DDR
2 TOOLS CONTROL UNIT
FOR ROBOT
www.jbctools.com
2
DDR / 2 TOOLS CONTROL UNIT FOR ROBOT
POWER CORD MANUAL MANUAL MANUAL*
*Download the Robot Comunication Protocol at http://www.jbctools.com/downloads.html
**We recommend to isolate the RS-232 comunication electrically.
0002747
CONVERTER
T470-SA
HANDPIECE
Connectable tools: T210, T245, T470 (only C245 cartridges), PA120,
HT420, AP130, DR560 and DS360.
Connectable modules: MS, MV and MN.
INSTALLATION
Power Cord
Socket
RS-232**
Interface
USB Connector
to PC
DDR
2 TOOLS CONTROL UNIT
T210 ·T24 5·T470
SOLDERING HANDPIECES
DDR-2B / 1B / 9B
CONTROL UNIT
Equipotential
connector
This converter allows users to connect a T210, T245 or
T470 handpiece directly to the station witouth the need
of using a stand.
www. jbc tool s.co m
www. jbc tool s.co m
3
Main me nu
Count er s
Tool se tt in gs
Exit
1 Reset settings
2
Station settings
3
Tool settings
1
Plugged hours 0
2
Working hours 0
3
Sleep hours 0
1
Fix one temp -----
2
Temp levels set OFF
3
Sleep delay 0 min
4 Counters
5
Program version
4
Hibernation hours 0
5
No tool hours 0
6 Sleep cycles
0
7 Desold cycles
0
4
Sleep temp 1800C
5
Hibernation delay 30 min
6
Temp adjust O OC
Tool DR
Port 1
Port 1/2
Port 1/2
Tool DR
Port 1
Back
Back
0
c
Selected temp.
350 oC
P ow e r 1 0%
350
Decrease & move down Increase & move up
Tip temperature
% Instant power supplied to the tool
ORIGINAL PIN: 0105
Stati on set ti ng s
1 Temp unit
Celsius
2
Maximum temp 4000C
3
Minimum temp 2000C
4
Nitrogen mode OFF
Back
Access Menu
&
Confirm
Selection
CONTROL SCREEN
SETTINGS MENU
When the Robot Setting is set to ON,
the functions Sleep and Extractor are
disabled as well as the USB comunication
5
Help text OFF
6 Beep ON
7 Robot ON
8 Power limit 150W
9
Change PIN
WARRANTY
JBC’s 2 years warranty guarantees this equipment against all manufacturing defects, covering the replacement of defective parts and
all necessary labour.
Warranty does not cover product wear due to use or mis-use.
In order for the warranty to be valid, equipment must be returned,
postage paid, to the dealer where it was purchased enclosing this
fully filled in, sheet.
www.jbctools.com
SERIAL Nº
STAMP OF DEALER
DATE OF PURCHASE
0012262-0912
TECHNICAL SPECIFICATIONS
- Temperature selection from 90ºC (190ºF) to 450°C (840ºF) (±5%).
- Output Peak Power: 150W
- Safety transformer, mains separator and double isolation.
- DDR-2B 230V 50/60Hz. Input fuse: 2A. Output: 23,5V.
- DDR-1B 120V 50/60Hz. Input fuse: 4A. Output: 23,5V.
- DDR-9B 100V 50/60Hz. Input fuse: 4A. Output: 23,5V.
- Total weight of unit: 3.5Kg (7,7lb)
- Complies with CE standards on electrical safety, electromagnetic compatibility
and ESD protected housing “skin effect”.
- RoHS compliant.
- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.
This product should not be
thrown in the garbage.
Loading...