jbc JCB-D800-2 Original Instructions Manual
SO53 3LE
Customer Helpline 0845 600 5526
SAFETY AND OPERATING MANUAL
HAMMER DRILL
JCB-D800-2
ORIGINAL INSTRUCTIONS
SO53 3LE
Customer Helpline 0845 600 5526
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety
warnings and all instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions
for future reference.
The term "power tool" in the
warnings refers to your electric
(corded) power tool or batteryoperated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well
lit.
Cluttered or dark areas invite
accidents.
b) Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust.
Power tools create
sparks which may ignite the dust
or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to
lose control.
2. Electrical safety
a) Power tool plugs must match
the outlet. Never modify the plug
in any way. Do not use any adapter
plugs with grounded power tools.
Unmodified plugs and matching
outlets will reduce risk of electric
shock.
b) Avoid body contact with
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of
electric shock if your body is
grounded.
c) Do not expose power tools
to rain or wet conditions.
Water
entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use.
Use of
a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a
damp location is unavoidable, use
a residual current device (RCD)
protected supply.
Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.
A moment of inattention while
operating power tools may result
in serious personal injury.
b) Use personal protective
equipment. Always wear eye
protection.
Protective equipment
such as dust mask, non-skid
SO53 3LE
Customer Helpline 0845 600 5526
SO53 3LE
Customer Helpline 0845 600 5526
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal
injuries.
c) Prevent unintentional starting.
Ensure the switch is in the offposition before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energising
power tools that have the switch
on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on.
A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of
the power tool in unexpected
situations.
f) Dress properly. Do not wear
loose clothing or jewellery. Keep
your hair, clothing and gloves
away from moving parts.
Loose
clothes, jewellery or long hair can
be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a) Do not force the power tool.
Use the correct power tool for
your application.
The correct
power tool will do the job better
and safer at the rate for which it
was designed.
b) Do not use the power tool if
the switch does not turn it on and
off.
Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from
the power source and/or the
battery pack from the power tool
before making any adjustments,
changing accessories, or storing
power tools.
Such preventive
safety measures reduce the
risk of starting the power tool
accidentally.
d) Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool.
Power
tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use.
Many
accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and
clean.
Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier
SO53 3LE
Customer Helpline 0845 600 5526
to control.
g) Use the power tool,
accessories and tool bits
etc. in accordance with these
instructions, taking into account
the working conditions and the
work to be performed.
Use of the
power tool for operations different
from those intended could result
in a hazardous situation.
5. Service
a) Have your power tool serviced
by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained.
b) If the replacement of the
supply cord is necessary, this has
to be done by the manufacturer or
its agent in order to avoid a safety
hazard.
SO53 3LE
Customer Helpline 0845 600 5526
ADDITIONAL SAFETY POINTS FOR YOUR HAMMER DRILL
1. Remove the plug from the
socket before carrying out
any adjustment, servicing or
maintenance.
2. Fully unwind cable drum
extensions to avoid potential
overheating.
3. When an extension cable is
required you must ensure it has
the correct ampere rating for your
power tool and that it is in a safe
electrical condition.
4. Ensure your mains supply
voltage is the same as your tool
rating plate voltage.
5. Your tool is double insulated
for additional protection against
a possible electrical insulation
failure within the tool.
6. Always check walls and
ceilings to avoid hidden power
cables and pipes.
7. After long working periods,
external metal parts and
accessories could be hot.
8. Wear eye protection when
operating this tool.
9. Wear ear protectors with
hammer drills. Exposure to noise
can cause hearing loss.
10. Maintain a firm grip on the
handle when you are working.
Always use the auxiliary handles
supplied with the tool. Loss of
control can cause personal injury.
11. Hold tool by insulated
gripping surfaces when
performing an operation where
the cutting tool may contact
hidden wiring. Contact with a
“live” wire will also make exposed
metal parts of the tool “live” and
result in operator injury.
12. Do not use the drill near water.
Loading...