JBL Incorporated, 8500 Balboa Boulevard, P.O.Box 2200, Northridge, California 91329 U.S.A.
JBL AM5215/95-WH
REV B
PACKAGE
WIRING DIAGRAM
01-10
Technical Manual
JBL AM5215/95-WH
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• Nominal Impedance: 8 Ohms
• Transducer Power
Rating (AES): LF: 500W (2000W peak), 2 hrs
350W (1400W peak), 100 hrs
HF: 40W (160W peak), 2 hrs
• Long-Term Power
Rating (IEC): Passive mode:350W (1400W peak),
100 hrs
• Frequency Response: 41 Hz - 18 kHz (±3 dB)
• Frequency Range: 35 Hz - 20 kHz (-10 dB)
• Maximum SPL:
Bi-amp mode: LF: 125 dB-SPL cont avg (131 dB peak)
HF: 129 dB-SPL cont avg (135 dB peak)
Passive mode: 124 dB-SPL cont avg (130 dB peak)
• System Sensitivity: Passive mode:98 dB SPL
1 watt @ 1 meter
• Crossover Frequency: 1.8 kHz
SYSTEM COMPONENTS:
• Cabinet: Enclosure (Not For Sale)
• Grille: 338163-002, 338163-102 (WH)
SYSTEM COMPONENTS:
(CONT’D)
• Low Frequency: 265H-1, 380 mm (15 in) driver
Transducer: with 50.8 mm (2 in) dual voice coil
• DC Resistance: 5.25 ohm +/- 10%
• High Frequency 2408H-1, 38 mm (1.5 in) exit
Transducer: compression driver, 38 mm (1.5 in)
voice coil
• DC Resistance: 4.80 ohm +/- 0.2 ohm
• Crossover Network: 443677-001
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 7.0V Input, 10 Hz to 10 kHz
Sweep Duration: 5 seconds
B. L.F. Aural Sweep Test: 7.0V Input, 10 Hz to 300 Hz
C. H.F. Aural Sweep Test: 0.75V Input, 200 Hz to 1.5 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions: 783 x 422 x 504 mm D
(30.8 x 16.6 x 19.85 in.D.)
• Net Weight: 55 lb (25.0 kg.)
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
YEL/BLK
GRN/BLK
GRN
YEL
Network Assembly
443677-001
Driver, Low Freq.
265H-1
(363837-003X)
Cone Repl
C8R265
Driver, High Freq
2408H-1
(365011-001X)
Diaph Repl
D8R2408-1
SEE NETWORK SCHEMATICPAGE
Carton
351684-001
Filler (2)
351408-001
PKG,Microfoam (6)
49790P
20” x 18” Sheets
Warranty
59660
Installation Sheet
339390-062
Sticker, Logo
339398-001
Bag
21784
NOTE: INDIVIDUAL PARTS FOR THE ABOVE CROSSOVER ARE NOT AVAILABLE.
A COMPLETE REPLACEMENT ASSEMBLY SHOULD BE ORDERED.
SCHEMATIC (443677-001)
JBL AM5215/95-WH
JBL AM5215/95-WH
Individual Parts for the above crossover are not available.
A complete replacement assembly should be ordered.
1.75mH
5.00mH
0.200mH
0.620mH
0.030mH
0.200mH
16.0uF
250V
14.0uF
250V
20.0uF
250V
1.62uF
250V 2%
10.0uF
250V
10.0uF
250V
14.0uF
250V
40.0 Ohms
40.0 Ohms
3.3 Ohms
GRN/BLK
GRN
YEL/BLK
YEL
GRN
RED
BLK
YEL
+ 0.187
- 0.187
+ 0.250
- 0.250
8 Pin
Connector
Molex P/N
39-01-2080
COMPONENT EXPLODED VIEW
JBL AM5215/95-WH
JBL AM5215/95-WH
Grille Assembly
338163-002
338163-102 WH)
Screw (8)
882-51110-12
882-51160-12 (WH)
6 x 3/4
OV,PH,PTCL,
ZINC,LCS
Driver, Low Freq.
265H-1
(363837-003X)
Cone Repl
C8R265
Screw (8)
804-01110-16
10-32 x 1
FIL, PH,BLK ZINC
LCS
Gasket, Rear
360-70002-01
15”
Dome
71646-04
T-Nut (16)
61861
10-32 x 7/16
Step Barrel
Mounting Support (6)
381-00023-01
90 DEGREES
Bolt (15)
352051-001
352051-002 (WH)
M10 x 25MM, HEX
Screw (12)
883-41110-08
8 x 1/2
PAN,PH,PB,BLK ZINC,LCS
Mounting Bracket (3)
338652-001
FLAT SINGLE, M10
Screw (6)
883-41110-08
8 x 1/2
PAN,PH,PB,BLK ZINC,LCS
Network
Asembly
443677-001
Screw (9)
882-41110-10
6 x 5/8
PAN,PH,PB
BLK ZINC,LCS
Input Plate
339336-001
Screw (6)
882-41110-10
6 x 5/8
PAN,PH,PB,
BLK ZINC,LCS
Input Label (HADM)
440926-007
Label
339339-067
Driver, High Freq.
2408H-1
(365011-001X)
Diaph Repl
D8R2408-1
Throat Adapter
443323-001
Bolt (4)
854-03010-16
1/4-20 x 1
CAP,BLK ZINC,
LCS
Nut (4)
834-30010-00
1/4-20
KEPS,BLK
ZINC, LCS
RIGHT
Waveguide
443495-001
Screw (8)
804-41110-12
10-32 x 3/4
PAN,PH,BLK
ZINC,LCS
Logo, Grille
339402-001
339402-002 (WH)
Push Nut
350689-001
7/16”
Compression Spring
365201-001
Washer
76168
BLK.175ID .75OD
Enclosure Assembly
AM5215/66-WH
(not available for sale)
Loading...