INSTRUCTION MANUAL
WS140
High-Temperature
Wire Stipper
Index
1. Pac king List ....................................................................................................................... 3
2. Features & Connections .................................................................................................. 4
3. Changing Cartridge s ........................................................................................................ 5
4. Cartridge Ran ge .............................................................................................................. 6
5. Adjusta ble Strip Gauge .................................................................................................. 8
6. Stri pping a Wire ............................................................................................................... 8
7. Sa fet y ................................................................................................................................. 9
8. Specif ications .................................................................................................................. 12
Page
2
This manual corresponds to the following reference:
WS140-A
Packing List
The following items are included:
High-Temperature Wire Stripper ............................................... 1 unit
www.jbctools.com
Metal Brush................................................1 unit
Ref. 0022793
Manual ............................................... 1 unit
Ref. 0025147
3
Features and Connections
WSU Control Unit
(not included)
USB Connector
Equipotential Connector
Main Switch
Stand Cable
Ref. 00112 8 3
(not included)
Fuse
Stand
Ref. WS-SB
(not included)
Power Socket
W140 Cartridges
(not included)
High-Temperature
Wire Stripper
Re f. WS140 -A
4
www.jbctools.com
Changing Cartridges
2. Inserting and Positioning 1. Removing
WS140
Blade Cartridges
Alignment
Loosen the screws and remove the cartridges. Insert the new cartridges. Before tightening the
screw, align the tip edges and fix the cartridges
in working position.
3. Fixing
Cartridge Electric
Connection Screw
Important: It is essential to tighten the screws
for the tool to function.
Important: It is esential to insert the cartridge till the end for a good connection. Insert the cartridge
until the reference ring touch against the Wire Stripper. Take the ring as reference and check that
both tips match.
Reference Ring
5
Accessories
Flat Screw Driver
To open or fix the Wire Stripper srews use the JBC Flat Screw Driver Ref. 0023074.
Cartridge Extractor
To manipulate the cartridges use the JBC Cartridge Extractor Pliers Ref. PLR195. More nformation at
www@jbctools.com
Removing Inserting and Positioning
Align cartridges with JBC pliers.Remove cartriges with JBC pliers.
6
www.jbctools.com
Cartridge Range
The WS140-A works with W140 blade cartridges. Find the model that best suits your soldering needs
on www.jbctools.com.
Cartridge
Ref.
W14040G
W14038G
W14037G
W14036G
W14034G
W14032G
W14030G
W14028G
W14026G
W14024G
Cartridge
Ref.
W14022G
W14020G
W14018G
Tip Hole ø
mm / in
0,08 / 0,0031
0,10 / 0,0039
0,11 / 0,0043
0,13 / 0,0051
0,16 / 0,0063
0,20 / 0,0079
0,25 / 0,0098
0,32 / 0,0126
0,40 / 0,0157
0,51 / 0,0201
Tip Hole ø
mm / in
0,64 / 0,0252
0,81 / 0,0319
1,02 / 0,0402
AWG
Solid
40
38
37
36
34
32
30
28
26
24
AWG
Solid
22
20
18
AWG
Stranded
x
x
x
x
36 (7x44)
34 (7x42)
32 (19x44)
30 (7x38)
30 (19x42)
28 (19x40)
27 (7x35)
26 (19x38)
26 (19x38)
AWG
Stranded
24 (19x36)
24 (7x32)
22 (19x34)
20 (42x36)
20 (19x32)
20 (7x28)
9 mm
0.354 in
9 mm
0.354 in
3 mm
3 mm
0.118 in
0.118 in
Cartridge
Ref.
W14003F
Tip
mm / in
Flat Tip
3 / 0.118
9 mm
0.354 in
3 mm
0.118 in
7
Cartridge
Ref.
Tip Hole ø
mm / in
AWG
Solid
AWG
Stranded
W14016G
W14014G
Cartridge
Ref.
W14005F
1,29 / 0,0508
1,63 / 0,0642
16
14
Tip
mm / in
Flat Tip
5 / 0.197
18 (19x30)
16 (7x24)
10.5 mm
0.413 in
10.5 mm
0.413 in
5 mm
5 mm
0.197 in
0.197 in
If an application require a special tip design, contact JBC on customtips@jbctools.com for special
blade cartridges.
8
www.jbctools.com
Adjustable Strip Gauge
Adjust the strip gauge according to your stripping requirements and tighten the screw.
Strip Gauge
Stripping a Wire
1. Adjust Arm Position 2. Align Wire
arm position accordig to the wire diameter.
Move the wheel backward for a wider and
forward for a narrower position.
3. Close Cartridges
Choose cartridges according to the wire
diameter. Pinch the wire with the blades. The
pinched area will be melted by heat.
Place the wire touching the strip gauge. The wheel allows to adjuste the Wire Stripper
4. Remove Wire
Pull the Wire Stripper toward to stripp off
the wire end.
9
Safety
Warning
- Do not touch the blade or the metal parts arround.
- Do not allow the blade be close to flammable materials.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved.
- Maintenance must not be carried out by children unless super vised.
- Place the tool on the stand when is not in use.
- Turn off the power when not in use, changing parts or storing.
Caution
- Do not use the Wire Stripper for other applications than wire stripping.
- Do not modify or customize the Wire Stripper.
- Do not hit the blade against workbench to eliminate stripped insulation debris, This behavior
would damage the blade.
- Remove power from the tool by holding the plug, not the wires.
- Be careful with the fumes produced when stripping. We recomend to use a fume extractor.
10
www.jbctools.com
11
Specifications
WS140-A
- Max. power per cartridge: 40W
- Cable length: 1,2 m (47.2 in)v
- Dimensions / Weight: 109 x 34 x 16 mm/ 0.12 kg
(L x W x H) 4.29 x 1.36 x 0.63 in / 0.26 lb
- Package Dimensions / Weight: 277 x 73 x 50 mm / 0.16 kg
(L x W x H) 10.91 x 2.87 x 1.97 in / (0.35lb)
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warrant y does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
Get 1 extra year JBC warrant y by registering here:
https://www.jbctools.com/productregistration/
within 3 0 days of purchase.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
www.jbctools.com
00 2514 7-0 32 1
Loading...