JCM Connect Receiver User Manual

1247002-GB_v1.1

Alimentación 12V dc Alimentation 12V dc 12V dc supply Stromversorgung 12V dc

Salida señal decodificada (C4+ / Clock / D0 Wiegand) Sortie signal décodé (C4+ / Clock / D0 Wiegand) Decoded signal output (C4+ / Clock / D0 Wiegand) Ausgang dekodiertes Signal (C4+ / Clock / D0 Wiegand)

Salida señal decodificada (Data / D1 Wiegand) Sortie signal décodé (Data / D1 Wiegand) Decoded signal output (Data / D1 Wiegand)

Ausgang dekodiertes Signal (Data / D1 Wiegand)

Contacto detector magnético canales 1 y 3 Contact détecteur magnétique canaux 1 et 3 Magnetic detector contact channels 1 and 3 Magnetdetektorkontakt Kanal 1 und 3

Contacto detector magnético canales 2 y 4 Contact détecteur magnétique canaux 2 et 4 Magnetic detector contact channels 2 and 4 Magnetdetektorkontakt Kanal 2 und 4

Común contactos Contacts communs Contact common Gemeinsame Kontakte

CONNECT

Multiprotocol receiver compatible with MOTION range transmitters. Codifies the transmitter signal in four different protocols according to its configuration: C4+, Clock&Data, Wiegand 26 and Wiegand 37.

1247002-GB_v1.1

Power supply

12V dc (9Vdc-21Vdc)

Frequency

868,35MHz

Consumption standby / operating

14mA/36mA

Operating temperature

-20ºC to +85ºC

Watertightness

IP54 (with glands IP65)

Dimensions

82x190x40mm

Protocol

Alimentation

Sortie signal

PROTOCOLE

SW1

PROTOCOLE

SW2

Format

C4+

+ - S OFF

OFF

---

Clock&Data

+ -

S=CLOCK and L=DATA

OFF

8 BCD digits

Wiegand 26

+ -

D0 and D1

OFF

8 bits site code + 16

bits code /

4 bits (zeros)+ 20 bits

code*

Wiegand 37

+ -

D0 and D1

---

APB SW1

APB SW2

Function

Canal 1

Canal 2

Canal 3

Canal 4

OFF

Multichannel

OFF

Multichannel

OFF

Monochannel*

1 C open

2 C open

Monochannel*

1 C open

2 C open

CONNECT

1. TECHNICAL CHARACTERISTICS

2. INSTALLATION AND CONNECTIONS

Attach the rear part of the chassis to the wall using the plugs and screws supplied. Pass the cables through the bottom of the receiver. Connect the power cables to the terminals marked in the mother board, as indicated. Mount the receiver front and pass the cables and the antenna through it.

3. OPERATING

3.1. CONFIGURATION AND CONNECTION FOR THE DIFFERENT PROTOCOLS

* formats configurable with the ASSISTANT

Note: To use other protocols, contact the manufacturer.

3.2. OPERATING MODES

* If both contacts are open or closed, no code is sent.

A) MULTICHANNEL MODE (ANTIPASSBACK NOT ALLOWED)

The interface operates as a decoder-receiver. Terminals 1 2 C are not enabled.

B) MONOCHANNEL MODE (ANTIPASSBACK FUNCTION ALLOWED)

Magnetic detectors must be used for antipassback function to be able to distinguish the entry and exit of vehicles to and from an installation. Terminals 1 2 C are used for connecting the detectors. To validate entry access, one must be located on the entry loop and press the entry transmitter channel at the same time. To validate exit access, one must be located on the exit loop and press the exit transmitter channel at the same time.

+ 2 hidden pages