containers to burst.
Use a covered hand when opening the grill lid.
Never lean over an open grill.
When lighting a burner, always pay close attention
to what you are doing. Make certain you are aware
of which burner you are lighting so that your body
and clothing remain clear of open flames.
4
SAFETY INSTRUCTIONS
When using the grill, do not touch the grill rack,
burner grate or immediate surroundings as these
areas become extremely hot and could cause
burns. Use only dry potholders. Moist or damp
potholders on hot surfaces may cause steam burns.
Do not use a towel or bulky cloth in place of
potholders. Do not allow potholders to touch hot
portions of the grill rack.
Grease is flammable. Let hot grease cool before
attempting to handle it. Do not allow grease
deposits to collect in the grease tray at the bottom
of the grill’s firebox. Clean the grease tray often.
Do not use aluminum foil to line the grill racks or
grill bottom. This can severely upset combustion air
flow or trap excessive heat in the control area.
For proper lighting and performance of the burners,
keep the burner ports clean. It is necessary to clean
them periodically for optimum performance. The
burners will only operate in one position and must
be mounted correctly for safe operation.
Clean the grill with caution. To avoid steam burns,
do not use a wet sponge or cloth to clean the grill
while it is hot. Some cleaners produce noxious
fumes or can ignite if applied to a hot surface.
INSECT WARNING
Spiders and other insects can nest inside the
burners of this and other grills, which could disrupt
gas flow. This dangerous condition could cause a
fire behind and beneath the valve panel, damaging
the grill and making it unsafe for operation.
Inspect the grill at least twice a year.
Never use a dented or rusty propane cylinder.
PLACEMENT OF THE GRILL
CLEARANCE
Non-Combustible Construction
A minimum of 24 inches clearance from the back
of the grill to non-combustible materials are
required for the lid to open fully.
WARNING
Do not install this unit into combustible
enclosures. There should be a minimum
clearance of 24 inches from all sides to
combustible materials.
Turn off all control knobs and make certain the grill
is cool before using any type of aerosol cleaner on
or around it. The chemical that produces the
spraying action could, in the presence of heat,
ignite or cause metal parts to corrode.
Do not use the grill to cook excessively fatty meats
or other products, which promote flare-ups.
Do not operate the grill under unprotected
combustible constructions. Use only in wellventilated areas. Do not use in buildings, garages,
sheds, breezeways or other such enclosed areas.
This unit is intended for outdoor use only.
Keep the areas surrounding the grill free from
combustible materials including, fluids, trash, and
vapors such as gasoline or charcoal lighter fluid. Do
not obstruct the flow of combustion and ventilation
air. If the unit is stored indoors, make sure it is cool.
Do not use briquettes of any kind in the grill.
The 720-0512 liquid propane gas grill is designed
for optimum performance without the use of
briquettes. Do not place briquettes on the flame
tamers as this will block the vent to the grill burners.
Adding briquettes can damage ignition components,
thus voiding the warranty.
Keep the back of the cart free and clear from
debris. Keep electrical supply cords and the
rotisserie motor cord away from heated areas of the
grill.
Never use the grill in extremely windy conditions. If
located in a consistently windy area (oceanfront,
mountaintop, etc.), a windbreak will be required.
Always adhere to the clearance specifications.
LOCATION
When determining a suitable location take into
account concerns such as exposure to wind,
proximity to traffic paths, and keeping gas supply
lines as short as possible.
Place the grill in well-ventilated areas. Never place
the grill in a building, garage, breezeway, shed or
other such enclosed areas. During heavy use, the
grill will produce a lot of smoke.
5
SIDE SHELF ASSEMBLY
Estimated Assembly Time: Approximately 10 minutes
Required Tools: Phillips Screwdriver (not included)
1. Open the grill lid and remove the side shelf from the fire box.
2. The screws used to attach the side shelf are already screwed into the side of the grill cart. Remove
the screws from the side panel.
3. Align the holes on the left side shelf with the holes in the grill cart. Insert the screws and tighten.
Note: The top two screws insert from inside the fire box while the bottom two screws insert from
under the left side shelf.
Secure bottom two
screws from below the
side shelf.
Secure top two screws
from inside the fire box.
Secure bottom screw from
below the side shelf front
panel and side burner
control panel.
6
SIDE BURNER ASSEMBLY
1. Open the grill lid.
2. The screws used to attach the side burner are already screwed into the right side of the grill cart. Remove
the screws from the side panel.
3. Align the holes on the right side burner with the holes in the grill cart. Insert the screws and tighten.
4. Align the side burner holes, and tighten all four screws from underneath the side burne r.
Secure all four screws from
underneath the side burner.
7
SIDE BURNER HOSE QUICK DISCONNECT ASSEMBLY
Estimated Assembly Time: Approximately 5 minutes
No Tools Required
1. Insert the side burner hose with female sleeve through side panel of cart (A).
2. Push the sleeve of the female socket back and insert the male end of the connector. Release the
sleeve.
3. Push the male end into the socket until the sleeve snaps forward to lock the plug in place.
4. To disconnect, push the sleeve back and pull out the male end (B).
B
400300
500
600
200
100
700
800
WARNING
1. Attach the coupling half (socket) to the gas supply line in accordance with ANSI Z223.1/NFPA 54 FUEL gas
code.
2. Prior to inserting the plug, test the connection for leaks following the leak test instructions on page 15. After the
leak test is completed, rinse the connection with clean water to remove any corrosive residue.
3. Do not use open flame to test for leaks.
8
QUICK DISCONNECT ASSEMBLY
1. Install the quick disconnect by pulling the spring ring
downward on the female connector; insert the female
connector and release the spring ring (A).
2. After spring ring is released, male and female quick
disconnect will be locked together. Double check by
slightly pulling the hose connector upward, if not properly
connected, hose will be detached. Do not use excess
pulling force; doing so may cause manifold and/or burner
valve to become misaligned.
3. Make sure all the connections are tightly secured by
spraying a soapy solution (refer to “Leak Testing”
section).
9
SIDE SHELF HANDLE ASSEM BLY
Estimated Assembly Time: Approximately 5-7 minutes
Required Tools: Phillips Screwdriver (not included)
1. Remove the four side shelf handle screws from the side of the shelf.
2. Align the holes in the side shelf handle with the holes in the shelf.
3. Insert the screws and tighten.
500
400
600
300
700
800
200
100
BATTERY INSTALLATION
1. Unscrew the ignition button housing by turning counterclockwise.
2. Insert the battery into the housing with the positive (+) terminal facing outward.
3. Replace the ignition button housing after the battery has been installed.
500
600
400
300
700
800
200
100
10
Loading...