JBL CINEMA SOUND
SPEAKERS
CS480
OWNER’S GUIDE
®
I
MPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket or
table specified by the manufacturer or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, or the apparatus has
been exposed to rain or moisture, does not operate normally or
has been dropped.
15. Do not expose this apparatus to dripping or splashing and
ensure that no objects filled with liquids, such as vases, are
placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains,
disconnect the power supply cord plug from the AC receptacle.
17. The mains plug of the power supply cord shall remain readily
operable.
18. Do not expose batteries to excessive heat such as sunshine,
fire or the like.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the product.
WARNING: T
expose this apparatus to rain or moisture.
o reduce the risk of fire or electric shock, do not
3
Left
Surround
Channel
Right
Surround
Channel
Left Front
Channel
Subwoofer
R
ight Front
C
hannel
C
enter
Channel
Couch
Left
Surround
Channel
Right
Surround
Channel
Left Front
C
hannel
Subwoofer
Right Front
C
hannel
Center
Channel
T
®
®
®
®
®
®
®
®
®
®
®
®
®
HANK YOU FOR CHOOSING JBL
or more than 60 years, JBL has been involved in every aspect of
F
music and film recording and reproduction, from live performances
to the recordings you play in your home, car or office.
We’re confident that the JBL system you have chosen will provide
every note of enjoyment that you expected – and that when you think
about purchasing additional audio equipment for your home, car or
office, you will once again choose JBL.
Please take a moment to register your product on our Web site at
www.jbl.com. It enables us to keep you
posted on our latest advancements, and helps us to better understand our customers and build
products that meet their needs and expectations.
INCLUDED
Carefully unpack the system. If you suspect damage from transit, report it
immediately to your dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Open the package and verify the
following contents:
P
LANNING YOUR SYSTEM
efore deciding where to best place your speakers, survey your room
B
and study Figures 1 and 2.
Figure 1. In this overhead view of a typical installation, satellite
speakers are used to reproduce sound for the front and surround
channels. The center channel reproduces sound and dialogue.
The powered subwoofer provides bass for effects and music.
(1) Subwoofer
(4) Satellite speakers
(5) Adjustable wall brackets for satellites and
center channel with tightening bar
(4) Wall brackets for satellites
(1) Center with base
Figure 2. This figure shows an alternative layout, which may be
more suitable for some rooms.
(1) Wall bracket for center channel
4
P
LACEMENT
eft and Right Front Channels
L
For left and right front channels, place one satellite to the left
and another to the right of the television, as shown in Figure 1.
Since the speakers are magnetically shielded, you can place
them very close to the TV without worrying about the magnetic
field distorting the picture.
Center Channel
For the center channel, place the speaker directly on top of,
or below, your television. Use a shelf or one of the included wall
brackets if the television does not provide a stable platform.
Surround Channels
For left and right surround channels, place one speaker on the left
and another on the right, to the side of or slightly behind the listening
area. The surround speakers should be mounted at a height of
between 5 ft. (1.5m) and 7 ft. (2m).
Subwoofer
Since the installation of a subwoofer can be somewhat more complicated than installing full-range speakers, it is essential that you read
this section very carefully prior to connecting the subwoofer to your
system. Should you have questions relating to installation, it is advisable to call either your dealer or JBL’s Customer Service Department
for advice.
The performance of the subwoofer is directly related to its placement
in the listening room and how the subwoofer is aligned with the
satellite speakers. Setting the volume of the subwoofer in relation
to the left and right speakers is also of critical importance because
it’s essential that the subwoofer integrate smoothly with the entire
system. Setting the subwoofer’s volume level too high will result in
an overpowering, boomy bass. Setting the volume level too low will
negate the benefits of the subwoofer.
Here are several additional facts on installation that may prove use
ful. It is generally believed that low frequencies (below 125Hz) are
nondirectional and, therefore, placement of a subwoofer within any
listening room is not critical. While in theory it is true that the larger
wavelengths of extremely low frequencies are basically nondirectional, the fact is that, when installing a subwoofer within the limited
confines of a room, reflections, standing waves and absorptions generated within the room will strongly influence the performance of any
subwoofer system. As a result, specific location of the subwoofer
becomes important, and we strongly recommend that you experiment
with placement before choosing a final location. Placement will
depend upon your room (for example, whether or not your room
permits placement of the subwoofer near either satellite) and the
amount and quality of bass required.
-
5
Metal bar
Metal bar
®
A
B
C
W
ALL-M
A
ND CENTER CHANNEL
OUNTING THE SATELLITES
The CS480 satellites and center channel are designed to be mounted
n the wall. There is a fixed-mount wall bracket and an adjustable
o
wall bracket provided for each satellite and the center channel. Each
peaker bracket will require up to four 1-1/2"#10
s
ood screws; each
w
screw should be fastened to a wall stud. If a wall stud is unavailable,
install an anchor appropriate for a 1-1/2"
#10 screw.
NOTE: The customer is responsible for the correct selection
and use of mounting hardware (available through hardware stores)
that will ensure the proper and safe wall-mounting of the speakers.
Fixed-Mount Wall Bracket
Step 1. Mark the positions on the wall where you would like to
lace the mounting screws.
p
Step 2. Attach the bracket to the wall using two screws
(not included).
Step 3. Remove the rubber ring on the bottom of the satellite and
seat the satellite or center channel speaker onto the back bracket.
Step 4. Attach the 1/4-20 screw into the insert on the bottom of the
speaker and tighten.
djustable Wall Bracket
A
tep 1.Remove the cap over the threaded insert on the rear of the
S
speaker.
Step 2. Mark the positions on the wall where you would like to place
the mounting screws.
Step 3. Place the bracket against the wall and fasten four 1-1/2" #10
wood screws (not included) through the bracket’s screw holes into
the wall. If a wall stud is not available, use an appropriate anchor.
Step 4. Unscrew the round collar (C) from the bracket (A).
Step 5. Screw the ball and shaft assembly (B) to the 1/4"-20 insert on the
back of the satellite or the center channel (do not use the bottom insert
on either speaker). Back out 1/2 of a turn and tighten the nut against the
speaker. If the ball and shaft assembly is not backed out before tightening the nut, performing Step 8 below may dislodge the threaded insert in
the speaker housing and permanently damage the speaker.
Step 6. Attach the speaker wire as shown on page 7.
Step 7. Drop the round collar (C) over the ball and shaft assembly
(B) that is mounted to the speaker with the finished side of the collar
facing the rear of the speaker.
Step 8. Carefully push the ball straight into the socket mounted on the
wall, angle the speaker as desired and tighten the collar using the
enclosed metal bar.
6
Figure 3. Bracket on wall.
C
ENTER AND SATELLITE SPEAKER
C
ONNECTIONS
Turn Off All Power
fter placing the speakers, you are ready to connect your system.
A
First, turn off all audio-system power. Use high-quality speaker wire
o make your connections (#18-gauge speaker wire with polarity
t
coding is included). For longer distances, #16-gauge or heavier wire
is recommended. The side of the wire with a ridge or other coding is
usually considered positive (+) polarity. Also, consult the owner’s
manuals that were included with your amplifier or receiver to confirm
connection procedures.
Satellites
Observe polarities when making speaker connections, as shown
in Figure 4. Connect each + terminal on the back of the amplifier or
receiver to the respective + (red) terminal on each speaker. Connect
he – (black) terminals in the same way.
t
Important!
Do not reverse polarities (i.e., + to –, or – to +) when making
connections. Doing so will cause poor imaging and diminished
bass response. Be certain that positive and negative wire strands
are completely isolated to avoid short circuits that may damage
your equipment.
enter Channel
C
Observe polarities when making speaker connections, as shown
n Figure 5. Connect each + terminal on the back of the amplifier or
i
receiver to the respective + (red) terminal on the speaker. Connect
he – (black) terminals in the same way.
t
mportant!
I
Do not reverse polarities (i.e., + to –, or – to +) when making
onnections. Be certain that positive and negative wire strands are
c
completely isolated to avoid short circuits that may damage your
equipment.
NOTE: On certain models using hexagonal terminal nuts, a small
socket wrench is provided to help in properly tightening the terminals.
Hand-tighten only and do not overtighten.
Figure 4. Wiring diagram shows polarity connections
for one channel of a home theater system.
Figure 5. The satellites and center channel
speaker feature terminals that can be connected
– e.g.,
in several different way
and direct wiring (as shown here).
s
spade terminals
7
S
PHASE
CS80SUB
¡
™
£
¢
∞
§
FUSE
T 2.5A L 250V
120V–60Hz
200Watts
SUBWOOFER OR
L
FE OUTPUT
R
ECEIVER/PROCESSOR
RECEIVER/PROCESSOR
UBWOOFER CONTROLS
ear Panel
R
ubwoofer Connections
S
If you have a Dolby®Digital or DTS®receiver/processor with
a low-frequency-effects (LFE) or subwoofer output:
15' (4.5m)
Subwoofer
cable included
If your receiver/processor does not contain a Dolby Digital or DTS
processor but has a subwoofer output:
1
Subwoofer-Level Control
2
Phase Switch
3
LFE Input
4
Line-Level Inputs
5
Power Indicator LED
6
Power Switch
15' (4.5m)
Subwoofer cable
included
NOTE
: If your receiver/processor has only one sub out, you may use
either the L or R input.
Important!
AYS TURN OFF ALL
Whenever changing cables, pulling plugs, etc., AL
W
EQUIPMENT, including the subwoofer.
8
O
PERATION
urround Modes
S
When using the CS480 in a Dolby Digital or DTS home theater system,
make sure all speakers are set to “Small”. In a Dolby Pro Logic
®
home
theater system, make sure the receiver’s center channel mode is set
to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g., CD-stereo,
videotape, Dolby, Pro Logic). In each case, follow your equipment’s
nstructions to ensure that the subwoofer output is turned on and that
i
the speakers are set to “Small” in each mode.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets
on the back of the receiver.
Initially set the Subwoofer-Level Control
1 to the“MIN” position.
hase Control
P
The Phase Switch 2 determines whether the subwoofer speaker’s
pistonlike action moves in and out with the main speakers (0˚) or
opposite the main speakers (180˚). Proper phase adjustment depends
on several variables such as room size, subwoofer placement and
listener position. Adjust the phase switch to maximize bass output at
the listening position.
Final Positioning
fter correctly connecting the CS480 system and verifying that both the
A
subwoofer and all satellite speakers are playing, it is time to optimize
the system for your particular listening room. Earlier, you placed the
subwoofer in its general location. Finding the exact location for optimum
performance sometimes only involves moving the speakers up to a
few inches in any direction. We urge you, therefore, to experiment
with placement, if possible, until your speakers deliver their full
potential.
Turn on the subwoofer by pressing the Power Switch
6 on the
rear panel.
urn on your entire audio system and start a CD or movie soundtrack
T
at a moderate level.
Auto On/Standby
With the Power Switch 6 in the ON position, the LED on the rear
5 will remain lit in green or red to indicate the ON or STANDBY
panel
mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system. The subwoofer will then power on instantly when a signal
is detected. During periods of normal use, the Power Switch
6
can be left on. You may turn off the Power Switch 6for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
urn the Subwoofer
T
-Level Control
1
up about halfway
. If no sound
emanates from the subwoofer, check the AC-line cord and input
cables. Are the connectors on the cables making proper contact? Is
the AC plug connected to a “live” receptacle? Has the Power Switch
6
been pressed to the ON position? Once you have confirmed that
the subwoofer is active, proceed by playing a CD or DVD. Use a
selection that has ample bass information.
A Few Suggestions
We recommend that you do not operate your speakers or subwoofer with
the bass, treble and loudness controls set to full boost. This will place
undue strain on your electronics and speakers, and could damage them.
The volume control setting on your processor/preamp or receiver is not a
specific indication of the overall loudness level of the speakers. The only
important consideration is the loudness level at which the system can be
played, regardless of where the volume control is set.
Always turn down the volume control setting on your processor/preamp
or receiver when changing sources, or switching inputs to AM or FM
operation. Excessively loud transients (clicks or popping sounds) can
damage the satellite speakers and possibly the subwoofer.
Maintenance and Service
The satellite and subwoofer enclosures may be cleaned using a soft cloth
to remove fingerprints or to wipe off dust.
All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved
in the connections, atmospheric conditions and other factors, but once
per year is the minimum.
In the event that your system ever needs service, contact your
dealer or distributor, or visit www.jbl.com
for a service center near you.
local JBL
Set the overall volume control of the receiver/processor to a comfort
able level. Adjust the Subwoofer
-Level Control 1until you obtain
a pleasing blend of bass. Bass response should not overpower the
room but rather be adjusted so there is a harmonious blend across
the entire musical range. Many users have a tendency to set the
subwoofer volume too loud, adhering to the belief that a subwoofer is
there to produce lots of bass. This is not entirely true. A subwoofer is
there to enhance bass, extending the response of the entire system
so the bass can be felt as well as heard. However, overall balance
must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
-
9
SPECIFICATIONS
CS480
ATELLITES
S
Frequency Response (–6dB): 110Hz – 20kHz
Recommended Amplifier Power Range: 10 – 100 Watts
Sensitivity (2.83V @ 1 meter): 86dB
Nominal Impedance: 8 Ohms
Crossover Frequency: 3.0kHz; 12dB/octave
High-Frequency Driver: 1/2" (13mm) Titanium-laminate dome, magnetically shielded
idrange Driver:
M
Dimensions (H x W x D): 6" x 6-3/8" x 3-7/8" (152mm x 162mm x 98mm)
Weight: 2.0 lb (0.9kg)
CENTER
Frequency Response (–6dB): 100Hz – 20kHz
Recommended Amplifier Power Range: 10 – 100 Watts
Sensitivity (2.83V @ 1 meter): 88dB
Nominal Impedance: 8 Ohms
Crossover Frequency: 3.0kHz; 12dB/octave
High-Frequency Driver: 1/2" (13mm) Titanium-laminate dome, magnetically shielded
Midrange Driver: Dual 3-1/2" (89mm), magnetically shielded
Dimensions (H x W x D): 5-1/4" x 11-3/8" x 3-3/8" (133mm x 289mm x 86mm)
Weight: 3.2 lb (1.5kg)
-1/2" (89mm), magnetically shielded
3
SUBWOOFER
Frequency Response (–6dB): 35Hz – 160Hz
Amplifier: 125W RMS/250W Peak
Driver: 8" (200mm)
Dimensions (H x W x D, including feet): 16-1/4" x 12" x 13-5/8" (413mm x 305mm x 346mm)
Weight: 29 lb (13.2kg)
† The Peak Dynamic Power is measured by recording the highest center-to-peak voltage
measured across the output of a resistive load equal to minimum impedance of the
transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
†
10
All features and specifications are subject to change without notice.
JBL is a trademark of Harman International Industries, Incorporated, registered
in the United States and/or other countries. Pro Sound Comes Home is a trademark
of Harman International Industries, Incorporated.
Dolby and Pro Logic are registered trademarks of Dolby Laboratories.
DTS is a registered trademark of DTS, Inc.
PRO SOUND COMES HOME
®
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA
8500 Balboa Boulevard, Northridge, CA 91329 USA
2, route de Tours, 72500 Château du Loir, France
516.255.4JBL (4525) (USA only) www.jbl.com
© 2007 Harman International Industries, Incorporated. All rights reserved.
Part No.
406-000-05538-E
™
Loading...