subwoofer
enclosures
owner’s manual
INSTALLATION WARNINGS AND TIPS
THANK YOU for
choosing a JBL CS subwoofer
enclosure. These products
have been designed to deliver
great bass performance from
a compact, easily installed
enclosure. To get the best
performance from your
enclosure, we strongly
recommend that installation
be entrusted to a qualified
professional. Although these
instructions explain how to
install your product in a
general sense, they do not
show specific installation
methods that may be required
for your particular vehicle.
If you do not have the
necessary tools or experience, do not attempt the
installation yourself. Instead,
please ask your authorized
JBL car audio dealer about
professional installation. In
order that we may better
serve you should you require
warranty service, please
retain your original sales
receipt and serial number.
INSTALLATION
WARNING
Playing loud music in an
automobile can hinder your
ability to hear traffic and
permanently damage your
hearing. We recommend
listening at low or moderate
levels while driving your car.
JBL accepts no liability for
hearing loss, bodily injury
or property damage resulting
from the use or misuse of
this product.
INSTALLATION TIPS
• Always wear protective
eyewear when using tools.
• Turn off all audio components and other electrical
devices before you start.
Disconnect the (–) negative
lead from your vehicle’s
battery.
• Check clearances on both
sides of a planned mounting
surface. Be sure that screws
or wires will not puncture
brake lines, fuel lines or
wiring harnesses, and that
wire routing will not interfere with the safe operation
of the vehicle.
• When making electrical
connections, make sure they
are secure and properly
insulated.
• Before drilling or cutting
holes, use a utility knife to
remove unwanted fabric or
vinyl, to keep material from
snagging in a drill bit or saw.
• Do not mount speakers
where they will get wet.
• If a fuse must be replaced,
be sure to use the same type
of fuse and current rating as
that of the original.
CHOOSING
A MOUNTING
LOCATION FOR
ENCLOSURE
Choose a mounting location
that doesn’t interfere with
cargo, the fold-down rear
seat or the trunk lid. The best
location is usually a corner
of the trunk or cargo area.
Securely mount enclosure to
the mounting surface using
the supplied material.
Connect speaker cable to enclosure as shown in Figure 1.
Please observe the following
installation tips:
Use at least 0.5mm
2
speaker
wire for speaker-level input
connections.
Figure 1.
POWER CONNECTIONS
HEAD UNIT
AMP
BATTERY
Speaker Out
Remote
Turn-On
RL
SPECIFICATIONS
Declaration of Conformity
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
EN 50081-1:1992
EN 50082-1:1997
Emmanuel Millot
Harman Consumer International
Chateau-du-Loir, France 9/03
JBL Consumer Products
2, route de Tours, 72500 Chateau-du-Loir, France
www.jbl.com
© 2003 Harman International Industries, Incorporated
JBL is a registered trademark of
Harman International Industries, Incorporated.
Part No. CSENCOM8/03
CS1000B CS1200B CS1200T
250mm Subwoofer 300mm Subwoofer 300mm Subwoofer
Type: Sealed Sealed Bass Reflex
RMS Power: 100W 125W 125W
Max Power: 400W 500W 500W
Sensitivity (2.83V, 1m): 94dB 94dB 94dB
Frequency Response: 38Hz – 500Hz 38Hz – 500Hz 38Hz – 500Hz
Impedance: 4 ohms 4 ohms 4 ohms
Dimensions (L x W x H): 360mm x 385mm x 320mm 410mm x 385mm x 360mm Dia: 335mm x 660mm
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
Loading...