Page 1
User guide
1400W
20L Wet & Dry
Vacuum Cleaner
70340
Page 2
1400W 20L Wet & Dry Vacuum Cleaner 70340
Thank you for purchasing this JCB product
JCB is a byword around the world for quality, innovation and success.
With the application of stringent design parameters and utilising high performance,
modern materials and manufacturing processes, your JCB product has been developed
for optimum functionality and practical application.
Used for the purposes for which it is intended, and with careful maintenance as outlined in
this user guide, your JCB product will give years of trouble-free service.
2
IMPORTANT
Please read all of the product safety and operating instructions carefully before using this product.
Please pay particular to all sections of this user guide that carry warning symbols and notices.
WARNING!
This is a Warning symbol. This symbol is used throughout the user guide
whenever there is a risk of personal injury. Ensure that these warnings are read
and understood at all times.
CAUTION!
This is a Caution symbol. This symbol is used throughout the user guide whenever there
is a risk of damaging your JCB product. Ensure that these warnings are read and
understood at all times.
NOTE:
Used throughout the user guide to provide additional information, hints and tips.
Our products are continually monitored to comply with changing technical standards and requirements.
The company reserves the right to alter design and specifications without prior notice. E. & O. E. errors
and omissions exempted.
Page 3
3
CONTENTS
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
OVERVIEW OF THE APPLIANCE COMPONENTS . . . . . . . . . . . . . 5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DRY VACUUM CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WET PICK-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TOOLS AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ADDRESS AND HELPLINE NUMBER . . . . . . . . . . . . . . . . . . . . . . . 11
GUARANTEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Page 4
4
SAFETY INSTRUCTIONS
Personal safety
• WARNING!: When using
this vacuum cleaner, basic safety
precautions, including the
following, should be followed
to reduce the risk of personal
injury and material damage.
Read all of this User Guide
before using this vacuum
cleaner.
• Never use in the presence of explosive
liquid or vapours.
• Never pick up inflammable or poisonous
liquids such as petrol, copier toner or
other volatile substances.
• Never pick up acids, asbestos or asbestos
dust.
• Never touch the plug or cable with wet
hands.
• Unprofessional repairs can be dangerous
for users.
• The appliance must never be left running
unsupervised.
• This appliance is intended for domestic
use only.
• Misuse or use for commercial or any
other purpose will render the guarantee
invalid.
• Always disconnect from the main supply
after use or prior to emptying, cleaning or
maintaining the appliance.
• To protect against fire, electric shock and
personal injury, do not immerse cord, plug
or cleaner in water or other liquid.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
Children
• Children do not understand the dangers
associated with operating electrical
appliances. Never allow children to use
this appliance.
• Children should be supervised to ensure
that they do not play with the appliance,
or stumble over the power cord.
Product safety
• CAUTION!: Never use the
appliance without a filter being
installed.
• CAUTION!:
Never use the
appliance to vacuum hot ashes, large
pieces of broken glass or sharp
objects.
• Use only JCB approved spare parts and
accessories.
• Never modify the cleaner in any way.
Location
• Do not use or keep this product outside.
• Do not store the appliance near hot
surfaces eg. ovens or heating appliances.
Mains lead
• Do not allow the mains lead to become
strained or run this appliance over it.
• If the electrical cable becomes damaged
the cable assembly must be replaced. Do
not attempt this task yourself, contact the
Helpline number that is found on page 11.
Electrical requirements
• Check that the voltage on the rating plate
of your appliance corresponds with your
house electricity supply which must be
A.C. (Alternating Current).
• If the socket outlets in your home are not
suitable for the plug supplied with this
appliance the plug should be removed and
the appropriate one fitted.
• WARNING!: The plug removed
from the mains lead, if severed,
must be destroyed, as a plug
with a bared flexible cord is
hazardous if engaged into a live
socket outlet.
• Should the fuse in the 13 amp plug require
changing, a 13 amp BS1362 fuse must be
fitted.
Page 5
16
1
2
3
4
6
7
8
9
10
11
12
13
14
15
17
19
5
18
OVERVIEW OF THE APPLIANCE COMPONENTS
1 Carry handle 11 Pleated filter
2 Motor housing 12 Float switch
3 Float cage 13 ON/OFF switch
4 Anti-crush hose 14 4 x castors
5 Wet pick up / large particle floor nozzle 15 Tank
6 2 x metal tubes with parking hook 16 Clamps (x2)
7 Crevice tool 17 Connection for the anti-crush hose
8 Upholstery nozzle 18 2 position wheeled floor nozzle
9 Foam mesh filter 19 Hose handle with suction control valve
10 Paper dust bag
5
Page 6
6
ASSEMBLY
1. Make sure that the appliance is not
plugged in.
2. Hold the two clamps, which hold the
motor housing in its position and fold
them upwards A.
3. Loosen the clamps and lift the motor
housing up and out B.
4. Turn the tank over so that the motor
housing is on the bottom.
5. Put the four castors Á into the holes on
the bottom of the tank C.
16
1
6
9
10
11
15
17
19
18
6. Firmly push the castors down until they
lock into position, then turn the tank over.
NOTE: Take care not to damage
the tank by applying excess force.
7. Fit the appropriate filter or bag. See later
sections.
8. Replace the motor housing on the tank
D.
9. Hook the clamps into the motor housing
and let them snap into place by pressing
the clamps downwards E.
10. Screw the large end of the hose › on the
front air intake stub Í on the tank F.
11. Place the hose handle Ï on the hose ›
by pushing it into place.
12. Select a nozzle fi ‡ · Î or the
two metal tubes fl and slide it over the
suction tube › G.
16
1
15
17
B
A
C
D
E
F
G
Page 7
7
DRY VACUUM CLEANING
Pleated filter ‰
For dry vacuuming, when picking up large
particles, the pleated filter may be used by
itself, no dust bag is needed. After use, the filter
may be gently brushed or tapped to remove
dust. The pleated filter ‰ cannot be washed
and should not be used for wet pick-up.
The product is supplied with the pleated filter
‰ fitted. To remove, eg. when using for wet
pick-up, pull gently H.
Paper dust bag „
When picking up fine dust, we recommend the
paper bag should be fitted in addition to the
pleated filter. This stops the filter clogging and
makes disposal of the dust easier. Do not use
the paper bag for wet pick up.
Fitting the paper dust bag
Slide the paper dust bag „ over the hose inlet
connection in the tank I.
Press it until it locates firmly into place all
around the connector J.
NOTE: Opening the bag out a little
and bending the creases on the
cardboard will ease the fitting. Take
care not to damage the dust bag.
Check the dust bag „ regularly and change it
when it is 2/3 full. If fine dust has been picked
up, the bag may need to be changed sooner as
the pores of the bag may become blocked. The
dust bag is not reuseable.
NOTE: Don’t use the dust bag for
vacuuming up objects with sharp
edges or wet objects.
Place the motor housing on the tank D and
close the clamps E.
Screw the large end of the hose on the front air
intake stub Í on the tank F.
Make sure that the ON/OFF switch Ê on the
appliance is in the “Off” position (position “0”)
before you plug the power plug into the socket.
Plug the power plug into the socket.
Switch the motor on (ON/OFF switch in
position “I”).
When you have finished vacuuming, switch the
motor off by putting the ON/OFF switch Ê
into the “OFF” position (position “O”).
Unplug the power plug.
H
I
J
Page 8
8
WET PICK-UP
NOTE: Never vacuum up
hazardous materials.
Foam mesh filter ‚
For wet pick-up, the foam mesh filter must be
fitted.
Make sure that the appliance is not plugged into
the power mains.
Check to make sure that the tank Ë is free of
dust and dirt.
Remove the paper dust bag „ and/or the
pleated filter ‰. Slide the foam mesh filter ‚
K over the filter basket.
Place the motor housing on the tank D and
close the clamps E.
NOTE: If you want to vacuum up
a large quantity of liquid from a sink
or a tank, please don’t put the entire
suction nozzle in the liquid; rather
leave a little space so that some
air can also be drawn in along with
the liquid.
The appliance is equipped with a float switch
 that will stop the vacuuming when the tank
is full. You will notice that suction has stopped
by the motor now running faster. In this event,
switch the appliance off and unplug it.
Be aware that the full tank can be very heavy.
In this event, remove the motor housing from
the tank B and pour the rest of the liquid into
a suitable tank or drain. Then you can continue
vacuuming after you have replaced the motor
housing D.
After wet vacuuming, switch off the appliance
and unplug it. Empty the container and clean/
dry it inside and outside.
TOOLS AND
ACCESSORIES
Hose handle with suction control
valve Ï
Fit this between the hose and tubes. This gives
additional length to the tube and allows control
of the suction. Rotate the valve to open. With
the valve open, the suction to the nozzle will be
reduced making it easier to push. For maximum
suction, have the valve fully closed.
2-position wheeled floor nozzle Î
Use this nozzle for dry vacuum cleaning large
areas of floor when the particles are small to
medium sized.
Use with the brushes down on hard floors and
up on carpets. Press the foot pedal to lower or
raise the brushes as required.
Wet pick-up/large particle nozzle fi
Use this nozzle, with the brushes and flexible
strip attached, for wet vacuum cleaning floors.
When picking up larger particles, the brush
and flexible strip section of the nozzle may be
removed by pressing the clips at either end of
the nozzle.
Upholstery nozzle ·
This may be used with either wet or dry
vacuuming and is intended for smaller areas
such as furniture.
Crevice tool ‡
This may be used with either wet or dry
vacuuming and is useful for small gaps and when
high spot suction is required.
Anti-crush hose ›
Avoid picking up very large particles, especially
when using the hose without a nozzle, as these
may become trapped in the hose.
K
Page 9
9
Two metal tubes with parking hook fl
The two metal tubes simply push together.
The lower tube has a parking hook so that the
hose/tube assembly can be parked during use.
The parking hook slots into the U clip on the
motor housing. The parking hook position on
the tube is designed to suit the 2-position floor
nozzle, however the position of the parking
hook may be adjusted to suit the other nozzles
if required.
Loosen the two screws and slide to new
position and then re-tighten the screws.
STORAGE
The tools and accessories may be stored on the
storage section at the rear of the product L.
16
1
9
10
11
15
17
19
To store the 2-position wheeled floor nozzle,
attach to the lower tube and then place in the
parking position.
MAINTENANCE
Remove the mains plug before carrying out any
maintenance.
After using for wet pick-up, empty the
container, wash the foam mesh filter ‚ (in
clean cool water) and leave the container open
to fully dry before re-assembling.
With the filter removed, regularly check the
operation of the float. This must be able to
move freely to shut-off the suction when the
maximum quantity of water is picked up M.
16
1
9
10
11
15
17
19
L
M
Page 10
10
TROUBLESHOOTING
Problem Possible causes Possible solutions
Poor suction Pleated filter clogged
Dust bag clogged (Note: fine dust
may clog the pores of the bag even
if it does not appear full)
Float shut-off valve has operated.
This operates when the maximum
quantity of water has been reached
but it may also operate if the
cleaner is knocked over
Blockage in hose, tubes or nozzle
Gently brush clean or replace
Replace bag
Switch the product off and empty
or if the product has been knocked
over, return the product to upright
Check for blockage and remove
Water escapes from
the exhaust
Float valve is jammed by
obstruction
When picking up a large volume
of liquid do not fully immerse the
nozzle in the liquid, allow some air
intake to ensure correct operation
of the float valve
Check operation of valve, ensure
foam mesh filter is fitted correctly
Dust escapes from
exhaust
Check condition of the bag and
pleated filter
Replace if necessary
Page 11
11
HELPLINE
If you have any difficulty with your appliance, do
not hesitate to call us.
We are more likely to be able to help than the
store from where you bought it.
Please have the following information ready to
enable our staff to deal with your query quickly.
• Name of the product
• Model number as shown on the rear of
the appliance
• Serial number as shown on the rating label
UK Helpline and Replacement Parts:
0844 871 0961
ADDRESS
JCB.
Mexborough,
South Yorkshire,
England,
S64 8AJ
Page 12
It is important to retain the retailer’s receipt as
proof of purchase. Staple your receipt to this
back cover for future reference.
Please quote the following information if the
product develops a fault. These numbers can
be found on the base of the product.
Model no.
Serial no.
All JCB products are individually tested before
leaving the factory. In the unlikely event of any
appliance proving to be faulty within 28 days of
purchase, it should be returned to the place of
purchase for it to be replaced.
If the fault develops after 28 days and within 3
years of original purchase, you should contact
the Helpline number quoting Model number
and Serial number on the product, or write to
JCB at the address shown.
You may be asked to return a copy of proof
of purchase. Subject to the exclusions set out
below, the faulty appliance will then be repaired
or replaced and dispatched usually within 7
working days of receipt.
If you suspect a fault, follow the simple checks
detailed below before retrying the appliance or
calling the helpline.
• Replace bag.
• Check the tools / tubes / hose for
blockages.
• Check the plug is firmly in the socket.
• Check the socket is working by trying
another appliance.
• Check the fuse in the plug.
If for any reason this item is replaced during the
3 year guarantee period, the guarantee on the
new item will be calculated from the original
purchase date.
Therefore it is vital to retain your original till
receipt or invoice to indicate the date of initial
purchase.
To qualify for the 3 year guarantee, the
appliance must have been used according to the
instructions supplied.
Exclusions
JCB shall not be liable to replace or repair the
goods under the terms of the guarantee where:
1. The fault has been caused or is
attributable to accidental use, misuse,
negligent use or used contrary to the
manufacturer’s recommendations or
where the fault has been caused by power
surges or damage caused in transit.
2. The appliance has been used on a voltage
supply other than that stamped on the
products.
3. Repairs have been attempted by persons
other than our service staff (or authorised
dealer).
4. Where the appliance has been used for
hire purposes or non domestic use.
5. JCB are not liable to carry out any type of
servicing work, under the guarantee.
6. The guarantee excludes consumables such
as bags and filters.
• This guarantee does not confer any
rights other than those expressly set out
above and does not cover any claims
for consequential loss or damage. This
guarantee is offered as an additional
benefit and does not affect your statutory
rights as a consumer.
VC70340 MUK Rev1 09/10
This JCB product is intended for household use only.
JCB has a policy of continuous improvement in product
quality and design. The company, therefore, reserves the
right to change the specification of its models at any time.
For electrical products sold within the European
Community. At the end of the electrical product’s useful
life, it should not be disposed of with household waste.
Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice in your
country.
GUARANTEE
12
JCB is used under license.
Loading...