JB Systems Accu Color User manual

ENGLISH USER MANUAL

OPERATION MANUAL

Thank you for buying this JB Systems® product. To take full advanta ge of all possibilities an d for your own
safety, please read these operati ng instr uct ions ver y caref ully before you start using this unit.

FEATURES

• Battery operated LED-projector, based on 6pcs 10Watt RGBWA-LEDs to avoid unwanted color shadows.

• Beam angle = 22°

• Projection angle can be adjusted over 25° (vertical to horizontal)

• The perfect solution for many applications: exhibition booths, parties, special events , ...

• +/-10hrs use in fading mode on a fully charged battery!

• Each projector is equip ped with a wireless trans ceiver module (transmitter and receiv er) which is 100%

compatible with the W-DMX G4-protocol from “Wireless Solution Sweden”.

• Projector can still be used with empty battery: just connect it to the mains!

• Very smooth RGBWA color changes thanks to high freq. dimming electronics

• The internal battery charger charges the battery while the projector is working on mains power.

• The projector comes with a transparent plastic cover to protect it against rain (IP20) so it can be used

outdoor to light up trees, plants, walkways,…

• Different working modes:

• Standalone: custom colors selectable or automatic and beat synchronized color changes

• Master/slave mode: wonderful preprogrammed, music synchronized lightshows.

• DMX-controlled : cabled and wireless. (5 modes : 4-5-9-10 channels, LEDCON-02 Mk2)

• Controlled by a small JBS LEDCON-02 Mk2 and LEDCON-XL controller

• Controlled by wireless IR remote control

• ProCon mains in/outputs: easy daisy chaining of several units (if needed).

BEFORE USE

• Before you start using this unit, pleas e check if there’s no trans portation dam age. Should there b e any, do
not use the device and consult your dealer first.

• Important: This device left our f actory in perfect condition and well packaged. It is absolut ely necessary
for the user to stric tly foll ow the s afety instr uctions and warn ings in th is user m anual. Any dam age caused
by mishandling is not subje ct to warrant y. The dea ler will not accept responsibi lity for an y result ing d efects
or problems caused by disregarding this user manual.

• Keep this booklet in a safe plac e for future consultation. If you sell the fixture, be sure to add this user
manual.

Check the contents:

Check that the packing contains the following items:

• Operating instructions

• Accu Color

• Mains cable

• Wireless IR remote control

• Transparant plastic cover

JB Systems® 1/13 Accu Color

ENGLISH USER MANUAL

CAUTION: T o reduce the risk of electric shock , do not remove
to qualified service personnel only.

This symbol means: indoor use only
IP43 outdoor while used with the optional cover

This symbol determines: the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 1 meters

SAFETY INSTRUCTIONS:

the top cover. No user-ser viceable parts inside. Refer servicing

The lightning flash with arro whead symbol within the equilateral trian gle is intended to alert the
use or the presenc e of un-insulated “dangero us voltag e” withi n the prod uct’s enc losure th at ma y
be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equ ilateral triang le is intended to aler t the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.

This symbol means: Read instructions

The device is not suitabl e for direct mountin g on normally flamm able surfaces . (suitable only for
mounting on non-combustible surfaces)

CAUTION: Do not stare at operating lamp.
May be harmful to the eyes.

• To protect the environment, please try to recycle the packing material as much as possible.

• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

• To avoid condensati on to be formed ins ide, allow the unit to adapt to the s urrounding tem peratures when

bringing it into a warm room after transport. Condense som etimes prevents the unit from work ing at full
performance or may even cause damages.

• This unit is for indoor use only.

• Don’t place metal obj ects or s pill liqu id insi de the unit. Electr ic shoc k or malf unction m a y result. If a f oreign

object enters the unit, immediately disconnect the mains power.

• Locate the fixture in a well ventilated spot, away from any flammable m aterials and/or liqu ids. The fixture
must be fixed at least 50cm from surrounding walls.

• Don’t cover any ventilation openings as this may result in overheating.

• Prevent use in dusty environments and clean the unit regularly.

• Keep the unit away from children.

• Inexperienced persons should not operate this device.

• Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.

• Make sure the area below the i nstallation place is free from unwanted persons during rigging, de-rigging

and servicing.

• Allow the device about 10 minutes to cool down before to start servicing.

• Always unplug the unit when it is not used for a longer time or before to start servicing.

• The electrical instal lation should be car ried out by qualifie d personal only, acc ording to the regul ations for

electrical and mechanical safety in your country.

• Check that the available voltage is not higher than the one stated on the unit.

• The power cord should alw a ys be in perfect condition. Switch the un it im mediately off when the power cor d

is squashed or damaged. It must be replaced b y the manufacturer, it’s ser vice agent or similarly qualified
persons in order to avoid a hazard.

• Never let the power-cord come into contact with other cables!

• This fixture must be earthed in order to comply with safety regulations.

• Don’t connect the unit to any dimmer pack.

• Always use an appropriate and certified safety cable when installing the unit.

• In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.

• Never repair a fus e or bypass the fuse holder. Always replac e a damaged fuse with a f use of the same

type and electrical specifications!

• In the event of serious operating problems, stop using the fixture and contact your dealer immediately.

• The housing and the lenses must be replaced if they are visibl y dam aged.

• Please use the original pack ing when the device is to be transpor ted .

JB Systems® 2/13 Accu Color

ENGLISH USER MANUAL

• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look direc tly into t he light so urce! Don’t us e the eff ect in th e presence of per sons s uff ering
from epilepsy.

DESCRIPTION:

1. Antenna for wireless connection

2. Handle to easily carry the projector.

3. Lens in front of RGBWA 10W LED

4. Knob used to fasten the projector in a desired angle between 0° and 25°.

5. Projector base.

6. DMX Output connector XLR Female 3P.

7. DMX Input connector XLR Male 3P.

8. Mains output with ProCon connector : you can use a spec ial XLR/P owerc on cabl e to connect up to m ax.

16A (power).

9. Mains input with ProCon connector : you can use a spec ial XLR/ Powercon c able to connect u p to m ax.

16A (power).

10. Fuse holder with glass fuse: replace with the correct fuse, see technical information

11. Hole to use the base as hanging bracket to fix the projector in truss, using a mounting hook.

12. IR sensor

13. [ID-Set] button : used to connect projector wireless to another projector. (see chapter : [HOW TO

SETUP])

14. Test button : push this button to check the battery status (25 – 50 – 75 or 100% charged)

15. [Wireless DMX] Indicator : shows the wireless status (see chapter : [HOW TO SETUP])

16. Microphone : allows the projector to work in audio-mode.

17. [Power ON/OFF] button : push this button to turn the projector ON or OFF

18. Audio sensitivity button : turn this button left or right to adjust the microphone’s sensitivity to sound.

19. [MENU] button : push this button to select the desired topic in the menu

20. ▲ button : push this button to go up in the menu

21. Display

22. ▼ button : push this button to go down in the menu

23. [ENTER] button : push this button to confirm the selected setting

24. [Wireless ON/O FF] button : push this button to s witch ON or OFF the wireless transmitter /receiver in t he

projector.

JB Systems® 3/13 Accu Color