JBL CS1204T, CS1204B User Manual

CS SERIES
CS1204B CS1204T
subwoofer enclosures owner’s manual
Designed and Engineered in the USA
2
INSTALLATION WARNINGS AND TIPS
THANK YOU for choosing a JBL CS Series subwoofer enclosure. These products have been designed to deliver great bass performance from a compact, easily installed enclosure. To get the best performance from your enclosure, we strongly recommend that installation be entrusted to a qualified professional. Although these instructions explain how to install your product in a general sense, they do not show specific installation methods that may be required for your particular vehicle. If you do not have the neces­sary tools or experience, do not attempt the installation yourself. Instead, please ask your authorized JBL car audio dealer about professional installation. In order that we may better serve you should you require warranty service, please retain your original sales receipt and serial number.
WARNING: Playing loud music in an automobile can permanently damage your hearing as well as hinder your ability to hear traffic. We recommend listening at low levels while driving. JBL accepts no liability for hearing loss, bodily injury or property damage resulting from use or misuse of this product.
INSTALLATION TIPS
• Always wear protective eyewear when using tools.
• Turn off all audio components and other electrical devices before you start. Disconnect the (–) negative lead from your vehicle’s battery.
• Check clearances on both sides of a planned mounting surface. Be sure that screws or wires will not puncture brake lines, fuel lines or wiring harnesses, and that wire routing will not interfere with the safe operation of the vehicle.
• When making electrical connec­tions, make sure they are secure and properly insulated.
• Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw.
• Do not mount speakers where they will get wet.
• If a fuse must be replaced, be sure to use the same type of fuse and current rating as that of the original.
CHOOSING A MOUNTING LOCATION FOR ENCLOSURE
Choose a mounting location that doesn’t interfere with cargo, the fold-down rear seat or the trunk lid. The best location is usually a corner of the trunk or cargo area. Securely mount enclosure to the mounting surface using the supplied material.
Connect the speaker cable to the enclosure as shown in Figure 1. Please observe the following installation tips:
Use at least 0.5mm2speaker wire for speaker-level input connections.
Figure 1.
3
POWER CONNECTIONS
HEAD UNIT
AMP
BATTERY
Speaker Out
Remote Turn-On
RL
Declaration of Conformity
We,
Harman Consumer Group International 2, route de Tours 72500 Château du Loir France
declare in own responsibility that the products described in this owner’s manual are in compliance with technical standards:
EN 61000-6-3:2001 EN 61000-6-1:2001
Klaus Lebherz
Harman Consumer Group International
Château du Loir, France 1/06
JBL Consumer Products 2 route de Tours, 72500 Château du Loir, France www.jbl.com
© 2006 Harman International Industries, Incorporated. All rights reserved. JBL and Harman International are trademarks of
Harman International Industries, Incorporated, registered in the United States and/or other countries.
Part No. CS1204BTOM 1/06
www.jbl.com
SPECIFICATIONS
CS1204B CS1204T
Type Sealed Enclosure Bass-Reflex
Woofer 300mm (12") 300mm (12")
Power Handling, RMS 250W 250W
Power Handling, Peak 1000W 1000W
Sensitivity (2.83V/1m) 90dB 90dB
Frequency Response 40Hz – 300Hz 35Hz – 200Hz
Impedance 4 Ohms 4 Ohms
Dimensions 408mm x 380mm x 368mm 346mm x 660mm
(L x D x H) (Diam. x Length)
GENERAL CARE
The loudspeaker grilles may be cleaned with a damp cloth. Do not use any cleaners or solvents on the grilles or the speaker cones.
A valid serial number is required for warranty coverage. Features, specifications and appearance are subject to change without notice. This product is designed for mobile applications and is not intended for connection to the mains.
Loading...