Jeep Patriot 2010 User Manual

2O1O Patriot

USER GUIDE

IMPORTANT: This User Guide is intended to familiarize you with the important features of your
vehicle. The DVD enclosed contains your Owner’s Manual, Navigation Radio or Multimedia
Radio Manual, Warranty Booklets, Tire Warranty and 24-Hour Towing Assistance (new vehicles
purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic
format. We hope you nd it useful. If you are the rst registered owner of your vehicle, you may
obtain a printed copy of the Owner’s Manual, Navigation Radio or Multimedia Radio Manual or
Warranty Booklet by calling 1-800-992-1997 (U.S.) or 1-800-387-1143 (Canada) or by contacting
your dealer. Replacement manuals may be purchased by visiting www.techauthority.com.

Jeep® is a registered trademark of Chrysler Group LLC. Copyright © 2009 Chrysler Group LLC.

TABLE OF CONTENTS

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC

.. 2

CONTROLS AT A GLANCE

DRIVER COCKPIT .............. 4

INSTRUMENT CLUSTER .......... 6

GETTING STARTED

KEYFOB ..................8

THEFT ALARM ............... 9

SEAT BELT ................. 9

CHILD RESTRAINTS ............ 9

FRONT SEATS ...............11

REAR SEATS ................14

TILT STEERING COLUMN .........14

PROGRAMMABLE FEATURES .......15

OPERATING YOUR VEHICLE

TURN SIGNAL/LIGHTS LEVER .......17

WIPER/WASHER LEVER ..........18

SPEED CONTROL LEVER .........19

CONTINUOUSLY VARIABLE AUTOMATIC

TRANSMISSION (CVT) ...........20

MANUAL CLIMATE CONTROLS ......20

AUTOMATIC TEMPERATURE CONTROLS

(ATC) ....................21

POWER SUNROOF .............21

WIND BUFFETING .............22

ELECTRONICS

NON-TOUCH-SCREEN RADIOS ......23

TOUCH-SCREEN RADIOS .........26

REMOTE AUDIO CONTROLS ........30

UNIVERSAL CONSUMER INTERFACE . . . 31
ELECTRONIC VEHICLE INFORMATION

CENTER (EVIC) ...............31

UNIVERSAL GARAGE DOOR OPENER . . . 32

POWER INVERTER .............33

POWER OUTLET ..............34

UCONNECT™ PHONE ...........34

VOICE COMMAND .............36

OFF-ROAD CAPABILITIES

FOUR-WHEEL DRIVE OPERATION .....37

UTILITY

TRAILER TOWING WEIGHTS (MAXIMUM

TRAILER WEIGHT RATINGS) ........38

RECREATIONAL TOWING (BEHIND

MOTORHOME, ETC.) ............39

BRAKE/TRANSMISSION INTERLOCK

MANUAL OVERRIDE SYSTEM .......39

WHAT TO DO IN EMERGENCIES

24 HOUR TOWING ASSISTANCE -

U.S. ONLY ..................40

INSTRUMENT CLUSTER WARNING

LIGHTS ...................40

IF YOUR ENGINE OVERHEATS .......43

AUTOMATIC TRANSAXLE OVERHEATING

JACKING AND TIRE CHANGING ......44

JUMP-STARTING ..............47

TOWING A DISABLED VEHICLE ......51

FREEING A STUCK VEHICLE ........52

EVENT DATA RECORDER (EDR) ......53

..44

MAINTAINING YOUR VEHICLE

OPENING THE HOOD ............54

ENGINE COMPARTMENT .........55

FLUIDS AND CAPACITIES .........57

MAINTENANCE CHART ..........58

FUSES ...................60

TIRE PRESSURES .............61

WHEEL AND WHEEL TRIM CARE .....62

EXTERIOR BULBS .............62

CONSUMER ASSISTANCE

CHRYSLER GROUP LLC CUSTOMER

CENTER ...................63

CHRYSLER CANADA INC. CUSTOMER

CENTER ...................63

ASSISTANCE FOR THE HEARING

IMPAIRED ..................63

PUBLICATIONS ORDERING ........63

REPORTING SAFETY DEFECTS IN THE
50 UNITED STATES

AND WASHINGTON, D.C. .........64

TIRE WARRANTY ..............64

MOPAR ACCESSORIES

MOPAR® ACCESSORIES ..........67

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it
represents precision workmanship, distinctive styling, and high quality - all essentials that
are traditional to our vehicles.

IMPORTANT: This User Guide is intended to familiarize you with the important features of
your vehicle. The DVD enclosed contains your Owner’s Manual, Warranty Booklets, Tire
Warranty, and 24-Hour Towing Assistance (new vehicles purchased in the U.S.) or Roadside
Assistance (new vehicles purchased in Canada) in electronic format. We hope you find it
useful. Retail customers may obtain a printed copy of any of these booklets; call
1-800-890-4038 (U.S.) or 1-800-387-1143 (Canada) or ask your dealer.

For complete owner information, refer to the DVD in the owner’s kit provided at the time of
new vehicle purchase. For your convenience, the information contained on the DVD may
also be printed and saved for future reference.

Not all features shown in this guide may apply to your vehicle.

Chrysler Group LLC is committed to protecting our environment and natural resources. By
converting from paper to electronic delivery for the majority of the user information for your
vehicle, together we greatly reduce the demand for tree-based products and lessen the
stress on our environment.

Vehicles Sold In Canada

With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed
to be deleted and the name Chrysler Canada Inc. used in substitution therefore.

Driving And Alcohol

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol levels far below the legal
minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a
cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your
reflexes are slower, and your judgment is impaired when you have been drinking.
Never drink and then drive.

This guide illustrates and describes the operation of features and equipment that are either
standard or optional on this vehicle. This guide may also include a description of features
and equipment that are no longer available or were not ordered on this vehicle. Please
disregard any features and equipment described in this guide that are not available on this
vehicle. Chrysler Group LLC reserves the right to make changes in design and
specifications and/or make additions to or improvements to its products without imposing
any obligation upon itself to install them on products previously manufactured.

2

INTRODUCTION/WELCOME

Rollover Warning

WARNING!

Never use the ‘PARK’ position as a substitute for the parking brake. Always apply the
parking brake fully when parked to guard against vehicle movement and possible
injury or damage.

CAUTION!

Never park your vehicle over dry grass or other combustible materials. The heat
from your vehicle exhaust system could cause a fire.

CHRYSLER, DODGE, JEEP, ATF+4, MOPAR and Uconnect are registered trademarks of
Chrysler Group LLC.

COPYRIGHT ©2009 CHRYSLER GROUP LLC

3

CONTROLS AT A GLANCE

DRIVER COCKPIT

4

CONTROLS AT A GLANCE

5

CONTROLS AT A GLANCE

INSTRUMENT CLUSTER

Warning Lights

- Low Fuel Warning Light

- Charging System Light**

- Oil Pressure Warning Light**

- Anti-Lock Brake (ABS) Light**

- Airbag Warning Light**

- Electronic Throttle Control (ETC) Light

- Tire Pressure Monitoring System (TPMS) Light

- Engine Temperature Warning Light

- Transmission Temperature Warning Light

- Seat Belt Reminder Light

BRAKE

- Brake Warning Light**

- Malfunction Indicator Light (MIL)**

- Electronic Stability Control (ESC) Malfunction Indicator Light**

- 4WD System Fault Indicator Light**

6

CONTROLS AT A GLANCE

Indicators

- Turn Signal Indicators

- High Beam Indicator

- Front Fog Light Indicator

- Vehicle Security Indicator*

- 4WD Indicator

- Electronic Stability Control
(ESC) Off Indicator

OFF
ROAD

- Cruise Indicator

- Hill Descent Control
Indicator

- OFF ROAD Indicator

Odometer Messages

door - Door Ajar Lo tIrE - Low Tire Pressure
gate - GateAjar CHAngE OIL* - Change Engine Oil
gASCAP - Fuel Cap Fault

* If equipped
** Bulb Check with Key On

7

GETTING STARTED

KEY FOB

Locking And Unlocking The Doors/Liftgate

• Press the LOCK button once to lock all the
doors and the liftgate. Press the UNLOCK
button once to unlock the driver’s door only
and twice within five seconds to unlock all the
doors and liftgate.

• All doors can be programmed to unlock on
the first press of the UNLOCK button. Refer to
Programmable Features in this guide.

WARNING!

Leaving unattended children in a vehicle is dangerous for a number of reasons. A
child or others could be injured. Children should be warned not to touch the parking
brake, brake pedal, or the shift lever. Do not leave the key in the ignition. A child
could operate power windows, other controls, or move the vehicle.

Remote Start

NOTE: The vehicle must be equipped with an automatic transaxle to be equipped with
Remote Start.

x

2

• Press the REMOTE START button
START button a third time shuts the engine off.

• To drive the vehicle, press the UNLOCK button, insert the key in the ignition and turn to
the ON/RUN position.

• With remote start, the engine will only run for 15 minutes (timeout) unless the ignition
key is placed in the ON/RUN position.

• The vehicle must be started with the key after two consecutive timeouts.

twice within five seconds. Pressing the REMOTE

WARNING!

• Do not start or run an engine in a closed garage or confined area. Exhaust gas
contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide
is poisonous and can cause serious injury or death when inhaled.

• Keep Key Fob transmitters away from children. Operation of the Remote Start
System, windows, door locks or other controls could cause serious injury or
death.

8

GETTING STARTED

Panic Alarm

• Press the PANIC button once to turn the panic alarm on.

• Wait approximately three seconds and press the button a second time to turn the panic
alarm off.

THEFT ALARM

To Arm

• Press the Key Fob LOCK button or the power door lock switch while the door is open.

To Disarm

• Press the Key Fob UNLOCK button and turn the ignition to the ON position.

SEAT BELT

• Be sure everyone in your vehicle is in a seat and using a seat belt properly.

WARNING!

In a collision, you and your passengers can suffer much greater injuries if you are
not properly buckled up. You can strike the interior of your vehicle or other
passengers, or you can be thrown out of the vehicle. Always be sure you and others
in your vehicle are buckled up properly.

CHILD RESTRAINTS

• Every state in the United States and all Canadian provinces require that small children
ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring
it.

WARNING!

In a collision, an unrestrained child, even a tiny baby, can become a projectile inside
the vehicle. The force required to hold even an infant on your lap could become so
great that you could not hold the child, no matter how strong you are. The child and
others could be badly injured. Any child riding in your vehicle should be in a proper
restraint for the child’s size.

Installing The LATCH - Compatible Child Restraint System

• Your vehicle's second row passenger seats are equipped with the child restraint
anchorage system called LATCH, which stands for Lower Anchors and Tether for
CHildren. LATCH child restraint anchorage systems are installed at all three rear seating
positions.

• The rear outboard seating positions have lower anchors and all three rear seating
positions have top tether anchors.

9

GETTING STARTED

• Child seats with fixed lower attachments must be installed in the outboard positions only.
Child seats with flexible lower attachments can be used in all three seating positions.

• NEVER install LATCH-compatible child seats such that two seats share a common lower
anchorage.

• Loosen the adjusters on the lower straps and
tether straps so that you can attach the hook
or connector to the lower and tether
anchorages more easily.

• Attach the lower hooks or connectors over
the top of the seatcover material.

• The tether strap should be routed under the
center of the head restraint and attached to
the tether anchor on the rear of the seatback.

• Tighten all three straps as you push the child restraint rearward and downward into the
seat.

WARNING!

• Improper installation of a child restraint to the LATCH anchorages can lead to
failure of an infant or child restraint. The child could be badly injured or killed.
Follow the manufacturer’s directions exactly when installing an infant or child
restraint.

• An incorrectly anchored tether strap could lead to increased head motion and
possible injury to the child. Use only the anchor positions directly behind the child
seat to secure a child restraint top tether strap.

Installing The Child Restraint Using The Vehicle Seat Belts

• To install a child restraint, first, pull enough of the seat belt webbing from the retractor to
route it through the belt path of the child restraint and slide the latch plate into the
buckle.

• Next, extract all the seat belt webbing out of the retractor and then allow the belt to
retract into the retractor. Finally, pull on any excess webbing to tighten the lap portion
around the child restraint. Any seat belt system will loosen with time, so check the belt
occasionally, and pull it tight if necessary.

10

GETTING STARTED

• Once you have completed securing the child restraint with the seat belt, secure the top
tether strap. The tether strap should be routed over the center top of the head restraint.

WARNING!

Rearward-facing child seats must NEVER be used in the front seat of a vehicle with
a front passenger airbag. An airbag deployment could cause severe injury or death
to infants in this position.

FRONT SEATS

WARNING!

Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of
the seat could cause you to lose control. The seat belt might not be properly
adjusted, and you could be injured. Only adjust a seat while the vehicle is parked.

Manual Seat Adjustment

Forward/Rearward

• Lift up on the adjusting bar located at the
front of the seat near the floor and release at
the desired position.

11

GETTING STARTED

Recliner

• Lift the recliner lever located on the outboard
side of the seat, lean back and release at the
desired position.

Driver’s Seat Height Adjustment

• The height adjustment lever is located on the
outboard side of the seat. Raise the lever to
raise the seat. Lower the lever to lower the
seat.

Lumbar Support

• The lumbar lever is on the outboard side of
the seatback. Rotate the lumbar lever
downward to increase the lumbar support or
upward to decrease the lumbar support as

desired.

WARNING!

Do not ride with the seatback reclined so that the seat belt is no longer resting
against your chest. In a collision, you could slide under the seat belt and be seriously
or even fatally injured. Use the recliner only when the vehicle is parked.

Six-Way Power Seats

• The power seat switch is located on the

outboard side of the seat near the floor. Use
the switch to move the seat up, down,
forward, rearward, or to tilt the seat.

CAUTION!

DO NOT place any article under a power seat or impede its ability to move as it may
cause damage to the seat controls. Seat travel may become limited if movement is
stopped by an obstruction in the seat’s path.

12

GETTING STARTED

Heated Seats

• The controls for the front heated seats are

located on the center instrument panel area.

• Press the switch once to select High-level

heating. Press the switch a second time to
select Low-level heating. Press the switch a
third time to shut the heating elements Off.

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic
illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other
physical conditions must exercise care when using the seat heater. It may cause
burns even at low temperatures, especially if used for long periods of time.

• Do not place anything on the seat that insulates against heat, such as a blanket or
cushion. This may cause the seat heater to overheat. Sitting in a seat that has
been overheated could cause serious burns due to the increased surface
temperature of the seat.

CAUTION!

Repeated overheating of the seat could damage the heating element and/or degrade
the material of the seat.

Fold-Flat Front Passenger Seat

• The front passenger seat can be folded flat.
Pull up on the recliner handle, to the full
upward position, to fold down the seatback.

13

GETTING STARTED

REAR SEATS

Folding Rear Seatback

• To fold each rear seatback, pull the strap
forward to move the seatback forward and
flat.

Reclining Rear Seatback

• To recline each rear seatback, pull the strap
forward just enough to release the seatback
latch. Then push the seatback to a reclined
position, approximately 35 degrees
maximum, and release the strap.

TILT STEERING COLUMN

• The tilt lever is located on the steering
column, below the turn signal lever.

• Push down on the lever to unlock the steering
column.

• With one hand firmly on the steering wheel,
move the steering column up or down as
desired.

• Pull upward on the lever to lock the column
firmly in place.

WARNING!

Do not adjust the steering column while driving. Adjusting the steering column while
driving or driving with the steering column unlocked, could cause the driver to lose
control of the vehicle. Be sure the steering column is locked before driving your
vehicle. Failure to follow this warning may result in serious injury or death.

14

GETTING STARTED

PROGRAMMABLE FEATURES

Electronic Vehicle Information Center (EVIC) - If Equipped

• Press the EVIC button, located below the
speedometer, until Personal Settings is
displayed on the EVIC. Use the EVIC button to
select one of the following, then press and
hold the EVIC button to select either “ON” or
“OFF”.

• Language • Key-Off Power Delay

• Auto Door Locks • Display Units of Measure In

• Auto Unlock On Exit • Confirmation of Voice Commands

• Sound Horn With Remote Key Lock • Automatic Compass Calibration

• Illuminated Approach • Compass Variance

• Headlamp Off Delay • Manual Compass Calibration

• RKE Unlock (Remote Key Unlock)
Driver’s Door 1st

Key Fob Programmable Features

• The following features may also be programmed using the Key Fob transmitter or the
ignition switch and driver's door lock switch.

NOTE: Pressing the LOCK button while you are inside the vehicle will activate the Vehicle
Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the
alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.

• Flash Lamps With Lock (Flashing
Lights with Remote Key Lock)

Unlock On First Press

• To unlock either the driver's side, or all doors, on the first press of the UNLOCK button:

• Press and hold the LOCK button for at least 4 seconds, but no longer than 10 seconds.
Then, press and hold the UNLOCK button while still holding the LOCK button.

• Release both buttons at the same time.

Auto Unlock Doors On Exit

• To have all of the vehicle doors unlock when any door is opened:

• Enter your vehicle and close all the doors.

• Within 15 seconds, cycle the ignition switch from the LOCK position to the ON position
a minimum of four times, ending in the LOCK position (do not start the engine).

• Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. A
single chime will indicate that programming is complete.

15

GETTING STARTED

Auto Door Lock

• To have the doors lock automatically when the vehicle’s speed exceeds 15 mph
(24 km/h):

• Enter your vehicle and close all the doors.

• Within 15 seconds, cycle the ignition switch from the LOCK position to the ON position
a minimum of four times, ending in the LOCK position (do not start the engine).

• Within 30 seconds, press the driver’s door lock switch in the LOCK direction. A single
chime will indicate that programming is complete.

Sound Horn With Lock

• To turn the horn chirp on or off when the doors are locked:

• Press the LOCK button for at least 4 seconds, but no longer than 10 seconds. Then,
press the PANIC button while still holding the LOCK button.

• Release both buttons at the same time.

Flashing Lights With Lock

• The turn signal lights flashing, when the doors are locked or unlocked, feature can be
turned on or off. To turn this feature on or off:

• Press and hold the UNLOCK button for at least 4 seconds, but no longer than
10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK
button.

• Release both buttons at the same time.

16

OPERATING YOUR VEHICLE

TURN SIGNAL/LIGHTS LEVER

Headlights/Parking Lights

• Rotate the end of the lever to the first detent for parking lights and to the second
detent for headlights

Instrument Panel Dimmer

• Rotate the center portion of the lever to the extreme bottom position to fully dim the
instrument panel lights and prevent the interior lights from illuminating when a door is
opened.

• Rotate the center portion of the lever up to increase the brightness of the instrument
panel lights when the parking lights or headlights are on.

• Rotate the center portion of the lever upward to the next detent position to brighten the
odometer and radio controls when the parking lights or headlights are on.

• Rotate the center portion of the lever upward to the last detent to turn on the interior
lighting.

Flash To Pass

• Pull the lever toward you to activate the high beams. The high beams will remain on until
the lever is released.

High Beam Operation

• Push the lever forward to activate the high beams.

NOTE: For safe driving, turn off high beams when oncoming traffic is present to prevent
headlight glare and as a courtesy to other motorists.

Fog Lights

• Turn on the parking lights or low beam headlights and pull out the end of the lever.

.

17

OPERATING YOUR VEHICLE

Turn Signals/Lane Change Assist

• Tap the lever up or down once and the turn signal (right or left) will flash three times and
automatically turn off.

WIPER/WASHER LEVER

Front Wipers

Intermittent, Low And High Operation

• Rotate the end of the lever to the first detent position for one of five intermittent settings,
the second detent for low wiper operation and the third detent for high wiper operation.

Washer Operation

• Pull the lever toward you and hold for as long as spray is desired.

Mist

• Pull down on the lever and release when a single wipe is desired.

Rear Wiper

Wiper Operation

• Rotate the center portion of the lever forward to the first detent for rear wiper operation.

Washer Operation

• Rotate the center portion of the lever past the first detent to activate the rear washer.

18

OPERATING YOUR VEHICLE

SPEED CONTROL LEVER

Cruise ON/OFF

• Push the ON/OFF button to activate the Speed
Control.

• CRUISE will appear on the instrument cluster
to indicate the Speed Control is on.

• Push the ON/OFF button a second time to
turn the system off.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You
could accidentally set the system or cause it to go faster than you want. You could
lose control and have an accident. Always leave the Electronic Speed Control system
off when you are not using it.

Set

• With Speed Control on, push down and release the lever to set a desired speed.

WARNING!

Electronic Speed Control can be dangerous where the system cannot maintain a
constant speed. Your vehicle could go too fast for the conditions, and you could lose
control. An accident could be the result. Do not use Electronic Speed Control in
heavy traffic or on roads that are winding, icy, snow-covered or slippery.

Accel/Decel

• Push and hold the lever up to accelerate or down to decelerate the vehicle; release the
lever to save the new set speed.

• Once a speed is set, tapping the lever up or down will increase or decrease the set speed
approximately 1 mph (2 km/h).

Cancel

• Pull the lever toward you, push the clutch pedal or apply the brakes to cancel the set
speed and maintain the set speed in memory.

• Push the ON/OFF button to turn the system off and erase the set speed memory.

Resume

• To resume a previously selected speed in memory, push the lever up and release.

19

OPERATING YOUR VEHICLE

CONTINUOUSLY VARIABLE AUTOMATIC TRANSMISSION (CVT)

• While conventional automatic transmissions typically have 4, 5 or 6 speeds, the
Continuously Variable Transmission (CVT) has an infinite number of speeds. This allows
it to adjust to exactly the right ratio to optimize performance and fuel economy.

• Under hard acceleration, you may hear more engine noise than with a conventional
transmission. The CVT may also occasionally feel like it is “shifting.” These
characteristics are perfectly normal and contribute to the CVT's efficiency.

MANUAL CLIMATE CONTROLS

Air Recirculation

• Use recirculation for maximum A/C operation.

• For window defogging, turn the recirculation button off.

• Recirculation is not allowed in defrost, floor, defrost/floor (mix) modes.

20

OPERATING YOUR VEHICLE

AUTOMATIC TEMPERATURE CONTROLS (ATC)

Automatic Operation

• Turn the Mode and Blower Controls to the AUTO position.

• Select the desired temperature by rotating the Temperature Control.

• The system will maintain the set temperature automatically.

Air Conditioning

• If the air conditioning button is pressed while in the AUTO mode, the indicator light may
flash three times to indicate the cabin air is being controlled automatically.

Air Recirculation

• Use recirculation for maximum A/C operation.

• For window defogging, turn the air recirculation button off.

• If the recirculation button is pressed while in the AUTO mode, the indicator light may
flash three times to indicate the cabin air is being controlled automatically.

POWER SUNROOF

• The power sunroof switch is located on the overhead console.

WARNING!

• Never leave children in a vehicle with the key in the ignition switch. Occupants,
particularly unattended children, can become entrapped by the power sunroof
while operating the power sunroof switch. Such entrapment may result in serious
injury or death.

• In an accident, there is a greater risk of being thrown from a vehicle with an open
sunroof. You could also be seriously injured or killed. Always fasten your seat belt
properly and make sure all passengers are properly secured too.

(Continued)

21

OPERATING YOUR VEHICLE

WARNING! (Continued)

• Do not allow small children to operate the sunroof. Never allow your fingers, other
body parts, or any object to project through the sunroof opening. Injury may result.

Opening Sunroof

Express

• Press the switch rearward and release. The sunroof will fully open and stop
automatically.

Closing Sunroof

Express

• Press the switch forward and release. The sunroof will close automatically from any
position.

Manual Open/Close

• Press and hold the switch rearward to open or forward to close the sunroof. Any release
of the switch will stop the movement, and the sunroof will remain in a partially open or
closed position until the switch is pressed again.

Venting Sunroof

• Press and release the "VENT" button, and the sunroof will open to the vent position. This
is called “Express Vent” and will occur regardless of sunroof position. During Express
Vent operation, any movement of the switch will stop the sunroof.

Pinch Protection Feature

• This feature will detect an obstruction in the opening of the sunroof during Express Close
operation. If an obstruction in the path of the sunroof is detected, the sunroof will
automatically return to the open position.

NOTE: Pinch protection is disabled while the switch is pressed and held during manual
opening and closing of the sunroof.

WIND BUFFETING

• Wind buffeting can be described as a helicopter-type percussion sound. If buffeting
occurs with the rear windows open, adjust the front and rear windows together.

• If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any
window. This will minimize buffeting.

22

NON-TOUCH-SCREEN RADIOS

Sales Code RES

ELECTRONICS

Sales Code RES/RSC

23

ELECTRONICS

Sales Code REQ

NOTE: Uconnect™ Phone and Voice Command are vehicle options which must be ordered
separately. The buttons on the radio will only be active if the vehicle has been equipped with
the option.

• The radio sales code is located on the lower right side of the radio faceplate.

• Unless otherwise noted, the information provided on the operation and functionality of
the radios in this section is common to all non-touch-screen radios.

Seek Up/Down Buttons

• Press to seek through radio stations in AM, FM or SAT bands. Seek through tracks in CD.

• Holding either button will bypass stations without stopping.

Audio Settings

• Press the TUNE/SCROLL control knob and BASS, MID, TREBLE, BALANCE and FADE will
display. Rotate the TUNE/SCROLL control knob to select the desired setting.

Auxiliary Mode

• The auxiliary (AUX) jack allows a portable device, such as an MP3 player or a cassette
player, to be plugged into the radio and utilize the vehicle’s audio system to amplify the
source and play through the vehicle speakers.

• Pressing the AUX button will change the mode to auxiliary device if the AUX jack is
connected.

24

ELECTRONICS

• The control of the external device cannot be provided by the radio; use the device controls
instead.

Clock Setting

• Press and hold the TIME button until the hours blink; turn the TUNE/SCROLL control
knob to set the hours.

• Press the TUNE/SCROLL control knob until the minutes begin to blink; turn the
TUNE/SCROLL control knob to set the minutes.

• Press the TUNE/SCROLL control knob to save the time change.

• To exit, press any button/knob or wait five seconds.

Station Presets

• Press the SET/RND button once and SET 1 will show in the display. Then select the button
(1–6).

• A second station may be added to each push button. Press the SET/RND button twice and
SET 2 will show in the display, then select button (1–6).

How To Load Multiple CDs/DVDs

REQ Radio Only

• Press the LOAD button and then press the button with the corresponding number (1–6)
where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to
INSERT DISC.

• After the radio displays INSERT DISC, insert the CD into the player. The radio display will
show LOADING DISC when the disc is loading and “READING DISC” when the radio is
reading the disc.

• Press the eject button and then the corresponding number (1–6) to eject the desired disc.

25

ELECTRONICS

TOUCH-SCREEN RADIOS

Multimedia Radio – Sales Code REN

Navigation Radio – Sales Code RER

26

ELECTRONICS

Multimedia Radio – Sales Code RBZ

NOTE: Uconnect™ Phone and Voice Command are vehicle options which must be ordered
separately. The buttons on the radio will only be active if the vehicle has been equipped with
the option.

• The radio sales code is located on the lower right side of the radio faceplate.

• Unless otherwise noted, the information provided on the operation and functionality of
the radios in this section is common to all touch-screen radios.

Seek Up/Down

• REN and RER Radios – Press the SEEK hard-key to seek through radio stations in AM,
FM, or SAT bands. Seek through tracks in CD or iPod® modes or through songs in the
HDD playlist.

• RBZ Radio – Touch the SCAN soft-key, right or left arrow soft-keys to change the
currently playing station in AM, FM or SAT bands.

Auxiliary Mode

• The auxiliary (AUX) jack allows a portable device, such as an MP3 player or a cassette
player, to be plugged into the radio and utilize the vehicle’s audio system and play
through the vehicle speakers.

Clock Setting

• Turn the radio on, then touch the screen where the time is displayed.

• Touch the USER CLOCK soft-key (Navigation radio only).

27

ELECTRONICS

• To adjust the hours, touch either the HOUR FORWARD or HOUR BACKWARD soft-key.

• To adjust the minutes, touch either the MINUTE FORWARD or MINUTE BACKWARD
soft-key.

• To save the new time setting, touch the screen where the word “Save” is displayed.

Store Radio Presets

• For REN and RER: Press the RADIO/MEDIA hard-key repeatedly until AM FM SAT is
displayed in the upper left corner of the screen.

• For RBZ: Press the RADIO hard-key to display AM FM SAT in the upper left corner of the
screen.

• Select the radio band by touching either the AM, FM, or SAT soft-key.

• Find the station to store by either pressing the SEEK UP/DOWN hard-key (REN and RER),
touching the right and left arrow soft-keys (RBZ), touching the SCAN soft-key, or by using
the DIRECT TUNE soft-key.

• Once the station is found, touch and hold one of the PRESET soft-keys in the list to the
right, until you hear a confirmation beep.

Hard Disk Drive Operation

Copy Complete Audio Disc To Hard-Drive

• Press the OPEN/CLOSE hard-key (REN and RER) or LOAD hard-key (RBZ) and insert a
disc, then press the MENU hard-key.

• Touch the MY FILES soft-key, then select MY MUSIC.

• Touch the IMPORT MUSIC soft-key, then touch the FROM DISC soft-key in the next screen
to start the process.

Copying From USB

• Insert a USB device, then select MY MUSIC.

• Touch the IMPORT MUSIC FILES soft-key, then touch the FROM USB soft-key in the next
screen.

• Select the folders or titles you would like to copy, then touch the DONE soft-key to start
the copy process.

Copy Pictures To The Hard-Drive

• Insert either a CD or a USB device containing your pictures.

• Touch the MY FILES soft-key, then go to the MANAGE MY FILES screen.

• Touch the MY PICTURES soft-key to get an overview of the currently stored images.

• Touch one of the ADD PICTURES soft-keys, then select the type of media inserted.

• Use the PAGE soft-keys to page through a list of pictures and press the picture you would
like to import.

• Confirm your selection by touching the YES soft-key. The imported picture is now
available in the MANAGE MY PICTURES screen.

28

ELECTRONICS

• In order to display the imported picture in the radio screen, touch the desired picture
soft-key.

• Select this picture by pressing the PICTURE VIEW soft-key. A check mark indicates the
currently used picture.

Cleaning Your Touch-Screen Radio

• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry
micro fiber lens cleaning cloth in order to clean the touch-screen.

• If necessary, use a lint-free cloth dampened with a cleaning solution such as isopropyl
alcohol or an isopropyl alcohol and water solution ratio of 50:50. Be sure to follow the
solvent manufacturer's precautions and directions.

Navigation

Navigation Radio – RER Only

• Navigation radios require digital data from a navigation database. The data in the
navigation database is licensed from Navigation Technologies®. Not all roads are
digitized.

• For software updates, visit http://www.chrysler.com/en/owners/mygig/ website, visit
http://www.navteq.com website, or contact your authorized dealer for the latest available
software.

NOTE: Many features of this radio are speed dependent. For your own safety, it is not
possible to use the touch-screen keyboard to enter a name (e.g., street name) while the
vehicle is in motion. Pull over at a safe location to complete your task.

• The Navigation system receives GPS signals from satellites to display the position of your
vehicle.

New Destination

• Press the NAV hard-key to access the Navigation Main Menu.

• Touch the NEW DESTINATION soft-key to program a destination, then select the
destination soft-key of your choice.

Program/Storing Home Address

• Press the NAV hard-key to access the Navigation Main Menu.

• Touch the GUIDE ME HOME soft-key, then touch the STREET ADDRESS soft-key.

• Touch the STATE soft-key, then enter your state name into the speller; select your state
from the list and press the CHANGE soft-key.

• Touch the INPUT STREET NAME soft-key and enter your street name into the speller.

• Touch the CONTINUE soft-key and enter your address into the speller; touch the
CONTINUE soft-key again.

• Touch the city name and touch the SAVE soft-key to complete programming.

29

ELECTRONICS

Change Stored Home Address

• Press the MENU hard-key, then touch the MY FILES soft-key.

• Touch the MY ADDRESS BOOK soft-key, then touch the HOME soft-key.

• In the Home Address Information screen, touch the EDIT CONTACT soft-key, then touch
the CHANGE ADDRESS soft-key in the next screen.

• Touch the INPUT STREET NAME soft-key and enter your street name into the speller.

• Touch the CONTINUE soft-key and enter your address into the speller; touch the
CONTINUE soft-key again.

• Touch the city name and touch the SAVE soft-key to complete programming.

Guide Me Home

• Press the NAV hard-key to access the Navigation Main Menu.

• Touch the GUIDE ME HOME soft-key to route you back to your home destination from
your current location. Touch the GO soft-key to start your trip.

Map

• Press the NAV hard-key to access the Navigation Main Menu.

• Touch the MAP soft-key to display a map of your current position.

REMOTE AUDIO CONTROLS

• The remote audio controls are located on the
rear surface of the steering wheel.

Right Switch

• Press the switch up or down to increase or
decrease the volume.

• Press the button in the center to change
modes AM/FM/CD/SAT.

Left Switch

• Press the switch up or down to search for the
next listenable station or select the next or
previous CD track.

• Press the button in the center to select the next preset station (radio) or to change CDs if
equipped with a CD Changer.

30

ELECTRONICS

UNIVERSAL CONSUMER INTERFACE

• This feature allows you to plug an iPod® into
the vehicle’s sound system through a 16–pin
connector using the provided interface cable.

• The 16–pin connector port is located in the
glove box or on the center console. Location
may vary. To get into the UCI (iPod®) mode
from a non-touch-screen radio, press the
AUX button on the radio faceplate. From
touch-screen radios, press the MEDIA
hard-key, then touch the iPod® soft-key.
When connected to this feature:

• The iPod® audio can be played on the vehicle’s sound system.

• The iPod® can be controlled using the radio buttons to Play, Browse, and List the iPod®
contents. Refer to the Owner's Manual on the DVD for details.

• The iPod® battery charges when plugged into the UCI connector.

WARNING!

Do not plug in or remove the iPod® while driving. Failure to follow this warning
could result in an accident.

ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)

• The EVIC features a driver interactive display
that is located in the instrument cluster. For
additional information, refer to
Programmable Features in this guide.

• Press the EVIC button, located below the
speedometer, until one of the following
functions is displayed on the EVIC:

• Compass/Temperature/Audio

• Average Fuel Economy

• Distance To Empty (DTE)

• Elapsed Time

• Tire Pressure Monitor (TPM)

• Personal Settings

• Pressing and holding the EVIC button once will clear the function currently being
displayed.

• To reset all resettable functions, press and release the EVIC button a second time within
three seconds of resetting the currently displayed function. Reset ALL will be displayed
during this three-second window.

31

ELECTRONICS

UNIVERSAL GARAGE DOOR OPENER

Programming HomeLink®

Begin Programming

• The HomeLink® buttons are located in the
headliner.

• Erase all channels before you begin training
by holding the two outside buttons for up to
20 seconds until the red indicator flashes.

• Park your vehicle outside of the garage and
turn the ignition switch to the ON/RUN
position.

• Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink® buttons while
keeping the indicator light in view.

• Simultaneously, press and hold both the chosen HomeLink® button and the handheld
transmitter button until the HomeLink® indicator flash rate changes from a slow to a
rapidly blinking light, then release both the HomeLink® and the handheld transmitter
buttons. This may take up to 30 seconds, or longer in rare cases.

• Press and hold the just-trained HomeLink® button; if the indicator light stays on
constantly, programming is complete and the garage door should open.

WARNING!

• Your motorized door or gate will open and close while you are training the
universal transceiver. Do not train the transceiver if people or pets are in the path
of the door or gate. Only use this transceiver with a garage door opener that has a
“stop and reverse” feature as required by Federal safety standards. This includes
most garage door opener models manufactured after 1982. Do not use a garage
door opener without these safety features. Call toll-free 1–800–355–3515 or, on
the Internet, at www.HomeLink.com for safety information or assistance.

• Vehicle exhaust contains Carbon Monoxide (CO), a dangerous gas. Do not run your
vehicle in the garage while training the transceiver. Exhaust gas can cause serious
injury or death.

NOTE: If you are having difficulty training your HomeLink® and your garage door opener
was manufactured after 1995, you may have a rolling code. Follow the steps below for
Programming A Rolling Code System.

Programming A Rolling Code System

• At the garage door opener motor (in the garage), locate the “learn” or “training” button.
This can usually be found where the hanging antenna wire is attached to the garage door
opener motor (it is not the button normally used to open and close the door).

32

ELECTRONICS

• Firmly press and release the “learn” or “training” button then, within 30 seconds, return
to the vehicle and press the programmed HomeLink® button twice (holding the button
for two seconds each time). If the device is plugged in and activates, programming is
complete.

• If the device does not activate, press the button a third time (for two seconds) to complete
the training.

Using HomeLink®

• To operate, simply press and release the programmed HomeLink® button and the
trained device will operate.

• Refer to your Owner’s Manual on the DVD for further details. If you have any problems
programming HomeLink®, or require assistance, please call toll-free 1–800–355–3515
or, on the Internet, at www.HomeLink.com.

POWER INVERTER

• A 115 Volt, 150 Watt AC power inverter is
located on the front of the center console.

• This outlet can power cellular phones,
electronics and other low power devices
requiring power up to 150 Watts.

NOTE: The power inverter is designed with built-in overload protection. If the power
rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the
electrical device has been removed from the outlet, the inverter should automatically reset.
If the power rating exceeds approximately 170 Watts, the power inverter may have to be
reset manually. To reset the inverter manually, unplug the device and plug it in again. To
avoid overloading the circuit, check the power ratings on electrical devices prior to using
the inverter.

WARNING!

To avoid serious injury or death: Do not use a three-prong adaptor. Do not insert any
objects into the receptacles. Do not touch with wet hands. Close the lid when not in
use. If this outlet is mishandled, it may cause an electric shock and failure.

33

ELECTRONICS

POWER OUTLET

• The power outlet is located on the instrument panel below the climate control and is
powered when the ignition switch is in the ON position.

• The outlet can operate a conventional cigar lighter unit or power accessories designed
for use with a standard power outlet adapter.

NOTE: Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160
Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be
replaced.

Uconnect™ Phone

• The Uconnect™ Phone is a voice-activated, hands-free, in-vehicle communications
system.

• The Uconnect™ Phone allows you to dial a phone number with your cellular phone using
simple voice commands.

• For vehicles equipped with Video Entertainment System (VES)™, refer to the Uconnect™
Phone section of the Uconnect™ User's Manual on the DVD for further details.

• For vehicles not equipped with VES™, refer to your vehicle Owner's Manual on the DVD
for further details.

WARNING!

• Any voice commanded system should be used only in safe driving conditions
following local laws and phone use. All attention should be kept on the roadway
ahead. Failure to do so may result in an accident causing serious injury or death.

• Your phone must be turned on and paired to the Uconnect™ Phone to allow use of
this vehicle feature in emergency situations, when the cellular phone has network
coverage and stays paired to the Uconnect™ Phone.

NOTE: The Uconnect™ Phone requires a cellular phone equipped with the Bluetooth®
Hands-Free Profile, Version 0.96 or higher. For Uconnect™ customer support, call
1–877–855–8400.

Phone Pairing

NOTE: Pairing is a one-time initial setup before using the phone. You will also need to
follow the Bluetooth® instructions in your cell phone user guide to complete the phone
pairing setup.

• Press the Phone button

• Wait for the “ready” prompt and beep.

• (After the BEEP), say “Uconnect setup”.

• (After the BEEP), say “phone pairing”.

• (After the BEEP), say “pair a phone”.

• Follow the audible prompts.

to begin.

34

ELECTRONICS

• You will be asked to create a four-digit PIN which you will later need to enter into your
phone (typically...settings, Bluetooth®, device, list, new).

• You will then be prompted to give the phone pairing a name (each phone paired should
have a unique name).

• Next you will be asked to give this new pairing a priority of 1 thru 7 (up to seven phones
may be paired).

Making A Phone Call

• Press the Phone button .

• (After the BEEP), say “dial” (or “call” to a name).

• (After the BEEP), say number (or name).

Phonebook (Uconnect™ local) Edit

• Press the Phone button .

• (After the BEEP), say “phonebook”.

• (After the BEEP), say “new entry” or “list names” or “delete”.

• Follow the prompts.

Receiving A Call – Accept (And End)

• When an incoming call rings/is announced on Uconnect™, press the Phone button .

• To end a call, press the Phone button

.

Mute (Or Unmute) Microphone During Call

• During a call, press the Voice Command button .

• (After the BEEP), say “mute on” (or “mute off”).

Transfer Ongoing Call Between Handset And Vehicle

• During a call, press the Voice Command button .

• (After the BEEP), say “transfer call”.

Changing The Volume

• Start a dialogue by pressing the Phone button
normal call.

• Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level
while the Uconnect™ system is speaking. Please note the volume setting for Uconnect™
is different than the audio system.

NOTE: To access the tutorial, press the Uconnect™ hard-key. After the BEEP, say
“tutorial”. Press any hard-key or touch the display to cancel the tutorial.

35

, then adjust the volume during a

ELECTRONICS

VOICE COMMAND

• The Voice Command system allows you to control your AM, FM radio, satellite radio, disc
player, and a memo recorder. When you press the Voice Command button
will hear a beep. The beep is your signal to give a command. If you do not say a
command within a few seconds, the system will present you with a list of options. If you
ever wish to interrupt the system while it lists options, press the Voice Command
button

• For vehicles equipped with Video Entertainment System (VES)™, refer to the Voice
Command section of the Uconnect™ User's Manual on the DVD for further details.

• For vehicles not equipped with VES™, refer to your vehicle Owner's Manual on the DVD
for Voice Command information.

, listen for the BEEP, and say your command.

Changing The Volume

• Start a dialogue by pressing the Voice Command button , then say a command
(e.g., “tutorial”).

• Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level
while the Voice Command system is speaking. Please note the volume setting for Voice
Command is different than the audio system.

WARNING!

Any voice commanded system should be used only in safe driving conditions and all
attention should be kept on the roadway ahead. Failure to do so may result in an
accident causing serious injury or death.

,you

NOTE: To access the tutorial, press the Voice Command button
say “tutorial”. Press any hard-key or touch the display to cancel the tutorial.

36

. After the BEEP,

OFF-ROAD CAPABILITIES

FOUR-WHEEL DRIVE OPERATION

• This feature provides full time,
on-demand, four–wheel drive (4WD).

• To activate, pull the T-handle, located in
between the front driver and passenger
seats, up once and release. The “4WD
Indicator Light” will come on in the
cluster.

• This can be done on the fly, at any
vehicle speed. To deactivate, simply
pull on the T-handle one more time.
The “4WD Indicator Light” will then go
out.

37

UTILITY

Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. (See Note 1)

2.0L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 150 lbs (50 kg)

TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS)

Refer to local laws for maximum trailer towing speeds.

32 sq ft (3.0 sq m) 2,000 lbs (907 kg) 300 lbs (136 kg)

2.4L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 150 lbs (50 kg)

2.4L Auto/Man with

Trailer Tow Prep Package

(AHC)

Note1–Thetrailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never

exceed the weight referenced on the Tire and Loading Information placard.

38

UTILITY

RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)

Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground)

Recreational Towing
Condition

Four Wheel Flat Tow (All
Wheels on Ground)

Two Wheel Dolly Tow (Front
or Rear Wheels on Ground)

Flat Bed Tow (All Wheels
on Bed of Truck)

NOTE: Vehicles equipped with manual transaxles may be recreationally towed (flat towed)
at any legal highway speed, for any distance, if the manual transaxle is in NEUTRAL and the
ignition key is in the ACC position.

CAUTION!

• DO NOT flat tow any vehicle
equipped with an automatic
transaxle. Damage to the
drivetrain will result. If these
vehicles require towing, make sure
all four wheels are off the ground.

• Front or rear wheel lifts should not
be used. Internal damage to the
transaxle will occur if a front or
rear wheel lift is used when
recreational towing.

BRAKE/TRANSMISSION INTERLOCK MANUAL OVERRIDE SYSTEM

• The manual override may be used in
the event that the shift lever should fail
to move from PARK with the Key Fob in
the ON position and the brake pedal
pressed.

Manual Transaxle

Vehicles

Yes Never

Never Never

Yes Yes

• To operate the shift lock manual
override, perform the following steps:

• Locate and remove the removable
plug in the right side of the shift
lever housing.

• Turn the ignition switch to the ACC or
ON position without starting the
engine.

• Firmly set the parking brake.

• Press and maintain firm pressure
on the brake pedal.

• Using your finger, press and hold
the override tab through the access
port.

• Move the shift lever into the
NEUTRAL position and start the
vehicle.

• Reinstall the removable plug.

• Have your vehicle inspected by your
local authorized dealer if the shift lock
manual override has been used.

Automatic Transaxle

Vehicles

39

WHAT TO DO IN EMERGENCIES

24 HOUR TOWING ASSISTANCE - U.S. ONLY

• Dial toll-free 1-800-521-2779.

• Provide your name, vehicle identification number and license plate number.

• Provide your location, including telephone number, from which you are calling.

• Briefly describe the nature of the problem and answer a few simple questions.

• You will be given the name of the service provider and an estimated time of arrival. If you
feel you are in an “unsafe situation”, please let us know. With your consent, we will
contact local police or safety authorities.

INSTRUMENT CLUSTER WARNING LIGHTS

- Electronic Stability Control (ESC) Malfunction Indicator Light

• If the “ESC Malfunction Indicator Light” comes on continuously with the engine running, a
malfunction has been detected in the ESC system. If this light remains on after several
ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds
greater than 30 mph (48 km/h), we recommend you drive to the nearest service center as
soon as possible to have the problem diagnosed and corrected.

• The “ESC Malfunction Indicator Light” starts to flash as soon as the tires lose traction and
the ESC system becomes active. If the light begins to flash during acceleration, ease up
on the accelerator and apply as little throttle as possible. Be sure to adapt your speed
and driving to the prevailing road conditions. The light also flashes when TCS is active. To
improve the vehicle's traction when starting off in deep snow, sand or gravel, it may be
desirable to switch the ESC system to Partial Off mode by momentarily pressing the ESC

switch.

Off

- Tire Pressure Monitoring System (TPMS) Light

• A Tire Pressure Monitoring Light and a “low tire” message will display in your instrument
cluster along with an audible chime if one or more of your vehicle’s four road tires are
significantly under-inflated.

• Check the inflation pressure of each tire and inflate to the recommended pressure for
your vehicle. The tire pressures recommended for your vehicle are found on the “Tire and
Loading Information” label located on the driver’s side door opening. The TPMS light
should not be used as a tire pressure gauge when adjusting your tire pressure.

• It is recommended that you check the tire pressure in the morning when tires are cool;
inflate each tire to the recommended pressure for your vehicle. The light will turn off
after your vehicle’s tire pressures are properly inflated and the pressure has been
recognized. The vehicle may need to be driven for up to 20 minutes above 15 mph
(25 km/h) before the light will turn off.

• Temperature changes can affect tire pressure, causing the TPMS light to turn on. Tire
pressures will also increase as the vehicle is driven – this is normal and you should not
adjust for this increased pressure.

• Driving on under-inflated tires reduces your vehicle’s fuel efficiency and tire tread life. If a
spare tire is in use on the vehicle, the TPMS light may turn on.

40

WHAT TO DO IN EMERGENCIES

- Engine Temperature Warning Light

• This light warns of an overheated engine condition.

• If the light turns on and a warning chime sounds while driving, safely pull over and stop
the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL
and idle the vehicle. If the temperature reading does not return to normal, turn the
engine off immediately.

• We recommend that you do not operate the vehicle or engine damage will occur. Have
the vehicle serviced immediately.

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by
steam or boiling coolant. You may want to call an authorized dealership for service if
your vehicle overheats.

BRAKE

• The Brake Warning light illuminates when there is either a system malfunction or the

• We recommend you drive to the nearest Service Center and have the vehicle serviced

- Brake Warning Light

parking brake is applied. If the light is on and the parking brake is not applied, it
indicates a possible brake hydraulic malfunction, brake booster problem or an Anti-Lock
Brake System problem.

immediately.

WARNING!

Driving a vehicle with the red brake light on is dangerous. Part of the brake system
may have failed. It will take longer to stop the vehicle. You could have an accident.
Have the vehicle checked immediately.

- Malfunction Indicator Light (MIL)

• Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may
illuminate the MIL after engine start. The vehicle should be serviced if the light stays on
through several typical driving cycles. In most situations, the vehicle will drive normally
and not require towing.

• If the MIL flashes when the engine is running, serious conditions may exist that could
lead to immediate loss of power or severe catalytic converter damage. We recommend
you do not operate the vehicle. Have the vehicle serviced as soon as possible if this
occurs.

- Charging System Light

• This light shows the status of the electrical charging system. If the charging system light
remains on, it means that the vehicle is experiencing a problem with the charging
system.

41

WHAT TO DO IN EMERGENCIES

• We recommend you do not continue driving if the charging system light is on. Have the
vehicle serviced immediately.

- Oil Pressure Warning Light

• This light indicates low engine oil pressure. If the light turns on while driving, stop the
vehicle and shut off the engine as soon as possible. A chime will sound for four minutes
when this light turns on.

• We recommend you do not operate the vehicle or engine damage will occur. Have the
vehicle serviced immediately.

- Anti-Lock Brake (ABS) Light

• This light monitors the Anti-Lock Brake System (ABS).

• If the light is not on during starting, stays on, or turns on while driving, we recommend
you drive to the nearest Service Center and have the system serviced as soon as
possible.

- Electronic Throttle Control (ETC) Light

• This light informs you of a problem with the Electronic Throttle Control (ETC) system.

• If a problem is detected, the light will come on while the engine is running. Cycle the
ignition when the vehicle has completely stopped and the shift lever is placed in the
PARK position; the light should turn off.

• If the light remains lit with the engine running, your vehicle will usually be drivable;
however, see an authorized dealer for service as soon as possible. If the light is flashing
when the engine is running, immediate service is required and you may experience
reduced performance, an elevated/rough idle or engine stall and your vehicle may
require towing.

- Airbag Warning Light

• If the light is not on during starting, stays on, or turns on while driving, we recommend
you drive to the nearest Service Center and have the system serviced as soon as
possible.

- 4WD System Fault Indicator Light

• When lit solid: There is a 4WD system fault. The 4WD performance will be at a reduced
level. Drive to the nearest Service Center and have the vehicle serviced as soon as
possible.

• When blinking: The 4WD system is temporarily disabled due to overload condition.

- Transmission Temperature Warning Light

• This light indicates that there is excessive transmission fluid temperature that might
occur with severe usage such as trailer towing. If this light turns on, you will experience
reduced vehicle performance until the automatic transaxle cools down. If the overheating
continues, stop the vehicle and run the engine at idle, with the transmission in NEUTRAL,
until the light turns off. Once the light turns off, you may continue to drive normally.

42

WHAT TO DO IN EMERGENCIES

Fuel Cap/Loose Gas Cap Message

• If a “gas cap” message (shown as gASCAP) appears, tighten the gas cap until a “clicking”
sound is heard.

• Press the odometer reset button, located below the tachometer, to turn the message off.

• If the message continues to appear for more than three days after tightening the gas cap,
see your authorized dealer.

Oil Change Indicator

Message

• If an “oil change” message (shown as CHAngE OIL) appears and a single chime sounds,
it is time for your next required oil change.

Resetting The Light After Servicing

• Turn the ignition switch to the ON/RUN position (do not start engine).

• Fully depress the accelerator pedal three times within 10 seconds.

• Turn the ignition switch to the OFF/LOCK position.

IF YOUR ENGINE OVERHEATS

• In any of the following situations, you can reduce the potential for overheating by taking
the appropriate action.

• On the highways — slow down.

• In city traffic — while stopped, shift transmission into NEUTRAL, but do not increase
engine idle speed.

NOTE: There are steps that you can take to slow down an impending overheat condition:

• If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine
cooling system and turning the A/C off can help remove this heat.

• You can also turn the Temperature Control to maximum heat, the Mode Control to floor
and the Fan Control to high. This allows the heater core to act as a supplement to the
radiator and aids in removing heat from the engine cooling system.

• If the temperature reading does not return to normal, turn the engine off immediately.

• We recommend that you do not operate the vehicle or engine damage will occur. Have
the vehicle serviced immediately.

CAUTION!

Driving with a hot cooling system could damage your vehicle. If the temperature
gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air
conditioner turned off until the pointer drops back into the normal range. If the
pointer remains on HOT (H), and you hear continuous chimes, turn the engine off
immediately and call for service.

43

WHAT TO DO IN EMERGENCIES

WARNING!

You or others can be badly burned by hot engine coolant (antifreeze) or steam from
your radiator. If you see or hear steam coming from under the hood, do not open the
hood until the radiator has had time to cool. Never try to open a cooling system
pressure cap when the radiator or coolant bottle is hot.

AUTOMATIC TRANSAXLE OVERHEATING

• During sustained high speed driving or trailer towing up long grades on hot days, the
automatic transaxle oil may become too hot.

• When the transaxle overheat warning light
performance until the automatic transaxle cools down. Once the transaxle has cooled
down and the light turns off, you may continue to drive normally. If the high speed is
maintained, the overheating will continue to occur.

• If the overheating continues, it may become necessary to stop the vehicle and run the
engine at idle with the transaxle in NEUTRAL until the light turns off.

JACKING AND TIRE CHANGING

WARNING!

• Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Pull far enough off the road to avoid the danger of being hit when operating the
jack or changing the wheel.

• Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack
and fall on you. You could be crushed. Never get any part of your body under a
vehicle that is on a jack. If you need to get under a raised vehicle, take it to a
service center where it can be raised on a lift.

• The jack is designed to use as a tool for changing tires only. The jack should not
be used to lift the vehicle for service purposes. The vehicle should be jacked on a
firm, level surface only. Avoid ice or slippery areas.

turns on, you will experience reduced

WARNING!

• The compact spare tire is for emergency use only. Installation of this compact
spare tire affects vehicle handling.

• Do not drive more than 50 mph (80 km/h) with a compact spare tire.

• Keep the compact spare tire inflated to the cold tire inflation pressure, listed on
either your tire placard or limited use spare tire and wheel assembly.

• Replace (or repair) the original tire at the first opportunity and reinstall it on your
vehicle. Failure to do so could result in loss of vehicle control.

(Continued)

44

WHAT TO DO IN EMERGENCIES

WARNING! (Continued)

• A loose tire or jack, thrown forward in a collision or hard stop, could endanger the
occupants of the vehicle. Always stow the jack parts and spare tire in the places
provided.

Jack Location

• The jack and jack-handle are stowed under
the load floor in the trunk.

Spare Tire Stowage

• The compact spare tire is stowed under the
rear load floor in the trunk.

• To remove the spare tire, lift up the load floor
cover and remove the hold down.

Preparations For Jacking

• Park on a firm, level surface. Avoid ice or
slippery areas.

WARNING!

Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull
far enough off the road to avoid being hit when operating the jack or changing the
wheel.

• Set the parking brake and shift the automatic transmission into PARK, or a manual
transmission into REVERSE.

• Turn the ignition to LOCK and turn on the Hazard Warning flasher.

• Block both the front and rear of the wheel
diagonally opposite of the jacking position.
For example, if changing the right front tire,
block the left rear wheel.

NOTE: Passengers should not remain in the
vehicle when the vehicle is being jacked.

45

WHAT TO DO IN EMERGENCIES

Jacking And Tire Changing Instructions

WARNING!

Carefully follow these tire changing procedures to help prevent personal injury or
damage to your vehicle: Always park on a firm, level surface as far from the edge of
the roadway as possible before raising the vehicle.

• Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the
jack screw to the left to loosen the lug wrench, and remove the wrench from the jack
assembly.

NOTE: The jack handle attaches to the side of the jack with two attachment points. When
the jack is partially expanded, the tension between the two attachment points holds the jack
handle in place.

• Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while
the wheel is still on the ground.

• Assemble the jack and jacking tools. Connect the jack handle driver to the extension,
then to the lug wrench.

• Place the jack underneath the lift area (triangular cutout) that is closest to the flat tire.
Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill
flange.

• Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire
just clears the surface and enough clearance is obtained to install the spare tire.

46

WHAT TO DO IN EMERGENCIES

WARNING!

Raising the vehicle higher than necessary can make the vehicle less stable and
cause an accident. It could slip off the jack and hurt someone near it. Raise the
vehicle only enough to remove the tire.

• Remove the lug nuts, wheel cover (if equipped) and wheel.

• Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped
end toward the wheel. Do NOT attempt to install a center cap or wheel cover on the
compact spare. Lightly tighten the lug nuts clockwise. To avoid the risk of forcing the
vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered.

• Lower the vehicle by turning the jack screw to the left, and remove the jack and wheel
blocks.

• Finish tightening the lug nuts. Push down on the wrench while tightening for increased
leverage. Alternate nuts until each one has been tightened twice. The correct wheel nut
tightness is 100 ft lbs (135 N•m). If in doubt about the correct tightness, have them
checked with a torque wrench by your authorized dealer or at a service station.

WARNING!

A loose tire or jack, thrown forward in a collision or hard stop, could endanger the
occupants of the vehicle. Always stow the jack parts and the spare tire in the places
provided.

• Secure the tire, jack, and tools in their proper locations.

JUMP-STARTING

• If your vehicle has a discharged battery it can be jumpstarted using a set of jumper
cables and a battery in another vehicle or by using a portable battery booster pack.

• Jump-starting can be dangerous if done improperly so please follow the procedures in
this section carefully.

NOTE: When using a portable battery booster pack follow the manufacturer’s operating
instructions and precautions.

CAUTION!

Do not use a portable battery booster pack or any other booster source with a
system voltage greater than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

47

WHAT TO DO IN EMERGENCIES

WARNING!

When temperatures are below the freezing point, electrolyte in a discharged battery
may freeze. Do not attempt jump-starting because the battery could rupture or
explode and cause personal injury. Battery temperature must be brought above the
freezing point before attempting a jump-start.

Preparations for Jump-Start

• The battery in your vehicle is located in the front of the engine compartment below the air
intake duct. To access the battery remove the air intake duct by turning the two finger
screws, located on the radiator support.

WARNING!

• Take care to avoid the radiator cooling fan whenever the hood is raised. It can start
anytime the ignition switch is on. You can be injured by moving fan blades.

• Remove any metal jewelry such as watch bands or bracelets that might make an
inadvertent electrical contact. You could be seriously injured.

(Continued)

48

WHAT TO DO IN EMERGENCIES

WARNING! (Continued)

• Batteries contain sulfuric acid that can burn your skin or eyes and generate
hydrogen gas which is flammable and explosive. Keep open flames or sparks
away from the battery.

• Set the parking brake, shift the automatic transmission into PARK and turn the ignition to
LOCK.

• Turn off the heater, radio, and all unnecessary electrical accessories.

• If using a another vehicle to jump-start the battery, park the vehicle within the jumper
cables reach, set the parking brake and make sure the ignition is OFF.

WARNING!

Do not allow vehicles to touch each other as this could establish a ground
connection and personal injury could result.

Jump-Starting Procedure

WARNING!

Failure to follow this procedure could result in personal injury or property damage
due to battery explosion.

CAUTION!

Failure to follow these procedures could result in damage to the charging system of
the booster vehicle or the discharged vehicle.

• Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged
vehicle.

• Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the
booster battery.

• Connect the negative end (-) of the jumper cable to the negative (-) post of the booster
battery.

• Connect the opposite end of the negative (-) jumper cable to a good engine ground
(exposed metal part of the discharged vehicle’s engine) away from the battery and the
fuel injection system.

WARNING!

Do not connect the cable to the negative post (-) of the discharged battery. The
resulting electrical spark could cause the battery to explode and could result in
personal injury.

49

WHAT TO DO IN EMERGENCIES

• Start the engine in the vehicle that has the booster battery, let the engine idle a few
minutes, and then start the engine in the vehicle with the discharged battery.

• Once the engine is started, remove the jumper cables in the reverse sequence:

• Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the
discharged battery.

• Disconnect the negative end (-) of the jumper cable from the negative (-) post of the
booster battery.

• Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of
the booster battery.

• Disconnect the positive (+) end of the jumper cable from the positive (+) post of the
discharged vehicle.

• Reinstall the air intake duct.

• If frequent jump-starting is required to start your vehicle you should have the battery and
charging system inspected at your authorized dealer.

CAUTION!

Accessories that can be plugged into the vehicle power outlets draw power from the
vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if
plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade
battery life and/or prevent the engine from starting.

50

WHAT TO DO IN EMERGENCIES

Rear Wheels Raised,

Front Wheels on the

Ground

Front Wheels Raised,

Rear Wheels on the

Ground

Flatbed Towing (all

four wheels suspended

OFF the ground)

Flat Towing (all four

wheels on the ground)

Model

TOWING A DISABLED VEHICLE

FWD Without a Key NOT Permitted Recommended Method May Be Used NOT Permitted

NOT Permitted Recommended Method May Be Used NOT Permitted

FWD Automatic

Transaxle With a Key

Recommended Method May Be Used NOT Permitted

May be Used with the

FWD Manual Transaxle

transmission in

With a Key

*NEUTRAL

NOT Permitted Recommended Method NOT Permitted NOT Permitted

AWD Without a Key NOT Permitted Recommended Method NOT Permitted NOT Permitted

AWD Automatic

Transaxle With a Key

Recommended Method NOT Permitted NOT Permitted

May be Used with the

AWD Manual Transaxle

transmission in

With a Key

51

*NEUTRAL

*To shift to NEUTRAL, there is a removable plug in the right side of the shift lever housing that allows you to insert your finger to

override the system. The ignition key must be in the ON position to use the override lever.

WHAT TO DO IN EMERGENCIES

FREEING A STUCK VEHICLE

• If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking
motion. Turn your steering wheel right and left to clear the area around the front wheels.
Then move the shift lever back and forth between REVERSE and DRIVE. Using minimal
accelerator pedal pressure to maintain the rocking motion, without spinning the wheels,
is most effective.

NOTE: To improve the vehicle's traction when starting off in deep snow, sand or gravel, it
may be desirable to switch the Electronic Stability Control (ESC) to “Partial Off” mode by
momentarily pressing the ESC Off
Owner's Manual on the DVD.

Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds
may cause tire damage or failure. A tire could explode and injure someone. Do not
spin your vehicle’s wheels faster than 30 mph (48 km/h) when you are stuck. Do not
let anyone near a spinning wheel, no matter what the speed.

• When “rocking” a stuck vehicle by moving between 1st and REVERSE, do not spin
the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.

• Revving the engine or spinning the wheels too fast may lead to transmission
overheating and failure. It can also damage the tires. Do not spin the wheels
above 30 mph (48 km/h) while in gear (no transmission shifting occurring).

switch. For further information on ESC, refer to the

WARNING!

CAUTION!

52

WHAT TO DO IN EMERGENCIES

EVENT DATA RECORDER (EDR)

• This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR
is to record, in certain crash or near crash-like situations, such as an air bag deployment
or hitting a road obstacle, data that will assist in understanding how a vehicle's systems
performed. The EDR is designed to record data related to vehicle dynamics and safety
systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is
designed to record such data as:

• How various systems in your vehicle were operating;

• Whether or not the driver and passenger safety belts were buckled/fastened;

• How far (if at all) the driver was depressing the accelerator and/or brake pedal; and,

• How fast the vehicle was traveling.

• This data can help provide a better understanding of the circumstances in which a crash
and injuries occur. NOTE: EDR data is recorded by your vehicle only if a non-trivial crash
situation occurs; no data is recorded by the EDR under normal driving conditions and no
personal data (e.g., name, gender, age, and crash location) is recorded. However, other
parties, such as law enforcement, could combine the EDR data with the type of
personally identifying data routinely acquired during a crash investigation.

• To read data recorded by an EDR, special equipment is required, and access to the
vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such
as law enforcement, that have the special equipment, can read the information if they
have access to the vehicle or the EDR.

53

MAINTAINING YOUR VEHICLE

OPENING THE HOOD

• Pull the release lever located below the instrument panel and in front of the driver’s door.

• Raise the hood and locate the safety latch, in the middle of the hood opening.

• Move the safety latch while lifting the hood at the same time.

• Insert the support rod into the slot on the hood.

• To close the hood, remove the support rod and place it in the retaining clip, then lower
the hood slowly.

WARNING!

Be sure the hood is fully latched before driving your vehicle. If the hood is not fully
latched, it could open when the vehicle is in motion and block your vision. Failure to
follow this warning could result in serious injury or death.

54

MAINTAINING YOUR VEHICLE

ENGINE COMPARTMENT

2.0L Engine

55

MAINTAINING YOUR VEHICLE

2.4L Engine

56

MAINTAINING YOUR VEHICLE

FLUIDS AND CAPACITIES

Component

Engine Coolant 2.0L, 2.4L MOPAR® Antifreeze/

Engine Oil with Filter 2.0L,

2.4L

Fuel Selection 2.0L, 2.4L 87 Octane 13.6 Gallons (51.5 Liters)
Engine Oil Filter 2.0L, 2.4L MOPAR® Engine Oil Filter

Spark Plugs 2.0L, 2.4L ZFR5F-11 (Gap 0.043 in

Automatic Transaxle (CVT) MOPAR® CVTF + 4®

Manual Transaxle MOPAR® ATF+4®

Rear Drive Assembly (RDA) MOPAR® Gear & Axle

Power Transfer Unit (PTU) MOPAR® Gear & Axle

Brake Master Cylinder MOPAR® DOT 3 and SAE

Power Steering Reservoir MOPAR® Power Steering

Fluid, Lubricant, or
Genuine Part

Coolant Five
Year/100,000 Mile Formula
HOAT (Hybrid Organic
Additive Technology) or
equivalent.

API Certified SAE 5W-20
engine oil, meeting the
requirements of Chrysler
Material Standard
MS-6395. Refer to the
engine oil filler cap for
correct SAE grade.

or equivalent.

[1.11 mm])

Automatic Transaxle Fluid.

Automatic Transmission
Fluid or equivalent
licensed ATF+4® product.

Lubricant SAE 80W-90 API
GL 5 or equivalent
non-synthetic product.

Lubricant SAE 80W-90 API
GL 5 or equivalent
non-synthetic product.

J1703 should be used or
equivalent. If DOT 3 is not
available, then DOT 4 is
acceptable. Use only
recommended brake fluids
or equivalent.

Fluid +4 or MOPAR®
ATF+4® Automatic
Transmission Fluid or
equivalent licensed
ATF+4® product.

Capacities

7.2 Quarts (6.8 Liters)
Includes heater and
coolant recovery bottle
filled to MAX level.

4.5 Quarts (4.26 Liters)

—

—

—

—

—

—

—

—

57

MAINTAINING YOUR VEHICLE

X

XX

6,000 12,000 18,000 24,000 30,000 36,000 42,000 48,000 54,000 60,000 66,000 72,000 78,000

Miles:

Or Months: 6 12 18 24 30 36 42 48 54 60 66 72 78

MAINTENANCE CHART

10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000

Or Kilometers:

Change the engine oil and filter. XXXXXXXXXXXXX

XXXX X

Rotatethetires. XXXXXXXXXXXXX

If using your vehicle for any of the following: dusty or

off-road conditions. Inspect the engine air cleaner

XXXX

Inspect the brake linings; replace if necessary. XXXXXX

Replace the air conditioning filter. XXXXXX

Inspect the CV joints. Perform the first inspection at

12,000 miles (20,000 km) or 12 months.

filter; replace if necessary.

Inspect the exhaust system. Perform the first

XXXXXX

XXXX

Inspect the front suspension, tie rod ends and boot

seals for cracks or leaks and all parts for damage,

wear, improper looseness or end play; replace if

necessary.

Replace the engine air cleaner filter. X X

Adjust the parking brake on vehicles equipped with

four-wheel disc brakes.

Change the manual transmission fluid if using your

vehicle for any of the following: trailer towing, snow

plowing, heavy loading, taxi, police, delivery service

(commercial service), off road, desert operation or

more than 50% of your driving is at sustained speeds

during hot weather, above 90°F (32°C).XChange the automatic transmission fluid & filter if

using your vehicle for any of the following: police,

inspection at 12,000 miles (20,000 km) or 12 months.

taxi, fleet, or frequent trailer towing.

• Refer to the Owner's Manual on the DVD for the complete maintenance schedule.

58

MAINTAINING YOUR VEHICLE

Maintenance Record

Odometer Date Signature, Authorized Service Center

6,000 Miles
(10,000 km) or
6 Months

12,000 Miles
(20,000 km) or
12 Months

18,000 Miles
(30,000 km) or
18 Months

24,000 Miles
(40,000 km) or
24 Months

30,000 Miles
(50,000 km) or
30 Months

36,000 Miles
(60,000 km) or
36 Months

42,000 Miles
(70,000 km) or
42 Months

48,000 Miles
(80,000 km) or
48 Months

54,000 Miles
(90,000 km) or
54 Months

60,000 Miles
(100,000 km)
or 60 Months

66,000 Miles
(110,000 km)
or 66 Months

72,000 Miles
(120,000 km)
or 72 Months

78,000 Miles
(130,000 km)
or 78 Months

59

MAINTAINING YOUR VEHICLE

FUSES

Integrated Power Module (IPM)

• The Integrated Power Module (IPM) is located in the engine compartment near the air
cleaner assembly. This center contains cartridge fuses and mini-fuses.

Cavity Cartridge Fuse Mini-Fuse Description

1 Empty Empty
2 15 Amp Lt Blue AWD/4WD ECU Feed
3 10 Amp Red CHMSL Brake Switch Feed
4 10 Amp Red Ignition Switch Feed/OCM
5 20 Amp Yellow Trailer Tow
6 10 Amp Red IOD Sw/Pwr Mir/Steering Cntrl

7 30 Amp Green IOD Sense1
8 30 Amp Green IOD Sense2

9 40 Amp Green Power Seats
10 20 Amp Yellow CCN Power Locks/Interior Lighting
11 15 Amp Lt Blue Power Outlet
12 20 Amp Yellow Ign Run/Acc Inverter
13 20 Amp Yellow Pwr Run/Acc Outlet RR/Dome

14 10 Amp Red IOD CCN
15 40 Amp Green RAD Fan Relay Battery Feed
16 15 Amp Lt Blue IGN Run/ACC Dome Lamp/Sunroof/

17 10 Amp Red IOD Feed Mod-Wcm
18 40 Amp Green ASD Relay Contact PWR Feed
19 20 Amp Yellow PWR Amp 1 & Amp 2 Feed
20 15 Amp Lt Blue IOD Feed Radio

Sdar/Hands-Free Phone

Lamp/Cigar Lighter

Rear Wiper Motor/ACC Inverter

60

MAINTAINING YOUR VEHICLE

Cavity Cartridge Fuse Mini-Fuse Description

21 10 Amp Red IOD Feed Intrus Mod/Siren (If

22 10 Amp Red IGN RUN Heat/AC/Compass Sensor
23 15 Amp Lt Blue ENG ASD Relay Feed 3
24 15 Amp Lt Blue Power Sunroof Feed
25 10 Amp Red Heated Mirror (If Equipped)
26 15 Amp Lt Blue ENG ASD Relay Feed 2
27 10 Amp Red IGN RUN Only ORC Feed
28 10 Amp Red IGN RUN ORC/OCM Feed
29 Hot Car (No Fuse Required)
30 20 Amp Yellow Heated Seat (If Equipped)
31 10 Amp Red Headlamp Washer Relay Control (If

32 30 Amp Pink ENG ASD Control Feed 1
33 10 Amp Red ABS MOD/J1962 Conn/PCM
34 30 Amp Pink ABS Valve Feed
35 40 Amp Green ABS Pump Feed
36 30 Amp Pink Headlamp/Washer Control/Smart

37 25 Amp Natural Diesel Fuel Heater (If Equipped)

TIRE PRESSURES

• Check the inflation pressure of each tire, including the spare tire, at least monthly and
inflate to the recommended pressure for your vehicle.

• The tire pressures recommended for your vehicle are found on the “Tire and Loading
Information” label located on the driver’s side door opening.

NOTE: Refer to the Owner's Manual on the DVD for more information on the life of tires.

Equipped)

Equipped)

Glass (If Equipped)

WARNING!

Overloading of your tires is dangerous. Overloading can cause tire failure, affect
vehicle handling, and increase your stopping distance. Use tires of the
recommended load capacity for your vehicle. Never overload them.

61

MAINTAINING YOUR VEHICLE

WARNING!

Improperly inflated tires are dangerous and can cause accidents. Under-inflation is
the leading cause of tire failure and may result in severe cracking, component
separation, or “blow out”. Over-inflation reduces a tire’s ability to cushion shock.
Objects on the road and chuck holes can cause damage that results in tire failure.
Unequal tire pressures can cause steering problems. You could lose control of your
vehicle. Over-inflated or under-inflated tires can affect vehicle handling and can fail
suddenly, resulting in loss of vehicle control.

WHEEL AND WHEEL TRIM CARE

• All wheels and wheel trim, especially aluminum and chrome plated wheels, should be
cleaned regularly with a mild soap and water to prevent corrosion.

• To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or
equivalent or select a non-abrasive, non-acidic cleaner.

CAUTION!

Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use
oven cleaner. These products may damage the wheels protective finish. Avoid
automatic car washes that use acidic solutions or harsh brushes that may damage
the wheels protective finish. Only MOPAR® Wheel Cleaner or equivalent is
recommended.

EXTERIOR BULBS

LIGHT BULBS – Exterior Bulb Number

Backup Lamp W16W (921)
Center High-Mounted Stop Lamp

(CHMSL)
Fog Lamp PSX24W
Front Park/Turn Signal/Side Marker

Lamp
Rear Tail/Stop Lamp 3157
Rear Turn Lamp 3157AK or 3157A
Low Beam/High Beam Headlamp H13
License Lamp W5W
Off–Road Lamp H3

* CHMSL is not serviceable. It is a LED lamp. To replace the LED, the entire CHMSL
assembly must be replaced.

LED (*)

3757AK

62

CONSUMER ASSISTANCE

CHRYSLER GROUP LLC CUSTOMER CENTER

P.O. Box 21–8004

Auburn Hills, MI 48321–8004

Phone: [phone]

CHRYSLER CANADA INC. CUSTOMER CENTER

P.O. Box 1621

Windsor, Ontario N9A 4H6

Phone: [phone]

ASSISTANCE FOR THE HEARING IMPAIRED

• To assist customers who have hearing
difficulties, the manufacturer has
installed special TDD
(Telecommunication Devices for the
Deaf) equipment at its customer center.
Any hearing or speech impaired
customer, who has access to a TDD or
a conventional teletypewriter (TTY) in
the United States, can communicate
with the manufacturer by dialing
1–800–380–CHRY. Canadian residents
with hearing difficulties that require
assistance can use the special needs
relay service offered by Bell Canada.
For TTY teletypewriter users, dial 711
and for Voice callers, dial
1–800–855–0511 to connect with a Bell
Relay Service operator.

WARNING!

Engine exhaust, some of its
constituents, and certain vehicle
components contain, or emit,
chemicals known to the State of
California to cause cancer and birth
defects, or other reproductive harm.
In addition, certain fluids contained
in vehicles and certain products of
component wear contain, or emit,
chemicals known to the State of
California to cause cancer and birth
defects, or other reproductive harm.

PUBLICATIONS ORDERING

• If you are the first registered retail
owner of your vehicle, you may obtain a
free printed copy of the Owner's
Manual, Warranty Booklet or Radio
Manuals on your DVD by calling
1–800–992–1997 (U.S.) or
1–800–387–1143 (Canada) or by
contacting your dealer.

• Replacement User Guides or DVDs or,
if you prefer, a printed copy of the
Owner's Manual, Warranty Booklet or
Radio Manuals may be purchased by
visiting www.techauthority.com or by
calling 1–800–890–4038 (U.S.) or
1–800–387–1143 (Canada). Visa, Master
Card, American Express and Discover
orders are accepted. If you prefer
mailing your order, please call the
above numbers for an order form.

63

CONSUMER ASSISTANCE

NOTE: A street address is required
when ordering manuals (no P.O. Boxes).

NOTE:

• The Owner's Manual and User Guide
electronic files are also available on the
Chrysler, Jeep and Dodge websites.

• Click on the "For Owners" tab, select
"Owner/Service Manuals", then select
your desired model year and vehicle
from the drop down lists.

REPORTING SAFETY DEFECTS IN THE 50 UNITED STATES AND WASHINGTON, D.C.

• If you believe that your vehicle has a
defect that could cause a crash or
cause injury or death, you should
immediately inform the National
Highway Traffic Safety Administration
(NHTSA) in addition to notifying the
manufacturer.

• If NHTSA receives similar complaints,
it may open an investigation, and if it
finds that a safety defect exists in a
group of vehicles, it may order a recall
and remedy campaign. However,
NHTSA cannot become involved in
individual problems between you, your
authorized dealer, and the
manufacturer.

• To contact NHTSA, you may either call
the Auto Safety Hotline toll free at
1–888–327–4236 (TTY: 1–800–424–

9153), or go to http://www.safercar.gov;
or write to: Administrator, NHTSA, 1200
New Jersey Avenue, SE., West
Building, Washington, D.C. 20590. You
can also obtain other information about
motor vehicle safety from
http://www.safercar.gov.

In Canada

• If you believe that your vehicle has a
safety defect, you should contact the
Customer Service Department
immediately. Canadian customers who
wish to report a safety defect to the
Canadian government should write to:
Transport Canada, Motor Vehicle Defect
Investigations and Recalls, 2780
Sheffield Road, Ottawa, Ontario K1B
3V9.

TIRE WARRANTY

Tire Limited Warranty And Adjustment Policy

• When a tire is removed from service
due to a covered warranty condition
under a tire manufacturer’s “Limited
Warranty Program”, you may be
eligible for a free tire replacement or a
comparable new tire on a “prorated
basis”.

• Certain conditions, such as irregular
wear or tire damage due to road
hazards, collision, improper inflation,
intentional alteration, and misuse, are
excluded from the Limited Warranty
Program. The Limited Warranty
Program expires when your tires either
wear to a specified tread depth, and/or
after a period of time from the date of
purchase, as stated in the Tire
Warranty on the DVD.

NOTE: Refer to the Tire Warranty on
the DVD for specific information
relating to the manufacturer's limited
warranty for the tires installed on
your vehicle. If you have any
questions regarding the limited tire
warranty coverage, contact your
local authorized dealer or your local
authorized tire dealer.

64

CONSUMER ASSISTANCE

Disclaimer:

• THE TIRE MANUFACTURER’S LIMITED
WARRANTY PROGRAM, THE DETAILS
OF WHICH CAN BE FOUND, ON THE
OWNERS MANUAL DVD, THE TIRE
MANUFACTURER’S WEBSITE OR AT
ANY AUTHORIZED SERVICE CENTER
ARE IN LIEU OF ALL OTHER REMEDIES
OR WARRANTIES, EXPRESS OR
IMPLIED, ARISING BY LAW OR
OTHERWISE, INCLUDING FITNESS FOR
A PARTICULAR PURPOSE OR
MERCHANTABILITY. THE TIRE
MANUFACTURER EXPRESSLY
DISCLAIMS LIABILITY FOR INDIRECT,
SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOST
PROFIT, LOSS OF BUSINESS, LOSS OF
GOODWILL, LOSS OF REPUTATION,
PUNITIVE OR ANY OTHER DAMAGE,
COST OR LOSS OF ANY KIND. SOME
STATES AND PROVINCES DO NOT
ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.

WARNING!

NOTE: Refer to the Owner’s Manual
on the DVD for complete warning
information that could prevent
accidents, injuries and even deaths.

WARNING!

Death, serious injury and/or property
damage may result from:

• Tire failure due to impact damage
and/or improper maintenance.

(Continued)

WARNING! (Continued)

• Tires should be inspected
regularly by a qualified technician
for signs of damage, such as
punctures, impacts,
under-inflation or overloading.

• Progressive air loss may result
from punctures, cuts, curbing,
impacts or partial bead unseating.

Some fitment causes for air loss are:

• Incomplete bead seating.

• Bead tearing caused by a machine
tool due to insufficient lubrication
or improper adjustment.

• Leaking valve core or rubber valve
components (these should be
replaced when problems are
detected and whenever tires are
replaced).

• Tire failure due to improper
repairs.

• See Rubber Manufacturer’s
Association (RMA) established
repair procedures at www.rma.org
for information on proper repair
procedures. Never perform a
temporary repair or use an inner
tube as a substitute for a proper
repair. Only qualified persons
should repair tires.

• Explosion of tire/rim assembly due
to improper mounting.

• Only specially trained persons
should mount tires.

• Failure to mount tires on approved
rims.

• Failure to deflate single or dual
assemblies completely before
demounting.

65

CONSUMER ASSISTANCE

Using Lift Kits

• Use of lift kits with some vehicle/tire
combinations can cause instability or
loss of control. When changing tire
sizes, always consult an installer for
optimum rim width and carefully check
vehicle/tire clearances.

Check Your Tires For Damage

• Frequent (at least monthly) inspection
of your tires for signs of damage,
uneven tread wear and their general
condition is important for safety.
Impacts, penetrations, cracks, knots,
bulges or air loss always require tire
removal and expert inspection.

Tire Service Life

• The service life of a tire is dependent
upon varying factors including, but not
limited to, your driving style, tire
pressure and distance driven.

WARNING!

Tires and the spare tire should be
replaced after six years, regardless
of the remaining tread. Failure to
follow this warning can result in
sudden tire failure. You could lose
control and have an accident
resulting in serious injury or death.

• Keep dismounted tires in a cool, dry
place with as little exposure to the light
as possible.

• Protect tires from contact with oil,
grease, and gasoline.

NOTE: All tire warranties are made by
the tire manufacturer. Tires are not
covered under your Chrysler New Vehicle
Limited Warranty.

66

MOPAR ACCESSORIES

MOPAR® ACCESSORIES

• The following highlights just some of the authentic Jeep Accessories by MOPAR® that
have been engineered to customize your Jeep Patriot.

• To see the full line of accessories, stop by your Jeep dealer or visit MOPAR.com.

EXTERIOR:

• Driving Lights • Sunroof Air Deflector • Front Air Deflector

• Hitch Receiver • Front End and Hood

• Fog Lights • Side Window Air

INTERIOR:

• Premium Carpet Floor
Mats

• Slush Mats • Ambient Light Kit • Heated Seats

ELECTRONICS:

• Portable Navigation
Systems

• iPod® Adapter • Media Center 430 (RBZ

• Kicker® Sound System • Media Center 730 (RER

Cover

Deflectors

• Door Sill Guards • Bright Pedal Kit

• Uconnect™ Web (WiFi) • Uconnect™ Phone

Multimedia Radio)

Navigation Radio)

• Molded Splash Guards

• Off Road Lights

• DVD Rear Seat Video™

• Remote Start

CARRIERS:

• Hitch-mount Bike
Carrier

• Roof Mount Ski and
Snowboard Carrier

• iPod® is a registered trademark of Apple, Inc.

• Kicker® is a registered trademark of Stillwater Designs and Audio, Inc.

• Roof Mount Bike Carrier • Roof Box Cargo Carrier

• Roof Mount Water Sports
Carrier

67

• Roof Mount Canoe
Carrier

NOTES

68

This guide has been prepared to help you get

quickly acquainted with your new Jeep and to

provide a convenient reference source for

common questions. However, it is not a

substitute for your Owner’s Manual.

For complete operational instructions,

maintenance procedures and important safety

messages, please consult your Owner’s

Manual, Navigation Radio User Manual,

Multimedia User Manual and other Warning

Labels in your vehicle.

Not all features shown in this guide may apply

to your vehicle. For additional information on

accessories to help personalize your vehicle,

visit www.mopar.com or your local Jeep dealer.

JEEP.com

10MK74-926-AA

Patriot

Second Printing

User Guide