JBL Control 50S/T, Control 52 User Manual
Control Contractor 50 Series
Surface-Mount
Subwoofer-Satellite
Control 50S/T and Control 52
Professional Series
Key Features:
䉴
Stylish, unobtrusive design fits
into a wide variety of decors
䉴
High fidelity sound
䉴
Selectable 70V/100V for
distributed lines, or low
impedance
䉴
Versatility for either two or four
satellite speakers per system
䉴
Ability to mix and match with
Control Contractor40 Series inceiling models
䉴
Wall-mount brackets included
䉴
Available in black or white
The Control 50 Series
subwoofer-satellite loudspeaker
system provides high fidelity
sound in restaurants, retail stores,
music cafes, health clubs, theme
bars, leisure venues, or any
location where full-range high
fidelity foreground/background
music is required from surfacemount system.
Control 52 Satellite Speaker
The stylish Control 52 satellite
loudspeaker produces superb
high fidelity sound via a lowdistortion 60 mm (2½ in) driver,
which features a secondary
bucking magnet for high
efficiency, rubber half roll
surround for enhanced bass
performance, 19 mm (0.75 in)
copper clad aluminum wire voice
coil on a vented Nomex
for high fidelity and reliability,
and a copper-capped pole piece
for more consistent impedance
and extended high frequency
response. The wall bracket allows
each speaker to be angled up to
45° off-axis.
®
former
Loudspeaker System
Control 50 Subwoofer
The 150 Watt (600 Watt peak) Control 50S/T subwoofer contains a
high-power, long-excursion, 200 mm (8 inch) driver which features
an extremely robust high-mass cone for extended low frequency
response, a 38 mm (1.5 in) 4-layer copper voice coil for high motor
strength, an aluminum former for good transient response, and a
rubber half roll surround for enhanced bass performance. The
Control 50S/T’s included two-piece easy-mount wall-bracket installs
quickly: The multi-point wall portion of the bracket attached to the
wall and the self-guiding speaker-mounted bracket drops into place
for a secure attachment. A cover over the Control 50S/T terminal cup
keeps wiring neat. The Control 50S/T is mono. The crossover
network built into the subwoofer provides proper signal routing and
four satellite output connectors allow connection of the wires for the
four Control 52 satellite loudspeakers. A Loop Out connector is also
provided on the subwoofer for looping the full-range input signal to
other loudspeakers or to other subwoofer/satellite systems.
System Configuration
Available as packaged system or as separate items, the Control 50
Series is extremely versatile system. The C50PACK system contains
four Control 52 satellite speakers and one Control 50S/T subwoofer
as an easy predesigned system. For smaller floor spaces, the Control
50S/T subwoofer can be utilized with two Control 52 satellite
speakers. The Control 50 system is mono. Both the Control 50S/T
and Control 52 can be intermixed in systems along with the Control
40 Series in-ceiling models – Control 40CS/T subwoofer and Control
42 satellite speaker – to match the form factor requirements of a
wide variety of applications.
䉴 Control 50S/T and Control 52 Surface-Mount Subwoofer-Satellite Loudspeaker System
Control 50 Subwoofer-Satellite System Specifications
Frequency Range (-10 dB)1: 32 Hz – 20 kHz
Frequency Response (±3 dB)1: 50 Hz – 17 kHz
Nominal Sensitivity (2.83V, 1m)1: 87 dB with 4 satellites
Power Capacity2: 200 Watts Continuous Program Power (100 hrs)
Nominal Impedance: 4 ohms (in bypass/thru mode) with 4 satellites
Transformer Taps: 80W, 40W, 20W, (& 10W @ 70V), plus bypass/thru (listed as 8⍀ on switch to indicate subwoofer impedance)
100 Watts Continuous Pink Noise (100 hrs)
85 dB with 2 satellites
(subwoofer center of wall, higher sensitivity depending on subwoofer boundary loading, see application note)
8 ohms (in bypass/thru mode) with 2 satellites
Control 50S/T Specifications
Frequency Range (-10 dB)1: 32 Hz – 200 Hz
Frequency Response (±3 dB)1: 50 Hz – 150 Hz
Nominal Sensitivity (2.83V, 1m)1: 95 dB (near corner), 89 dB (center of wall)
Rated Maximum SPL (1m): 115 dB average, 121 dB peak (near corner)
Transducer:
Enclosure:
Power Capacity2: 300 Watts Continuous Program Power (2 hrs)
Nominal Impedance: 8 ohms (in bypass/thru mode)
Transformer Taps: 80W, 40W, 20W, (& 10W @ 70V), 8 ohm bypass/thru
Input Connectors: Six removable locking 2-pin connectors with screw-down terminals. Max wire 12 AWG (2.5 mm2)
Material: Top, bottom, front & bottom: Structural plywood. Port & terminal panels: MDF. Grille: Painted zinc-plated metal.
Dimensions (H x W x D): Cabinet: 356 x 391 x 203 mm (14.0 x 15.4 x 8.0 in)
Wall Bracket: 2.3 mm (0.9 in) thick zinc-plated and painted cold-rolled steel
Net Weight: 9.0 kg (20 lbs)
Shipping Weight: 10.2 kg (23 lbs)
Included Accessories: Wall bracket (both speaker and wall parts) with 4 pcs M6 screws to attach to speaker, terminal cover, 6 pcs 2-pin locking
150 Watts Continuous Pink Noise (2 hrs)
200 Watts Continuous Program Power (100 hrs)
100 Watts Continuous Pink Noise (100 hrs)
109 dB average, 115 dB peak (center of wall)
Driver: 200 mm (8 in) with polypropylene cone, butyl rubber surround, 38 mm (1.5 in) 4-layer copper-clad coil, vented aluminum
former
Wall Bracket: 15 mm (0.6 in) deep
connectors, M6 screw for safety lanyard attachment.
Control 52 Specifications
Frequency Range (-10 dB)1: 140 Hz – 20 kHz
Frequency Response (±3 dB)1: 180 Hz – 17 kHz
Nominal Coverage Angle3: 150° x 150° (omnidirectional)
Rated Maximum SPL (1m): 94 dB average, 100 dB peak
Transducer:
Enclosure:
1
Half-space (mounted on wall).
2
Continuous Pink noise rating is IEC-shaped pink noise with a 6 dB crest factor for 100 hours continuously. Continuous Program Power is a conservative expression of the system’s ability to
handle normal speech and music program material, and is defined as 3 dB above the Continuous Pink Noise rating.
3
Half-space, average 1 kHz – 4 kHz
JBL continually engages in research related to product improvement. Changes introduced into existing products without notice are an expression of that philosophy.
Power Capacity2: 50 Watts Continuous Program Power (2 hrs)
Nominal Sensitivity1: 85 dB (4.0V/1m = 1W)
Nominal Impedance: 16 ohms
Input Connector: Removable locking 2-pin connector with screw-down terminals. Max wire 12 AWG (2.5 mm2)
Material: High impact polystyrene, painted zinc-plated metal grille.
Dimensions (H x W x D): Cabinet: 115 x 84 x 96 mm (4.5 x 3.3 x 3.75 in)
Net Weight: 0.7 kg (1.5 lbs)
Shipping Weight: 0.8 kg (1.8 lbs)
Included Accessories: Wall bracket (both speaker and wall parts), 2-pin locking connector.
25 Watts Continuous Pink Noise (2 hrs)
30 Watts Continuous Program Power (100 hrs)
15 Watts Continuous Pink Noise (100 hrs)
82 dB (2.83V, 1m)
Driver: 60 mm (2.5 in) with polypropylene cone, butyl rubber surround, 19 mm (0.75 in) copper-clad coil, vented Nomex®former,
secondary bucking magnet, and copper sleeved pole piece for high frequency extension.
Wall bracket: 51 mm (2.0 in)
Loading...