Page 1
®
JBL® CONTROL® SERIES
JBL CONTROL NOW
™
JBL CONTROL NOW™ AW
OWNER’S GUIDE
Page 2
TABLE OF CONTENTS
UNPACKING THE SPEAKERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
WALL SURFACE-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
WALL CORNER-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . .6
WALL/CEILING CORNER-MOUNTING . . . . . . . . . . . . . . . . . .8
HALF-ROUND WALL-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . 10
3/4-ROUND WALL-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . .14
STAND-MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
FOUR-SPEAKER-ARRAY INSTALLATION . . . . . . . . . . . . . . . . . . .18
UNPACKING THE BRACKET AND CABLE KIT . . . . . . . . . . . 18
MAINTENANCE AND SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . .27
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
JBL CONTROL NOW
For more than 60 years, we have been providing JBL® audio equipment for top
concert halls, recording studios and movie theaters around the world, becoming
the hands-down choice of leading recording artists and sound engineers. With
JBL Control NOW™ loudspeakers, innovative technologies such as titaniumlaminate dome tweeters, PolyPlas™ transducer reinforcement and a patented,
controlled-directivity Bi-Radial® horn are available to you.
JBL Control NOW speakers are unique in their ability to deliver excellent
performance over an extremely wide listening area. Therefore, the conventional
placement guidelines outlined below can often be relaxed somewhat to offer
you the fl exibility of placing the speakers where they best integrate into your
living environment, without sacrifi cing performance.
™
LOUDSPEAKERS
UNPACKING THE SPEAKERS
If you suspect damage from transit, report it immediately to your dealer.
Keep the shipping carton and packing materials for future use.
Included:
JBL Control NOW Speaker
(2) #10-32 x 2"
(M5 51 mm)
Screws
(1) "1/4-20 x 1"
(M6 25 mm)
Screw
Stand-Mount
Bracket
(2) #8-32 x 1/2"
(M4 13 mm)
Screws
(2) #10-32 x 1/2"
(M5 13 mm)
Screws
Multiunit Wiring Adapter
Corner/Wall-Mount-Bracket Cap
Corner/Wall-Mount Bracket
(2) Bracket Covers
2
Page 3
PLACEMENT
JBL Control NOW speakers are perhaps the most fl exible and versatile loudspeakers ever developed. There are numerous mounting options. The JBL
Control NOW speaker can be wall-mounted or corner-mounted, sit on a shelf or
be used with fl oor stands. Two, three or four speakers can be joined together
to create loudspeaker solutions for virtually any application.
• Use single units as shelf, stand- or wall-mounted speakers in traditional
stereo or home theater applications.
• Join two speakers together to form a visually striking array in single-channel
applications or as a single-point stereo or surround speaker such as rear
surround left and rear surround right.
• Connect three speakers around an outer corner and send full-range sound
throughout two adjacent rooms.
• Suspend four JBL Control NOW speakers from the ceiling, using standard
ceiling-fan hardware and the optional pole-mount bracket (not included).
Confi gure each four-speaker array for use as a single-channel or
single-point stereo.
This owner’s guide will cover the installation and wiring procedures for each
mounting option. Simply decide how you will mount and use the speakers, and
then follow the instructions for your specifi c application.
Please note that while the JBL Control NOW AW speaker is an all-weather
outdoor loudspeaker, it is not waterproof. The speaker should not be
submerged or directly exposed to water, ice, snow or sustained moisture.
JBL Control NOW speakers are designed for indoor use only.
HOME THEATER
For front-channel use, place one speaker on the left and another on the right,
along either side of the television monitor. Since the speakers are magnetically
shielded, you can place them near a CRT TV without worrying about the fi eld
distorting the TV picture.
For surround-channel use, place speakers in corners, on the wall, on bookshelves
or on stands alongside the listening position. Final placement depends on room
acoustics, availability of space and your listening preference.
In 6- or 7-channel confi gurations, place the rear channel(s) behind the listening
position, as shown in Figure 2.
NOTE: A JBL powered subwoofer will add impact and realism to both
music and fi lm soundtracks. Contact your JBL dealer for recommendations
on subwoofer models for your application.
Left
Front
Channel
Center
Channel
Right
Front
Channel
JBL
Subwoofer
(optional)
English
STEREO
Before deciding where to place your speakers, survey your room and think about
placement. Keep the following points in mind, and use Figure 1 as a guide:
• For best results, place the speakers 6"– 8" (1.5m–2.5m) apart.
• Position each speaker so that the tweeter is directed toward the
listening area.
• Generally, bass output will increase as the speaker is moved closer to
a wall or corner.
• Refer to the “Home Theater” section at right if you also plan to use the
speakers for home theater reproduction.
Left
Channel
Right
Channel
Couch
Left
Surround
Channel
Left Rear
Channel
Center Rear
Channel
Right Rear
Channel
Right
Surround
Channel
Figure 2. This overhead view shows a typical home theater plan. Left/right
rear channels are for a 7-channel system. The center rear channel is for
a 6-channel system.
Listening Position
Figure 1. Experiment with speaker placement to obtain the best bass level
and stereo imaging in your room.
3
Page 4
WALL SURFACE-MOUNTING
When deciding upon a location for the JBL Control NOW speaker, take care
NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2"
(21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements
will not allow the room needed to position and slide the JBL Control NOW
speaker into the mounting bracket.
CAUTION
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the
speakers. The JBL Control NOW speaker was designed to be easily installed.
However, if you are unable to clearly and fully understand and follow the
instructions in this manual, or if you are unsure of your ability to properly install
these loudspeakers, please contact your dealer or a qualifi ed installer. Please
do not use any power tools during installation. Power tools can exert excessive
and unnecessary torque which, in turn, can damage fasteners or other parts
and accessories, reducing their strength and causing possible failure of the
fastener or part. A failed or damaged fastener or part may not be able to
perform as designed, and may lead to an unsafe installation.
1. Run the wiring to the location desired for mounting the JBL Control NOW speaker.
2. Using a level, secure the mounting bracket to the wall. Be sure to use an
appropriate anchor.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
Standard
Connection
Corner/Wall-MountBracket Assembly
NOTE: There are two
cable access holes
provided in the Wall-
Mount Assembly.
3"(7,6 cm) Minimum
distance from ceiling
to top of bracket
(horizontal mount)
3. Connect the wires to the JBL Control NOW speaker.
8-1/2"(21,5 cm) Minimum
distance from ceiling
to top of bracket
(vertical mount)
Appropriate
anchors
RED = +
BLACK = —
Wiring diagram shows
polarity connections for
one channel of a stereo or
home theater system.
4
Page 5
4 . The mounting bracket is designed to trap the fl ange of the JBL Control NOW
speaker by securing the mounting-bracket cap with two screws through
the bottom of the mounting bracket. Rest the JBL Control NOW speaker’s
rear fl ange in the mounting bracket, as shown. This will support the weight
of the speaker. Slide the mounting-bracket cap over the assembly. Secure
the mounting-bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws
(provided) in the bottom of the mounting bracket and tightening.
Mounting-Bracket Cap
Mounting Bracket
(side view)
#10-32 x 2" (M5 51 mm) Screws (2)
(side view)
English
An alternate
vertical orientation
is shown here
Vertical
orientation
Bracket Cover
Mounting-Bracket Cap
Mounting Bracket
#10-32 x 2"
(M5 51 mm)
Screws (2)
Mounting Bracket
shown as looking through
the speaker.
5. To orient the JBL logo into the correct position, pull the JBL logo slightly
outward from the speaker grille and rotate. The JBL logo is held in place by
a spring. Peel the adhesive cover off the mounting-bracket cover and attach
to the top and bottom of the mounting assembly.
Mounting-Bracket
Cover
Vertical
orientation
Bracket Cover
Regardless of whether you choose a vertical or horizontal orientation,
when mounting the JBL Control NOW speaker to a single wall surface, you
should always install the wall-mounting bracket in a vertical orientation.
Mounting-Bracket
Cover
5
Page 6
WALL CORNER-MOUNTING
CAUTION
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the
speakers. The JBL Control NOW speaker was designed to be easily installed.
However, if you are unable to clearly and fully understand and follow the
instructions in this manual, or if you are unsure of your ability to properly install
these loudspeakers, please contact your dealer or a qualifi ed installer. Please
do not use any power tools during installation. Power tools can exert excessive
and unnecessary torque which, in turn, can damage fasteners or other parts
and accessories, reducing their strength and causing possible failure of the
fastener or part. A failed or damaged fastener or part may not be able to
perform as designed, and may lead to an unsafe installation.
When deciding upon a location for the JBL Control NOW speaker, take care
NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2"
(21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements
will not allow the room needed to position and slide the JBL Control NOW
speaker into the mounting bracket.
Corner/Wall-MountBracket Assembly
1. Run the wiring to the location desired
for mounting the JBL Control NOW
speaker.
NOTE: There are two
cable access holes
provided in the Wall-
Mount Assembly.
3. Connect the wires to the JBL Control NOW speaker.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
Standard
Connection
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.
3" (7,6 cm) Minimum
distance
from ceiling
(horizontal mount)
8-1/2" (21,5 cm) Minimum
distance from ceiling
(vertical mount)
Appropriate
anchors
RED = +
BLACK = —
Wiring diagram shows
polarity connections for
one channel of a stereo or
home theater system.
6
Page 7
4. The mounting bracket is designed to trap the fl ange of the JBL Control NOW
speaker by securing the mounting-bracket cap with two screws through the
bottom of the mounting bracket. Rest the JBL Control NOW speaker’s rear
fl ange in the mounting bracket, as shown. This will support the weight of the
speaker. Now slide the mounting-bracket cap over the assembly. Secure the
mounting-bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening.
Mounting-Bracket Cap
Mounting Bracket
(side view)
#10-32 x 2" (M5 51 mm) Screws (2)
(side view)
5. To orient the JBL logo into the correct position, pull the JBL logo slightly
outward from the speaker grille and rotate. The JBL logo is held in place by
a spring. Peel the adhesive cover off the mounting-bracket cover and attach
to bottom of mounting assembly.
Mounting-Bracket Cover
English
Mounting Bracket
shown as looking through
the speaker.
Ceiling line
Mounting Bracket
To p C ap
#10-32 x 2"
(M5 51 mm)
7
Page 8
WALL/CEILING CORNER-MOUNTING
(VERTICAL MOUNTING ONLY)
CAUTION
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the
speakers. The JBL Control NOW speaker was designed to be easily installed.
However, if you are unable to clearly and fully understand and follow the
instructions in this manual, or if you are unsure of your ability to properly install
these loudspeakers, please contact your dealer or a qualifi ed installer. Please
do not use any power tools during installation. Power tools can exert excessive
and unnecessary torque which, in turn, can damage fasteners or other parts and
accessories, reducing their strength and causing possible failure of the
fastener or part. A failed or damaged fastener or part may not be able to
perform as designed, and may lead to an unsafe installation.
When deciding upon a location for the JBL Control NOW speaker, take care
NOT to install the mounting bracket closer than 3" (7,6 cm) to a side wall. Any
closer than 3" (7,6 cm) will not allow the room needed to position and slide the
JBL Control NOW speaker into the mounting bracket.
3" (7,6 cm) Minimum
distance from wall
3. Connect the wires to the JBL Control NOW speaker.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect each + terminal on the back of the
amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when
making connections. Doing so will cause poor imaging and diminished bass
response.
Standard
Connection
1. Run the wiring to the location desired for mounting the JBL Control NOW speaker.
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.
Appropriate
anchors
RED = +
BLACK = —
Wiring diagram shows
polarity connections for
one channel of a stereo or
home theater system.
8
Page 9
4. The mounting bracket is designed to trap the fl ange of the JBL Control NOW
speaker by securing the mounting-bracket cap with two screws through the
side of the mounting bracket. Rest the JBL Control NOW speaker’s fl ange in
the mounting bracket, as shown. This will support the weight of the speaker.
Now slide the mounting-bracket cap over the assembly. Secure the mountingbracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the
side of the mounting bracket and tightening.
5. To orient the JBL logo into the correct position, pull the JBL logo slightly
outward from the speaker grille and rotate. The JBL logo is held in place by
a spring. Peel the adhesive cover off the mounting-bracket cover and attach
to sides of the mounting assembly.
Bracket
Cover
English
#10-32 x
(M5 51 mm)
#10-32 x 2"
(M5 51 mm)
Screws (2)
This illustration shows
speaker viewed from
beneath.
Screws (2)
2"
Mounting
Bracket
Mounting
Bracket
Top Cap
Mounting Bracket
shown as looking through
the speaker.
Top Cap
9
Page 10
HALF-ROUND WALL-MOUNTING
(HORIZONTAL OR VERTICAL)
NOTE: Decide whether you will connect the speakers as a single channel
or two separate channels, and follow the appropriate instructions on
the following pages.
CONNECT AS A SINGLE CHANNEL
CAUTION
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the
speakers. The JBL Control NOW speaker was designed to be easily installed.
However, if you are unable to clearly and fully understand and follow the
instructions in this manual, or if you are unsure of your ability to properly install
these loudspeakers, please contact your dealer or a qualifi ed installer. Please
do not use any power tools during installation. Power tools can exert excessive
and unnecessary torque which, in turn, can damage fasteners or other parts
and accessories, reducing their strength and causing possible failure of the
fastener or part. A failed or damaged fastener or part may not be able to
perform as designed, and may lead to an unsafe installation.
1. Secure two corner/wall-mounting
brackets together by using two
#10-32 x 1/2" (M5 13 mm) screws provided, as shown. Attach the mounting
bracket to the wall.
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.
Appropriate
anchors
3. Remove the terminal assemblies from the rear of both speakers. The terminal
assembly is removed by giving it a slight counterclockwise rotation. Use the
transparent plastic strap to pull the assembly out, as shown.
#10-32 x 1/2"
(M5 13 mm)
Screws (2)
When deciding upon a location for the JBL Control NOW speaker, take care
NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2"
(21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements
will not allow the room needed to position and slide the JBL Control NOW
speaker into the mounting bracket.
3" (7,6 cm) Minimum
distance from ceiling
(horizontal mount)
8-1/2" (21,5 cm) Minimum
distance from ceiling
(vertical mount)
4. Connect the small end of the multiunit wiring adapter to one of the speaker
rears, as shown.
10
Page 11
5. The mounting bracket is designed to trap the fl ange of the JBL Control NOW
speaker by securing the mounting-bracket cap with two screws through the
bottom of the mounting bracket. Run the loose end of the multiunit wiring
adapter through the rear cable-management hole in the mounting bracket,
and rest the JBL Control NOW speaker’s rear fl ange in the mounting bracket,
as shown. This will support the weight of the speaker. Now slide the mountingbracket cap over the assembly. Secure the mounting-bracket cap by
inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the
mounting bracket and tightening.
Mounting-Bracket Cap
8. Now connect the wires to the terminal assembly.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
English
Mounting Bracket
(side view)
#10-32 x 2" (M5 51 mm) Screws (2)
(side view)
6. Place the large end of the multiunit wiring adapter into the second speaker
to be installed. Slide the multiunit wiring adapter into the rear of the speaker
at a slight angle and rotate clockwise.
Already connectedto the other speaker.
7. Connect the terminal assembly to the back of the multiunit wiring adapter.
It will snap securely into place.
Standard
Connection
Wiring diagram shows
polarity connections for
one channel of a stereo or
RED = +
BLACK = —
home theater system.
9. To orient the JBL logo into the correct position, pull the JBL logo slightly
outward from the speaker grille and rotate. The JBL logo is held in place by
a spring. Peel the adhesive cover off the mounting-bracket covers and
attach to the top and bottom of the mounting assembly.
Mounting-Bracket
Covers
Already connectedto the other speaker.
Mounting-Bracket
Covers
11
Page 12
CONNECT AS TWO CHANNELS
CAUTION
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the
speakers. The JBL Control NOW speaker was designed to be easily installed.
However, if you are unable to clearly and fully understand and follow the
instructions in this manual, or if you are unsure of your ability to properly install
these loudspeakers, please contact your dealer or a qualifi ed installer. Please
do not use any power tools during installation. Power tools can exert excessive
and unnecessary torque which, in turn, can damage fasteners or other parts
and accessories, reducing their strength and causing possible failure of the
fastener or part. A failed or damaged fastener or part may not be able to
perform as designed, and may lead to an unsafe installation.
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.
Appropriate
anchors
1. Secure two corner/wall-mounting
brackets together by using two
#10-32 x 1/2" (M5 13 mm) screws provided, as shown. Attach the mounting
bracket to the wall.
#10-32 x 1/2"
(M5 13 mm)
Screws (2)
When deciding upon a location for the JBL Control NOW speaker, take care
NOT to install the mounting bracket closer than 3" (7,6 cm) (horizontal) and 8-1/2"
(21,5 cm) (vertical) to the ceiling. Any closer than the minimum measurements
will not allow the room needed to position and slide the JBL Control NOW
speaker into the mounting bracket.
3" (7,6 cm) Minimum
distance from ceiling
(horizontal mount)
8-1/2" (21,5 cm) Minimum
distance from ceiling
(vertical mount)
3. Connect the wires to the terminal assembly of each of the JBL Control NOW
speakers.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
12
Standard
Connection
RED = +
BLACK = —
Wiring diagram shows
polarity connections for
one channel of a stereo or
home theater system.
Page 13
4. The mounting bracket is designed to trap the fl ange of the JBL Control NOW
speaker by securing the mounting bracket cap with two screws through the
bottom of the mounting bracket. This will support the weight of the speaker.
Now slide the mounting-bracket cap over the assembly. Secure the mounting- bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in
the bottom of the mounting bracket and tightening. Repeat the process with the
remaining speaker.
Mounting-Bracket Cap
Mounting Bracket
(side view)
#10-32 x 2" (M5 51 mm) Screws (2)
(side view)
5. Now rest the second JBL Control NOW speaker’s rear fl ange in the mounting
bracket, as shown, and complete the process. Secure the mounting-bracket
cap with two #10-32 x 2" (M5 51 mm) screws through the bottom of the
mounting bracket.
#10-32 x 2"
Screws (2)
English
#10-32 x 2"
(M5 51 mm)
Screws (2)
6. To orient the JBL logo into the correct position, pull the JBL logo slightly
outward from the speaker grille and rotate. The JBL logo is held in place by
a spring. Peel the adhesive cover off the mounting-bracket covers and
attach to the top and bottom of the mounting assembly.
Mounting-Bracket
Covers
Mounting-Bracket
Covers
13
Page 14
3/4-ROUND WALL-MOUNTING
Speaker 1
When deciding upon a location for the JBL Control NOW speaker, take care
NOT to install the mounting bracket closer than 3" (7,6 cm) to the ceiling. Any
closer than 3" (7,6 cm) will not allow the room needed to position and slide the
JBL Control NOW speaker into the mounting bracket.
ceiling
3" (7,5 cm) Minimum
distance from ceiling
to top of bracket
(horizontal mounting)
Speaker 2
Speaker 3
CAUTION
The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the
speakers. The JBL Control NOW speaker was designed to be easily installed.
However, if you are unable to clearly and fully understand and follow the
instructions in this manual, or if you are unsure of your ability to properly install
these loudspeakers, please contact your dealer or a qualifi ed installer. Please
do not use any power tools during installation. Power tools can exert excessive
and unnecessary torque which, in turn, can damage fasteners or other parts
and accessories, reducing their strength and causing possible failure of the
fastener or part. A failed or damaged fastener or part may not be able to
perform as designed, and may lead to an unsafe installation.
1. Secure three corner/wall-mounting brackets together by using four
#10-32 x 1/2" (M5 13 mm) screws provided as shown.
#10-32 x 1/2" (M5 13 mm)
Screws (2)
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors.
Appropriate
anchors
3. Remove the terminal assemblies from the rear of all speakers. The terminal
assembly is removed by giving it a slight counterclockwise rotation. Use the
transparent plastic strap to pull the assembly out, as shown.
#10-32 x 1/2" (M5 13 mm)
Screws (2)
14
Page 15
4. Connect the small end of the multiunit wiring adapter to the rear of
speaker 1, as shown.
6. Place the large end of the multiunit wiring adapter that is already connected
to speaker 1 into speaker 2 by sliding the multiunit wiring adapter into the
rear of the speaker at a slight angle and rotate clockwise.
This end is connected tothe first speaker now resting
in the Corner/Wall-Mount Bracket.
English
5. The mounting bracket is designed to trap the fl ange of the JBL Control NOW
speaker by securing the mounting-bracket cap with two screws through the
bottom of the mounting bracket. Run the loose end of the multiunit wiring
adapter through the rear cable-management hole in the mounting bracket
and rest the JBL Control NOW speaker’s rear fl ange in the mounting bracket,
as shown. This will support the weight of the speaker. Slide the mountingbracket cap over the assembly. Secure the mounting-bracket cap by inserting
two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting
bracket and tightening.
#10-32 x 2"
(M5 51 mm)
Screws
(2)
7. Connect the small end of an additional multiunit wiring adapter to the speaker
rear as shown.
This end is connected tothe first speaker now resting
in the Corner/Wall-Mount Bracket.
8. Rest the second JBL Control NOW speaker’s rear fl ange in the mounting
bracket, as shown, and complete the process. Secure the mounting bracket
cap with two #10-32 x 2" (M5 51 mm) screws through the bottom of the
mounting bracket.
Mounting-Bracket Cap
Mounting Bracket
(side view)
#10-32 x 2" (M5 51 mm) Screws (2)
(side view)
#10-32 x 2"
Screws (2)
15
15
Page 16
9. Place the large end of the multiunit wiring adapter that is already installed in
speaker 2 into speaker 3 by sliding a multiunit wiring adapter into the
rear of it at a slight angle and rotate clockwise.
This end is connected to the second speaker currently
resting in the Corner/Wall-Mount Bracket assembly.
10. Connect the terminal assembly to the back of the second multiunit wiring
adapter. It will snap securely into place. The other end of the multiunit
wiring adapter will already be connected to the other speaker already
mounted in the corner/wall-mount bracket assembly.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
Standard
Connection
Wiring diagram shows
polarity connections for
one channel of a stereo or
RED = +
BLACK = —
home theater system.
12. Rest the third JBL Control NOW speaker’s rear fl ange in the mounting
bracket as shown and complete the process. Secure the mounting-bracket
cap with 2 screws through the bottom of the mounting bracket.
This end is connected to the second speaker currently
resting in the Corner/Wall-Mount-Bracket Assembly.
11. Connect the wires to the terminal assembly and place the speaker on
the remaining bracket.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
13. To orient the JBL logo into the correct position, pull the JBL logo slightly
outward from the speaker grille and rotate. The JBL logo is held in place
by a spring. Peel the adhesive cover off the mounting-bracket covers and
attach to top and bottom of mounting-bracket assembly.
Speaker 1
Speaker 2
Mounting-Bracket
Covers
Mounting-Bracket
Covers
Speaker 3
16
Page 17
STAND-MOUNTING
IMPORTANT SAFETY NOTE:
CAUTION
The supplied fl oor stand adapters facilitate installation with a variety of generalpurpose fl oor stands available from many manufacturers. Since different stands
will have different weight capacities and stability characteristics, it is the
customer’s responsibility to check with the stand manufacturer or dealer to
ascertain whether that specifi c stand is capable of handling the weight and
proportions of these loudspeakers in a safe and stable manner. JBL, Inc.,
disclaims any liability for the selection of suitable fl oor stands and/or correct
compatibility between the selected stand and the supplied stand adapter.
1. Attach the stand-mounting bracket
to the stand with the #1/4-20 x 1"
Note trough in Stand-Mount
Bracket for
cable management.
#1/4-20 x 1"
(M6 25 mm)
(M4 13 mm)
Screw Provided
Stand
Stand-Mount Bracket
(M6 25 mm) screw as shown.
2. Run the wiring as shown.
3. Place the JBL Control NOW speaker
on the stand-mount bracket and
stand, as shown.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
Standard
Connection
RED = +
BLACK = —
Wiring diagram shows
polarity connections for
one channel of a stereo or home theater system.
English
4. Use two #8-32 x 1/2" (M4 13 mm)
screws provided to secure the JBL
Control NOW speaker to the stand.
5. Attach wires.
#8-32 x 1/2" Screws
An alternate orientation
shown here.
17
Page 18
FOUR-SPEAKER ARRAY USING THE OPTIONAL POLE-MOUNT BRACKET
(PMB)
CAUTION
The JBL Control NOW PMB Pole-Mount Bracket facilitates installation of the
JBL Control NOW and JBL Control NOW AW loudspeakers with a variety of
general-purpose ceiling-fan-pole assemblies available from many manufacturers.
Since different fan-pole assemblies will have different weight capacities, pole
diameters and mounting systems, it is the customer’s responsibility to check
with the fan-pole-assembly manufacturer or dealer to determine whether that
specifi c pole-mount assembly is capable of correctly and securely attaching to
the PMB and handling the weight and proportions of these loudspeakers in
a safe and stable manner. JBL, Inc., disclaims any liability for the selection of
fan-pole assemblies and/or correct compatibility between the selected fan-pole
assembly and the JBL Control NOW PMB.
UNPACKING THE BRACKET AND CABLE KIT
Carefully unpack the bracket and cable assembly. If you suspect damage
from transit, report it immediately to your dealer and/or delivery service.
Keep the shipping carton and packing materials for future use. Open the
package and verify the following contents:
SPEAKER IDENTIFICATION CHART
Included:
Pole Bushing
(used for
Pole-Mount-Bracket Cap
smaller-diameter
drop tubes)
Cotter Pin
ATTACHING POLE TO POLE-MOUNT BRACKET
(FOR LARGER-DIAMETER DROP TUBES)
1. Run the appropriate wiring down through the drop tube. Slide the drop tube
through the pole-mount-bracket cap.
Pole-Mount Bracket
Pole-Mount-Bracket Cover
Clevis Pin
Drop Tube
(4) #10-32 x 2" (M5 51 mm) Screws
Cable Assembly
Pole-Mount-Bracket Cap
18
Page 19
2A. Slide the pole-mount bracket up onto the drop tube, aligning the pinholes
on the bracket with those on the drop tube.
3. Slide the clevis pin through the aligned holes in the pole-mount bracket and
drop tube. Secure the clevis pin by inserting the cotter pin through the hole
in the clevis pin.
English
Pole-MountBracket Cap
Drop Tube
Pinholes
Pole-Mount Bracket
(FOR SMALLER-DIAMETER DROP TUBES)
2B. When using a smaller drop tube, use the pole bushing when running the
wiring down through pole-mount-bracket cap. This will help to eliminate
pole wobble.
Pole-Mount-BracketCap
Cotter Pin
Pole-Mount Bracket
Drop Tube
Clevis Pin
4. The pole-mount bracket can now hold the weight of the speakers.
Pole-Mount-Bracket Cap
Drop Tube
Pole Bushing
Pole-Mount Bracket
Clevis Pin
19
Page 20
SPEAKER WIRING
r
There are four possible ways of wiring the JBL Control NOW speakers when using the pole-mount kit.
1. Use the cable assembly provided to wire the units for a single channel.
Cable Assembly
AB
D
Single-channel-wiring diagram.
2. Use the multiunit wiring adapters to wire the units for two channels.
NOTE: There are two options for 2-channel wiring:
2A. Even sound distribution – Use this connection for even sound distribution
through both channels. This may be more
appropriate for larger rooms.
C
2B. Stereo sound distribution – Use this connection for a smaller
home theater/stereo environment.
Channel 2Channel 1
A
Channel
1
Multiunit
Wiring Adapter
Channel
1
D
2-Channel-wiring diagram for stereo sound distribution.
3. Use four sets of cables to wire the units for four channels.
Terminal
Assemblies
B
Channel
2
Multiunit
Wiring Adapter
Channel
2
C
A
Channel
B
Channel
1
Multiunit
Wiring Adapter
Channel
Channel
2
D
2-Channel-wiring diagram for even sound distribution.
C
Channel2Channel 1
2
Multiunit
Wiring Adapte
1
Channel 2 Channel 3
AB
Channel
1
Channel
2
D
4-Channel-wiring diagram.
Channel 4Channel 1
Channel
4
Channel
3
C
20
Page 21
SINGLE-CHANNEL WIRING
1. Use the cable assembly provided. Run the cable assembly down the drop
tube; run the four sets of paired wires out through the wire access holes,
as shown.
NOTE: This procedure is applicable for both large- and small-diameter
drop tubes. A large-diameter drop tube is shown here.
Pole-Mount-Bracket Cap
Drop Tube
Pole-Mount Bracket
Wire Access Holes
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
Standard
Connection
Wiring diagram shows
polarity connections for
one channel of a stereo or
RED = +
BLACK = —
home theater system.
English
Single-channel wiring.
NOTE: This procedure is applicable for both large- and small-diameter
drop tubes. A large-diameter drop tube is shown here.
2. Connect the wires to the terminal assembly of each speaker as shown.
Place the speaker on the mounting bracket, as shown in step 6 of the mounting- bracket-installation procedures. Return to the installation procedures and
continue.
21
Page 22
2-CHANNEL WIRING FOR EVEN
SOUND DISTRIBUTION
1. Use the even sound distribution connection for even sound distribution through
both channels. Run the sets of paired wires out two wire access holes
through the pole-mount bracket, as shown.
NOTE: This procedure is applicable for both large- and small-diameter
drop tubes. A large-diameter drop tube is shown here.
Pole-Mount-
Bracket Cap
3. Connect the small end of the multiunit wiring adapter to the rear of speakers
A and B, as shown.
4. Place speakers A and B with connectors attached on the pole-mount bracket,
as shown. Run the wiring for the multiunit wiring adapter through the wire
access holes, as shown.
Drop Tube
Pole-Mount
Bracket
Wire Access Holes
2-Channel-wiring for even sound distribution.
2. Remove the terminal assemblies from the rear of all speakers. The terminal
assembly is removed by rotating it slightly counterclockwise, as shown.
A
Pole-Mount-Bracket Cap
Multiunit Wiring Adapter
to connectto speaker
Connector
Pole-Mount
D
Bracket
Drop Tube
Connector
Wire Access
Holes
B
Multiunit Wiring Adapter
to connectto speaker
C
5. Slide the large end of the multiunit wiring adapter that is already attached
to speaker A into the rear of speaker C at a slight angle and rotate clockwise,
as shown.
This end is connected to speaker
6. Connect the terminal assembly to the back of the multiunit wiring adapter,
as shown. It will snap securely into place.
A.
Use the transparent plastic strap to pull the terminal assembly out, as shown.
22
This end is connected to speaker A.
Page 23
7. Connect the wires to the terminal assembly and place the speaker on the
pole-mount bracket. Repeat this process with speaker D. Return to the
installation procedures and continue.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
English
Standard
Connection
RED = +
BLACK = —
Wiring diagram shows
polarity connections for
one channel of a stereo or
home theater system.
23
Page 24
2-CHANNEL STEREO WIRING
1. Use the stereo sound-distribution connection for a smaller home theater/stereo
environment. Run the sets of paired wires out two opposite wire access holes
through the pole-mount bracket, as shown.
NOTE: This procedure is applicable for both large- and small-diameter
drop tubes. A large-diameter drop tube is shown here.
Pole-Mount-Bracket
Cap
Drop Tube
Pole-Mount
Bracket
3. Connect the small end of the multiunit wiring adapter to the rear of speakers
D and B, as shown.
4. Place speakers D and B with connectors attached on the pole-mount bracket,
as shown. Run the wiring for the multiunit wiring adapter through the wire
access holes, as shown.
Drop Tube
A
Pole-Mount-Bracket Cap
Connector
B
D
Multiunit Wiring Adapter
to connectto speaker
Wire Access Holes
2-Channel-wiring for stereo sound distribution.
2. Remove the terminal assemblies from the rear of all four speakers. The terminal
assembly is removed by rotating it slightly counterclockwise, as shown.
Use the transparent plastic strap to pull the terminal assembly out, as shown.
Pole-MountBracket
Connector
Wire Access
Holes
Multiunit Wiring Adapter
to connectto speaker
C
5. Slide the large end of the multiunit wiring adapter that is already attached
to speaker B into the rear of speaker C at a slight angle and rotate clockwise,
as shown.
This end is connected to speaker
B.
6. Connect the terminal assembly to the back of the multiunit wiring adapter. It
will snap securely into place.
24
This end is connected to speaker B.
Page 25
7. Connect the wires to the terminal assembly and place the speaker on
the pole-mount bracket. Repeat this process with speaker A. Return to
the installation procedures and continue.
IMPORTANT: Make sure all equipment is turned off before making
any connections. For speaker connections, use a high-quality speaker wire
with polarity coding. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire and
connection options.
1. Strip 1/4" (6 mm) of wire
2. Press and push connector
3. Insert bare end;
release push connector
RED = +
BLACK = —
The speakers have coded terminals that
accept a variety of wire connectors. The most
common connection is shown in the diagram
to the left. To ensure proper polarity, connect
each + terminal on the back of the amplifi er
or receiver to the respective + (red) terminal
on each speaker, as shown. Connect the
– (black) terminals in a similar way. See
the owner’s guides that were included with
your amplifi er, receiver and television to
confi rm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to – or – to +) when making
connections. Doing so will cause poor imaging and diminished bass response.
4-CHANNEL WIRING
1. Run the four sets of paired wires out the wire access holes, as shown.
NOTE: This procedure is applicable for both large- and small-diameter
drop tubes. A large-diameter drop tube is shown here.
Pole-Mount-Bracket Cap
Drop Tube
Pole-Mount Bracket
Wire Access Holes
4-Channel wiring.
2. Connect the wires to the terminal assembly of each speaker, as shown,
and place the speaker on the mounting bracket, as shown in step 6 of the
mounting-bracket-installation procedures. Return to the installation
procedures and continue.
English
Standard
Connection
RED = +
BLACK = —
Wiring diagram shows
polarity connections for
one channel of a stereo or
home theater system.
25
Page 26
SPEAKER MOUNTING
After carefully placing all four speakers in the mounting bracket, lightly jostle
the speakers into place so that the pole-mount-bracket cap will slide down into
place. Tighten the pole-mount-bracket assembly with the four #10-32 x 2" (M5 51
mm) screws provided.
Drop Tube
Pole-Mount-Bracket Cap
Pole-MountBracket
Place the pole-mount-bracket cover over the bottom visible mounting bracket
by snapping it into place.
#10-32 x 2"(M5 51 mm)
Screws (4)
Only two speakers shown here
for clarity.
Drop Tube
26
Pole-MountBracket Cap
Page 27
MAINTENANCE AND SERVICE
The enclosure may be cleaned using a soft cloth to remove fi ngerprints or to
wipe off dust.
All wiring connections should be inspected and cleaned or remade periodically.
The frequency of maintenance depends on the metals involved in the connections,
atmospheric conditions and other factors, but once per year is the minimum.
If a problem occurs, make sure that all connections are properly made and
clean. If a problem exists in one loudspeaker, reverse the connection wires to
the left and right system. If the problem remains in the same speaker, then the
fault is with the loudspeaker. If the problem appears in the opposite speaker,
the cause is in another component or cable. In the event that your speaker
ever needs service, contact your local JBL dealer or distributor or visit www.
jbl.com for a service center near you.
NOTE: The serial number is located on the rear of the speaker housing.
To view it, remove the four screws on the rear assembly as shown.
The product identification
label is located behind
the rear housing bracket.
English
The serial number is
located on the back top
area of the speaker housing
between the two top rear
bracket-bolt holes.
27
Page 28
SPECIFICATIONS
JBL CONTROL NOW
JBL CONTROL NOW™ AW
Frequency Response (–6dB) 80Hz – 30kHz
Max. Recommended Amplifi er Power* 150W
Power Handling (Continuous/Peak) 50W/300W
Sensitivity (2.83V/1m) 90dB
Nominal Impedance 8 Ohms
Crossover Frequencies 2000Hz – 18dB/octave; woofer 36dB/octave tweeter;
Low-Frequency Transducers Dual 4" (100mm) PolyPlas,™ shielded
High-Frequency Transducer 3/4" (19mm) Titanium-laminate dome,
shielded; waveguide
Weight per Speaker 6.6 lb (3kg)
14-5/16" (364mm)
™
10-3/8" (262mm)
9-7/8" (251mm)
5" (127mm)
The maximum recommended amplifi er power rating will ensure proper system headroom to allow for
*
occasional peaks. We do not recommend sustained operation at these maximum power levels.
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the products described
in this owner’s manual are in compliance with technical
standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
28
Laurent Rault
Harman Consumer Group, Inc.
Château du Loir, France
4/08
Page 29
English
29
Page 30
Features, specifi cations and appearance are subject to change without notice.
JBL and Bi-Radial are trademarks of Harman International Industries, Incorporated, registered
in the United States and/or other countries. JBL Control NOW, PolyPlas and Pro Sound Comes Home
are trademarks of Harman International Industries, Incorporated.
PRO SOUND COMES HOME
®
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA
8500 Balboa Boulevard, Northridge, CA 91329 USA
2, route de Tours, 72500 Château du Loir, France
www.jbl.com
© 2008 Harman International Industries, Incorporated. All rights reserved.
Part No.
406-000-05609-E
™
Loading...