JCM RBMOT30, RBMOT500 User Manual

COD. 1248054-GB / 1.1

Frequency

MOTION: 868,35MHz RADIOBAND1G: 868,90MHz

Coding

High security rolling code

Memory

RBMOT30: 30 codes / RBMOT500: 500 codes RADIOBAND1G: Ex. 6 RADIOBAND/TBX (3 on relay 1, 3 on relay 2)

Supply

12/24V ac/dc

Power supply range

9-24 / 21-35V dc 8-16 / 15-28V ac

Number of relays

MOTION: 2 relays (R1 and R2) RADIOBAND1G: 2 relays (B1 and B2)

Relay contacts

Standby/Op. consumption

RBMOT30: 18mA / 115mA / RBMOT500: 22mA/244mA

Self-test input

2 0/12/24V AC/DC inputs with selectable polarity

Radiated power

< 25mW

Op. temperature

-20ºC to +70ºC

Watertightness

IP54 (with glands IP65)

Size

63x55x15mm

Box dimensions

140x220x55mm

Range (guaranteed)

MOTION: 100m RADIOBAND1G: 10m

RBMOT30 / RBMOT500

GENERAL DESCRIPTION

This equipment consists of 30 or 500 codes MOTION receiver and receiver to RADIOBAND 1G system.

TECHNICAL CHARACTERISTICS

COD. 1248054-GB / 1.1

TWO SAFETY EDGES CONNECTION WITH NEGATIVE POLARIZATION AUTOTEST

CONTROL PANEL

RBMOTION

Led

OFF

Flashing

Relay R1 Activation

R1 desactivated, state by default

Every 5 seconds, correct supply of the equipment

R2/LB

Relay R2 Activation/ Indicates if the transmitter has low battery

R2 desactivated, state by default/

Indicates if the transmitter„s battery is

working properly

Every 5 seconds, correct supply of the equipment

Relay B1 Activation or band not connected

B1 desactivated, correct safety edge state

Relay B2 Activation or band not connected

B2 desactivated, correct safety edge state

CHECK

Coverage (See CHECK funcftion)

RBMOT30 / RBMOT500

INSTALLATION AND CONNECTIONS

Attach the rear part of the housing to the wall using the plugs and screws supplied. Pass the cables through the bottom of the receiver. Connect the power cables to the terminals marked in the mother board, as indicated. Install the receiver, close to the door and avoid metal surfaces between the receiver and the transmitter RADIOBAND. Pass the cables through the bottom of the receiver. Program transmitters and transmitters RADIOBAND as programming section. Fix the front of the receiver to the back with the screws supplied for the purpose.

1- Power supply 12/24V AC/DC: (+) 2- Power supply 12/24V AC/DC: (-)

3,4- R1: Connection to the safety band input of the control panel (resistive contact 8.2k) with jumper in position BS1. Or to the control panel safety contact input (NC) with jumper in position CS1. 5,6- R2: Connection to a second safety band input of the control panel (resistive contact 8.2k) with jumper in position BS2. Or to the control panel safety contact input (NC) with jumper in position CS2. 7- AUTOTEST: Common connection safety self-test (-). See Figure and table POLARIZED SELF-TEST. 8- AUTOTEST: Self-test connection for R1. See Figure and table POLARIZED AUTO-TEST. 9- AUTOTEST: Self-test connection for R2. See Figure and table POLARIZED AUTO-TEST. 10, 11- R1: Relay 1 output RADIO receiver 12, 13- R2: Relay 2 output RADIO receiver

LIGHT INDICATORS

COD. 1248054-GB / 1.1

Configuration of transmitter programming in the receiver.

Led R1

Led R2

Standard Programming (default option, the receiver is always configured on pluri-channel)

The relays are activated 1st relay by channel 1 and 2nd relay by channel 2 (3rd relay by channel 1 and 4th relay by channel 2)

Flashing

Special programming

By pressing any transmitter channel, relay 1 on the receiver will be activated

OFF

By pressing any transmitter channel, relay 2 on the receiver will be activated

OFF

By pressing any transmitter channel, the two relays will be activated at the same time*

ON In programation

Relay B1 Led

Turned on. It indicates the channel to program.

Relay B2 Led

Turned on. It indicates the channel to program.

RBMOT30 / RBMOT500

OPERATING

The pilot lights are activated every 5 seconds to indicate the correct supply of power to the equipment.

Upon receiving a code, the receiver checks whether it is in its memory, activating the corresponding relay R1 and/or R2. The relay activation mode is selected in either impulse or ON/OFF using the Imp/Bies jumper (only with the relay 2). For adjustment of relay 1, see manual of the programming tool.

The receiver checks that all the programmed bands are working properly. If a band is activated or if there is an error in its operation, the receiver activates the appropiated B1 or B2 output relay and the appropiated B1 or B2 light indicator turns on.

PROGRAMMING

MANUAL PROGRAMMING OF MOTION TRANSMITTERS

Press the receiver programming button for 1 sec. and an acoustic signal will be heard. The receiver will enter standard programming (see table). If the receiver programming button is held pressed down, the receiver Hill enter special programming, cyclically passing from one configuration to the next. Once the programming configuration for the transmitter to be registered has been chosen, send the code to be programmed by pressing the transmitter. Every time a transmitter is programmed, the receiver will issue an acoustic signal for 0.5 sec.

*If working in ON/OFF activation mode, relay 1 will act as impulse and relay 2 as ON/OFF. Therefore, on the first press relay 1 will close and open the contact and relay 2 will only close. On the second, relay 1 will close and open the contact and relay 2 will open.

N.B.: Each transmitter can be configured independently on the receiver.

MANUAL PROGRAMMING OF RADIOBAND TRANSMITTERS

Makes it possible to store 6 RADIOBAND transmitters (3 Relay B1 and 3 on Relay B2). Press the receiver programming PROG button for 1s; a sound signal will be heard. The receiver will enter safety band closing programming mode (BSC). If the programming button is kept pressed, the receiver will enter safety band opening programming mode (BSO),

moving cyclically from one really to another. Once the programming relay has been chosen for the transmitter you want to start using, send the programming code by pressing the RADIOBAND transmitter. Every time a transmitter is programmed, the receiver will emit a sound signal for 0.5s.

+ 4 hidden pages