Page 1
JBL Incorporated, 8500 Balboa Boulevard, P.O.Box 2200, Northridge, California 91329 U.S.A.
JBL AM7212/95-WH
REV B
PACKAGE
WIRING DIAGRAM
02-10
Technical Manual
JBL AM7212/95-WH
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• Nominal Impedance: 8 Ohms
• Transducer Power LF: 1000W (4000W peak), 2 hrs
Rating (AES): 700W (2800W peak), 100 hrs
HF: 100W (400W peak), 2 hrs
• Long-Term Power Passive mode:600W (2400W peak),
Rating (IEC): 100 hrs
• Frequency Response: 42 Hz - 18 kHz (±3 dB)
• Frequency Range: 36 Hz - 20 kHz (-10 dB)
• Maximum SPL:
Bi-amp mode: LF: 126 dB-SPL cont avg (132 dB peak)
HF: 133 dB-SPL cont avg (139 dB peak)
Passive mode: 123 dB-SPL cont avg (129 dB peak)
• System Sensitivity: Passive mode:95 dB SPL
1 watt @ 1 meter
• Passive Crossover
Frequency: 1.4 kHz
SYSTEM COMPONENTS:
• Cabinet: Enclosure (Not For Sale)
• Grille: 338163-007, 338163-107 (WH)
• Low Frequency 2262HPL, 300 mm (12 in)
SYSTEM COMPONENTS:
(CONT’D)
Transducer: Differential Drive®, driver with 75 mm
(3 in) dual voice coil
• DC Resistance: 5.1 ohm
• High Frequency 2432H, 38 mm (1.5 in) exit
Transducer: compression dr iver,75 mm (3 in)
voice coil
• DC Resistance: 4.00 ohm +/- 0.2 ohm
• Crossover Network: 443838-001
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 7.0V Input, 10 Hz to 10 kHz
Sweep Duration: 5 seconds
B. L.F. Aural Sweep Test: 10V Input, 10 Hz to 1 kHz
C. H.F. Aural Sweep Test: 3.0V Input, 300 Hz to 1.0 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions: 711 x 369 x 458 mm D
(28.0 x 14.5 x 18.0 in.D.)
• Net Weight: 51 lb (23.1 kg.)
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
YEL/BLK
GRN/BLK
GRN
YEL
Network Assembly
443838-001
Driver, Low Freq.
2262HPL
(338312-004X)
Cone Repl
C8R2262
Driver, High Freq
2432H
(365512-001X)
Diaph Repl
D8R2432
SEE NETWORK SCHEMATICPAGE
Carton
352188-001
Filler (2)
352187-001
PKG,Microfoam (4)
49790P
20” x 18” Sheets
Warranty
59660
Installation Sheet
339390-067
Sticker, Logo
339397-001
Bag
21784
NOTE: INDIVIDUAL PARTS FOR THE ABOVE CROSSOVER ARE NOT AVAILABLE.
A COMPLETE REPLACEMENT ASSEMBLY SHOULD BE ORDERED.
Page 2
SCHEMATIC (443838-001)
JBL AM7212/95-WH
JBL AM7212/95-WH
Individual Parts for the above crossover are not available.
A complete replacement assembly should be ordered.
1.30mH
1.30mH
4.00mH
0.400mH
0.150mH
0.160mH
0.091mH
33.uF
250V
27.0uF
250V
12.0uF
250V
3.01uF
250V 2%
16.0uF
250V
18.0uF
250V
3.60uF
250V
4.70uF
250V
70.0 Ohms
70.0
Ohms
2.2 Ohms
2.7 Ohms
0.75 Ohms
GRN/BLK
GRN
GRN
RED
BLK
YEL
YEL/BLK
YEL
+ 0.187
- 0.250
8 Pin
Connector
Molex P/N
39-01-2080
-
+
Page 3
COMPONENT EXPLODED VIEW
JBL AM7212/95-WH
JBL AM7212/95-WH
Grille Assembly
338163-007
338163-107 (WH)
Screw (6)
882-51110-12
882-51160-12 (WH)
6 x 3/4
OV,PH,PTCL
ZINC,LCS
Driver, Low Freq.
2262HPL
(338312-004X)
Cone Repl
C8R2262
Screw (8)
804-01110-16
10-32 x 1
FIL,PH,BLK
ZINC,LCS
Gasket
339391-001
12”
Grille Support (2)
338623-001
Network Assembly
443838-001
Screw (8)
882-41110-10
6 x 5/8
PAN,PH,PB
BLK ZINC,LCS
Input Plate
339336-001
Screw (6)
882-41110-10
6 x 5/8
PAN,PH,PB
BLK ZINC, LCS
Input Label (HADM)
440926-005
Label
339339-079
339339-179 (WH)
Bolt (15)
352051-001
352051-002 (WH)
M10 x 25MM
HEX
Driver, High Freq. ThreadLock
2432H 352951-001
(365512-001X) 9 Gram Stick
Diaph Repl Loctite 248
D8R2432
Nut (4)
Stud (4) 834-30010-00
75815 1/4 KEPS
1/4-20 x 1.5”LG BLK ZINC,
LCS,RIGHT
Waveguide
443495-001
Screw (8)
804-41110-12
10-32 x 3/4
PAN,PH,BLK
ZINC, LCS
Logo, Grille
339401-001
339401-002 (WH)
Push Nut
350689-001
Compression Spring
350690-001
Washer
76168
BLK.715ID .75OD
Enclsoure Assembly
AM7212/95-WH
(Not Available for Sale)
Mounting Support (6)
381-00023-01
90 Degrees 2X M10
(internal)
Screw (12)
883-41110-08
8 x 1/2
PAN,PH,PB,BLK
ZINC,LCS
Mounting Bracket (3)
338652-001
(internal)
Screw (6)
883-41110-08
8 x 1/2
PAN,PH,PB,BLK
ZINC,LCS
Loading...