BS EN ISO9001 - 2015 - Registered Firm Certificate No. GB 1552
Important warranty information
This product is supported by a 2-year standard warranty which will extend to 5-years if registered within the first year of pu
Please register at jcc.co.uk/warranty (Terms and conditions apply).
The installer will be asked to provide the following information, which is detailed on a label attached to the luminaire’s chas
Product Code/Date Code.
company
Toughbay™RetrotRange
Live (+)
blue
Switched Live (Brown)
Neutral (Blue)
Wire preparation
Installation instructions for LED Highbay
WARNINGS AND CAUTIONS
a
• It is recommended that luminaires are installed by a qualied
electrician to ensure the installation complies with the local current
wiring regulations.
• Any broken or damaged parts should be replaced as soon as possible.
JCC will not accept responsibility for claims arising from
sub-standard installations.
• Caution. Risk of electric shock
• The external exible cable or cord of this luminaire cannot be
replaced; if the cord is damaged the luminaire shall be destroyed.
INSTALLATION
Specications Colour Temp: 4000K*/5700K Ra: 80
Wattage Lumens LpcW Beam
100W 12300 123 60°/90°/120°
150W* 18400 123 60°/90°/120°
200W 24500 123 60°/90°/120°
Available nishes: Black only
Terminal block must comply to EN 60998-2-1 or EN 60998-2-2
Standard version connection
220-240V~ 50/60Hz / Class I
Figure 1. Mains input
brown
Earth
yellow/green
Neutral (-)
• These products are designed for connection to a 220-240V~
50/60Hz supply.
• This luminaire is suitable for indoor and outdoor use.
• It may be necessary to upgrade your MCBs to allow for increased
inrush current.
• This luminaire should be installed out of arms reach.
• Terminal block not included. Installation may require advice from a
qualified person.
• It is recommended that the ambient room temperature should not
exceed 60°C.
ENGLISH
• Read instructions and check that you have all of the tools and
accessories required to complete the installation correctly. Isolate
power supply before starting the installation.
Standard dimmable version installation procedure
1. The luminaire comes with a xed eye(s) for suspension as standard.
2. For surface mounting please order correct bracket separately (see
table below for details). Fit the bracket to a at surface ensuring
that xings are suitable to hold the weight of the luminaire. Fit the
luminaire to the bracket using the bolts supplied.
3. Connect the mains input as shown in Fig.1, using a suitable
connector to maintain the IP rating for the location.(not supplied).
Please ensure that 3-core H07 RN-F cable is used.
4. This luminaire is 1-10V dimmable as standard, if you wish to dim this
tting ensure that you connect the 1-10V dimming control wires
as shown in Fig.3 to a 1-10V dimming system only. If no dimming is
required please leave the terminals isolated.
Emergency dimmable version installation procedure
Emergency version connection
220-240V 50/60Hz / Class I
Figure 2.
1.0-1.5mm
Un/Switched Live (Black)
Earth (Green/Yellow)
1-10V Dimming control input
Figure 3.
Dim - (white)
Dim + (Black)
25mm
8mm
1. Follow steps 1-2 of the standard installation procedure.
2. Connect the mains input as shown in Fig.2, using the connector
( supplied). Please ensure that 4-core H07 RN-F cable is used. To
identify the correct terminals for mains input, unscrew/loosen
the collar to expose the cables and match the connections to the
corresponding colours in Fig.2
3. Once the mains supply is connected and the tting is installed,
connect batteries. The LED charge indicator will illuminate showing
the tting is in charge mode and is working correctly. Allow 24hrs
for the batteries to charge prior to testing in emergency mode.
4. This luminaire is 1-10V dimmable as standard, if you wish to dim this
tting ensure that you connect the 1-10V dimming control wires
as shown in Fig.3 to a 1-10V dimming system only. If no dimming is
required please leave the terminals isolated.
Accessories
JC040049* Surface Mount Bracket for 100/150/200W Toughbay Retrot G2
*not suitable for EM and MW versions
You can help protect the environment. Please remember to respect the local regulations: hand in the non-working electrical equipment to an appropriate
waste disposal centre. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the
recyclable material collection service.
RoHS
Compliant
IP65
jcc.co.uk
JCC Lighting Products Ltd. Lux Park, Chichester Business Park, City Fields Way, Tangmere, Chichester, West Sussex, PO20 2FT
Technical Support: +44(0)1243 838986 Customer Services: +44(0)1243 838999
rchase.
sis:
V
10_Dec_2022_RS
Prole&Dimensions
All dimensions in millimetres
270.9
260
160
1-10V Dim
279.7
100W 150W
M/W Dim
260
165.5
354
367.7
270.9
280
163
280
1-10V Dim
280
167.0
283.9
280
M/W Dim
373.1
378.4
320
170
320
1-10V Dim
200W
M/W Dim
413.0
320
170
413.0
320
186.2
1-10V dim EM
186.2
353.2
M/W Dim EM
189.9
1-10V dim EM
X
167.0
373.1
M/W Dim EM
196.6
1-10V dim EM
197.4
M/W Dim EM
Loading...