JBL CBT 200LA-1 User Manual

CBT 200LA-1
Assembly & Bracket Installation Guide
INCLUDED:
op Speaker
Module
Bottom Speaker
Module
Coupler
Plate
M6-34L M6-12L SS Flatwashers
Speaker
Bracket
Swivel-Tilt
Wall Bracket
M6-20L
Flat head
[Not shown to relative scale]
M6-Nuts SS Lockwashers Switch covers
CBT 200LA-1 Assembly & Bracket Installation Guide – Page 2
WALL BRACKET
Note that the
BRACKET ASSEMBLY
1) RUN WIRING
WALL SURFACE MOUNTING
consists of a
SPEAKER BRACKET
-- Run the wiring from the power amplifier to the location desired for mounting the
and a
JBL CBT Loudspeakers.
2) ATTACH
straight, secure the
WALL BRACKET
WALL BRACKET
TO WALL
-- Using a level to ensure that the
WALL BRACKET
to the wall. Be sure to use the appropriate wall anchors for attaching the bracket. Use all four screw holes for maximum integrity and safety. Be sure that the slot feature is at the top.
is
.
Hardware for attaching
WALL BRACKET
to wall not included.
CBT 200LA-1 Assembly & Bracket Installation Guide – Page 3
3) ORIENTING TOP & BOTTOM SPEAKER MODULES
This drawing shows the proper orientation of the two speaker modules, where the coupler plate attaches and where the wall bracket attaches (onto the coupler plate).
IMPORTANT: Note that the speaker will not work correctly if the
SPEAKER MODULES
Swivel/Tilt
Wall Bracket
(4 panhead bolts)
are not oriented exactly as shown.
TOP SPEAKER MODULE
Coupler Plate
(8 flathead bolts)
CBT 200LA-1 Assembly
1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other
2) Attach Coupler Plate Using 8 Included Flathead Bolts
CAUTION: Installation must be done by qualified persons using safe rigging standards.
Switches at the End of the Column
Labels Show Orientation and Gives Instructions (Point Arrows Toward Each Other)
For Top Module:
CBT 200LA-1 Assembly
1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other
2) Attach Coupler Plate Using 8 Included Flathead Bolts
CAUTION: Installation must be done by qualified persons using safe rigging standards.
TOP AND BOTTOM
BOTTOM SPEAKER MODULE
Switches at the End of the Column
CBT 200LA-1 Assembly
1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other
2) Attach Coupler Plate Using 8 Included Flathead Bolts
CAUTION: Installation must be done by qualified persons using safe rigging standards.
For Bottom Module:
CBT 200LA-1 Assembly
1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other
2) Attach Coupler Plate Using 8 Included Flathead Bolts
CAUTION: Installation must be done by qualified persons using safe rigging standards.
CBT 200LA-1 Assembly & Bracket Installation Guide – Page 4
4) CONNECT SPEAKER MODULES TOGETHER VIA COUPLER PLATE
Attach
COUPLER PLATE
pcs of M6-20L flathead bolts, through to
to the
TOP AND BOTTOM SPEAKER MODULES
TOP AND BOTTOM SPEAKER MODULE’S
, as shown, with 8
cabinet insert points.
5) ATTACH SPEAKER BRACKET TO 4 THREADED HOLES ON COUPLER PLATE
Attach Speaker Bracket to the 4 indicated threaded points on the Coupler Plate using the included M6-12L (6 mm diameter, 12 mm long) bolts, with lock washers and flat washers.
rear
M6L12
BOLT
LOCK
WASHER
FLAT
WASHER
[4 Places]
Speaker Section of
Speaker/Wall Bracket
Threaded points for attachment of Wall Bracket (use included M6 x 12 mm pan-head bolts)
Threaded points for attachment of Wall Bracket (use included M6 x 12 mm pan-head bolts
Assembly
IMPORTANT: Because of the height of this speaker, the speaker bracket MUST be installed to these threaded points on the Coupler Plate. Do NOT install the bracket to any other positions on the speaker
.
Coupler Plate
(already installed on speaker)
CBT 200LA-1 Assembly & Bracket Installation Guide – Page 5
6) SLIDE SPEAKER WITH
SPEAKER BRACKET
ONTO
WALL BRACKET
Once the wall mount has been attached to the wall and speaker mount ha s been attached
n
to the speaker, loosely install the M6-L34
PIVOT BOLT
one side and flat washer, lock washer & nut on the other side) of the slide the speaker so that the dropping the hook slot of the
installed loosely in the
WALL BRACKET
SPEAKER BRACKET
SPEAKER BRACKET
),
as shown in Drawing n .
engages into the
onto the
(bolt, lock washer and flat washer on
WALL BRACKET.
WALL BRACKET
PIVOT BOLT
(which will already be
Then
,
LOCK
M6 NUT
WASHER
PIVOT BOLT LOCATION
1
FLAT
WASH ER
2
FLAT
WASH ER
LOCK
WASH ER
[Same hardware order
for both bolts]
M6-34L
BOLT
3
CBT 200LA-1 Assembly & Bracket Installation Guide – Page 6
Insert the top tilt-angle bolt through the appropriate hole – one of the preset angle holes or the
o
slot for continuous adjustment capability (see below for more information about tile angles). Install with M6-L34 bolt, lock washer and flat washer on one side and flat washer, lock washe r &
nut on the other side, as shown in Drawing
BRACKET
and in
SPEAKER BRACKET
. Make sure bolt goes through holes in
o
.
WALL
Final
p
TIGHTEN THE BOLTS
BRACKET ASSEMBLY
.
is shown in Drawing p .
7) MORE ABOUT TILT ANGLES --
because of the height of this speaker, the end of the speaker hits the wall at any angle greater than 10 degrees.
PRE- SET ANGLES
for mounting angles of +/- 15 degrees in 5 degree increments. There is also a slot above the set of holes for continuously variable adjustment. The pre-set angles are recommended for accurate aiming in 5 degree increments and the slot for any angle between 5 degree increments. Either can be utilized for setting the speaker’s tilt angle.
and
CONTINUOUSLY VARIABLE ANGLE
The bracket allows for +/-15 degrees of up or down tilt, however
-- The bracket has through holes
8) SET THE SWIVEL (PAN) ANGLE
side-to-side swivel (ie, pan) aiming angle of the speaker. Tighten the bolts securely.
Maximum Swivel Angles before Wall Interference
side-to-side, however when mounting the CBT speaker onto a wall, the side-to-side swivel is limited by the end of the speaker encountering the wall. The maximum swivel angle depends on the up/down tilt angle setting.
9) SAFETY CABLE
the CBT 200LA-1 cabinet using one of the extra included M6 bolts or via an M6 forged shoulder steel eyebolt. Attach the other end of the cable to a secondary attachment point on the wall.
10) SWITCH COVERS –
provided. Peel off the backing from the switch cover and stick the cover over the switch shaft, lining up the ridge with the recess in the switch shaft.
-- Attach a safety cable (not included) to any of the 6 mm inserts on the back of
To discourage tampering with the switch settings, adhesive switch covers are
– Loosen the top and bottom bolts on the pivot. Adjust the
– The bracket swivels a full 90 degrees from
CBT 200LA-1 Assembly & Bracket Installation Guide – Page 7
11) USING OPTIONAL MTC-CBT-FM1 FLUSH-MOUNT WALL BRACKETS
CBT-FM1 brackets allow installing the speaker with its back very close to the wall. It is recommended to use two brackets – one on the top and one on the bottom – for stability.
– The optional MTC-
CBT 200LA-1 Assembly & Bracket Installation Guide – Page 8
CBT 200LA-1 Bracket Dimensions
JBL Professional 8500 Balboa Blvd. Northridge, CA 91355 USA
CBT200 Install
07/12
Loading...