How it Works
JBC Tools
Loading...
GSF07D-B
User Manual
12 pgs4.86 Mb0

JBC Tools GSF08V-B, GSF15V-B, GSF10V-B, GSF12V-B, GSF16V-B User Manual

...
Download
INSTRUCTION MANUAL
GSF
Guide Kits for SF280
This manual corresponds to the following references:
With Solder Wire Perforation:
GSF08V-B for wire Ø 0.8 mm / Ø 0.032 in GSF10V-B for wire Ø 1.0 mm / Ø 0.040 in GS F12V-B for wire Ø 1.2 mm / Ø 0.047 in GS F15V-B for wire Ø 1.5 mm / Ø 0.059 in GSF16V-B for wire Ø 1.6 mm / Ø 0.063 i n
Without Solder Wire Perforation:
GSF04D-B for wire Ø 0.38 - 0.40 mm / Ø 0.015 - 0.016 in GSF05D-B for wire Ø 0.46 - 0.56 mm / Ø 0.018 - 0.022 in GSF06D-B for wire Ø 0.60 - 0.64 mm / Ø 0.023 - 0.025 in GSF07D-B for wire Ø 0.70 - 0.78 mm / Ø 0.028 - 0.031 in GSF08D-B for wire Ø 0.80 - 0.82 mm / Ø 0.032 - 0.033 in GSF10 D -B for wire Ø 0.90 - 1.10 mm / Ø 0.036 - 0.044 in GS F12D - B for wire Ø 1.14 - 1.27 mm / Ø 0.045 - 0.051 in GSF15D-B for wire Ø 1.50 - 1.57 mm / Ø 0.060 - 0.062 in GSF16 D-B for wire Ø 1.60 - 1.63 mm / Ø 0.063 - 0.065 in GSF18 D -B for wire Ø 1.80 mm / Ø 0.073 in
GSF Guide Kit for SF280 with Solder Wire Perforation
Guide Tube
Outlet Nozzle
Headless Screws
Inlet Nozzle
Allen Screws
Intermediate Noz zle
Guide Wheel
Counter Wheel
Blade Clamp
Blade
Packing List
Guide Tube* ............................................. 1 unit
Inlet Nozzle* ............................................. 1 unit
Guide Wheel* ........................................... 1 unit
Counter Wheel* ....................................... 1 u nit
Blade Clamp* ........................................... 1 unit
Blade* ......................................................... 1 unit
Intermediate Nozzle* ............................. 1 unit
Outlet Nozzle* .......................................... 1 unit
*references see table on page 4
2
Allen Screws* ......................................... 2 units
Headless Screws* ................................ 3 units
Manual ....................................................... 1 unit
Ref. 0028099
GSF Guide Kit for SF280 without Solder Wire Perforation
para manuales - color gris
Guide Tube
Outlet Nozzle
Inlet Nozzle
Allen Screws
Headless Screws
Intermediate Noz zle
Traction Wheel
Support Wheel
Counter Wheel
Packing List
Guide Tube* ............................................. 1 unit
Inlet Nozzle* ............................................. 1 unit
Traction Wheel* ....................................... 1 un it
Support Wheel* ....................................... 1 unit
Counter Wheel* ....................................... 1 u nit
Intermediate Nozzle* ............................. 1 unit
Outlet Nozzle* .......................................... 1 unit
*references see table on page 5
Allen Screws* ......................................... 2 units
Headless Screws* ................................ 3 uni ts
Manual ....................................................... 1 unit
Ref. 0028099
3
GSF Guide Kit for SF280 with Solder Wire Perforation
4
GSF Guide Kit for SF280
para manuales - color gris
without Solder Wire Perforation
5
325
ºC
24.0
mm/s
75%
Con�nuous
50%
Sel. temp. 325
º
C
Ø 1.00 mm
Supplied: 12 mm
Tin reload process
Mode
Con�nuous
20.0mm/s
1.00mm
Off
5.0mm
Speed
Wire diameter
Feeder parameters lock
Backward
Back
325
ºC
24.0
mm/s
25%
75%
Power
Con�nuous
50%
Sel. temp. 325
º
C
Ø 1.00 mm
Supplied: 12 mm
Feeder parameters lock
20.0mm/s
1.00mm
Off
5.0mm
Speed
Tin reload process
Wire diameter
Backward
Back
Mode
Con�nuous
325
ºC
24.0
mm/s
75%
Con�nuous
50%
Sel. temp. 325
º
C
Ø 1.00 mm
Supplied: 12 mm
Temp adjust
0ºC
Temp level set
Off
10min
0min
150ºC
Sleep delay
Peripher.
Sleep temp
Hiberna�on delay
Back
325
ºC
24.0
mm/s
25%
75%
Power
Con�nuous
50%
Sel. temp. 325
º
C
Ø 1.00 mm
Supplied: 12 mm
Plug hrs
28
Working hrs
Part
Tot
6
0
0
0
20
1
2
1
24
20
181
19
22786
118
Sleep hrs
Sleep cyc
Fed cyc
Fed mm
Hiber hrs
No tools hrs
ºC
24.0
mm/s
75%
Con�nuous
Sel. temp. 325
º
C
Ø 1.00 mm
Supplied: 12 mm
20.0mm/s
1.00mm
Off
5.0mm
Back
Con�nuous
325
ºC
24.0
mm/s
75%
Con�nuous
Sel. temp. 325
º
C
Ø 1.00 mm
Supplied: 12 mm
Plug hrs
28
Working hrs
Part
Tot
6
0
0
0
20
1
2
1
24
20
181
19
22786
118
Sleep hrs
Sleep cyc
Fed cyc
Fed mm
Hiber hrs
No tools hrs
Changing Guide Kits
Changing Wheels and Blade
For this operation, disconnect the device from the mains. Disconnect the tool from the control unit and open its cover.
First disassemble the guide tube (6), the nozzles (2)+(3), then the wheels, blade and clamp (4)+(5). Disassemble the counter wheel (1). Use the allen key and the spanner, provided with the station.
Assembly with Solder Wire Perforation:
Assemble the counter wheel (1).
Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
Assemble the inlet nozzle (3).
Assemble the guide wheel* (4) and tighten the scre w.
Assemble the blade first, then mount the blade clamp (5) onto the same axis and tighten the screw. Caution: handle the blade carefully to avoid injury.
Insert the guide set (6).
3
5
Blade
Inlet Nozzle
Interm. Nozzle
3
Inlet Nozzle
2
Guide Wheel*
Guide Wheel *
Intermediate Nozzle
4
Blade
4
4
Clamp
2
Blade
5
Blade Clamp
Assembly without Solder Wire Perforation:
Assemble the counter wheel (1).
Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
Assemble the inlet nozzle (3).
Assemble the support wheel* (4) onto the axis and tighten the screw.
Assemble the traction wheel (5) and tighten the screw.
Insert the guide set (6).
* wheel bears diameter marking
Suppor t Suppor t
Wheel * Wheel*
Interm. Nozzle
Intermediate Nozzle
4
4
2
2
Traction Wheel
Traction
5
Wheel
5
Inlet Nozzle
3
Inlet Nozzle
3
6
Counter Wheel
Counter Wheel
Guide Guide
Set Set
1
1
6
Counter Wheel
Counter Wheel
66
Guide
Guide
Set
6
Set
1
1
Replacing the Guide Tube
para manuales - color gris
Once the tool is disconnected from the control unit follow the instructions below:
Disassemble the outlet nozzle (1) from the guide tube.
Open the guide clamp (2), take off the guide tube (3) and insert the new one. Note: The guide tube length can be easily adjusted (4) when the guide clamp knob (2) is open.
Once the guide tube length is adjusted close the guide clamp knob (2).
Assemble the outlet nozzle (1) onto the guide tube tip.
Enter en “Tool Settings” at the SF control unit main menu and select the proper wire diameter.
Main MenuMain Menu
1 Reset settings 2
Station settings
3
Tool settings
4 Programs Settings
SF with Guide Tube assembled
Guide Tub e
4
1
Outlet Nozzle
SF with no Guide Tube assembled
3
Guide Tub e
2
Guide Clamp
Knob
7
Tool Assembly
Connect the tool to the control unit following this steps:
Insert and push the guide nozzle until the end (1) and tighten the screw (2).
Connect the jack (3).
1
Solder Wire Loading
Put the solder reel into its support (1).
Introduce the solder wire into the inlet nozzle (2) until it reaches the wheels (3).
Use the Tin Relo ad Process in the Mai n Me nu (4).
Main MenuMain Menu
1 Reset settings 2
Station settings
3
Tool settings
4 Programs Settings
5 Tin Reload Process 6 Counters 7 Software Version
ExitExit
The Relaod Procees screen opens. Press to star t the process.
Reload ProcessReload Process
Ba
ckward Forward
Press enter when finished
4
2
OK
Inser t to the end
To Guide Tube
3
Intermediate
Nozzle
5
3
2
1
Inlet Nozzle
Make sure the w ire passes throu gh the Interme­diate Nozzle and enters into the Guide Tube (5).
8
Notes
para manuales - color gris
9
Notes
10
Specifications
para manuales - color gris
GSF Guide Kits for SF280
With Perforation:
Ref.: GSF08V-B wire Ø 0.8 mm / Ø 0.032 in Ref.: GSF 10V-B wire Ø 1.0 mm / Ø 0.040 in Ref.: GSF12 V- B wire Ø 1.2 mm / Ø 0.047 in Ref.: GSF15V- B wire Ø 1.5 mm / Ø 0.059 in Ref.: GSF16V-B wire Ø 1.6 mm / Ø 0.063 in
Total Net Weight: Package Weight:
108 g / 0.24 lb 200 g / 0.44 lb 108 g / 0.24 lb 200 g / 0.44 lb 94 g / 0.21 lb 186 g / 0.41 lb 94 g / 0.21 lb 186 g / 0.41 lb 94 g / 0.21 lb 186 g / 0.41 lb
Without Perforation:
GSF04D-B for wire Ø 0.38 - 0.40 mm / Ø 0.015 - 0.016 in GSF05D-B for wire Ø 0.46 - 0.56 mm / Ø 0.018 - 0.022 in GSF06D-B for wire Ø 0.60 - 0.64 mm / Ø 0.023 - 0.025 in GSF07D-B for wire Ø 0.70 - 0.78 mm / Ø 0.028 - 0.031 in GSF08D-B for wire Ø 0.80 - 0.82 mm / Ø 0.032 - 0.033 in GSF10 D -B for wire Ø 0.90 - 1.10 mm / Ø 0.036 - 0.044 in GS F12D - B for wire Ø 1.14 - 1.27 mm / Ø 0.045 - 0.051 in GSF15D-B for wire Ø 1.50 - 1.57 mm / Ø 0.060 - 0.062 in GSF16 D-B for wire Ø 1.60 - 1.63 mm / Ø 0.063 - 0.065 in
GSF18 D -B for wire Ø 1.80 mm / Ø 0.073 in
- Guide Tube Length: 126 cm / 49.6 in
- Package Dimensions: 245 x 185 x 45 mm (L x W x H) 9.65 x 7.28 x 1.77 in
Complies with CE standards. ESD safe
104 g / 0.23 lb 196 g / 0.43 lb 104 g / 0.23 lb 196 g / 0.43 lb 104 g / 0.23 lb 196 g / 0.43 lb 104 g / 0.23 lb 196 g / 0.43 lb 104 g / 0.23 lb 196 g / 0.43 lb 90 g / 0.20 lb 182 g /0.40 lb 90 g / 0.20 lb 182 g /0.40 lb 90 g / 0.20 lb 182 g /0.40 lb 90 g / 0.20 lb 182 g /0.40 lb
11
Warranty
para manuales - color gris
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warrant y does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Get 1 extra year JBC warr anty by registering here: https://www.jbctools.com/productregistration/ within 3 0 days of purchase.
This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.
0028099-060922
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use