JBL Incorporated, 8500 Balboa Boulevard, P.O.Box 2200, Northridge, California 91329 U.S.A.
JBL AM5212/66-WH
REV C
PACKAGE
WIRING DIAGRAM
01-10
Technical Manual
JBL AM5212/66-WH
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• Nominal Impedance: 8 Ohms
• Transducer Power LF: 400W (1600W peak), 2 hrs
Rating (AES): 300W (1200W peak), 100 hrs
HF: 40W (160W peak), 2 hrs
• Long-Term Power Passive mode:300W (1200W peak),
Rating (IEC): 100 hrs
• Frequency Response: 43 Hz - 20 kHz (±3 dB)
• Frequency Range: 37 Hz - 20 kHz (-10 dB)
• Maximum SPL:
Bi-amp mode: LF: 122 dB-SPL cont avg (128 dB peak)
HF: 130 dB-SPL cont avg (136 dB peak)
Passive mode: 121 dB-SPL cont avg (127 dB peak)
• System Sensitivity: Passive mode:96 dB SPL
1 watt @ 1 meter
• Crossover Frequency: 2 kHz
SYSTEM COMPONENTS:
• Cabinet: Enclosure (Not For Sale)
• Grille: 338163-007, 338163-107 (WH)
SYSTEM COMPONENTS:
(CONT’D)
• Low Frequency Driver: 262H-1, 300 mm (12 in) driver
Transducer: with 50.8 mm (2 in) dual voice coil
• DC Resistance: 5.5 ohm +/- 10%
• High Frequency 2408H-1, 38 mm (1.5 in) exit
Transducer:: compression driver,38 mm (1.5 in)
voice coil
• DC Resistance: 4.80 ohm +/- 0.2 ohm
• Crossover Network: 443547-001
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 7.0V Input, 20 Hz to 20 kHz
B. L.F. Aural Sweep Test: 7.0V Input,10 Hz to 1 kHz
C. H.F. Aural Sweep Test: 0.75V Input, 200 Hz to 1.5 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions: 713 x 371 x 458 mm D
(28.06 x 14.6 x 18.1in.D.)
• Net Weight: 45 lb (20.2 kg.)
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
YEL/BLK
GRN/BLK
GRN
YEL
Network Assembly
443547-001
Driver, Low Freq.
262H-1
(363916-003X)
Cone Repl
C8R262
Driver, High Freq
2408H-1
(365011-001X)
Diaph Repl
D8R2408-1
SEE NETWORK SCHEMATICPAGE
Carton
352188-001
Filler (2)
352187-001
PKG,Microfoam (4)
49790P
20” x 18” Sheets
Warranty
59660
Installation Sheet
339390-060
Sticker, Logo
339397-001
Bag
21784
NOTE: INDIVIDUAL PARTS FOR THE ABOVE CROSSOVER ARE NOT AVAILABLE.
A COMPLETE REPLACEMENT ASSEMBLY SHOULD BE ORDERED.
SCHEMATIC (443547-001)
JBL AM5212/66-WH
JBL AM5212/66-WH
1.5uF
250V 2%
11uF
250V
340nF
250V 2%
4.2uF
250V 2%
10.2uF
250V
950nF
250V 2%
0.51mH
0.215mH
0.42mH
0.87mH
1.85mH
2.5mH
5.0 Ohms
6.0
Ohms
3.0
Ohms
7.5
Ohms
4.0 Ohms
YEL
BLK
RED
GRN
GRN
GRN/BLK
YEL/BLK
YEL
GRN
Individual Parts for the above crossover are not available.
A complete replacement assembly should be ordered.
- 0.187
+ 0.187
+ 0.250
- 0.250
8 Pin
Connecotr
Molex P/N
39-01-2080
COMPONENT EXPLODED VIEW
JBL AM5212/66-WH
JBL AM5212/66-WH
Grille Assembly
338163-007
338163-107 (WH)
Screw (8)
882-51110-12
882-51160-12 (WH)
6 x 3/4
OV,PH,PTCL
ZINC,LCS
Driver, Low Freq.
262H-1
(363916-003X)
Cone Repl
C8R262
Screw (8)
804-01110-16
10-32 x 1
FIL,PH,BLK ZINC,
LCS
Gasket
339391-001
Dome
31385-09
Network Assembly
443547-001
Screw (7)
882-41110-10
6 x 5/8
PAN.PH,PB,BLK
ZINC,LCS
Mounting Bracket (3)
338652-001
Flat Single M10
Screw (6)
883-41110-08
8 x 1/2
PAN,PH,PB,BLK
ZINC,LCS
Mounting Support (6)
381-00023-01
90 DEGREES 2X M10
Bolt (15)
352051-001
352051-002 (WH)
M10 x 25MM,HEX
Screw (12)
883-411110-08
8 x 1/2
PAN,PH,PB,BLK
ZINC,LCS
Input Plate
339336-001
NL4
Screw (6)
882-41110-10
6 x 5/8
PAN,PH,PB,BLK
ZINC,LCS
Input Label (HADM)
440926-007
Label
339339-065
T-Nut (16)
61861
10-32x7/16
Step Barrel
Driver, High Freq.
2408H-1
(365011-001X)
Diaph Repl
D8R2408-1
Throat Adapter
443323-001
Bolt (4)
854-03010-16
1/4-20 x 1
CAP,BLK ZINC,LCS
Nut (4)
834-30010-00
1/4-20
KEPS,BLK ZINC,
LCS, RIGHT
Waveguide
443454-001
Screw (8)
804-41110-12
10-32 x 3/4
PAN,PH,BLK ZINC,
LCS
Logo, Grille
339401-001
339401-002 (WH)
Push Nut
350689-001
7/16”
Compression Spring
365201-001
Washer
76168
BLK.175ID .75OD
Enclosure Assembly
AM5212/66-WH
(Not Available for Sale)
Loading...