USER GUIDE
www.audiovias.com
VERSION 1.4
TechnoHaze performance
MARTIN MANUFACTURING (UK) PLC
MANUFACTURED BY
BELVOIR WAY,
FAIRFIELD INDUSTRIAL ESTATE,
LOUTH, LINCOLNSHIRE. LN11 0LQ.
TEL:(01507) 604399 FAX:(01507) 601956
Techno-Haze
‘Performance’
MARTIN MANUFACTURING (UK) PLC
TECHNO-HAZE USER GUIDE
www.audiovias.com
TECHNO-HAZE USER GUIDE
Fluids suitable for this machine:
Pro-Haze
How To Contact Us
Address:
Telephone:
Fax:
Email: jem@martin.dk
Website: Http://www.jemsmoke.com
Martin Manufacturing (uk) Plc
Belvoir Way,
Fairfield Industrial Estate,
Louth, Lincolnshire. LN11 0LQ.
+44 (0) 1507 604399
+44 (0) 1507 601956
/
Note:
The JEM warranty will be void if any fluid other then JEM approved fluid is used. If
other fluids are used there could be serious damage to the machine and the fluid
may not of been tested for use in public areas.
MARTIN MANUFACTURING (UK) PLC
MARTIN MANUFACTURING (UK) PLC
PAGE 9
TECHNO-HAZE USER GUIDE
www.audiovias.com
TECHNO-HAZE USER GUIDE
Trouble Shooting
Check main fuse.
Check power is connected.
Check fuse on Main PCB.
Check connection of remote control.
•
User Guide Index
•
Introduction
Safety
•
Machine Layout
•
Getting Started
•
Using The Remote Control
•
Trouble Shooting
•
How To Contact Us
•
Check fluid level LED.
Contact your Distributor.
Replenish fluid container.
CAUSE CURE
Main fuse blown..
No power connected.
Fuse on main PCB blown.
Remote control not connected.
Thermocouple fault
Thermal trip fault
SYMPTOM
The mains switch does not light
when I switch on.
The power LED does not light on
the remote control.
The ready LED does not light.
even after 15 minutes.
PAGE 8
MARTIN MANUFACTURING (UK) PLC
No fluid in container.
No haze output. Low fluid level.
Note:
Martin Manufacturing (UK) reserves the right to modify or change the
specification of this product without prior notice.
No part of this publication shall be copied without permission
© Martin Manufacturing (UK). 1999
MARTIN MANUFACTURING (UK) PLC
PAGE 1
TECHNO HAZE USER GUIDE
www.audiovias.com
TECHNO HAZE USER GUIDE
Introduction
The TECHNO-HAZE has been designed to produce a perfect translucent
environment for today’s intelligent lighting effects.
Furthermore, this unique design is guaranteed to give the user maximum
reliability thanks to features such as the “Low fluid cut off system”,which
protects the pump in the event of machine running out of fluid.
Creating the perfect ambient haze relies heavily on the correct particle size
and dispersion. The TECHNO-HAZE produces this by vapourising the special
working fluid at very precise temperature in a high mass heater block which
contains a cuperous helicoil of 3 metres length.
The product of this process is injected into the uniquely designed JEM
‘Expansion Chamber’ where it is mixed with a turbulent airflow and projected
from the machine as an optically translucent haze at 1200 ft / minute (exit
velocity).
The Techno-Haze uses a ‘Direct Thermal Protection Device’ to ensure maximum
overheat protection and therefore greater reliability.
the
Features
•
•
•
“DTP” Safety system
SMD electronics
Low fluid cut off system
Remote Control Functions
•
OUTPUT LEVEL CONTROL:
use the prime button as described on page 5 para 2. During normal opera-
tion, the output control should be set between 4 and 10.
give the output density you require.
Setting the level control to minimum will switch off the output
POWER LED: This indicates that the machine is powered and that the
•
remote is connected.
When starting the machine for the first time,
Use the control to
•
•
•
•
PAGE 2
Variable output remote
2.5 Litre fluid capacity
Expansion chamber
High power fan
MARTIN MANUFACTURING (UK) PLC
MARTIN MANUFACTURING (UK) PLC
PAGE 7
TECHNO HAZE USER GUIDE
www.audiovias.com
TECHNO HAZE USER GUIDE
Using The Remote Control
POWER
LED
ON
3
2
1
5
4
OUTPUT
PRIME
6
7
8
9
PRIME
BUTTON
Safety
•
Always use a JEM approved fluid, other fluids could be dangerous and could
cause damage to the machine.
Always check the voltage is correct for use with the machine, the voltage
•
setting is printed on the serial label.
Always read the user guide before operating the machine, smoke machines
•
need to be operated carefully to avoid risk.
Do not remove the cover or attempt to repair a faulty machine, an authorized
•
JEM dealer should be contacted in the event of a faulty machine.
Always use smoke machines in well ventilated areas, over use could affect
•
sufferers of asthma or other chest conditions.
Do not use the machine if there is a faulty mains lead or plug this could be
•
dangerous.
Do not spill fluid over the machine, if fluid is spilt clean with clean water and
•
contact an approved JEM dealer for advice.
Mains Lead Wiring Instructions
OUTPUT CONTROL
The Technohaze comes with a compact remote allowing the user to prime the pump
and control the output level.
PAGE 6
MARTIN MANUFACTURING (UK) PLC
Brown = Live
Blue = Neutral
Green/Yelllow = Earth
Note! This Appliance must be earthed
MARTIN MANUFACTURING (UK) PLC
PAGE 3
TECHNO HAZE USER GUIDE
www.audiovias.com
TECHNO HAZE USER GUIDE
Machine Layout
FLUID OUT
LED
READY LED
TOP VIEW
HEAT LED
FLUID
COMPARTMENT
Getting Started
•
Once you have selected the best position for the TECHNO- HAZE you can
begin to use the machine. First check the power supply you have is correct
for the machine .If it is, you can connect to the power supply and switch the
mains switch on at the rear of the machine; the machine will start to heat up
and the fan will run. It will take approximately 10 minutes for the machine to
reach working temperature. While it heats up you should check the level in
the fluid container; the container can hold up to 2.5 litres of fluid. The
machine may not heat if there is inadequate fluid in the container (the red
‘fluid out’ LED must not be on).
When the machine has reached working temperature the green “ready” LED
•
will light on the top of the machine and the machine can now be operated.
Press the prime button until haze appears from the output; the pump is now
primed. This will only have to be done if the fluid lines have become empty.
The output can now be set to the desired level by turning the “output” knob.
When you have finished using the machine you should turn the mains switch
•
off. If any problems occur when operating the TECHNO-HAZE please refer
to the trouble shooting guide.
REMOTE CONNECTION
MAINS SWITCH
REAR VIEW
PAGE 4
MARTIN MANUFACTURING (UK) PLC
FA N
POWER LEAD
MARTIN MANUFACTURING (UK) PLC
PAGE 5
Loading...