XU253 JDW 2.8 LITRE CYLINDER
User Manual
Plug Wiring (UK)
This appliance is fitted with a BS1363 13 amp plug. If you have to replace the fuse, only those
that are BSI-approved to BS1362 and with a rated current of 13 amps should be used. Spare
fuses are available from electrical stores. If the plug outlets in your home are not suitable for the
plug of this product, the plug must be removed and disposed of safely as insertion of the plug
into a socket is likely to cause electric hazard.
A replacement plug should be wired according to the following instructions.
If in doubt, contact a qualified electrician.
This appliance must be earthed. The wires in the cord set are coloured in the following way:
BLUE-NEUTRAL. BROWN-LIVE, GREEN&YELLOW-EARTH
The wire that is coloured blue must be connected to the terminal that is marked with the
letter N.
The wire that is coloured brown must be connected to the terminal that is marked with the
letter L.
The wire that is coloured green & yellow must be connected to the terminal in the plug that is
marked with the letter E or marked with symbol.
If the supply cord is damaged, a qualified person must replace it in order to avoid a hazard.
Environment
The "crossed-out wheeled bin" symbol indicates that this product can be
recycled. Do not dispose of with household waste. Please take the product to
your local refuse/collection site centre. If you are unsure of where you local
refuse centre is, please contact your local authority.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER
WARNING： When using an electrical appliance, basic precautions should
already be followed, including the following:
1. For the first operation, it is advisable to read the manual carefully beforehand and
keep it properly for future use.
2. Before the first operation, make sure the dust cup or the dust bag is properly
installed.
3. Make sure the power supply is 220-240V~ 50/60Hz
4. Do not vacuum water and inflammable material.
5. Do not vacuum burning material and ashes.
6. Do not use the machine without a motor protection filter filled.
7. Please change the dust bag immediately when it was damaged.
8. Do not store or use the machine close to high temperature places.
9. Dot not let children use the machine in case of danger.
10. If abnormal noise, smell, smoke or any other failure or breakage is found during
the operation, you should turn off the switch and unplug it. Then, contact with
your service centre for repair. Do not repair by yourself.
11. If the power cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
12. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
13. Children should be supervised to ensure that they do not play with the appliance.
14. The plug must be removed from the power socket before any maintenance or
replacement.
15. This appliance may be used by children aged 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning safe use
of the appliance and understand the hazards involved. Children should not play
with the appliance. Children should not carry out cleaning and user maintenance
without supervision.
! WARNING!
The plug must be removed from the power socket before any maintenance or
replacement.
If the power cord is damaged, replace it only by the factory or maintenance
centre or similarly qualified persons.
1 Dust cup
2 Dust cup buckle
3 Machine lifting handle
4 Cord rewind button
5 ON/OFF& power level button
6 Wheel
7 Hose joint
8 Hose
9 Curved handle of hose
10 Metal extension tube
3 interchangeable heads
11 Floor cleaning head
12 Spinning head (free tool)
13 Brush head (free tool)
Extension device
1 2 3 4 5 6 7 8 9
10
11
12
13
HOW TO USE
Assemble hose and metal extension tube
1 2 3 4
1. Attach the hose to the vacuum cleaner.
Align the hose joint to the inlet of the vacuum cleaner and insert it into the inlet.
To detach the hose, press the buckles on the sides of the joint and pull out the hose.
2. Attach the curved handle of hose to metal extension tube
3. Push the extension device forward first.
4. While continuously pushing the extension device forward, push out or pull back the
extension metal tube to the desired length.
Choose 1 of the 3 heads and assemble
Cord rewind button
5 6 7
8 9 10
5. Attach the floor cleaning head to the metal extension tube.
6. Press the brush button. The front brushes of the head are pushed out.
The floor cleaning head is suitable for vacuum-cleaning hard floors or short carpets.
7. The enlarged picture shows the front brushes.
8. Attach the spinning head to the metal extension tube. The spinning head spins to deeply
reach the inside of thick carpets.
9. Attach the brush head to the metal extension tube.
10. Rotate the brush head by following the direction of the arrow on it. The brush head cleans
small seams in window, furniture, corners and ceiling, etc., and dust on short hair fabric furniture
and inaccessible places.
Use the machine
Min Max
ON/OFF & power level button
11 12 14
11. Pull the power cord out. Do not pull beyond the red marking.
12. Remove the plastic cover and the paper on the prongs.
13. Plug the machine to a power supply socket.
14. Press (using hand or foot) the ON/OFF & power level button once to turn on the machine.
Suction power level control: Rotate clockwise to min./anticlockwise to max.
15. To turn off, press (using hand or foot) the ON/OFF& power level button again.
14. After use, unplug the machine, and then press the cord rewind button to rewind the power
cord back into the machine.
Steps to clean the dust cup
JD Williams and Co Ltd
M60 6ES
Retain this information for future reference.
15 16 17 18
19 20 21
1. Take out the dust cup. (Fig. 15)
2. Gently push the dust dump button to dump dust. (Fig. 16, 17)
3. In case the suction power is insufficient when the waste has not reached MAX, turn
off the machine; repeat the above steps 1-2; detach dust cup cover and take out the
filter sponge for cleaning. (Fig. 17, 18)
4. In case of cleaning the inside of the dust cup, please operate according to the
following steps:
1) Rotate the dust cup cover to detach it and take out the filter sponge (Fig. 18)
2) Take out secondary filter system. (Fig. 19)
3) Remove dust press panel and filter net. (Fig. 20)
4) Wash the separator under the water tap, and then thoroughly dry it out. (See NOTE)
5) Reassemble the dust cup and install it. (Fig. 21)
NOTE: After cleaning the filter components, dry them first before putting back into the
machine for use. It is suggested to expose to sunshine for 24 hours until they are
completely dry. Make sure each component is back in place otherwise it may cause
malfunction. Do not allow water to get into the electrical components otherwise it may
cause malfunction.
Loading...