JCM Manager+DCS Installation Manual
Version 3.0X D
MANAGER Portable Programmer+DCS
Personalised programming for distributors
General considerations
¾ Ingeniería de Control supplies MANAGER+DCS portable programmers with their
distributor code.
¾ Each distributor can assign 64 secret installer codes. The assignable codes are
from no. 00 to no. 30 and from no. 32 to no. 64.
¾ The units have the factory default installer code of no. 31 (open code) which
means that they are not personalised.
¾ Memory cards , both for receivers and for access control centres, are never
supplied personalised. They are configured when the first recording is made.
¾ It is important not to sell installer version MANAGER+DCS portable
programmers (3.0X D), because these have the feature making it possible to see
the units’ installer codes.
¾ We recommend that you keep these instructions in a safe place, because they
explain how to personalise a MANAGER+DCS.
Inputting secret installer code
Set the power switch to the ON position. You will hear a long
bleep and you will see the following message on the screen:
Next, the portable Programmer will ask you for the password. This consists of 6 digits; if
you key in fewer digits, the portable Programmer will interpret this as an error, that is to say,
if your password is 9 then you must key in 000009. The factory default password is always
000000.
Each time you press a password number a * symbol will appear
on the screen and you will hear a short bleep.
Once the password has been keyed in correctly you should confirm it by pressing the
key. If you make a mistake you can erase it, before confirmation, by pressing the key.
If you key in an incorrect password you will see the following
message:
Once the password has been correctly keyed in the Main
Menu/Transmitter will appear.
The main menu, as well as the rest of the sub-menus are of the rotating type, which means that
you can move through the various options by pressing the up and down keys
order to make it easier for you to search through the options on each menu, you will find a
sketch of the menus in the Menu Tree section.
Using the
Setup menu. Press
or keys you should select the Main Menu/
.
or . In
.
prog
Version 3.0X D
You will see the following message on the screen
Simultaneously press the and keys. The portable
Programmer will ask you for the password. This consists of 6
digits.
Each time that you press a digit of the password a * symbol will
appear on the screen and you will hear a short bleep.
If you key in an incorrect password the following message will
appear on the screen
If you key in an incorrect password three times the portable Programmer will be
deactivated. To reactivate it leave it on for two minutes and then you will hear an
intermittent bleeping and you will be asked for the password again.
We recommend that you make a careful note of the password number in a
safe place, never on the MANAGER+DCS itself.
Once you have correctly keyed in the password you should confirm it by pressing the
key. If you make a mistake you can erase it, before confirmation, by pressing the
The MANAGER+DCS portable Programmer’s existing installer
code will appear on the screen. If the unit has been programmed
at the factory the installer code no. 31 (open code) will appear, in
other words it is not personalised.
Now key in the code you wish to edit
Remember that the codes which you can assign are from no. 00 to no. 30
and from no. 32 to no. 64.
and press .
You will see the following message on the screen
and finally you will be returned to the menu:
Once you have keyed in the installer code, the following menu is
activated in the MANAGER+DCS portable programmer
This new menu will allow installers to add, at will, the personal code which you have just
assigned them.
To go back to configuring the MANAGER+DCS portable programmer without an installer
code, you should follow the steps set out above and re-input no. 31 as installer code. The
installer code assignment and deletion operation can be carried out as many times as
necessary.
key.
Personalised
Looking at the installer code on-screen
This function can only be carried out using distributor version (3.0X D) MANAGER+DCS
portable programmers.
• Transmitter / Smartcard
Enter the menu corresponding to the element for which you wish
to see the installer code (for example transmitter).
Press
Simultaneously press the and
instructions which appear on the screen. You will then be able to
look at the installer code which the element has recorded in it (in
this case 31)
• Memory cards
Enter the menu corresponding to the element for which you wish
to see the installer code (for example Receiver).
Press
Simultaneously press the and
instructions which appear on the screen. You will then be able to
look at the installer code which the element has recorded in it (in
this case 02).
If the memory card is a Mini-A.C. Unit card, the screen will also
show its password number (in this case 0111. The zero on the left
appears by default because the password for Mini-A.C. Unit
memory cards has three digits.).
If the memory card is a Maxi-A.C. Unit card, the screen will show its password and the
communication password (if you are communicating with a PC-CARD)
and you will see the following on the screen
and you will see the following on the screen
MANAGER Portable Programmer+DCS
ramming for distributors
keys and follow the
keys and follow the
Loading...