Page 1
Control
®
28
High Output
Indoor/Outdoor
Background/Foreground Speaker
Key Features:
䉴
Components: 8” Polypropylene
coated woofer, 1” Titanium coated
horn loaded tweeter.
䉴
Built-in InvisiBall®patented
mounting hardware
䉴
Weather resistant enclosure and
transducers
䉴
Readily paintable
䉴
90° x 90° high frequency horn
䉴
Overload Protection Circuitry
䉴
Sensitivity: 92 dB SPL, 1W, 1m
The Control®28 offers a rich sonic
character making it a perfect choice
for restaurants, health clubs, under
balcony, outdoor theme & water
parks, or other applications where
foreground/background music and
paging are required.
The patented InvisiBall mounting
hardware is included in each system
and makes short work of permanent
installation. The InvisiBall mounting
method adds the benefit of vertical
rotation of up to 37° off-axis and
horizontal rotation of up to 44° offaxis. Because InvisiBall adjustments
are made through a hidden access
behind the logo badge, the grill
never needs to be removed and there
exists a high degree of theft
deterrence as well.
The Control®28 readily accepts a
variety of paints and finishes to
match any decor.
Weather resistance is maximized by
coating the woofer cone in
polypropylene and terminating its
circumference in JBL’s
WeatherEdge™, a seamless,
rubberized extension of the woofer
surround that provides added
protection to critical transducer
elements. The polycarbonate tweeter
diaphragm is reinforced with a thin
film of titanium for added rigidity and
endurance against sun, salt and
moisture. Zinc plated grilles resist
rusting in the harshest conditions.
Available in black (Control 28) and
white (Control 28-WH).
Specifications:
Frequency Range (-10 dB)1: 60 Hz to 16 kHz
Continuous Program:
Power Capacity2: 175 Watts
Sensitivity3: 92 dB SPL, 1W, 1m
Directivity Factor (Q): 7.5
Directivity Index (DI): 8.8
Nominal Impedance: 8 ohms
Crossover Frequency: 2.8 kHz
LF Driver: 200 mm (8 in) Polypropylene cone w/WeatherEdge
HF Driver: 25 mm (1 in) Titanium coated polycarbonate
Enclosure Material: HIPS (High Impact Polystyrene)
Overload Protection: Full-Range power limiting to protect network and transducers
Termination: Spring terminals, accepts banana plug
Environmental: Conforms to Mil Spec 810 for humidity, salt spray,
temperature & UV. IEC 529 IP-34 splashproof rating.
Dimensions (H x W x D): 380 x 280 x 220 mm (15.0 x 11.0 x 8.6 in)
Net Weight (ea): 5.5 kg (12 lb)
Shipping Weight (pr): 11 kg (25 lb)
Included Accessories: Invisiball Assembly
6 mm x 180 mm hex key
Optional Accessories:
MTC-28V: For vertical columnar orientation of up to 3 loudspeakers
MTC-28H: For horizontal splaying of two speakers. Three brackets array
up to six loudspeakers in a 360° array.
MTC-28/25CM: Ceiling-mount adapter.
MTC-23SSG: Stainless Steel Grille for harsh environments. Available in
silver, black (-BK) or white (-WH)
MTC-23WMG: WeatherMax™ Stainless Steel Grille protects against driving
precipitation. Available in black or white (-WH)
MTC-PC2: Input panel cover protects input terminals in outdoor
environments
1
Half-space (on-wall).
2
Continuous program power is a conservative expression of the system’s ability to handle normal speech and music
program material and is defined as 3 dB above the Continuous Pink Noise Rating (IEC-shaped pink noise with a 6 dB
crest factor, for 100 hours continuously).
3
Half-space (on-wall), ave 100 Hz to 10 kHz.
JBL continually engages in research related to product improvement. Changes introduced into existing products without
notice are an expression of that philosophy.
Professional Series
Page 2
䉴 Control®28 High Output Indoor/Outdoor Background/Foreground Speaker
Frequency Response in half-space
(2, solid line) and full-space (4,
dotted line), and Input Impedance
Beamwidth
Directivity Index, Q
Horizontal Off Axis Frequency Response
Vertical Off Axis Frequency Response (up)
Vertical Off Axis Frequency Response (down)
Page 3
Horizontal 1/3 Octave Polars
Architectural Specifications:
The loudspeaker shall consist of a 200 mm (8 in) low frequency
transducer, 25 mm (1 in) high frequency transducer, and frequency
dividing network installed in a ported enclosure. The low frequency
voice coil shall be 32 mm (1-1/4 in) in diameter.
Performance specifications of a typical production unit shall be as
follows: Measured sensitivity (SPL at 1 m [3.3 ft] with 2.83V input,
averaged from 500 Hz to 1.5 kHz) shall be at least 92 dB-SPL. Usable
frequency response shall extend from 60 Hz to 16 kHz (10 dB below
rated sensitivity, in half-space, with no external equalization). Nominal
impedance shall be 8 ohms. The frequency dividing network shall have
a crossover frequency of 2.8 kHz. Rated power capacity shall be at least
175 watts continuous program power, defined as 3 dB above a test signal
of filtered random noise conforming to international standard IEC268-5
(shaped pink noise with a peak-to-average ratio of 6 dB), for 100
continuous hours duration.
The system shall be protected against damage from occassional
overpowering via full range series lamps that limits the power to the network and transducers. The high frequency transducer shall be hornloaded to more evenly cover a nominal 90° horizontal by 90° vertical
area.
The enclosure shall be constructed of high-impact polystyrene for
protection against the elements in outdoor applications, and for
paintability. The grille shall be completely zinc-coated for resistance
against rusting, shall be bake-painted black, and shall be secured via
screws to keep it in place when facing downward.
The low frequency transducer shall have a polypropelene cone and a
butyl rubber surround which shall extend seamlessly over the edge of
the speaker frame for protection against the elements. The high
frequency transducer shall be constructed of polycarbonate, reinforced
with a titanium film for additional weather resistance. The system shall
withstand Mil Spec 810 testing with specified time durations for
exposure to the following environments with no effect on its acoustical
performance or structural integrity: salt spray (method 509.3),
temperature -19°C to 49°C (method 501.3 and 502.3), 95% humidity
(method 507.3) and ultra-violet (method 505.3). The system shall have a
IEC 529 splashproof rating of IP-34.
For theft deterrence, the installation access area shall be hidden
behind a snap-out cover, and the access area shall be on the front of the
loudspeaker for ease of installation and adjustment. The loudspeaker
shall be rotatable over a minimum of ±35° in all directions via a balltype mounting system. The ball mechanism shall be internal to the
cabinet to allow low-profile mounting and better stability via a short
moment arm. The logo shall be rotatable for proper orientation when
the loudspeaker is mounted horizontally or vertically.
The external wiring connectors shall be spring loaded and gold
plated, and shall accept bare wire, single or dual banana-type
connectors with 19 mm (3/4 in) spacing. Overall cabinet dimensions
shall be no greater than 380 mm (15.0 in) high by 280 mm (11.0 in)
wide by 220 mm (8.6 in) deep and shall weigh no more than 5.5 kg (12
lbs).
The finish shall be a paintable lighly textured black.
The system shall be the JBL Model Control 28 with included Invisiball
®
mounting system.
Page 4
SS Control 28
CRP 5M
03/08
䉴 Control®28 High Output Indoor/Outdoor Background/Foreground Speaker
Vertical 1/3 Octave Polars
JBL Professional
8500 Balboa Boulevard, P.O. Box 2200
Northridge, California 91329 U.S.A.
© Copyright 2008 JBL Professional
A Harman International Company
Loading...