JBC Tools AT-SB Instruction Manual

INSTRUCTION MANUAL

ATS

Stand for AT420 Adjustable

Thermal Tweezers

This manual corresponds to the following references:

AT-SB

Packing List

The following items are included:

Stand for AT420 Adjustable Thermal Tweezers ............................................................................ 1 un it

Stand Cable 1m ............ 1 uni t

Ref. 0 024227

2

Sponge for Modular

Tool Stands ................... 1 unit

Ref. S7034

Brass Wool .................... 1 u ni t

Ref. C L6210

Manual ............................. 1 unit

Ref. 0028204

Features

para manuales - color gris

Cartridge Storage

Quick Tip Changer

Adjustable Tool Holder

Brass Wool

(inside)

Sponge

Control Unit

(not included, sold separately)

Adjustable
Cable Collector
Re f. C C10 01

Wiper for
Modular Tool Stand
Ref. C L7899

To Tool

3

Assembly

Cable Collector and Adjustable Tool Holder

Insert the cable into the cable

collector clip. Do not leave the

cable longer than necessary

to reach the work area freely.

The cable collector is flexible.

It accompanies and adapts

to the movements during the

soldering process.

Adjust the tool holder angle to

suit the work position.

The wiper offers different ways to
clean the cartridge tips. If desired

use the included sponge.

4

Wiper

para manuales - color gris

The integrated wiper offers different ways to clean the cartridge tips.

Tappin g Wiping Sponge

Tap gently to remove excess
solder.

Use the slots to remove the
remaining particles.

The softest cleaning method.
Keep the sponge damp with
distilled water when working to
avoid tip wear.

Wiper and Brass Wool Replacement

The wiper and brass wool can easily be removed for cleaning or replacement when they are worn.

Lift the wiper at its front edge.

Remove the wiper by pulling
it out.

Replace the brass wool with
a new one when it is worn
out.
Place the wiper back o replace
them if desired.

5

AT420

AT420

AT420

Changing Cartridges

1. Unlocking

2. Removing

AT420

Unlock the fixing screws.

Place the cartridges in the extractor (1) and pull
the tweezers to remove them (2).

3. Positioning 4. Inserting

Use the vertical grooves to position the
cartridges and place the tweezers onto the
cartridges.

Press the cartridges against the extractor and
make sure that the cartridge are inserted up
to the mark*.

2

1

*Important

It is essential to insert the cartridges as far as the mark for a proper connection.

Mark

6

AT420

OK

5. Rotational Cartridge

para manuales - color gris

Alignment and Locking

6. Vertical Cartridge Alignment

2

Rear Wheel

1

AT420

Slightly turn the wheels to align
the cartridges as required (1).
Then lock the catridge fixing
screws* (2).

AT420

The wheel allows the tips to be adjusted so that they are aligned
when the tweezers are closed.

aligned

*Once the alignment has been made, it is imperative to fix the cartridges by tightening the fixing

screws. It takes a single turn of the screw to lock it in place.

Accessories

Stand Extension Cable

Ref. A1286
Length: 1.5m

Stand Cable

7

Maintenance

Before carrying out maintenance or storage, always unplug the stand from the station and the tool.

- Use a damp cloth to clean the stand. Alcohol can be used only when cleaning the metal parts.

- Check periodically that the metal parts of the tool/stand are clean so that the station can check the
tool’s status.

- Periodically check all cables and tube connections.

- Replace any defective or damaged parts. Use original JBC spare par ts only.

- Repairs should only be per formed by a JBC authorized technical service.

Clean periodically

8

Safety

para manuales - color gris

It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to activate the sleep mode.

The soldering tip, the metal part of the tool and the stand may still be hot even when the station
is turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Avoid the contact of flux with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

9

Notes

10

Notes

para manuales - color gris

11

para manuales - color gris

Specifications

ATS
Stand for AT420 Adjustable Thermal Tweezers

Ref.: AT- S B

- Includes Sleep Mode and Hibernation Mode

- Net Weight 1544 g / 3.40 lb

- Package Dimensions / Weight 342 x 155 x 120 mm / 2106 g
(L x W x H) 13.5 x 6.1 x 4.7 in / 4.64 lb

Complies with CE standards
ESD Safe

Warranty

JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warrant y does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facilit y.

0028204-1221