JCM RContactR User Manual

RCONTACT R

User’s Manual

Introduction

The system is designed for applications where pedestrian doors installed on garage doors. Is a position detection system of
the pedestrian door status, so that if it is open the system prevents the start of the movement of the garage door.
Is a wireless system composed by one transmitter and one receiver. The receiver monitors the status of transmitters connected to it.

The system complies with EN ISO 13849-1, category 2, PLc.

Technical data

Frequency 869,50 MHz
Power supply 12/24V ac/dc (9-35V dc / 8-28V ac)
Consumption standby/operating 18mA/80mA
Memory 6 transmitters (3 on relay 1, 3 on relay 2)
Relay numbers 2 relays
Relay contacts 1A
Radiated power < 1mW
Operating temperature -20ºC - +85ºC
Seal IP54 (with IP65 cable glands)
Box size 82 x 190 x 40mm
Range 50m

Starting up

Mechanical installation

Fix the back of the box to the wall, using the wall plugs and screws supplied. Install the receiver, close to the door and avoid metal
surfaces between the receiver and the transmitter. Pass the cables through the bottom of the receiver. Connect the power cables to
the terminals of the printed circuit, following the indications of the connections diagram. Store the transmitter on the receiver. Fix
the front of the receiver to the back with the screws supplied for the purpose.

Programming the transmitter on the receiver

While programming the receiver, press the PROG button on the transmitter to be programmed into the receiver.
The receiver allows programming 6 transmitters (3 for Relay 1 and 3 for Relay 2).
Each safety edge transmitter must be learnt into the appropriate channel of the safety edge receiver.

1248086_Rev1.0RCONTACTR Page1/3

Mode Configuration of transmitter programming in the receiver.

1 When you open the pedestrian door, relay 1 on the receiver will be activated

Led R1 Led R2

ON OFF
2 When you open the pedestrian door, relay 2 on the receiver will be activated OFF ON
3 When you open the pedestrian door, the two relays will be activated at the same time ON ON

PRESS RPORG BUTTON LED TURNS ON PRESS TRANSMITTER PROG ONE BEEP & PROGRAMMED

PRESS RPROG BUTTON LED TURNS OFF & END PROG

Autotest signal

Check the autotest output on the control panel, in stanby, to see whether the voltage is 0V (positive polarization) or 12/24V ac/dc
(inverted test input). Switch on the autotest signal of the panel and check that it has a maximum duration of 3 seconds.

Autotest output

Connection to a equipment with
autotest

Connection to a equipment without
autotest **

* Nota: Connect autotest only for used outputs.
** Where the autotest is not used, the system is not checked at the start of the operation, which means that security standard EN 12453 regarding the use of motorised
garage doors is, in some cases, not complied with..

in standby

0V 12/24V

12/24V 0V Inverted ON Connected* Connected*

--- --- --- OFF Not connected Not connected

Autotest output
activated

Polarization type

Positive

Jumper
ATEST POL

OFF

ATEST1 ATEST2

Connected* Connected*

Maintenance

Beeps and leds messages / errors indication table

B1/B2
Led

ON OFF No beeps RCONTACT R Detection of pedestrian door at open state

OFF OFF 4 beeps each

OFF ON No beeps RCONTACT R Check function. See coverage and signal quality

System Check

This function has to be used to check the operation and range of all the devices once the installation has been carried out.
Press the receiver’s CHECK button for at least 1 second to enter check mode. The indicator light will come on and four beeps will be
heard.
Perform a complete door opening and closing manoeuvre. During the system check a beep will be heard every 1,5 seconds.

1248086_Rev1.0RCONTACTR Page2/3

Check
Led

Beeps Equipment Message / error Solution

RCONTACT transmitter not programmed Verify if it must be programmed and perform the

Communication failure between RCONTACT R
and RCONTACT T

RCONTACT R RCONTACT/T low battery Verify the batteries of the transmitter

20 seconds

table.

---

programming.
Verify the batteries of the emitter and if they are
charged, verify the radio signal with the Check
function.

---