JBC Tools RWT-B User Manual

www.jbctools.com
Rework Adjustable Arm
Ref. RWT-B
Packing List
The following items should be included:
Tool Arm ......................... 1 u nit Flange ............................. 1 un it
Ref . 0017524
Flange Screw ..... 3 u
Ref. 0017548
Adapters ...................................................... 1 unit
Ref. 0017058 (for JT-TA Heater)
Flange Nut .......... 3 u
Ref. 0892422
Flange Washer .. 3 u Ref. 0919480
Manual ......................................................... 1 unit
Ref. 0020500
0017059 (for TE-TB Precision Heater)
Allen screw .................... 1 unit
Ref . 0017057
Allen key ......... 1 un it
Ref. 0013609
www.jbctools.com
Rework Adjustable Arm
Ref. RWT-B
2
Features
Ideal for working with JBC’s Hot Air stations and Preheaters.
www.jbctools.com
Tool Holder
Adjust the tool head holder position according to your work needs
Turn the lever to lower the tool
When you have finished raise the tool to free up the workspace.
Hose Clamp
Vertical axis with ruler
IR Preheater Support
Ref. PHS-SA
to Hot Air stations
3
Assembly
1. Fixing the Flange 2. Setting up the Tool Arm
Screw
Washer
Nut
Fix the flange on your work table with the supplied screws, nuts and washers.
3. Inserting the Adapter (JT/TE)
Adapter
Slide the adapter along the hose to the end of the handle.
Allen key
Fit the tool arm onto the flange and tighten the allen screw.
4. Mounting the Tool
Insert the tool as far as possible.
5. Place the hose in the clamp
4
www.jbctools.com
Height adjustment
- The RWT-B Arm allows adjustment for different heights according to your work needs through the vertical axis rule.
- Slide the tool holder to the appropriate height and secure by tightening the lower knob to guarantee stability. Make sure the upper knob is loosened before sliding the tool holder.
Upper knob
Lower knob
Work position adjustment
The RWB-B arm allows adjustment for different positions according to your work needs. The articulated arm covers all work areas.
Top view
Position the arm and tighten the knobs.
5
Tool Holder adjustment
Wheel
Button Tool head
Tilting movement:
The Tool Holder for Rework Arm allows you to adjust the tool head holder position to suit your work needs.
Press the button or loosen the wheel to move the ball joint.
Both axes have a ruler to carry out the task with higher precision .
holder
By holding down the button you can rotate the Tool Holder up or down.
Rotation movement:
You can lock or unlock the lateral rotation mechanism by turning the fixing wheel a quarter.
6
The movement allows a rotation of -40º to +40º.
The movement allows a rotation of -90º a +90º.
Maintenance
- Check periodically that the RWT-B is clean, especially the sliding par ts and the shaft.
- Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.
www.jbctools.com
- Replace any defective or damaged parts.
Use original JBC spare parts only.
- Repairs should only be performed by a
JBC authorized technical service.
Keep the sliding
parts clean
Safety
It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosions.
- Do not use the equipment for any purpose other than PCB rework. Incorrect use may cause fire.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight as well as persons with reduced
physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
7
Exploded View
8
www.jbctools.com
9
Notes
10
www.jbctools.com
11
Specifications
- Tot a l weight: 4 kg (8.8 lb)
- Height: 386,5 mm (15.2 in)
- Arm lenght: 444,5 mm (17.5 in)
- ESD safe connector
Complies with CE standards ESD Safe
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warrant y does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Register your warranty within 30 days of purchase in www.jbctools.com/productregistration
This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facilit y.
Manual in other languages available on our website
www.jbctools.com
0020500-1018
Loading...