Jeep Wrangler 2008 User Manual

2008
OWNER’S MANUAL
Wrangler
SECTION PAGE
INTRODUCTION
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING YOUR INSTRUMENT PANEL
STARTING AND OPERATING
WHAT TO DO IN EMERGENCIES
MAINTAINING YOUR VEHICLE
MAINTENANCE SCHEDULES
IF YOU NEED CONSUMER ASSISTANCE
TABLE OF CONTENTS
.............................................................3
...............................9
...............................79
................................... 201
................................................. 267
...............................................363
............................................... 375
..................................................427
..........................................435
1
2
3
4
5
6
7
8
9
10
INDEX
....................................................................445
10
CONTENTS

INTRODUCTION

1
Introduction ........................... 4
Rollover Warning ........................ 5
How To Use This Manual ..................6
Warnings And Cautions ................... 8
Vehicle Identification Number ...............8
Vehicle Modifications/Alterations ............ 8
4 INTRODUCTION

INTRODUCTION

This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle.
The two-wheel drive utility vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle.
Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, transmis­sion, and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road or
working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive.
As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Refer to “On-Road/Off-Road Driving Tips” in Section 5 of this manual.
This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instruc­tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5
NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings.
When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine MOPARparts, and is inter­ested in your satisfaction.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower track than many passenger cars. It is capable of perform­ing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can be caused to go out of control. Because of the higher center of gravity and the narrower track, if this vehicle is out of control it may roll over when some other vehicles may not.
Operating this vehicle at excessive speeds or while intoxicated may result in loss of control, collision with other vehicles or objects, going off the road, or overturn­ing, any of which may lead to serious injury or death. Also, failure to use standard seat belts subjects the driver and passengers to a greater risk of being thrown out of an open-body vehicle than out of a closed vehicle in an accident which can result in injury or death.
Although your vehicle may be equipped with a soft top or optional hard top to give the occupants protection from the weather, these tops do not offer structural protection in the event of an accident and do not change the open-body characteristic of the vehicle. Even though your vehicle has a sport bar and side bars for some extra protection, it is a truly open vehicle-there is no structural integrated top and it has low sides and a folding wind­shield. Many of these vehicles do not have fully enclosed hard doors.
1
6 INTRODUCTION
Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, rollover of the vehicle and serious injury or death. Because of its open-body construction, your vehicle offers less protection than closed vehicles in the event of an accident.
Rollover Warning Label
Failure to use driver and passenger seat belts provided
is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seal belt. Always buckle up.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.
The detailed Index at the back of this manual contains a complete listing of all subjects.
Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual.
INTRODUCTION 7
1
8 INTRODUCTION

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce­dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
NOTE: It is illegal to remove the VIN plate.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!
Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS
A Word About Your Keys ..................12
Ignition Key Removal ...................12
Key-In-Ignition Reminder ................14
Steering Wheel Lock .....................14
To Manually Lock The Steering Wheel .......14
To Release The Steering Wheel Lock .........14
Sentry Key...........................14
Replacement Keys ......................16
Customer Key Programming ..............16
2
General Information ....................17
Security Alarm System — If Equipped .........18
To Set The Alarm ......................18
To Disarm The System ...................18
Illuminated Entry ........................19
Remote Keyless Entry — If Equipped .........19
To Unlock The Doors And Swing Gate .......20
To Lock The Doors And Swing Gate .........20
Using The Panic Alarm ..................21
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
To Turn Off “Flash Lights With Lock” ........21
Programming Additional Transmitters ........22
General Information ....................23
Battery Replacement ....................24
Remote Starting System — If Equipped ........25
Doors ................................26
Upper Half Door Window Removal
(If Equipped) .........................27
Upper Half Door Window Installation
(If Equipped) .........................27
Front Door Removal ....................28
Rear Door Removal (Four-Door Models) ......29
Door Locks ............................31
Manual Door Locks .....................32
Power Door Locks — If Equipped ..........33
Automatic Unlock Doors On Exit ...........34
Automatic Door Locks ...................35
Windows .............................36
Power Windows — If Equipped ............36
Rear Power Windows (Four-Door
Models Only) .........................37
Wind Buffeting ........................38
Rear Swing Gate ........................38
Occupant Restraints ......................40
Lap/Shoulder Belts .....................41
Rear Center Lap/Shoulder Belt Retractor
Lock-Out (Four-Door Models Only) .........46
Adjustable Upper Shoulder Belt Anchorage ....47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11
Seat Belt Pretensioners ...................48
Enhanced Seat Belt Use Reminder System
(BeltAlert) ..........................49
Seat Belts And Pregnant Women ............50
Seat Belt Extender ......................50
Driver And Front Passenger Supplemental
Restraint Systems (SRS) ..................51
Child Restraint ........................62
Engine Break-In Recommendations ...........75
Safety Tips ............................75
Exhaust Gas ..........................75
Safety Checks You Should Make Inside The
Vehicle ..............................76
Safety Checks You Should Make Outside The
Vehicle ..............................77
2
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your authorized dealer to give you the number. The key code can also be obtained by your authorized dealer from your vehicle invoice.

Ignition Key Removal

Manual Transmission — If Equipped
1. Turn the ignition switch to the ACCESSORY (ACC) position.
Ignition Key Positions
2. Push the ignition key inward.
3. Turn the ignition key to the LOCK position, and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
Automatic Transmission — If Equipped
1. Place the shift lever in the PARK position.
2. Turn the ignition switch to the ACC position.
Ignition Key Positions
3. Push the ignition key inward.
4. Turn the ignition key to the LOCK position, and remove the key.
WARNING!
Leaving unattended children in a vehicle is danger­ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
CAUTION!
An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended.
2
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Key-In-Ignition Reminder

Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key.

STEERING WHEEL LOCK

Your vehicle is equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is moved a half turn in either direction, and the key is not in the ignition, the steering wheel will lock.

To Manually Lock the Steering Wheel

With the engine running, rotate the steering wheel one– half revolution from the straight ahead position, turn off the engine, and remove the key. Rotate the steering wheel slightly in both directions until the lock engages.

To Release the Steering Wheel Lock

Insert the key in the ignition, and turn the wheel slightly to the left or right, to disengage the lock.
NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it.

SENTRY KEY

The Sentry KeyImmobilizer System prevents unautho­rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
The system uses ignition keys that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are pro­grammed to the vehicle can be used to start and operate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
the vehicle. The system will shut the engine off in two seconds if someone uses an invalid key to try to start the engine.
NOTE: A key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle.
During normal operation, after turning on the ignition switch, the Vehicle Security Alarm Indicator Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid key to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds.
If the Vehicle Security Alarm Indicator Light turns on during normal vehicle operation (vehicle running for
longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle ser­viced as soon as possible.
NOTE:
The Sentry KeyImmobilizer System is not compat­ible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
Exxon/Mobil Speedpass™, additional Sentry Keys, or any other transponder-equipped components on the same key chain will not cause a key-related (transponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system.
All of the keys provided with your new vehicle have been programmed to the vehicle electronics.
2
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Replacement Keys

NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Keyis programmed to a vehicle, it cannot be programmed to any other vehicle.
CAUTION!
Always remove the Sentry Keysfrom the vehicle and lock all doors when leaving the vehicle unattended.
At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Du­plication of keys may be performed at an authorized dealer or by following the customer key programming
procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed.
NOTE: When having the Sentry KeyImmobilizer System serviced, bring all vehicle keys with you to an authorized dealer.

Customer Key Programming

If you have two valid Sentry Keys, you can program new Sentry Keysto the system by performing the following procedure:
1. Cut the additional Sentry KeyTransponder blank(s) to match the ignition switch lock cylinder key code.
2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound. In addi­tion, the Vehicle Security Alarm Indicator Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.
4. Insert a blank Sentry Keyinto the ignition switch. Turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Alarm Indicator Light will stop flashing. To indicate that programming is complete, the Vehicle Security Alarm Indicator Light will turn on again for three seconds and then turn off.
The new Sentry Keyis programmed. The Remote
Keyless Entry (RKE) transmitter will also be pro­grammed during this procedure.
Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key, contact your authorized dealer for details.
NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys­tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be repro­grammed.

General Information

The Sentry Keysystem complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions:
This device may not cause harmful interference.
2
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
This device must accept any interference that may be received, including interference that may cause undes­ired operation.
SECURITY ALARM SYSTEM — IF EQUIPPED
This system monitors the vehicle doors, swing gate, and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visible signals. The horn, headlights, and tail lights will sound/ flash repeatedly for three minutes. If disturbance is still present (driver’s door, passenger door, other doors, igni­tion) after three minutes, the headlights and tail lights will flash for an additional 15 minutes.
NOTE: The Panic and Security alarms are quite differ­ent. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deactivate it.

To Set the Alarm

The alarm will set when you use the remote keyless entry (RKE) transmitter to lock the doors and swing gate, or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the Sentry Key/Security Alarm Indicator Light (located on the instrument cluster) will flash rapidly for about 16 seconds to signal that the system is arming. During this 16–second arming period, opening any door or the swing gate will cancel the arming. If the system successfully arms, the Sentry Key/Security Alarm Indicator Light will flash at a slower rate to indicate the alarm is set.

To Disarm the System

To disarm the system, you will need to press the UN­LOCK button on the RKE transmitter, or turn the ignition key to the ON position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tam­pering.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
The Security Alarm System is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the RKE transmitter, once the system is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, press the UNLOCK button on the RKE transmitter to disarm the system. You may also accidentally disarm the system by unlocking the driver’s door with the key and then locking it. The door will be locked but the Security Alarm will not arm.

ILLUMINATED ENTRY

The interior lights will come on when you open any door.
The lights will remain on after all of the doors are closed, and then fade to off or they will immediately fade to off once the ignition switch is turned on.
REMOTE KEYLESS ENTRY — IF EQUIPPED
2
Remote Keyless Entry (Key Fob)
This system allows you to lock or unlock the doors, swing gate, and activate the panic alarm from a maxi­mum distance of 66 ft (20 m) using a hand-held radio transmitter (key fob). The RKE transmitter does not need to be pointed at the vehicle to activate the system.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: The line of transmission must not be blocked with metal objects.

To Unlock the Doors and Swing Gate

Press and release the UNLOCK button once to unlock the driver’s door only, or twice to unlock all the doors and swing gate. When the UNLOCK button is pressed, the illuminated entry will initiate and the parking lights will flash twice.
The system can be programmed to unlock all the doors upon the first UNLOCK button press, using the follow­ing procedure:
1. Press and hold the LOCK button on a programmed key fob.
2. Continue to hold the LOCK button for at least four seconds, but not longer than 10 seconds, then press and hold the UNLOCK button.
3. Release both buttons at the same time.
4. Test this feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the key fob.
NOTE: Pressing the LOCK button while you are inside of the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.

To Lock the Doors and Swing Gate

Press and release the LOCK button on the key fob to lock all doors. The turn signals will flash and the horn will chirp once to acknowledge the lock signal. If desired, the “Sound Horn On Lock” feature can be turned on or off using the following steps:
1. Press the LOCK button for 4 to 10 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
2. While the LOCK button is pressed (after four seconds), press the PANIC button. Release both buttons.
The “Sound Horn On Lock” feature can be reactivated by repeating this procedure.

Using The Panic Alarm

To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the key fob for at least one second and release. When the panic alarm is activated, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.
The panic alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time, or if the vehicle speed is 5 mph (8 km/h) or greater.
NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system.
To Turn Off “Flash Lights With Lock”
NOTE: The “Flash Lights With Lock” feature can be turned on or off using the following steps:
1. Press the UNLOCK button for 4 to 10 seconds.
2. While the UNLOCK button is pressed, (after four seconds) press the LOCK button. Release both buttons.
3. Test the “Flash Lights With Lock” feature outside of the vehicle, by pressing the LOCK button with the ignition in the LOCK position, and the key removed.
NOTE: Pressing the LOCK button, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
The “Flash Lights With Lock” feature can be reactivated by repeating this procedure.
2
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Programming Additional Transmitters

Vehicles will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of eight key fobs can be programmed for your vehicle. Additional key fobs can be programmed to your vehicle through the use of a currently programmed fob.
NOTE: When entering the program mode using that key fob, all other programmed key fobs will be erased and you will have to reprogram them for your vehicle.
Use the following procedure to program additional key fobs if the vehicle is not equipped with a Sentry Key:
1. Enter the vehicle and close all of the doors.
2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure).
3. Place the ignition key into the ignition.
4. Turn the ignition to the ON position. Do not start the
engine.
5. Press and hold the UNLOCK button.
6. After holding the UNLOCK button for four seconds, also press the PANIC button within six seconds.
7. When a single chime is heard, release both buttons. The chime is an indication that you have successfully entered program mode. All key fobs that are to be programmed must be done so within 60 seconds of when the chime was heard.
8. Using the key fob to be programmed, press and release both the LOCK and UNLOCK buttons, simulta­neously.
9. A single chime will be heard.
10. Within four seconds of hearing the chime, press and release the UNLOCK button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
11. A single chime will be heard.
12. Repeat steps 8 through 10 to program up to six additional key fobs.
13. Turn the ignition to the OFF position.
14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed key fobs function normally.
NOTE: If you do not have a programmed RKE key fob, contact your authorized dealer for details.

General Information

This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly ap­proved by the party responsible for compliance could void the user’s authority to operate the equipment.
If your Remote Keyless Entry fails to operate from a normal distance, check for these two conditions.
1. Weak batteries in the RKE key fob. The expected life of batteries is five years.
2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios.
2
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Battery Replacement

The recommended replacement battery is CR2032.
NOTE: Perchlorate Material – special handling may apply; See www.dtsc.ca.gov/hazardouswaste/ perchlorate.
1. If the key fob is equipped with a screw, remove the screw. With the key fob buttons facing down, use a flat blade (screwdriver) to pry the two halves of the trans­mitter apart. Use extreme care not to damage the seal or internal components.
Separating RKE Key Fob Halves
2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.
3. To reassemble the key fob case, snap the two halves together.
NOTE: If the key fob is equipped with a screw, reinstall and tighten the screw until snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
REMOTE STARTING SYSTEM — IF EQUIPPED
Your vehicle may be equipped with a remote starting system (automatic transmission models only), which will allow the vehicle to be started from distances up to approximately 300 ft (91 m) away from the vehicle using the remote keyless entry key fob which is part of your ignition key.
In order to remote start your vehicle, the hood, swing gate, and all the doors must be closed.
To remote start your vehicle, press the “Remote Start” button on the key fob twice within five seconds. To indicate that the vehicle is about to start, the park lights will flash and the horn will sound briefly (if pro­grammed).
2
Remote Start Key Fob
Once the vehicle has started, the engine will run for 15 minutes. To cancel remote start, press the “Remote Start” button once.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The park lamps will remain illuminated to indicate that the vehicle has remote started and the engine is running. The lamps will turn off when the ignition is turned to RUN or the remote start is cancelled.
To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the UNLOCK button on the key fob. Then, prior to the end of the 15 minute cycle, insert the key into the ignition switch and turn the switch to the ON position, otherwise the engine will cancel remote start and automatically turn off.
Remote start will also cancel if any of the following occur:
If the engine stalls or RPM exceeds 2500
Any engine warning lamps come on
The hood is opened
The hazard switch is pressed
The transmission is moved out of PARK
The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the Security Alarm is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition and moving it to the RUN position, then back to LOCK.

DOORS

The vacuum fluorescent (VF) display located in the odometer area will display the word “door” as an indication of a door ajar or not completely closed. When the vehicle is not moving and the door is ajar or not completely closed, the VF display will show the word “door.”
If any other active warnings including “gATE”, “gAS­CAP”, “noFUSE”, “CHANgE OIL”, or “ESPOFF” are present, they will be shown in the VF display and will also continue to cycle. If the vehicle is moving, three single chimes will occur, one chime for each complete display cycle (three cycles total). After this, the display will continue to cycle only (no chimes).
If the trip/reset button is pressed while the VF warnings are being displayed, the VF display will revert back to only displaying the odometer/trip odometer mileage.

Upper Half Door Window Removal (If Equipped)

1. Grasp the half door window and pull up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
2
Upper Half Door Window

Upper Half Door Window Installation (If Equipped)

1. Grasp the half door window and line up pins into pockets in lower door.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
2. Push down to ensure the half door window is fully seated.

Front Door Removal

1. Remove the hinge pin screws from the upper and lower outside hinges (using a #T50 Torxhead driver).
2. Unplug the wiring harness connector under instru­ment panel.
1 — Harness Connector 2 — Body Hook 3 — Door/Harness Strap
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29
3. Unhook the door strap from the body hook. Be careful not to allow the door to swing fully open as the mirror may damage paint.
4. With the door open, lift the door to clear hinge pins from their hinges, and remove door.
To reinstall the door(s), perform the previous steps in the opposite order.

Rear Door Removal (Four-Door Models)

1. Remove the hinge pin screws from the upper and lower outside hinges (using a #T50 Torxhead driver).
2. Slide the front seat(s) fully forward.
2
Loading...
+ 436 hidden pages