Jeep TRACKHAWK User Manual

Page 1
2018
OWNER’S MANUAL
Grand Cherokee
Page 2
VEHICLES SOLD IN CANADA
With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore.
DRIVING AND ALCOHOL
Drunken driving is one of the most frequent causes of accidents.
Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non­drinking driver, call a cab, a friend, or use public trans­portation.
WARNING!
Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.
This manual illustrates and describes the operation of features and equipment that are either standard or op­tional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.
FCA US LLC reserves the right to make changes in design and specifications, and/or make additions to or improve­ments to its products without imposing any obligation upon itself to install them on products previously manu­factured.
Copyright © 2018 FCA US LLC
Page 3
SECTION PAGE
INTRODUCTION ...................................................................3
1
GRAPHICAL TABLE OF CONTENTS ......................................................7
2
GETTING TO KNOW YOUR VEHICLE ...................................................13
3
GETTING TO KNOW YOUR INSTRUMENT PANEL .........................................117
4
SAFETY ........................................................................151
5
TABLE OF CONTENTS
1 2 3 4 5
STARTINGANDOPERATING.........................................................235
6
INCASEOFEMERGENCY ...........................................................351
7
SERVICING AND MAINTENANCE .....................................................389
8
TECHNICAL SPECIFICATIONS ........................................................457
9
MULTIMEDIA ....................................................................469
10
CUSTOMER ASSISTANCE ............................................................551
11
INDEX..........................................................................557
12
6 7 8 9 10
11
12
Page 4
Page 5

INTRODUCTION

CONTENTS
INTRODUCTION .........................4
1
ROLLOVER WARNING .....................5
HOW TO USE THIS MANUAL ...............5
Essential Information ......................5
Symbols ...............................5
WARNINGS AND CAUTIONS ................6
VEHICLE MODIFICATIONS/ALTERATIONS .....6
Page 6
4 INTRODUCTION

INTRODUCTION

Dear Customer, congratulations on selecting your new vehicle. Be assured that it represents precision workman­ship, distinctive styling, and high quality.
This is a specialized utility vehicle. It can go places and perform tasks that are not intended for conventional pas­senger vehicles. It handles and maneuvers differently from many passenger vehicles both on-road and off-road, so take time to become familiar with your vehicle. If equipped, the two-wheel drive version of this vehicle was designed for on-road use only. It is not intended for off-road driving or use in other severe conditions suited for a four-wheel drive vehicle. Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for brak­ing, steering, transmission, and transfer case shifting. Learn how your vehicle handles on different road surfaces. Your driving skills will improve with experience. When driving off-road, or working the vehicle, don’t overload the vehicle or expect the vehicle to overcome the natural laws of physics. Always observe federal, state, provincial and local laws wherever you drive. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a collision. Refer to the “Driving Tips” in “Starting and Operating” for further information.
This Owner’s Manual has been prepared with the assis­tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and customer oriented documents. In the attached Warranty Booklet you will find a description of the services that FCA offers to its customers, the Warranty Certificate and the details of the terms and conditions for maintaining its validity. Please take the time to read all of these publications carefully before driving your vehicle for the first time. Following the instructions, recommendations, tips, and important warn­ings in this manual will help assure safe and enjoyable operation of your vehicle.
This Owner’s Manual describes all versions of this vehicle. Options and equipment dedicated to specific markets or versions are not expressly indicated in the text. Therefore, you should only consider the information which is related to the trim level, engine, and version that you have purchased. Any content introduced throughout the Own­er’s Information, that may or may not be applicable to your vehicle, will be identified with the wording “If Equipped”. All data contained in this publication are intended to help you use your vehicle in the best possible way. FCA aims at a constant improvement of the vehicles produced. For this reason, it reserves the right to make changes to the model
Page 7
described for technical and/or commercial reasons. For further information, contact an authorized dealer.
If applicable, refer to the Owner’s Manual Supplement for related information.
NOTE: After reviewing the Owner’s Information, it should be stored in the vehicle for convenient referencing, and remain with the vehicle when sold.
When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techni­cians and genuine MOPAR® parts, and cares about your satisfaction.
HOW TO USE THIS MANUAL Essential Information
Consult the Table of Contents to determine which section contains the information you desire.
Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustra­tions may differ from your vehicle’s equipment.
The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
INTRODUCTION 5

Symbols

Some vehicle components have colored labels whose sym­bols indicate precautions to be observed when using this component. Refer to “Warning Lights and Messages” in “Getting To Know Your Instrument Panel” for further information on the symbols used in your vehicle.

ROLLOVER WARNING

Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications. Driven in an unsafe manner, all vehicles can go out of control. Because of the higher center of gravity, if this vehicle is out of control it may roll over while some other vehicles may not.
Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle con­trol. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully.
1
Page 8
6 INTRODUCTION
Rollover Warning Label
Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information. Observe all Warnings and Cau­tions.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!
Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
Page 9

GRAPHICAL TABLE OF CONTENTS

CONTENTS
FRONT VIEW ............................8
2
INSTRUMENT PANEL .....................10
REAR VIEW .............................9
INTERIOR ..............................11
Page 10
8 GRAPHICAL TABLE OF CONTENTS

FRONT VIEW

Front View
1 — Hood/Engine Compartment 4 — Wheels/Tires 2 — Windshield 5 — Exterior Mirrors 3 — Headlights 6 — Exterior Door Handle
Page 11

REAR VIEW

1 — Taillight 2 — Rear Windshield Wiper 3 — Liftgate
GRAPHICAL TABLE OF CONTENTS 9
2
Rear View
Page 12
10 GRAPHICAL TABLE OF CONTENTS

INSTRUMENT PANEL

Instrument Panel
1 — Air Vents 4 — Instrument Cluster 2 — Paddle Shifter (-) 5 — Paddle Shifter (+) 3 — Steering Wheel 6 — Glove Compartment
Page 13

INTERIOR

Interior Features
1 — Power Window Switches 4 — Switch Panel 2 — Seats 5 — Climate Controls 3 — Transmission Gear Selector 6 — Radio
GRAPHICAL TABLE OF CONTENTS 11
2
Page 14
Page 15

GETTING TO KNOW YOUR VEHICLE

CONTENTS
KEYS .................................17
KeyFob..............................17
IGNITION SWITCH .......................22
Keyless Enter-N-Go — Ignition ..............22
Vehicle On Message .....................24
REMOTE STARTING SYSTEM — IF EQUIPPED . . .25
How To Use Remote Start..................25
Remote Start Abort Message ................26
To Enter Remote Start Mode ................27
To Exit Remote Start Mode Without Driving The
Vehicle ...............................27
To Exit Remote Start Mode And Drive The
Vehicle ...............................27
Remote Start Comfort Systems — If Equipped . . .27
General Information .....................28
SENTRY KEY ............................28
3
Customer Key Programming ...............29
Replacement Keys .......................29
Irregular Operation ......................29
General Information .....................30
VEHICLE SECURITY ALARM — IF EQUIPPED . . .30
To Arm The System .....................31
To Disarm The System ...................31
Rearming Of The System ..................32
Security System Manual Override ............32
Tamper Alert ...........................32
DOORS ...............................32
Manual Door Locks ......................32
Power Door Locks ......................33
Page 16
14 GETTING TO KNOW YOUR VEHICLE
Keyless Enter-N-Go — Passive Entry .........34
Power Tilt/Telescoping Steering Column .......55
Automatic Unlock Doors On Exit ............38
Child-Protection Door Lock System —
Rear Doors ............................38
SEATS ................................39
Power Adjustment (Front Seats) .............40
Manual Adjustment (Rear Seats) ............42
Driver Memory Seat — If Equipped ..........42
Heated Seats — If Equipped ...............45
Front Ventilated Seats — If Equipped .........48
To Lower Rear Seat ......................49
To Raise Rear Seat .......................50
HEAD RESTRAINTS ......................50
Supplemental Active Head Restraints — Front
Seats.................................51
Adjustment — Rear Seats ..................53
Head Restraint Removal — Rear Seats .........54
STEERING WHEEL .......................55
Heated Steering Wheel — If Equipped ........56
MIRRORS ..............................57
Automatic Dimming Mirror ................57
Outside Mirrors ........................57
Outside Automatic Dimming Mirrors — If
Equipped .............................58
Power Mirrors .........................58
Power Folding Outside Mirrors — If Equipped. . .59
Heated Mirrors — If Equipped .............60
Tilt Side Mirrors In Reverse (Available With
Memory Seat Only) — If Equipped ...........60
Illuminated Vanity Mirrors ................61
EXTERIOR LIGHTS .......................61
Headlight Switch .......................61
Multifunction Lever .....................62
Daytime Running Lights — If Equipped .......62
High/Low Beam Switch ...................63
Page 17
Automatic High Beam — If Equipped ........63
GETTING TO KNOW YOUR VEHICLE 15
Rain Sensing Wipers — If Equipped ..........72
Flash-To-Pass ..........................63
Automatic Headlights — If Equipped .........64
Parking Lights And Panel Lights.............64
Headlights On Automatically With Wipers .....64
Headlight Delay ........................64
Lights-On Reminder......................65
Fog Lights — If Equipped .................65
Turn Signals ...........................65
Lane Change Assist — If Equipped ..........66
Automatic Headlight Leveling — HID Headlights
Only.................................66
Battery Saver ...........................66
INTERIOR LIGHTS........................66
Courtesy Lights .........................67
WINDSHIELD WIPERS AND WASHERS ........69
Windshield Wiper Operation................70
Rear Window Wiper/Washer ...............73
HEADLIGHT WASHERS — IF EQUIPPED ......74
CLIMATE CONTROLS .....................75
Automatic Climate Controls Overview ........75
Climate Control Functions .................79
Automatic Temperature Control (ATC) — If
Equipped .............................80
Operating Tips .........................81
WINDOWS .............................83
Power Window Controls ..................83
Auto-Down Feature .....................84
Auto-Up Feature With Anti-Pinch Protection ....84
Reset Auto-Up..........................85
Window Lockout Switch...................85
Wind Buffeting .........................85
COMMANDVIEW SUNROOF WITH POWER
SHADE — IF EQUIPPED ...................86
3
Page 18
16 GETTING TO KNOW YOUR VEHICLE
Opening Sunroof ........................87
GARAGE DOOR OPENER — IF EQUIPPED .....97
Closing Sunroof.........................87
Wind Buffeting .........................87
Opening Power Shade ....................88
Closing Power Shade .....................88
Pinch Protect Feature .....................89
Venting Sunroof — Express.................89
Sunroof Maintenance .....................89
HOOD ................................89
To Open The Hood ......................89
To Close The Hood ......................90
LIFTGATE .............................90
Opening .............................90
Closing ..............................92
Power Liftgate — If Equipped ..............92
Cargo Area Features .....................94
Before You Begin Programming HomeLink .....98
Canadian/Gate Operator Programming .......101
Using HomeLink .......................102
Security..............................102
Troubleshooting Tips ....................102
General Information .....................103
INTERNAL EQUIPMENT ..................104
Storage ..............................104
Cupholders ..........................108
Electrical Power Outlets ..................108
Power Inverter — If Equipped .............112
Sunglasses Bin Door ....................114
ROOF LUGGAGE RACK — IF EQUIPPED ......114
Page 19
KEYS Key Fob
Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system. The Remote Keyless Entry system consists of a key fob and Keyless Enter-N-Go feature if equipped.
NOTE: The key fob may not be found if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal.
The key fob allows you to lock or unlock the doors and liftgate from distances up to approximately 66 ft (20 m) using a handheld key fob. The key fob does not need to be pointed at the vehicle to activate the system.
GETTING TO KNOW YOUR VEHICLE 17
NOTE:
In the ON/RUN position, the lock button is disabled. Only the unlock button is enabled.
With ignition on/start and the vehicle moving at 5 mph (8 km/h), all RKE commands are disabled.

Key Fob

3
Page 20
18 GETTING TO KNOW YOUR VEHICLE
Key Fob With Emergency Key
NOTE: In case the ignition switch does not change with the
push of a button, the key fob may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side of the key fob (side opposite of the Emergency Key) against the ENGINE START/STOP button and push to operate the ignition switch.
To Unlock The Doors And Liftgate
Push the interior door unlock button on the door panel.
Push and release the unlock button on the key fob once to unlock the driver’s door or twice within five seconds to unlock all doors and the liftgate.
All doors can be programmed to unlock on the first push of the unlock button. Refer to “Uconnect Settings” in “Multi­media” for further information.
NOTE: If the vehicle is unlocked by key fob, and no door is opened within 60 seconds, the vehicle will re-lock and if equipped, the security alarm will arm. To change the current setting, refer to Uconnect Settingsin Multimedia for further information.
The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will be activated.
1st Push Of Key Fob Unlock Button
This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the unlock button on the key fob. To change the current setting, refer to “Uconnect Settings” in “Multimedia” for further information.
NOTE: If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go — Passive Entry” located in “Doors” in “Getting To Know Your Vehicle” for further information.
Page 21
To Lock The Doors And Liftgate
Push and release the lock button on the key fob to lock all doors and liftgate.
The turn signal lights will flash and the horn will chirp to acknowledge the signal. Refer to “Uconnect Settings” located in “Multimedia” for further programmable infor­mation.
If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go — Passive Entry” located in “Doors” in “Getting To Know Your Vehicle” for further information.
If one or more doors are open, or the liftgate is open, the doors will lock. The doors will unlock again automatically if the key is left inside the passenger compartment, other­wise the doors will stay locked.
Replacing The Battery In The Key With Remote Control
The recommended replacement battery is one CR2032 battery.
GETTING TO KNOW YOUR VEHICLE 19
NOTE:
Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for fur­ther information.
Do not touch the battery terminals that are on the back housing or the printed circuit board.
1.
Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways with your thumb and pull the emergency key out with your other hand.
Emergency Key Removal
1 — Emergency Key Release Button 2 — Emergency Key
3
Page 22
20 GETTING TO KNOW YOUR VEHICLE
2. Separate the key fob halves using the tip of the emer­gency key, a #2 flat blade screwdriver, or a coin and gently pry the two halves of the key fob apart. Make sure not to damage the seal during removal.
Emergency Key Removal
Separating Case With A Coin
Page 23
GETTING TO KNOW YOUR VEHICLE 21
Programming Additional Key Fobs
Programming the key fob may be performed by an autho­rized dealer.
Key Fob Battery Replacement
3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.
4. To assemble the key fob case, snap the two halves together.
Request For Additional Key Fobs
NOTE: Only key fobs that are programmed to the vehicle
electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.
WARNING!
Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended.
Always remember to place the ignition in the OFF mode.
Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed.
3
Page 24
22 GETTING TO KNOW YOUR VEHICLE
NOTE:
When having the Sentry Key Immobilizer System ser­viced, bring all vehicle keys with you to an authorized dealer.
Keys must be ordered to the correct key cut to match the vehicle locks.
NOTE: Black keys (6.4L) must be replaced with black keys and Red Keys (6.2L) must be replaced with Red Keys.
General Information
The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, in-
cluding interference that may cause undesired opera­tion.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IGNITION SWITCH Keyless Enter-N-Go — Ignition
This feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment.
The Keyless Push Button Ignition has several operating modes that are labeled and will illuminate when in posi­tion. These modes are OFF, ACC, RUN, and START.
NOTE: If the ignition switch does not change with the push of a button, the key fob may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the key fob against the ENGINE START/STOP button and push to operate the ignition switch.
Page 25
START/STOP Ignition Button
The push button ignition can be placed in the following modes:
OFF
The engine is stopped.
Some electrical devices (e.g. Central locking, alarm, etc.)
are still available.
ACC
Engine is not started.
Some electrical devices are available.
GETTING TO KNOW YOUR VEHICLE 23
RUN
Driving position.
All the electrical devices are available.
START
The engine will start.
WARNING!
When exiting the vehicle, always remove the key fob from the vehicle and lock your vehicle.
Never leave children alone in a vehicle, or with access to an unlocked vehicle.
Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.
Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter­N-Go in the ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
(Continued)
3
Page 26
24 GETTING TO KNOW YOUR VEHICLE
WARNING! (Continued)
Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
CAUTION!
An unlocked vehicle is an invitation for thieves. Al­ways remove key fob from the vehicle and lock all doors when leaving the vehicle unattended.
NOTE: Refer to Starting The Engine,in Starting And
Operatingfor further information.

Vehicle On Message

When opening the driver’s door when the ignition is in RUN (engine not running), a chime will sound to remind you to place the ignition in the OFF position. In addition to the chime, the message will display “Ignition Or Accessory On” in the cluster.
NOTE: The power window switches and power sunroof (if equipped) will remain active up to ten minutes after the ignition is cycled to the OFF position. Opening either front door will cancel this feature. The time for this feature is programmable.
WARNING!
Before exiting a vehicle, always come to a complete stop, then shift the automatic transmission into PARK, apply the parking brake, place the engine in the OFF position, remove the key fob from the vehicle and lock your vehicle. If equipped with Keyless Enter-N-Go, always make sure the keyless ignition is in “OFF” position, remove the key fob from the vehicle and lock the vehicle.
Never leave children alone in a vehicle, or with access to an unlocked vehicle.
Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.
Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter­N-Go in the ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
Page 27
CAUTION!
An unlocked vehicle is an invitation for thieves. Al­ways remove key fob from the vehicle and lock all doors when leaving the vehicle unattended.

REMOTE STARTING SYSTEM — IF EQUIPPED

GETTING TO KNOW YOUR VEHICLE 25
NOTE:
The vehicle must be equipped with an automatic trans­mission to be equipped with Remote Start.
Obstructions between the vehicle and key fob may reduce this range.
WARNING!
3
This system uses the key fob to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of 328 ft (100 m).
The Remote Starting System also activates the Climate Control, vented seats (if equipped) in temperatures above 80° F (26.7° C), and the optional heated seats, and optional heated steering wheel in temperatures below 40° F (4.4° C). Refer to “Seats” in “Getting To Know Your Vehicle” for further information.
Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monox­ide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled.
Keep key fobs away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.

How To Use Remote Start

Push Remote Start button on the key fob twice within five seconds. Pushing the Remote Start button a third time shuts the engine off.
With remote start, the engine will only run for 15 minutes (time out) unless the ignition is placed in the ON/RUN position.
Page 28
26 GETTING TO KNOW YOUR VEHICLE
The vehicle must be manually started with a push of the ignition START/STOP button after two consecutive time outs.
All of the following conditions must be met before the engine will remote start:
Gear Selector in PARK
Doors closed
Hood closed
Liftgate closed
Hazard switch off
Brake switch inactive (brake pedal not pushed)
Battery at an acceptable charge level
PANIC button not pushed
System not disabled from previous remote start event
Vehicle alarm system indicator flashing
Ignition in STOP/OFF position
Fuel level meets minimum requirement
WARNING!
Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monox­ide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled.
Keep key fobs away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.

Remote Start Abort Message

The following messages will display in the instrument cluster display if the vehicle fails to remote start or exits remote start prematurely:
Remote Start Cancelled — Door Open
Remote Start Cancelled — Hood Open
Remote Start Cancelled — Fuel Low
Remote Start Aborted Timer Expired
Remote Start Aborted Liftgate Open
Remote Start Disabled — Start Vehicle To Reset
Page 29
The instrument cluster display message stays active until the ignition is turned to the ON/RUN position.

To Enter Remote Start Mode

Push and release the Remote Start button on the key fob twice within five seconds. The vehicle doors will lock, the turn signals will flash twice, and the horn will chirp twice. Then the engine will start, and the vehicle will remain in the Remote Start mode for a 15-minute cycle.
GETTING TO KNOW YOUR VEHICLE 27

To Exit Remote Start Mode Without Driving The Vehicle

Push and release the Remote Start button one time or allow the remote start cycle to complete the entire 15-minute cycle.
NOTE: To avoid unintentional shutdowns, the system will disable the one time push of the Remote Start button for two seconds after receiving a valid Remote Start request.
3
NOTE:
If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.
The park lamps will turn on and remain on during Remote Start mode.
For security, power window operation is disabled when the vehicle is in the Remote Start mode.
The engine can be started two consecutive times (two 15-minute cycles) with the key fob. However, the igni­tion must be placed in the ON/RUN position before you can repeat the start sequence for a third cycle.

To Exit Remote Start Mode And Drive The Vehicle

Before the end of 15-minute cycle, push and release the unlock button on the key fob to unlock the doors, or unlock the vehicle using Keyless Enter-N-Go — Passive Entry via the door handles, and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15-minute cycle, push and release the START/STOP button.
NOTE: For vehicles equipped with the Keyless Enter­N-Go — Passive Entry feature, the message “Remote Start Active — Push Start Button” will display in the instrument cluster display until you push the ignition START button.

Remote Start Comfort Systems — If Equipped

When remote start is activated, the heated steering wheel and driver heated seat features will automatically turn on
Page 30
28 GETTING TO KNOW YOUR VEHICLE
in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the ignition switch is cycled to the ON/RUN position.
NOTE: The Auto Comfort System can be activated and deactivated through the Uconnect system. For more infor­mation on Comfort System operation, refer to “Uconnect Settings” in “Multimedia” for further information.

General Information

The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, in-
cluding interference that may cause undesired opera­tion.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

SENTRY KEY

The Sentry Key Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
The system uses a key fob, keyless push button ignition and a RF receiver to prevent unauthorized vehicle opera­tion. Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank if an invalid key fob is used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid key fob is used to start the engine.
After turning the ignition switch to the ON/RUN position, the vehicle security light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid key fob to start the engine. Either of these conditions will result in the engine being shut off after two seconds.
If the vehicle security light turns on during normal vehicle operation (vehicle running for longer than ten seconds), it indicates that there is a fault in the electronics. Should this
Page 31
occur, have the vehicle serviced as soon as possible by your authorized dealer.
CAUTION!
The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics.

Customer Key Programming

Programming key fobs may be performed at your autho­rized dealer.

Replacement Keys

NOTE: Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.
GETTING TO KNOW YOUR VEHICLE 29
CAUTION!
Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended.
For vehicles equipped with Keyless Enter-N-Go — Ignition, always remember to place the ignition in the OFF position.
NOTE: Duplication of key fobs may be performed at an
authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed.
When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.

Irregular Operation

The system uses a key fob, an Ignition Node Module, Keyless Push Button Ignition and a RF receiver to prevent unauthorized vehicle operation. Therefore, only key fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank if an invalid key fob is used to start and operate the vehicle. The system will shut the engine off in two seconds if an invalid key fob is used to start the engine.
3
Page 32
30 GETTING TO KNOW YOUR VEHICLE
NOTE: A key fob that has not been programmed is also considered an invalid key.
During normal operation, after placing the keyless ignition in the ON/RUN mode, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid key fob to try to start the engine. Either of these conditions will result in the engine being shut off after two seconds.
If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer.

General Information

The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
2. This device must accept any interference received, in­cluding interference that may cause undesired opera­tion.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

VEHICLE SECURITY ALARM — IF EQUIPPED

The vehicle security alarm monitors the vehicle doors, hood, liftgate, and the Keyless Enter-N-Go — Ignition for unauthorized operation. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled. If something triggers the alarm, the vehicle security alarm will provide the following audible and visible signals:
The horn will pulse.
The turn signals will flash.
The vehicle security light in the instrument cluster will
flash.
1. This device may not cause harmful interference, and
Page 33

To Arm The System

Follow these steps to arm the vehicle security alarm:
1. Make sure the vehicle’s ignition is placed in the “OFF” mode.
For vehicles equipped with Keyless Entry, make sure the vehicle’s keyless ignition system is OFF.
2. Perform one of the following methods to lock the vehicle:
Push the lock button on the interior power door lock switch with the driver and/or passenger door open.
Push the lock button on the exterior Passive Entry Door Handle with a valid key fob available in the same exterior zone (refer to Doorsin Getting To Know Your Vehiclefor further information).
Push the lock button on the key fob.
3. If any doors are open, close them.

To Disarm The System

The vehicle security alarm can be disarmed using any of the following methods:
Push the unlock button on the key fob.
GETTING TO KNOW YOUR VEHICLE 31
Grasp the passive entry door handle to unlock the door,
refer to Doorsin Getting To Know Your Vehiclefor further information.
Cycle the ignition out of the off mode to disarm the system.
NOTE:
The driver’s door key cylinder and the liftgate button on the key fob cannot arm or disarm the vehicle security alarm.
The vehicle security alarm remains armed during power liftgate entry. Pushing the liftgate button will not disarm the vehicle security alarm. If someone enters the vehicle through the liftgate and opens any door, the alarm will sound.
When the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors.
The vehicle security alarm is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the vehicle security alarm will arm, regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the vehicle security alarm.
3
Page 34
32 GETTING TO KNOW YOUR VEHICLE
If the vehicle security alarm is armed and the battery becomes disconnected, the vehicle security alarm will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound. If this occurs, disarm the vehicle security alarm.

Rearming Of The System

If something triggers the alarm, and no action is taken to disarm it, the vehicle security alarm will turn the horn off after 29 seconds, five seconds between cycles, up to eight cycles if the trigger remains active and the vehicle security alarm will rearm itself.
DOORS Manual Door Locks
The power door locks can be manually locked from inside the vehicle by using the door lock knob. To lock each door, push the door lock knob on each door trim panel down­ward. To unlock the front doors, pull the inside door handle to the first detent. To unlock the rear doors, pull the door lock knob on the door trim panel upward. If the lock knob is down when the door is closed, the door will lock. Therefore, make sure the key fob is not inside the vehicle before closing the door.

Security System Manual Override

The vehicle security alarm will not arm if you lock the doors using the manual door lock plunger.

Tamper Alert

If something has triggered the vehicle security alarm in your absence, the horn will sound three times and the exterior lights will blink three times when you disarm the vehicle security alarm. Check the vehicle for tampering.
NOTE: Manually locking the vehicle will not arm the vehicle security alarm.
WARNING!
For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle.
When exiting the vehicle, always make sure the keyless ignition node is in the OFF mode, remove the key fob from the vehicle and lock your vehicle.
(Continued)
Page 35
WARNING! (Continued)
Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.
Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter­N-Go in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.

Power Door Locks

The power door lock switches are located on each front door panel. Push the switch to lock or unlock the doors.
GETTING TO KNOW YOUR VEHICLE 33
3
Power Door Lock Switch
The driver’s door will unlock automatically if the keys are found inside the car when door lock button on trim is used to lock the door.
NOTE: If the key fob is located next to a mobile phone, laptop, or other electronic device, the wireless signal may get blocked, and the driver’s door may not unlock auto­matically.
At the third attempt, the doors will lock even if the key is inside.
Page 36
34 GETTING TO KNOW YOUR VEHICLE
If the door lock switch is pushed while the ignition is in ACC or ON/RUN and the driver’s door is open, the doors will not lock.
If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be unlocked manually by raising the lock knob.

Keyless Enter-N-Go — Passive Entry

The Passive Entry system is an enhancement to the vehi­cle’s key fob and a feature of Keyless Enter-N-Go — Passive Entry. This feature allows you to lock and unlock the vehicle’s door(s) and fuel door without having to push the key fob lock or unlock buttons.
NOTE:
Passive Entry may be programmed ON/OFF; refer to “Uconnect Settings” in “Multimedia” for further infor­mation.
The key fob may not be able to be detected by the vehicle passive entry system if it is located next to a mobile phone, laptop, or other electronic device; these devices may block the key fob’s wireless signal and prevent the passive entry system from locking/unlocking the ve­hicle.
Passive Entry Unlock initiates illuminated approach (Low Beams, License Plate Lamp, Position Lamps) for whichever time duration is set between 0, 30 (default), 60 or 90 seconds. Passive Entry Unlock also initiates two flashes of the turn signal lamps.
If wearing gloves on your hands, or if it has been raining/snowing on the Passive Entry door handle, the unlock sensitivity can be affected, resulting in a slower response time.
If the vehicle is unlocked by Passive Entry and no door is opened within 60 seconds, the vehicle will re-lock and if equipped will arm the security alarm.
To Unlock From The Driver Side
With a valid Passive Entry key fob within 5 ft (1.5 m) of the driver’s door handle, grab the front driver door handle to unlock the driver’s door automatically.
Page 37
Grab The Door Handle To Unlock
NOTE: If “Unlock All Doors 1st Press” is programmed all
doors will unlock when you grab hold of the front driver’s door handle. To select between “Unlock Driver Door 1st Push” and “Unlock All Doors 1st Press,” refer to “Uconnect Settings” in “Multimedia” for further information.
To Unlock From The Passenger Side
With a valid Passive Entry key fob within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors and the liftgate automati­cally.
GETTING TO KNOW YOUR VEHICLE 35
NOTE: All doors will unlock when the front passenger door handle is grabbed regardless of the driver’s door unlock preference setting (“Unlock Driver Door 1st Press” or “Unlock All Doors 1st Press”).
Preventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle (FOBIK-Safe)
To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature which will function if the ignition switch is in the OFF position.
FOBIK-Safe only executes in vehicles with passive entry. There are five situations that trigger a FOBIK-Safe search in any passive entry vehicle:
A lock request is made by a valid Passive Entry key fob while a door is open.
A lock request is made by the Passive Entry door handle while a door is open.
A lock request is made by the door panel switch while the door is open.
When the vehicle security alarm is in pre-arm or armed status and the liftgate transitions from open to closed.
3
Page 38
36 GETTING TO KNOW YOUR VEHICLE
When the liftgate transitions from opened to closed and remote start is active.
When any of these situations occur, after all open doors are shut, the FOBIK-Safe search will be executed. If it finds a Passive Entry key fob inside the car, the car will unlock and alert the customer.
NOTE: The vehicle will only unlock the doors when a valid Passive Entry key fob is detected inside the vehicle. The vehicle will not unlock the doors when any of the follow­ing conditions are true:
The doors are manually locked using the door lock knobs.
Three attempts are made to lock the doors using the door panel switch and then close the doors.
There is a valid Passive Entry key fob outside the vehicle within 5 ft. (1.5 m) of a Passive Entry door handle.
If the keys are left in the vehicle while the liftgate is opened, and all four doors are then locked, closing the liftgate will lock the keys within the vehicle.
To Lock The Vehicle’s Doors And Liftgate
With one of the vehicle’s Passive Entry key fob within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the passive entry lock button will lock the vehicle.
Push The Door Handle Button To Lock
NOTE: DO NOT grab the door handle, when pushing the
door handle lock button. This could unlock the door(s).
Page 39
DO NOT Grab The Door Handle When Locking
NOTE:
After pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle without the vehicle reacting and unlocking.
If Passive Entry is disabled using Uconnect System, the key protection described in Preventing Inadvertent Locking of Passive Entry Key Fob in Vehicleremains active/functional.
The Passive Entry system will not operate if the key fob battery is dead.
GETTING TO KNOW YOUR VEHICLE 37
The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel.
To Unlock/Enter The Liftgate
The liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the electronic liftgate release to open with one fluid motion.
Electronic Liftgate Release/Liftgate Passive Entry Location
1 — Electronic Liftgate Release 2 — Lock Button Location
3
Page 40
38 GETTING TO KNOW YOUR VEHICLE
To Lock The Liftgate
With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the passive entry lock button located on the outside liftgate door handle.
NOTE: The liftgate passive entry lock button will lock all doors and the liftgate. The liftgate unlock feature is built into the electronic liftgate release.

Automatic Unlock Doors On Exit

The doors will unlock automatically on vehicles with power door locks if:
1. The Automatic Unlock Doors On Exit feature is enabled.
2. All doors are closed.
3. The transmission gear selector was not in PARK, then is
placed in PARK.
To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to the lock or unlock position. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
4. Any door is opened.

Child-Protection Door Lock System — Rear Doors

To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child­Protection Door Lock system.
Child-Protection Door Lock Function
Page 41
NOTE:
When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
After disengaging the Child-Protection Door Lock sys­tem, always test the door from the inside to make certain it is in the desired position.
After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
For emergency exit with the system engaged, pull up on the door lock knob (unlocked position), roll down the window, and open the door with the outside door handle.
WARNING!
Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are en­gaged (locked).
GETTING TO KNOW YOUR VEHICLE 39

SEATS

Seats are a part of the Occupant Restraint System of the vehicle.
WARNING!
It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Be sure everyone in your vehicle is in a seat and using a seat belt properly.
3
Page 42
40 GETTING TO KNOW YOUR VEHICLE

Power Adjustment (Front Seats)

Some models may be equipped with eight-way power driver and front passenger seats. The power seat switches are located on the outboard side of the seat. There are two switches that control the movement of the seat cushion and the seatback.
Adjusting The Seat Forward Or Rearward
The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will move in the direction of the switch. Release the switch when the desired position has been reached.
Adjusting The Seat Up Or Down
The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch; the seat will move in the direction of the switch. Release the switch when the desired position has been reached.
Tilting The Seat Up Or Down
The angle of the seat cushion can be adjusted up or down. Pull upward or push downward on the front of the seat switch. The front of the seat cushion will move in the direction of the switch. Release the switch when the desired position has been reached.
1 — Seatback Switch 2 — Seat Switch
Power Seat Switches
Reclining The Seatback
The angle of the seatback can be adjusted forward or rearward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position is reached.
Page 43
WARNING!
Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.
Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
CAUTION!
Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
GETTING TO KNOW YOUR VEHICLE 41
Power Lumbar — If Equipped
Vehicles equipped with power driver or passenger seats may also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support. Pushing upward or downward on the switch will raise and lower the position of the support.
Power Lumbar Switch
3
Page 44
42 GETTING TO KNOW YOUR VEHICLE

Manual Adjustment (Rear Seats)

Reclining Rear Seat
To recline the seatback, lift the lever located on the out­board side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever.
Rear Seat Release
WARNING!
Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.

Driver Memory Seat — If Equipped

This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, and power tilt and telescopic steering column (if equipped) and a set of desired radio station presets. Your key fob can also be programmed to recall the same positions when the unlock button is pushed.
NOTE: Your vehicle is equipped with two key fobs, one key fob can be linked to memory position 1 and the other key fob can be linked to memory position 2.
The memory seat switch is located on the driver’s door trim panel. The switch consists of three buttons:
The set (S) button, which is used to activate the memory save function.
Page 45
The (1) and (2) buttons which are used to recall either of two pre-programmed memory profiles.
Memory Seat Switch
Programming The Memory Feature
NOTE: To create a new memory profile, perform the
following:
1. Cycle the vehicle’s ignition to the ON/RUN position (do
not start the engine).
GETTING TO KNOW YOUR VEHICLE 43
2. Adjust all memory profile settings to desired prefer­ences (i.e., seat, side mirror, power tilt and telescopic steering column [if equipped], and radio station pre­sets).
3. Push and release the set (S) button on the memory switch.
4. Within five seconds, push and release either of the memory buttons (1) or (2). The instrument cluster dis­play will display which memory position has been set.
NOTE:
Memory profiles can be set without the vehicle in PARK,
but the vehicle must be in PARK to recall a memory profile.
To set a memory profile to your key fob, refer to
“Linking And Unlinking The Remote Keyless Entry Key Fob To Memory” in this section.
Linking And Unlinking The Remote Keyless Entry Key Fob To Memory
Your key fob can be programmed to recall one of two pre-programmed memory profiles by pushing the unlock button on the key fob.
3
Page 46
44 GETTING TO KNOW YOUR VEHICLE
NOTE: Before programming your key fob you must select the “Personal Settings Linked to Key Fob” feature through the Uconnect Settings. Refer to “Uconnect Settings” in “Multimedia” for further information.
To program your key fob, perform the following:
Memory Position Recall
NOTE: The vehicle must be in PARK to recall memory
positions. If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the instrument cluster display.
1. Cycle the vehicle’s ignition to the OFF position.
2. Select a desired memory profile 1 or 2.
NOTE: If a memory profile has not already been set, refer to Programming The Memory Featurein this section for instructions on how to set a memory profile.
3. Once the profile has been recalled, push and release the set (S) button on the memory switch.
4. Push and release button (1) or (2) accordingly. “Memory Profile Set” (1 or 2) will display in the instrument cluster.
5. Push and release the lock button on the key fob within 10 seconds.
NOTE: Your key fob can be unlinked to your memory settings by pushing the set (S) button, and within 10 seconds, followed by pushing the unlock button on the key fob.
Driver One Memory Position Recall
To recall the memory settings for driver one using the memory switch, push memory button (1) on the memory switch.
To recall the memory settings for driver one using the key fob, push the unlock button on the key fob linked to memory position 1.
Driver Two Memory Position Recall
To recall the memory setting for driver two using the memory switch, push memory button (2) on the memory switch.
To recall the memory settings for driver two using the key fob, push the unlock button on the key fob linked to memory position 2.
Page 47
A recall can be canceled by pushing any of the memory buttons during a recall (S, 1, or 2), or by pushing any of the seat adjustment switches. When a recall is canceled, the driver’s seat and steering column (if equipped) stop mov­ing. A delay of one second will occur before another recall can be selected.
Easy Entry/Exit Seat
This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
The distance the driver seat moves depends on where you have the driver seat positioned when you cycle the vehi­cle’s ignition to the OFF position.
When you cycle the vehicle’s ignition to the OFF position,
the driver seat will move about 2.4 inches (60 mm) rearward if the driver seat position is greater than or equal to 2.7 inches (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you cycle the vehicle’s ignition to the ACC or RUN position.
The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.9 of an inch (22.7 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry.
GETTING TO KNOW YOUR VEHICLE 45
Each stored memory setting will have an associated Easy Entry and Easy Exit position.
NOTE: The Easy Entry/Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry/ Exit feature is enabled (or later disabled) through the programmable features in the Uconnect system. Refer to “Uconnect Settings” in “Multimedia”.

Heated Seats — If Equipped

On some models, the front and rear seats may be equipped with heaters located in the seat cushions and seat backs.
WARNING!
Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low tempera­tures, especially if used for long periods of time.
Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.
3
Page 48
46 GETTING TO KNOW YOUR VEHICLE
Front Heated Seats
The front heated seats control buttons are located within the climate or controls screen of the touchscreen.
You can choose from HI, LO, or OFF heat settings. The indicator arrows in touchscreen buttons indicate the level of heat in use. Two indicator arrows will illuminate for HI, and one for LO. Turning the heating elements off will return the user to the radio screen.
Press the heated seat button
once to turn the HI
setting on.
Press the heated seat button
a second time to turn
the LO setting on.
Press the heated seat button
a third time to turn the
heating elements off.
If the HI-level setting is selected, the system will automati­cally switch to LO-level after approximately 60 minutes of continuous operation. At that time, the display will change from HI to LO, indicating the change. The LO-level setting will turn off automatically after approximately 45 minutes.
NOTE:
Once a heat setting is selected, heat will be felt within two to five minutes.
The engine must be running for the heated seats to operate.
Vehicles Equipped With Remote Start
On models that are equipped with remote start, the heated seats can be programmed to come on during a remote start.
This feature can be programmed through the Uconnect system. Refer to “Uconnect Settings” in “Multimedia” for further information.
WARNING!
Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus­tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
(Continued)
Page 49
WARNING! (Continued)
Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.
Rear Heated Seats — If Equipped
On some models, the two rear outboard seats may be equipped with heated seats. There are two heated seat switches that allow the rear passengers to operate the seats independently. The heated seat switches for each heater are located on the rear of the center console.
GETTING TO KNOW YOUR VEHICLE 47
Rear Heated Seat Switches
You can choose from HI, LO, or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HI, one for LO and none for OFF.
Push the heated seat button
once to turn the HI
setting on.
Push the heated seat button
a second time to turn
the LO setting on.
Push the heated seat button
a third time to turn the
heating elements off.
3
Page 50
48 GETTING TO KNOW YOUR VEHICLE
When the HI-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HI-level. If the HI-level setting is selected, the system will automatically switch to LO-level after approximately 60 minutes of continuous operation. At that time, the number of indicator lights changes from two to one, indicating the change. The LO-level setting will turn off automatically after approximately 45 minutes.
WARNING!
Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus­tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.

Front Ventilated Seats — If Equipped

Located in the seat cushion and seat back are fans that draw the air from the passenger compartment and move air through fine perforations in the seat cover to help keep the driver and front passenger cooler in higher ambient temperatures. The fans operate at two speeds, HI and LO.
The front ventilated seats control buttons are located within the Uconnect system. You can gain access to the control buttons through the climate screen or the controls screen.
Press the ventilated seat button
Press the ventilated seat button
once to choose HI.
a second time to
choose LO.
Press the ventilated seat button
a third time to turn
the ventilated seat off.
NOTE: The engine must be running for the ventilated seats to operate.
Page 51
Vehicles Equipped With Remote Start
On models that are equipped with remote start, the venti­lated seats can be programmed to come on during a remote start.
This feature can be programmed through the Uconnect system. Refer to “Uconnect Settings” in “Multimedia” for further information.

To Lower Rear Seat

Either side of the rear seat can be lowered to allow for extended cargo space and still maintain some rear seating room.
NOTE: Be sure that the front seats are fully upright and positioned forward. This will allow the rear seatback to fold down easily.
1. Pull upward on the release lever to release the seat.
GETTING TO KNOW YOUR VEHICLE 49
3
Rear Seat Release
NOTE:
Do not fold the 60% rear seat down with the left outboard or rear center seat belt buckled.
Do not fold the 40% rear seat down with the right outboard seat belt buckled.
2. Fold the rear seat completely forward.
Page 52
50 GETTING TO KNOW YOUR VEHICLE
Rear Seat Folded
NOTE: You may experience deformation in the seat cush-
ion from the seat belt buckles if the seats are left folded for an extended period of time. This is normal and by simply opening the seats to the open position, over time the seat cushion will return to its normal shape.

To Raise Rear Seat

Raise the rear seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position.
WARNING!
Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in a collision. Children should be seated and using the proper restraint system.

HEAD RESTRAINTS

Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear-impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.
Page 53
WARNING!
All occupants, including the driver, should not oper­ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash.
Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.

Supplemental Active Head Restraints — Front Seats

Active Head Restraints are passive, deployable compo­nents, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspection of the head restraint. The Active Head Restraints (AHR) will be split in two halves, with the front half being soft foam and trim, the back half being decorative plastic.
GETTING TO KNOW YOUR VEHICLE 51
When AHRs deploy during a rear impact, the front half of the head restraint extends forward to reduce the gap between the back of the occupant’s head and the AHR. This system is design to reduce the risk of injury to the driver or front passenger in certain types of rear impacts. Refer to “Occupant Restraints” in “Safety” for further information.
To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push downward on the head restraint.
Adjustment Button
3
Page 54
52 GETTING TO KNOW YOUR VEHICLE
For comfort, the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Active Head Restraint (Normal Position)
Active Head Restraint (Tilted)
NOTE:
The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Safety” for further information.
Page 55
WARNING!
ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.
All occupants, including the driver, should not oper­ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players. These items may interfere with the opera­tion of the Active Head Restraint in the event of a collision and could result in serious injury or death.
Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the Active Head Restraint ensure that all cargo is secured, as loose cargo could contact the Active Head Restraint during sudden stops. Failure to follow this warning could cause personal injury if the Active Head Re­straint is deployed.
GETTING TO KNOW YOUR VEHICLE 53

Adjustment — Rear Seats

The head restraints on the outboard seats are not adjust­able. They automatically fold forward when the rear seat is folded to a load floor position, but do not return to their normal position when the rear seat is raised. After return­ing either seat to its upright position, raise the head restraint until it locks in place. The outboard head re­straints are not removable.
Folded Rear Head Restraint
The center head restraint has limited adjustment. Lift upward on the head restraint to raise it, or push downward on the head restraint to lower it.
3
Page 56
54 GETTING TO KNOW YOUR VEHICLE

Head Restraint Removal — Rear Seats

The center head restraint can be adjusted when occupied, or removed for Child Seat Tethering. To remove the head restraint, raise it as far as it can go by pulling upward. Then, push the release button at the base of the post while pulling the head restraint upward. To reinstall the head restraint, put the head restraint posts into the holes and push downward. Then, adjust the head restraint to the appropriate height.
WARNING!
ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat.
Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head re­straints are in their upright positions when the seat is to be occupied.
Center Head Restraint Release Button
NOTE: For proper routing of a Child Seat Tether, refer to
“Occupant Restraints” in “Safety” for further information.
Page 57
WARNING!
A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow re­moved head restraints in a location outside the occupant compartment.
ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat.
GETTING TO KNOW YOUR VEHICLE 55
3
STEERING WHEEL Power Tilt/Telescoping Steering Column
This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering col­umn lever is located below the multifunction lever on the steering column.

Power Tilt/Telescoping Steering Column

To tilt the steering column, move the lever up or down as desired. To lengthen or shorten the steering column, pull the lever toward you or push the lever away from you as desired.
NOTE: For vehicles equipped with Driver Memory Seat, you can use your key fob or the memory switch on the driver’s door trim panel to return the tilt/telescopic steer­ing column to pre-programmed positions. Refer to “Driver Memory Seat” in this section for further information.
Page 58
56 GETTING TO KNOW YOUR VEHICLE
WARNING!
Do not adjust the steering column while driving. Adjusting the steering column while driving or driv­ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.

Heated Steering Wheel — If Equipped

The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on, it will operate for an average of 80 minutes or more before automatically shut­ting off. This time may vary depending on the temperature of the environment. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.
The heated steering wheel control button is located within the Uconnect system. You can gain access to the control button through the climate screen or the controls screen.
Press the heated steering wheel button the heating element on.
once to turn
Press the heated steering wheel button
a second time
to turn the heating element off.
NOTE: The engine must be running for the heated steering wheel to operate.
Vehicles Equipped With Remote Start
On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start through the Uconnect system. Refer to “Uconnect Settings” in “Multimedia” for further informa­tion.
WARNING!
Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus­tion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods.
Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat.
Page 59
MIRRORS Automatic Dimming Mirror
The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
This mirror automatically adjusts for headlight glare from vehicles behind you.
NOTE: The Automatic Dimming Mirror feature is disabled when the vehicle is in REVERSE to improve the driver’s rear view.
You can turn the feature on or off by pushing the button at the base of the mirror. A light in the button will illuminate to indicate when the dimming feature is activated.
GETTING TO KNOW YOUR VEHICLE 57
3
Automatic Dimming Mirror Button
CAUTION!
To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.

Outside Mirrors

To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
Page 60
58 GETTING TO KNOW YOUR VEHICLE
WARNING!
Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in a side convex mirror.
Outside Mirrors Folding Feature
All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions:
Full forward position
Full rearward position
Normal position

Outside Automatic Dimming Mirrors — If Equipped

The outside mirrors will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror. The mirrors will auto­matically adjust for headlight glare when the inside mirror adjusts.

Power Mirrors

The power mirror switch is located on the driver’s side door trim panel.
The power mirror controls consist of mirror select buttons and a four-way mirror control switch. To adjust a mirror, push the mirror select button for the mirror that you want to adjust. Using the mirror control switch, push on any of the four arrows for the direction that you want the mirror to move.
Power Mirror Switch
1 — Mirror Direction Control 2 — Mirror Selection
Page 61
Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in “Getting To Know Your Vehicle” for further information.

Power Folding Outside Mirrors — If Equipped

If equipped with power folding mirrors, they can be electrically folded rearward and unfolded into the drive position.
The switch for the power folding mirrors is located be­tween the power mirror switches L (left) and R (right). Push the switch once and the mirrors will fold in, push the switch a second time and the mirrors will return to the normal driving position.
If the mirror is manually folded after electrically cycled, a potential extra button push is required to get the mirrors back to the home position. If the mirror does not electri­cally fold, check for ice or dirt build up at the pivot area which can cause excessive drag.
GETTING TO KNOW YOUR VEHICLE 59
3
Power Folding Mirror Switch
Automatic Power Folding Mirrors
When the Automatic Fold Mirrors feature is enabled, the exterior mirrors will fold in when exiting the vehicle (the ignition is OFF, all doors are closed, and the doors are locked).
If the exterior mirrors were auto-folded, they will unfold when the ignition is turned ON.
If the exterior mirrors were manually folded, they will not automatically unfold.
Page 62
60 GETTING TO KNOW YOUR VEHICLE
NOTE: The Automatic Fold/Unfold Mirrors feature is not turned on when delivered from the factory. The Automatic Fold/Unfold Mirrors feature can be turned on and off using the Uconnect System. Refer to “Uconnect Settings” in “Multimedia” for further information.
Resetting The Power Folding Outside Mirrors
You may need to reset the power folding mirrors if the following occurs:
The mirrors are accidentally blocked while folding.
The mirrors are accidentally manually folded/unfolded.
The mirrors come out of the unfolded position.
The mirrors shake and vibrate at normal driving speeds.
To reset the power folding mirrors: Fold and unfold them by pushing the button (this may require multiple button pushes). This resets them to their normal position.

Heated Mirrors — If Equipped

These mirrors are heated to melt frost or ice. This
feature will be activated whenever you turn on the rear window defroster (if equipped). Refer to “Climate Controls” in “Getting To Know Your Vehicle” for further information.

Tilt Side Mirrors In Reverse (Available With Memory Seat Only) — If Equipped

Tilt Side Mirrors In Reverse provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. Outside mirrors will move slightly downward from the present position when the vehicle is shifted into REVERSE. Outside mirrors will then return to the original position when the vehicle is shifted out of REVERSE position. Each stored memory seat setting will have an associated Tilt Side Mirrors In Reverse position.
NOTE: The Tilt Side Mirrors In Reverse feature is not turned on when delivered from the factory. The Tilt Side Mirrors In Reverse feature can be turned on and off using the Uconnect System. Refer to “Uconnect Settings” in “Multimedia” for further information.
Page 63

Illuminated Vanity Mirrors

To access an illuminated vanity mirror, flip down one of the visors.
Lift the cover to reveal the mirror. The light will turn on automatically.
Illuminated Vanity Mirror
GETTING TO KNOW YOUR VEHICLE 61
EXTERIOR LIGHTS Headlight Switch
The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The headlight switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights, and fog lights (if equipped).

Headlight Switch

3
Page 64
62 GETTING TO KNOW YOUR VEHICLE
To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on, the parking lights, taillights, license plate
light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (off) position.
NOTE:
Your vehicle is equipped with plastic headlight and fog
light (if equipped) lenses that are lighter and less sus­ceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
To minimize the possibility of scratching the lenses and
reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
CAUTION!
Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.

Multifunction Lever

The multifunction lever is located on the left side of the steering column.
Multifunction Lever

Daytime Running Lights — If Equipped

The Daytime Running Lights (bright intensity) come on whenever the engine is running, and the transmission is not in the PARK position. The lights will remain on until the ignition is switched to the OFF or ACC position or the parking brake is engaged.
The headlight switch must be used for normal nighttime driving.
Page 65

High/Low Beam Switch

Push the multifunction lever toward the instrument panel to switch the headlights to high beams. Pulling the multi­function back toward the steering wheel will turn the low beams back on, or shut the high beams off.

Automatic High Beam — If Equipped

The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automat­ing high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera de­tects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.
GETTING TO KNOW YOUR VEHICLE 63
NOTE:
The Automatic High Beam Headlamp Control can be turned on or off by selecting “ON” under “Auto High Beam” within your Uconnect settings, as well as turning the headlight switch to the AUTO position. Refer to “Uconnect Settings” in “Multimedia” for further infor­mation.
Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly.
If the windshield or Automatic High Beam Headlamp Control mirror is replaced, the mirror must be re-aimed to ensure proper performance. See your local authorized dealer.

Flash-To-Pass

You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the high beam headlights to turn on, and remain on, until the lever is released.
3
Page 66
64 GETTING TO KNOW YOUR VEHICLE

Automatic Headlights — If Equipped

This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the A (auto) position.
When the system is on, the Headlight Delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the OFF position. To turn the automatic headlights off, turn the headlight switch out of the A (auto) position.
NOTE: The engine must be running before the headlights will turn on in the Automatic Mode.

Parking Lights And Panel Lights

system is on. This feature is programmable through the Uconnect system screen. Refer to “Uconnect Settings” in “Multimedia” for further information.
If your vehicle is equipped with a “Rain Sensitive Wiper System” and it is activated, the headlights will automati­cally turn on after the wipers complete five wipe cycles within approximately one minute, and they will turn off approximately four minutes after the wipers completely stop. Refer to “Windshield Wipers And Washers” in “Get­ting To Know Your Vehicle” for further information.
NOTE: When your headlights come on during the day­time, the instrument panel lights will automatically dim to the lower nighttime intensity.
To turn on the parking lights and instrument panel
lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the O (off) position.

Headlights On Automatically With Wipers

If your vehicle is equipped with Automatic Headlights, it also has this customer-programmable feature. When your headlights are in the automatic mode and the engine is running, they will automatically turn on when the wiper

Headlight Delay

To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately up to 90 seconds. This delay is initiated when the ignition is turned OFF while the headlight switch is on, and then the headlight switch is cycled off. Headlight delay can be cancelled by either turning the headlight switch on then off, or by turning the ignition ON.
Page 67
NOTE:
This feature can be programmed through the Uconnect
system. Refer to “Uconnect Settings” in “Multimedia” for further information.
The headlight delay feature is automatically activated if
the headlight switch is left in the A (auto) position when the ignition is placed in the OFF position.

Lights-On Reminder

If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened.

Fog Lights — If Equipped

The fog lights are turned on by rotating the headlight switch to the parking light or headlight position and pushing in the headlight rotary control.
GETTING TO KNOW YOUR VEHICLE 65
3
Fog Light Operation
The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illu­minate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected.

Turn Signals

Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 68
66 GETTING TO KNOW YOUR VEHICLE
NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defec­tive.

Lane Change Assist — If Equipped

Tap the multifunction lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off.

Automatic Headlight Leveling — HID Headlights Only

This feature prevents the headlights from interfering with the vision of oncoming drivers. Headlight leveling auto­matically adjusts the height of the headlight beam in reaction to changes in vehicle pitch.

Battery Saver

To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights.
If the ignition is OFF and any door is left ajar for 10 minutes or the dimmer control is rotated all the way up to the dome on position for 10 minutes, the interior lights will automati­cally turn off.
NOTE: Battery saver mode is canceled if the ignition is ON.
If the headlights remain on while the ignition is cycled OFF, the exterior lights will automatically turn off after eight minutes. If the headlights are turned on and left on for eight minutes while the ignition is OFF, the exterior lights will automatically turn off.

INTERIOR LIGHTS

Courtesy and dome lights are turned on when the front doors are opened or when the dimmer control (rotating wheel on the right side of the headlight switch) is rotated to its farthest upward position. If your vehicle is equipped with remote keyless entry and the unlock button is pushed on the key fob, the courtesy and dome lights will turn on. When a door is open and the interior lights are on, rotating the dimmer control all the way down, to the last (off) detent, will cause all the interior lights to go out. This is also known as the “Party” mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
Page 69

Courtesy Lights

The courtesy lights can be turned on by pushing the top corner of the lens. To turn the lights off, push the lens a second time.
Courtesy Lights
GETTING TO KNOW YOUR VEHICLE 67
Front Map/Reading Lights — If Equipped
The front map/reading lights are mounted in the overhead console.
3
Front Map/Reading Lights
Page 70
68 GETTING TO KNOW YOUR VEHICLE
Each light can be turned on by pushing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, push the switch a second time. The lights will also turn on when the unlock button on the remote keyless entry key fob is pushed.
Ambient Light — If Equipped
The overhead console is equipped with an ambient light feature. This light casts illumination for improved visibility of the floor and center console area.
Front Map/Reading Light Switches
Ambient Light
Page 71
Dimmer Controls
The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer). When the headlights are on you can supplement the brightness of the instrument cluster dis­play, radio and overhead console by rotating the control to its farthest position up until you hear a click. This feature is termed the “Parade” mode and is useful when head­lights are required during the day.
Dimmer Control
GETTING TO KNOW YOUR VEHICLE 69

WINDSHIELD WIPERS AND WASHERS

The windshield wiper/washer controls are located on the multifunction lever on the left side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “Rear Window Wiper/Washer” in this section.
Multifunction Lever
3
Page 72
70 GETTING TO KNOW YOUR VEHICLE

Windshield Wiper Operation

Rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation.
Windshield Wiper Operation
CAUTION!
Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur.
Intermittent Wiper System
Use one of the four intermittent wiper settings when weather conditions make a single wiping cycle, with a variable delay between cycles, desirable. At driving speeds above 10 mph (16 km/h), the delay can be regulated from a maximum of approximately 18 seconds between cycles (first detent), to a cycle every one second (fourth detent).
Page 73
Intermittent Wiper Operation Windshield Washer Operation
NOTE: If the vehicle is moving less than 10 mph
(16 km/h), delay times will be doubled.
Windshield Washer Operation
To use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected.
GETTING TO KNOW YOUR VEHICLE 71
3
If the end of the lever is pushed while the wipers are in the off position, the wipers will operate for several wipe cycles, then turn off.
WARNING!
Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the wind­shield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Page 74
72 GETTING TO KNOW YOUR VEHICLE
Mist
Use the Mist feature when weather conditions make occa­sional usage of the wipers necessary. Rotate the end of the lever downward to the MIST position and release for a single wiping cycle.
NOTE: The Mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid.

Rain Sensing Wipers — If Equipped

This feature senses rain or snowfall on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of four settings to activate this feature.
The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position one is the least sensitive, and wiper delay position four is the most sensi­tive.
NOTE: Wiper delay position three should be used for normal rain conditions.
Settings one and two can be used if the driver desires less wiper sensitivity. Setting four can be used if the driver desires more sensitivity. Place the wiper switch in the OFF position when not using the system.
NOTE:
The Rain Sensing feature will not operate when the wiper switch is in the low or high-speed position.
The Rain Sensing feature may not function properly when ice, or dried salt water is present on the wind­shield.
Use of Rain-X or products containing wax or silicone may reduce Rain Sensing performance.
The Rain Sensing feature can be turned on and off using the Uconnect System, refer to “Uconnect Settings” in “Multimedia” for further information.
The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions:
Low Ambient Temperature — When the ignition is first turned ON, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 3 mph (5 km/h), or the outside temperature is greater than 32°F (0°C).
Page 75
Transmission In NEUTRAL Position — When the igni- tion is ON, and the automatic transmission is in the NEUTRAL position, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 3 mph (5 km/h), or the gear selector is moved out of the NEUTRAL position.
Remote Start Mode Inhibit — On vehicles equipped with Remote Starting system, Rain Sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the RUN position, rain sensing wiper operation can resume, if it has been selected, and no other inhibit conditions (mentioned previously) exist.

Rear Window Wiper/Washer

The rear wiper/washer controls are located on the multi­function lever on the left side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever.
GETTING TO KNOW YOUR VEHICLE 73
3
Rear Wiper/Washer Control
Rotate the center portion of the lever upward to the first detent for intermittent operation and to the
second detent for continuous rear wiper operation.
Rotating the center portion upward once more will
activate the washer pump which will continue to operate as long as the switch is held. Upon release of the switch, the wipers will resume the continuous rear wiper operation. When this rotary control is in the OFF position, rotating it downward will activate the rear washer pump which will continue to operate as long as the switch is held.
Page 76
74 GETTING TO KNOW YOUR VEHICLE
Once the switch is released it will return to the OFF position and the wipers will cycle several times before returning to the parked position.
NOTE: As a protective measure, the pump will stop if the switch is held for more than 20 seconds. Once the switch is released the pump will resume normal operation.
If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “park” position.

HEADLIGHT WASHERS — IF EQUIPPED

The multifunction lever operates the headlight washers when the ignition switch is in the ON position and the headlights are turned on. The multifunction lever is located on the left side of the steering column.
To use the headlight washers, push the multifunction lever inward (toward the steering column) and release it. The headlight washers will spray a timed high-pressure spray of washer fluid onto each headlight lens. In addition, the windshield washers will spray the windshield and the windshield wipers will cycle.
NOTE: After turning the ignition switch and headlights ON, the headlight washers will operate on the first spray of the windshield washer and then every eleventh spray after that.
Page 77
CLIMATE CONTROLS Automatic Climate Controls Overview
The Climate Control System allows you to regulate the temperature, air flow, and direction of air circulating
Uconnect 4C/4C NAV With 8.4–inch Display Automatic Climate Controls
GETTING TO KNOW YOUR VEHICLE 75
throughout the vehicle. The controls are located on the instrument panel below the radio.
3
Page 78
76 GETTING TO KNOW YOUR VEHICLE
Control Descriptions
Icon Description
MAX A/C Button
Press and release to change the current setting, the indicator illuminates when MAX A/C is on. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
A/C Button
Press and release to change the current setting. The indicator illuminates when A/C is on.
Recirculation Button
Press and release this button on the touchscreen, or push the button on the faceplate, to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions, such as smoke, odors, dust, or high humidity are present. Recirculation can be used in all modes. The A/C can be deselected manually without disturbing the mode control selection. Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended.
AUTO Button
Automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between manual mode and auto­matic modes. Refer to “Automatic Operation” within this section for more information.
Page 79
Icon Description
Front Defrost Button
The Front Defrost button changes the current airflow setting to Defrost mode. The indicator illu­minates when this feature is on. Air comes from the windshield and side window demist out­lets. When the defrost button is selected, the blower level may increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. When toggling the front defrost mode button, the climate system will return to previous setting.
Rear Defrost Button
The Rear Defrost Control button turns on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ten minutes.
Driver And Passenger Temperature Up And Down Buttons
Provides the driver and passenger with independent temperature control. Push the red button on the faceplate or touchscreen or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings. Push the blue button on the face­plate or touchscreen or press and slide the temperature bar towards the blue arrow button on the touchscreen for cooler temperature settings.
SYNC Button
Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indica­tor is illuminated when this feature is enabled. SYNC is used to synchronize the passenger tem­perature setting with the driver temperature setting. Changing the passenger’s temperature set­ting while in SYNC will automatically exit this feature.
GETTING TO KNOW YOUR VEHICLE 77
3
Page 80
78 GETTING TO KNOW YOUR VEHICLE
Icon Description
Faceplate Knob
Blower Control
Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen.
Touchscreen
Buttons
Faceplate: The blower speed increases as you turn the blower control knob clockwise from the lowest blower setting. The blower speed decreases as you turn the blower control knob counterclockwise.
Touchscreen: Use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting. The blower can also be selected by pressing the blower bar area between the icons.
Panel Mode Panel Mode
Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction. There is a shut off wheel lo­cated below the air vanes to shut off or adjust the amount of airflow from these outlets.
Bi-Level Mode
Bi-Level Mode
Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
NOTE:
Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel out­lets and warmer air from the floor outlets.
Page 81
Icon Description
Floor Mode
Floor Mode
Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
GETTING TO KNOW YOUR VEHICLE 79
3
Mix Mode
Mix Mode
Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
Climate Control OFF Button
This button turns the Climate Control System off.

Climate Control Functions

A/C (Air Conditioning)
The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning sys­tem. When the air conditioning system is turned on, cool dehumidified air will flow through the outlets into the cabin. For improved fuel economy, press the A/C button to turn off the air conditioning and manually adjust the blower and airflow mode settings. Also, make sure to select only Panel, Bi-Level, or Floor modes.
NOTE:
If fog or mist appears on the windshield or side glass, select Defrost mode, and increase blower speed if needed.
If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of dirt or insects. Clean with a gentle water spray from the front of the radiator and through the condenser.
Page 82
80 GETTING TO KNOW YOUR VEHICLE
MAX A/C
MAX A/C sets the control for maximum cooling perfor­mance.

Automatic Temperature Control (ATC) — If Equipped

Automatic Operation
Press and release to toggle between MAX A/C and the prior settings. The button illuminates when MAX A/C is on.
In MAX A/C, the blower level and mode position can be adjusted to desired user settings. Pressing other settings will cause the MAX A/C operation to switch to the selected setting and MAX A/C to exit.
Recirculation
In cold weather, use of Recirculation mode may lead to excessive window fogging. The Recirculation feature may be unavailable (button on the touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield.
On systems with Manual Climate Controls, the Recircula­tion mode is not allowed in Defrost mode to improve window clearing operation. Recirculation is disabled auto­matically if this mode is selected. Attempting to use Recirculation while in this mode causes the LED in the control button to blink and then turns off.
1. Push the AUTO button on the faceplate, or the AUTO
button on the touchscreen on the Automatic Tempera­ture Control (ATC) Panel.
2. Next, adjust the temperature you would like the system
to maintain by adjusting the driver and passenger temperature control buttons. Once the desired tempera­ture is displayed, the system will achieve and automati­cally maintain that comfort level.
3. When the system is set up for your comfort level, it is
not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically.
Page 83
NOTE:
It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible.
The temperature can be displayed in U.S. or Metric units by selecting the US/Metric customer-programmable fea­ture. Refer to the “Uconnect Settings” in “Multimedia” for further information.
To provide you with maximum comfort in the Automatic mode during cold start-ups, the blower fan will remain on low until the engine warms up. The blower will increase in speed and transition into Auto mode.
Manual Operation Override
This system offers a full complement of manual override features. The AUTO symbol in the front ATC display will be turned off when the system is being used in the manual mode.

Operating Tips

NOTE: Refer to the chart at the end of this section for suggested control settings for various weather conditions.
GETTING TO KNOW YOUR VEHICLE 81
Summer Operation
The engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating. OAT coolant (conforming to MS.90032) is recommended.
Winter Operation
To ensure the best possible heater and defroster perfor­mance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Use of the Air Recirculation mode during Winter months is not recommended, because it may cause window fogging.
Vacation/Storage
Before you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes, in fresh air with the blower setting on high. This will ensure adequate system lubrication to minimize the possibility of compressor dam­age when the system is started again.
3
Page 84
82 GETTING TO KNOW YOUR VEHICLE
Window Fogging
Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather. To clear the windows, select De­frost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur.
CAUTION!
Failure to follow these cautions can cause damage to the heating elements:
Use care when washing the inside of the rear win­dow. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heat­ing elements. Labels can be peeled off after soaking with warm water.
Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the win­dow.
Keep all objects a safe distance from the window.
Outside Air Intake
Make sure the air intake, located directly in front of the windshield, is free of obstructions, such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In Winter months, make sure the air intake is clear of ice, slush, and snow.
Cabin Air Filter
The climate control system filters out dust and pollen from the air. Contact an authorized dealer to service your cabin air filter, and to have it replaced when needed.
Page 85
Operating Tips Chart WINDOWS

Power Window Controls

The window controls on the driver’s door control all the door windows.
There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the ACC or ON/RUN position.
GETTING TO KNOW YOUR VEHICLE 83
3
Power Window Switches
Page 86
84 GETTING TO KNOW YOUR VEHICLE
NOTE: For vehicles equipped with Uconnect, the power window switches will remain active for up to 10 minutes after the ignition is cycled to the OFF position. Opening either front door will cancel this feature. The time is programmable. Refer to “Uconnect Settings” in “Multime­dia” for further information.
WARNING!
Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/ RUN mode. Occupants, particularly unattended chil­dren, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.

Auto-Down Feature

The driver door power window switch and the front and rear passenger doors window switches have an Auto­Down feature.
Push the window switch down for half a second and release. The window will go down automatically.
To stop the window from going all the way down during the Auto-Down operation, pull up or push down on the switch briefly.
To open the window part way (manually), push the window switch down briefly and release.

Auto-Up Feature With Anti-Pinch Protection

Lift the window switch up, for a short period of time, and release and the window will go up automatically.
To stop the window from going all the way up during the Auto-Up operation, push down on the switch briefly.
To close the window part way, lift the window switch briefly and release it when you want the window to stop.
NOTE:
If the window runs into any obstacle during auto­closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window.
Any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during auto­closure. If this happens, pull the switch lightly and hold to close the window manually.
Page 87
WARNING!
There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear your arms, hands, fingers and all objects from the window path before closing.

Reset Auto-Up

Should the Auto-Up feature stop working, the window probably needs to be reset. To reset Auto-Up:
1. Pull the window switch up to close the window com­pletely and continue to hold the switch up for an additional two seconds after the window is closed.
Push the window switch down firmly to open the win-
2. dow completely and continue to hold the switch down for an additional two seconds after the window is fully open.

Window Lockout Switch

The window lockout switch on the driver’s door trim panel allows you to disable the window controls on the rear passenger doors. To disable the window controls, push and release the window lockout button (the indicator light on the button with turn on). To enable the window controls, push and release the window lockout button again (the indicator light on the button will turn back off).
GETTING TO KNOW YOUR VEHICLE 85
3
Window Lockout Switch

Wind Buffeting

Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.
Page 88
86 GETTING TO KNOW YOUR VEHICLE

COMMANDVIEW SUNROOF WITH POWER SHADE — IF EQUIPPED

The CommandView sunroof switch is located to the left between the sun visors on the overhead console.
The power shade switch is located to the right between the sun visors on the overhead console.
CommandView Sunroof And Power Shade Switches
WARNING!
Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sun­roof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are also properly secured.
Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. In­jury may result.
Page 89

Opening Sunroof

The sunroof has two programmed automatic stops for the sunroof open position; a comfort stop position and a full open position. The comfort stop position has been opti­mized to minimize wind buffeting.
Express
Push the switch rearward and release it within one-half second. The sunroof will open automatically to the comfort stop position. Push the switch rearward and release it again, the sunroof will open to the full open position and automatically stop. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof.
Manual Mode
To open the sunroof, push and hold the switch rearward. The sunroof will stop automatically at the comfort stop position. Push and hold the switch rearward again, the sunroof will open to the full open position and automati­cally stop. Any release of the switch will stop the move­ment. The sunroof and sunshade will remain in a partially opened condition until the switch is pushed and held rearward again.
GETTING TO KNOW YOUR VEHICLE 87
NOTE: If the sunshade is in the closed position when Express or Manual Open operation is initiated the sun­shade will automatically open to the half open position prior to the sunroof opening.

Closing Sunroof

Express Mode
Push the switch forward and release it within one-half second and the sunroof will close automatically from any position. The sunroof will close fully and stop automati­cally. This is called “Express Close”. During Express Close operation, any other actuation of the switch will stop the sunroof.
Manual Mode
To close the sunroof, push and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the sunroof switch is pushed again.

Wind Buffeting

Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or
3
Page 90
88 GETTING TO KNOW YOUR VEHICLE
partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.

Opening Power Shade

Express
Push the shade switch rearward and release it within one-half second and the shade will automatically open to the halfway position and stop automatically. Push the switch a second time from the halfway position and the shade will automatically open to the full open position and stop automatically. This is called “Express Open”. During Express Open operation, any movement of the shade switch will stop the shade.
Manual Mode
To open the shade, push and hold the switch rearward. The shade will open and stop automatically at the half-open position. Push and hold the shade switch rearward again and the shade will open automatically to the full-open
position. Any release of the switch will stop the movement and the shade will remain in a partially opened condition until the switch is pushed again.

Closing Power Shade

Express
Push the switch forward and release it within one-half second and the shade will close automatically from any position. If the sunroof is completely closed the shade will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the shade.
NOTE: If the sunroof is open, the shade will close to the half-open position. Pushing the shade close button again will automatically close both the sunroof and shade com­pletely.
Manual
To close the shade, push and hold the switch in the forward position. Any release of the switch will stop the movement and the shade will remain in a partially closed condition until the switch is pushed again.
Page 91

Pinch Protect Feature

This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this oc­curs.
NOTE: If three consecutive sunroof close attempts result in Pinch Protect reversals, Pinch Protect will disable and the sunroof must be closed in Manual Mode.

Venting Sunroof — Express

Push and release the Ventbutton within one-half second and the sunroof will open to the vent position. This is called “Express Vent”, and it will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.
NOTE: If the sunshade is in the closed position when the vent switch is pushed, the sunshade will automatically cycle to the halfway open position prior to the sunroof opening to the Vent position.

Sunroof Maintenance

Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.
GETTING TO KNOW YOUR VEHICLE 89
HOOD To Open The Hood
To open the hood, two latches must be released.
1. Pull the release lever located below the instrument panel and in front of the driver’s door.
Hood Release
3
Page 92
90 GETTING TO KNOW YOUR VEHICLE
2. Reach under the hood, move safety latch to the left and lift the hood.
Safety Latch Location

To Close The Hood

1. Hold up the hood with one hand and with the other hand remove the support rod from its seat and reinsert it into the locking tab.
2. Lower the hood to approximately 12 inches (30 cm) from the engine compartment and drop it. Make sure that the hood is completely closed.
WARNING!
Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.
CAUTION!
To prevent possible damage, do not slam the hood to close it. Lower hood to approximately 12 inches (30 cm) and drop the hood to close. Make sure hood is fully closed for both latches. Never drive vehicle unless hood is fully closed, with both latches engaged.
LIFTGATE Opening
The liftgate can be opened from inside the vehicle using the power liftgate button on the overhead console, using the key fob outside of the vehicle or the electronic liftgate release.
Page 93
To Unlock/Enter The Liftgate
The liftgate may be released in several ways:
Key fob
Outside handle
Button on overhead console
The liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the electronic liftgate release to open with one fluid motion. Push the button on the key fob twice within five seconds to release the liftgate.
NOTE: If “Unlock All Doors 1st Press” is programmed in the instrument cluster display, all doors will unlock when you push the electronic release on the liftgate. If Unlock Driver Door 1st Pressis programmed in Uconnect, only the liftgate will unlock when you push the electronic release on the liftgate. Refer to “Uconnect Settings” in “Multimedia” for further information.
GETTING TO KNOW YOUR VEHICLE 91
3
Passive Entry/Lock Button Location
1 — Electronic Liftgate Release 2 — Lock Button Location
NOTE: Use the power door lock switch on either front door trim panel or the key fob to lock and unlock the liftgate. The manual door locks on the doors and the driver’s door lock cylinder will not lock and unlock the liftgate.
Page 94
92 GETTING TO KNOW YOUR VEHICLE
WARNING!

Power Liftgate — If Equipped

Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passen­gers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.

Closing

Grasp the liftgate closing handle and initiate lowering the liftgate. Release the handle when the liftgate takes over the closing effort.
To Lock The Liftgate
With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, pushing the Keyless Enter-N-Go — Passive Entry lock button located to the left of the outside handle release will lock the vehicle.
The power liftgate may be closed by pushing the button, located in the upper left trim in the liftgate opening. Pushing button will only close the liftgate. This button cannot be used to open the liftgate.
NOTE: The liftgate unlock feature is built into the elec­tronic liftgate release.
The power liftgate may be opened by pushing the electronic liftgate release (refer to “Keyless Enter-N-Go — Passive Entry” located in “Get-
ting To Know Your Vehicle” for further informa­tion), or by pushing the liftgate button on the key fob. Push the liftgate button on the key fob twice within five seconds to open the power liftgate. Once the liftgate is open, pushing the button twice within five seconds a second time will close the liftgate.
The power liftgate may also be opened or closed by pushing the liftgate button located on the front overhead console. If the liftgate is fully open, the liftgate can be closed by pushing the liftgate button located on the left rear trim panel, near the liftgate opening. If the liftgate is in motion, pushing the liftgate button located on the left rear trim panel will reverse the liftgate.
When the liftgate button on the key fob is pushed two times, the turn signals will flash to signal that the liftgate is opening or closing (if Flash Lamps with Lock is enabled in the Uconnect settings), and the liftgate chime will be audible. Refer to Uconnect Settingsin Multimedia” for further information.
Page 95
NOTE:
In the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel.
If liftgate is left open for an extended period of time, the liftgate may need to be closed manually to reset power liftgate functionality.
WARNING!
During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away.
GETTING TO KNOW YOUR VEHICLE 93
NOTE:
The power liftgate buttons will not operate if the vehicle is in gear or the vehicle speed is above 0 MPH (0 km/h).
The power liftgate will not operate in temperatures below −22°F (−30°C) or temperatures above 150° F (65° C). Be sure to remove any buildup of snow or ice from the liftgate before pushing any of the power liftgate switches.
If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically re­verse to the closed or open position, provided it meets sufficient resistance.
There are also pinch sensors attached to the side of the liftgate. Light pressure anywhere along these strips will cause the liftgate to return to the open position.
If the liftgate is not fully open, push the liftgate button on the key fob twice to operate the liftgate.
If the electronic liftgate release is pushed while the power liftgate is closing, the liftgate will reverse to the full open position.
If the electronic liftgate release is pushed while the power liftgate is opening, the liftgate motor will disen­gage to allow manual operation.
3
Page 96
94 GETTING TO KNOW YOUR VEHICLE
If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and the liftgate must be opened or closed manually.
WARNING!
Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas­sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode.

Cargo Area Features

Cargo Storage Bins
There are up to four removable storage bins located in the rear cargo area. There are two storage bins located on either side of the cargo area.
NOTE: If your vehicle is equipped with a rear subwoofer, the storage bin on that side will not be available.
Rear Storage Bin
Page 97
Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether strap (attached to the bottom of the load floor) to the liftgate opening.
Tether Strap
GETTING TO KNOW YOUR VEHICLE 95
3
Rear Lower Storage Bins
Retractable Cargo Area Cover — If Equipped
NOTE: The purpose of this cover is for privacy, not to
secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo.
To cover the cargo area:
1. Grasp the cover at the center handle. Pull it over the cargo area.
2. Insert the pins on the ends of the cover into the slots in the pillar trim cover.
Page 98
96 GETTING TO KNOW YOUR VEHICLE
3. The liftgate may be opened with the cargo cover in place.
Rear Cargo Cover
Rear Cargo Tie-Downs
The rear cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving.
WARNING!
In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart­ment. Remove the cover from the vehicle when taken from its mounting. Do not store it in the vehicle.
Rear Cargo Tie-Downs
Page 99
GETTING TO KNOW YOUR VEHICLE 97
WARNING!
To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts.
Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle han­dling. To avoid loss of control resulting in personal injury, follow these guidelines for loading your ve­hicle:
Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar.
Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible.
(Continued)
WARNING! (Continued)
Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway.
Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or accident.

GARAGE DOOR OPENER — IF EQUIPPED

HomeLink replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink unit is powered by your vehicle’s 12 Volt battery.
The HomeLink buttons, located on the overhead console, designate the three different HomeLink channels. The HomeLink indicator is located above the center button.
3
Page 100
98 GETTING TO KNOW YOUR VEHICLE
HomeLink Buttons/Overhead Console
NOTE: HomeLink is disabled when the Vehicle Security
Alarm is active.

Before You Begin Programming HomeLink

Be sure that your vehicle is parked outside of the garage before you begin programming.
For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink system.
To erase the channels, place the ignition in the ON/RUN position, and push and hold the two outside HomeLink buttons (I and III) for up to 20 seconds or until the orange indicator flashes.
NOTE:
Erasing all channels should only be performed when programming HomeLink for the first time. Do not erase channels when programming additional buttons.
If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manufac­tured after 1995. These garage door openers can be identi­fied by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener.
NOTE: It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer.
Loading...