Jem HEAVY FOG GLACIATOR User Manual

Unit C6 Hastingwood Trading Estate

35 Harbet Road London N18 3HU

email: [e-mail]

Phone [phone]
FAX [phone]

HEAVY FOG GLACIATOR

HEAVY FOG GLACIATOR

Fluids Suitable for this system:

Heavy Fog
Fluid B2

Heavy Fog
Fluid C3

NOTE! The JEM warranty will be void if any fluid other than JEM
approved fluid is used. If other fluids are used there could be serious
damage to the machine and the fluid may not have been tested for use
in public areas.

CONNECTIONS

REMOTE

1-GND, 2-12V OUT, 3-INPUT

1

INTERFACE

569

DMX ADDRESS

1 GND
2 COLD
3 HOT

OUT

IN

ON

1 FOG
2 STANDBY
3 TIMER
4FAN
5 SPECIAL
6 GND

1

1

2

2

4

3

8

4

16

5

32

6

64

7
8

128

9

256

10

SPECIAL 1

11

SPECIAL 2

12

SPECIAL 3

INPUT

FUSE RATINGS

The Heavy Fog Glaciator uses
four fuses.
They should be replaced with
the value and type detailed
below:

DMX receiver low voltage

2AT

Power PCB

12AT

Compressor control relay

12AT

Main input fuse

20AT

Three of these fuses are
located internally and should
not be accessed without first
disconnecting the power supply.

FILTERS

The Heavy Fog Glaciator uses
a washable synthetic fibre filter
in the air intake for the
condenser unit (located at the
top of the machine). This can
be removed for cleaning by
removing the ventilation grill
above it (two M5 screws). Use

DMX DATA

the following guidelines for
when to check the filter.

Normal Conditions

:
Inspect and clean/replace every
250 hours

Severe Conditions

:
Inspect and clean/replace every
150 hours

17

HEAVY FOG GLACIATOR

USER
GUIDE

HEAVY FOG GLACIATOR

USER
GUIDE

SPECIFICATION

HEAT EXCHANGER

2.5KW heater (240V)
Wide bore steel vaporizing coil
Ceramic thermal trip for over-temperature protection
Electronic Temperature control using thermocouple

FLUID SYSTEM
Oscillating piston high pressure fluid pump
Low fluid detection by electronic sensor

9.5L fluid containers (2.5 US Gal.)
Maximum fluid consumption 120mL/minute

REMOTE CONTROL OPTIONS

DMX512 decoder:

Required Channels = 2
Output is proportional for all levels above 12%
Channels supported=1to511
Valid start codes = 0 (dimmer data only)

Full framing error detection implemented
Analogue control via standard JEM Multifunction Contoller.
Optional PLC interface for simple switching control of the system.

CONTROL PANEL

2 x LED displays with 4 button keypad
Output level control from 0 to 100% for Fog
Timer range:

Delay time (toF) 0 seconds - 90 seconds

Run time (ton) 0 seconds - 90 seconds

USER GUIDE CONTENTS

Introduction 2

Features 2

Safety Guidelines 3

Machine Layout 4

Commissioning The Machine 5

Remote Control Options 5

DMX Operation 6

The Display 8

Control Panel Functions 10

The Timer 11

Basic Operation 12

The Fluid System 13

Display Messages 14

Basic Fault Finding 15

REFRIGERATION UNIT
2/3 HP compressor with thermostatic control
Uses refrigerant R404A (0.850 Kg)

OUTPUT CONNECTION

Ducting adaptor to accept 150mm (6”) flexible ducting

POWER REQUIREMENTS

Input voltage 200 - 250vac
Input power (max) 3.1Kw
Main fuse 20AT
Frequency 50/60Hz dependant on model.

16

Specification 16

Connections 17

Fuse Ratings 17

Filter Maintenance 17

© Martin Professional A/S, Denmark.2000
All rights reserved. No part of this manual may be reproduced, in any form or

by any means, without permission in writing from Martin Professional A/S,
Denmark.

1